SATPC0035288 Tab 04 4 SOW REVISED_Redacted.pdf
PDF 214 KB Posted
- Attached to
- imc Dataworks Rotorcraft Telemetry System Federal contract opportunity
- Solicitation number
- 80NSSC24872379Q
About this file
The provided document is a Statement of Work (SOW) for the purchase of the imc Dataworks Rotorcraft Telemetry System, which will be used for wind tunnel testing at the NASA Langley Research Center. The SOW details the specific characteristics, scope, and specifications of the required product, including the MTP-NT-BASE controller module, MTP-NT-ANALOG4 acquisition module, and associated technical details such as frequency, bitrate, power supply, dimensions, and temperature range.
The related federal contract opportunity is a Special Notice solicitation (Solicitation Number: 80NSSC24872379Q) issued by the National Aeronautics and Space Administration (NASA) Shared Services Center. The government intends to acquire these commercial items and services using FAR Part 12 and FAR Part 13 procedures, and plans to award a sole source contract to IMC DATAWORKS, LLC, the sole provider of the required imc Dataworks Rotorcraft Telemetry System. Interested organizations may submit their capabilities and qualifications to the designated point of contact by 6/14/2024 for the government's consideration of a competitive procurement approach.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| SATPC0035288 Tab 04 4 SOW_Redacted.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
STATEMENT OF WORK
1. Objective/Requirements
NASA Langley Research Center requires the purchase of the imc Dataworks Rotorcraft Telemetry System which will be used for wind tunnel testing.
2. Characteristics, Scope, and Specs
Product # Description Qty
MTP-NT-BASE-S, 13220413
MTP-NT-BASE: Controller with inductive transmitter and Power module in one MTP-NT housing module on the top: MTP-NT-CONTROLLER PCM output Carrier frequency 45 MHz Bitrate from 312.5 kBit/s up to 10 MBit/s Programmable via RS232/USB adaptor Power supply 6...9 V DC Current consumption 100 mA module at the bottom: MTP-NT-POWER-S Input DC or AC 30...60kHz, 9-35 Vrms, 24-100 Vpp, 12-50Vdc Output 6 V, max. 2400 mA Dimensions 60 x 40 x 18 mm Weight 65 g Standard temperature range -40...+85°C
MTP-NT-ANALOG4,
13220003
Acquisition module for STG / Volt / Potentiometer / IEPE - 4 channels Each channel can be set to STG/VOLT/POT/IEPE independently Bandwidth 0...12(24*) kHz (See table of cut-off frequencies) 18 bit resolution Gain uncertainty <0.1 %; Offset drift <0,1% FS Power supply 6 to 9 Vdc Current consumption 240 to 320 mA (depends on sensor type) Dimensions 60 x 40 x 18 mm Weight 65 g Standard temperature range -40...+85°C
STG
Full, half and quarter bridge configuration, ≥120 Ω Internal quarter bridge completion for 120 Ω and 350 Ω Measurement ranges ±0,3 mV/V to ±40 mV/V Shunt calibration 100/300 kΩ 0.1% Excitation Voltage 4.0 V Automatic and manual offset compensation
VOLT
Measurement range ±0,3 V to ±10 V Supply for external sensor 12 V / ≤30 mA (programmable) Input resistance 667 kΩ
POT
Potentiometer resistance ≥120 Ω Fixed excitation voltage 4.0 Vdc Input resistance 667 kΩ
IEPE
Measurement range ±0,3 V to ±10 V Lower cut-off frequency 3 Hz Excitation current 4 mA
CABLE-NT-SENSOR-220,
13220016
Signal input cable (standard length) Type of sensor STG, voltage or POT Sensor cable with open end Length 220 mm 2 x 4pole
CABLE-NT-BUSS,
13220012
Bus cable for MTP-NT modules S Length 120 mm 8
DEC-ANA-32-IND,
13220034
Decoder for 32 channels with two inductive pickups inputs PCM decoder for up to 32 channels 2 pickup inputs Output via 37-pole D-SUB connector BNC-32 connection box must be ordered separately The decoder internal receiver must be ordered separately
CHANGE-LEMO-
7PIN-DECODER,
13220405
Design of the connection for data heads as LEMO 1.B 7-pin socket on the decoder or PCM receiver, instead of LEMO 1.B 6-pin socket only together with new decoder or PCM receiver
ACC/FGG.1B.307-
3.1-4.2, 13500405 Plug LEMO.1B, 7 pins, FGG series, IP50 for cable size 3.1mm to 4.2mm
Error+Signal-LED-via-
DSUB,
13220389
Error & Signal LED via DSUB on Decoder Output of the Error & Signal LED signals from the front of the decoder via 9-pin D-SUB Extension for DEC-ANA-16-IND
AC/DC-24V-1AUS,
13220059
AC/DC power supply US for the decoder, IP-LAN-Interface, HF-Box ...
Voltage 24 V Power 24 W Tuchel connector (7-pole) US plug
CABLE-DC-POWER,
13220037
DC power cable for decoders (receiver) Banana plugs Tuchel connector (7-pole) Lenght 2 m
BNC32 BOX,
13220035
BNC - 32 junction box (optional) 37-pin D-SUB to 32 individual BNC connectors
MTP-NT-CONFIGSET,
13220018
Configuration Set To connect the controller to the PC RS232 / USB adapter with connection cable, 1 m length
Config-Control, 13220142
Software Software package for setup/parameterisation the telemetry modules
3. Place of Performance
NASA Langley Research Center 218 Dodd Blvd.
MS 340
Hampton VA, 23681
4. Period of Performance
60 days ARO
File details come from the government source that posted it. Updated .