SALIENT CHARACTERISTICS.pdf

Salient Characteristics for a Steam Cleaner Project #327-340

June 6, 2025

1. Steam Cleaner (Ben’s Cleaner Sales, Inc. Natural Gas Fired Steam Cleaner, Item #BENS-300UL-TURNKEY, or equal). The Steam Cleaner shall include the following minimal capabilities/features/items:

a. Steam Pressure - 400 psi

b. Steam Capacity - 300 gal/hour

c. Motor Voltage – 230V, Single Phase, Amp Requirement - 20 amp

d. Horsepower - 4 hp

e. Fuel Source - Natural Gas / LP

f. Gas Burner, Natural Aspirating - 1040000 Btu

g. Natural Gas Consumption - 990 ft³/h

h. Pump Style - Oil Bath Crankcase Triplex

i. Ceramic Plunger

j. Coil Type - Schedule 40

k. Coil Construction Type - Hydro insulated cold water wrap

l. Coil Length - 515 ft

m. Coil Inner Diameter - 3/4 in

n. Wand Type - Open-Standard

o. Float Tank Construction Material – Stainless Steel

p. Standard Parts/Features – Temperature Control

q. Chemical Features - High Pressure Precise Metered

r. Hose Length - 50 ft

s. Hose Diameter - 3/8 in

t. Unit Size (+/- 10%):

1). Length - 56 in 2). Width - 30 in 3). Height - 71 in

u. Weight - 1385 lbs (+/- 10%)

2. Removal/Installation shall include parts and labor to:

a. Disconnect Utilities (gas, electrical, water, and venting)

b. Remove and dispose existing Steam Cleaner (Manufacturer: Alkota, NID #:

68438G1075, Serial #:282175)

c. Install new Steam Cleaner

d. Reconnect Utilities (gas, electrical, water, and venting)

e. Run and test steamer for proper operation, and provide simple operational and maintenance instruction.

3. Safety Requirement - The equipment and its component parts shall be in compliance with applicable Code of Federal Regulations (CFR) Title 29, Part 1910. By definition, any equipment will be deemed acceptable and approved by TRF, Bangor, if it meets specific Occupational Safety and Health Administration (OSHA) conditions outlined in CFR Title 29, Part 1910; Subparts "O" and "S".

Specifically, equipment will be "Accepted" by TRF, Bangor, if it has been inspected and found by a Nationally Recognized Testing Laboratory (NRTL) to conform to specified plans or procedures of applicable codes. The equipment (as a whole system) shall be Nationally Recognized Testing Laboratory (NRTL) inspected and certified (by an OSHA authorized third party). Two (2) “hard” copies of the NRTL certification report shall be provided. If the equipment type/model has already been NRTL inspected and certified, a certification report (two (2) ”hard” copies) or documentation mounted on the equipment, (which acknowledges it is NRTL certified), shall be provided.

4. Operator / Maintenance / Repair Manuals - The equipment shall be furnished with two (2) “hard” copies of the manufacturer’s standard Product Manual/Operation, Maintenance, and Repair Manual(s), bound in durable three ring binder(s). The manuals shall include all mechanical and electrical schematics showing discrete components/block diagrams/wiring diagrams with inputs and outputs identified/system electrical interface documents and drawings for the specific model of all machine equipment/drives/controls supplied. The information contained in the manual(s) shall reflect the unit and its components in the “as built” configuration. The information contained in the manual(s) shall be adequate to permit trouble shooting and repair of the equipment by journeymen level personnel. The information contained in the manual(s) shall be in the English language. The information contained in the manual(s) shall be in imperial units of measure. The vendor shall provide a “no asbestos used” statement, certifying that all products/materials (i.e. gaskets, etc.) used in the components of the equipment does not contain asbestos. The contractor shall provide a list of recommended consumable spare parts and possible sources for procurement.

5. Warranty - Two (2) “hard” copies of the warranty certificate shall be provided. Supplies and services furnished shall be covered by warranty from defects in design, materials and workmanship. The warranty shall be the manufacturer’s standard commercial warranty, which shall conform to all the requirements of the contract. Acceptance of the manufacturer’s standard commercial warranty shall not minimize the rights of the government under clauses in the contract, and in any conflict that arises between the terms and conditions of the contract and manufacturer’s warranty, the terms and conditions of the contract shall take precedence. The warranty period shall be for 1 year. The warranty period shall commence from the date of acceptance. All warranty work shall be provided by a factory authorized distributer.

6. Admittance To The Work Site:

a. Upon contract award, employees or representatives of the Contractor who require access to the Receiving Activity's facility at Naval Base Kitsap, Bangor (NBK, Bangor) shall be admitted to the work site only after they have been issued an appropriate Naval Region NW visitor security badge which is obtained at NBK, Bangor Pass & ID Office (located outside the NBK, Bangor Trident/ Main Gate).

b. Navy Region NW badge is required to gain access to Trident Refit Facility (TRF) Bangor Site, and is obtained through the “on-line” Base Authorization and Visit Request (BAVR) computer system. The prime contractor will need to submit all badge requests for their personnel and for sub-contractor personnel.

c. To request a Navy Region NW badge, (use Internet Explorer or Microsoft Edge browsers) and go on line to https://www.bavr.cnic.navy.mil. After the web site comes up, click “APPLY FOR NEW BADGE” button and submit a request for a badge, a minimum of five business days prior to arrival. All requested information highlighted in red is mandatory. Type N/A for “Driver’s License Information”. The "Command you are visiting" is: Trident Refit Facility TRF).

The “Company Name or Command” and “Work Phone” is your company/command information. The “Originating Command Security Officer Information” should be left blank. The "Sponsor E-Mail" for an on-line badge should be: aaron.k.peal1@navy.mil (Aaron Peal, 360-315-1047, 360-471-8624 (cell)). In the "Purpose of Visit" box, please explain in detail the purpose of your visit, and include the Contract Number, the Receiving Activity Point of Contact (name and telephone number) and ALL the buildings/areas/piers you are visiting.

The “Start Date” is the day you expect to pick up your badge. The “End Date” is the last date of your visit. Also send a copy of the contract to Aaron Peal at the e-mail address listed above. You will be notified at the e-mail address you provided, when all approvals have been completed. If the BAVR computer system doesn't work, try different search engines (“Firefox” search engine seems to work the best). If BAVR still doesn’t work contact the Receiving Activity Point of Contact or our security manager, Aaron Peal, 360-315-1047, 360-471-8624 (cell) to schedule a visit(s), and shall provide the following information:

* Full Legal Name

* US Citizen Status

* All Company Contact Information

* Contract Number

d. Visitors must show proof of US Citizenship (at the NBK Bangor Pass & ID Office, located outside Bangor’s Main Gate (Trident Boulevard), with office hours: Monday – Friday, 7:00 am – 3:00 pm), by having an original active US Passport, OR an "Enhanced Driver's License" (from Washington, Vermont, Michigan, Minnesota or New York), OR an unlamented official birth certificate.

“Real IDs” are not accepted.

e. Truck delivery personnel only need to show their Bill of Lading and show proof of US Citizenship (at the NBK Bangor Pass & ID Office) by having an original active US Passport, Enhanced Driver's License, or an unlamented official birth certificate. All deliveries must pass through the base Truck Inspection Station. All delivery vehicles are subject to inspection. Drivers should expect delays due to heightened security.

f. Notice: Persons who are currently on probation or parole from a felony conviction cannot qualify for security clearances, and will be denied access to the activity.

g. It shall be the Contractor's responsibility to collect, account for all identification passes issued to their personnel at the expiration of the contract or when access is no longer required. All NBK Bangor Pass & ID Office issued badges and identification passes must be returned back to the NBK Bangor Pass & ID Office no later than the expiration date. Badges can be dropped off at the NBK Bangor Pass & ID Office, or drop box located at the Main Gate (Trident Boulevard), when exiting the base by vehicle (outside lane), or mailed back to the site POC.

h. Foreign Nationals or Affiliations - Foreign Nationals (non U.S. Citizens) or persons affiliated with, or employed by, a foreign, or foreign owned company will not be granted access without proper NBK Bangor Commanding Officer's written approval. Please note that All NBK Bangor Command Foreign Nationals or Affiliations visit request must be submitted sixty (60) days prior to a requested visit date.

i. Identification. All Contractors shall clearly identify themselves as contactor personnel. Badging shall be attached to the front side of clothing above the waist, or on a lanyard worn around the neck, hanging on the front side of clothing.