SATPC0035288 Tab 04 4 SOW_Redacted.pdf
PDF 213 KB Posted
- Attached to
- imc Dataworks Rotorcraft Telemetry System Federal contract opportunity
- Solicitation number
- 80NSSC24872379Q
About this file
This document is a Statement of Work (SOW) for the procurement of the imc Dataworks Rotorcraft Telemetry System by the NASA Langley Research Center. The requirements specify the purchase of the MTP-NT-BASE controller with transmitter and power module, as well as the MTP-NT-ANALOG4 acquisition module with 4 channels that can be independently configured for various sensor types. The system will be used for wind tunnel testing.
The related federal contract opportunity is a sole source procurement from IMC DATAWORKS, LLC. NASA/NSSC intends to issue a sole source contract under the authority of FAR 13.106-1(b)(1)(i), as IMC DATAWORKS, LLC has been determined to be the sole provider of the required Rotorcraft Telemetry System. The NAICS code for this procurement is 541511. The government intends to acquire the commercial items and services using the provisions of FAR Part 12 and FAR Part 13. Interested organizations may submit their capabilities and qualifications to the identified points of contact by 6/14/2024, which will be evaluated to determine if the procurement should be conducted on a competitive basis.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| SATPC0035288 Tab 04 4 SOW REVISED_Redacted.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
STATEMENT OF WORK
1. Objective/Requirements
NASA Langley Research Center requires the purchase of the imc Dataworks Rotorcraft Telemetry System which will be used for wind tunnel testing.
2. Characteristics, Scope, and Specs
Product # Description Qty
IMC-3RD-HW
MTP-NT-BASE, 13220413 Controller with inductive transmitter and Power module in one MTP-NT housing 1
MTP-NT-ANALOG4,
13220003
Acquisition module for STG / Volt / Potentiometer / IEPE - 4 channels Each channel can be set to STG/VOLT/POT/IEPE independently Bandwidth 0...12(24*) kHz (See table of cut-off frequencies) 18 bit resolution Gain uncertainty <0.1 %; Offset drift <0,1% FS Power supply 6 to 9 Vdc Current consumption 240 to 320 mA (depends on sensor type) Dimensions 60 x 40 x 18 mm Weight 65 g Standard temperature range -40...+85°C
STG
Full, half and quarter bridge configuration, ≥120 Ω Internal quarter bridge completion for 120 Ω and 350 Ω Measurement ranges ±0,3 mV/V to ±40 mV/V Shunt calibration 100/300 kΩ 0.1% Excitation Voltage 4.0 V Automatic and manual offset compensation
VOLT
Measurement range ±0,3 V to ±10 V Supply for external sensor 12 V / ≤30 mA (programmable) Input resistance 667 kΩ
POT
Potentiometer resistance ≥120 Ω Fixed excitation voltage 4.0 Vdc Input resistance 667 kΩ
IEPE
Measurement range ±0,3 V to ±10 V Lower cut-off frequency 3 Hz Excitation current 4 mA
CABLE-NT-SENSOR-220,
13220016
Signal input cable (standard length) Type of sensor STG, voltage or POT Sensor cable with open end Length 220 mm 2 x 4pole
CABLE-NT-BUSS,
13220012
Bus cable for MTP-NT modules S Length 120 mm 8
DEC-ANA-32-IND,
13220034
Decoder for 32 channels with two inductive pickups inputs PCM decoder for up to 32 channels 2 pickup inputs Output via 37-pole D-SUB connector BNC-32 connection box must be ordered separately The decoder internal receiver must be ordered separately
IND-Rx-2.5M-45MHz, 13220006
Inductive receiver 2.5 Mbit/s Inductive receiver with 45 MHz carrier frequency Data rate up to 2.5 Mbit/s This board is installed in the decoder housing Standard temperature range -40...+85 °C
CHANGE-LEMO-
7PIN-DECODER,
13220405
Design of the connection for data heads as LEMO 1.B 7-pin socket on the decoder or PCM receiver, instead of LEMO 1.B 6-pin socket only together with new decoder or PCM receiver
ACC/FGG.1B.307-
3.1-4.2, 13500405 Plug LEMO.1B, 7 pins, FGG series, IP50 for cable size 3.1mm to 4.2mm
Error+Signal-LED-via-
DSUB,
13220389
Error & Signal LED via DSUB on Decoder Output of the Error & Signal LED signals from the front of the decoder via 9-pin D-SUB Extension for DEC-ANA-16-IND
AC/DC-24V-1AUS,
13220059
AC/DC power supply US for the decoder, IP-LAN-Interface, HF-Box ...
Voltage 24 V Power 24 W Tuchel connector (7-pole) US plug
CABLE-DC-POWER,
13220037
DC power cable for decoders (receiver) Banana plugs Tuchel connector (7-pole) Lenght 2 m
BNC32 BOX,
13220035
BNC - 32 junction box (optional) 37-pin D-SUB to 32 individual BNC connectors
MTP-NT-CONFIGSET,
13220018
Configuration Set To connect the controller to the PC RS232 / USB adapter with connection cable, 1 m length
Config-Control, 13220142
Software Software package for setup/parameterisation the telemetry modules
3. Place of Performance
NASA Langley Research Center 218 Dodd Blvd.
MS 340
Hampton VA, 23681
4. Period of Performance
60 days ARO
File details come from the government source that posted it. Updated .