Salient Characteristics 620A4 18 212.pdf

LIST OF BRAND NAME OR EQUAL EQUIPMENT -

MAKE, MODEL AND SALIENT CHARACTERISTICS

Reference: Section – 23 74 13

Item: CUSTOM OUTDOOR CENTRAL STATION AIR HANDLING UNITS

Vendor: Innovent Air Handling Equipment

Model: CAHU-3315-IB-HM-CW-CW-208

Salient Characteristics:

• CASING

Leakage rating of less than 1% of design air flow at 10” total static pressure

Maximum panel deflection shall not exceed L/400 at design total static pressure

Minimum R-25 insulation value for walls, ceilings, and flooring

4” thick double wall thermal-break panels, 0.063” aluminum outer wall, 0.040” aluminum inner wall

2 lb/ft3 polyurethane foam injected insulation in the walls and ceiling

Designed for outdoor installation

0.063” aluminum pitched roof

Unit shall be shipped in 3 sections. Sections shall be reassembled by others in the field. All silicone, gasketing, flashing and fasteners required to reassemble the unit sections shall be provided and shipped loose inside the unit sections.

• FLOOR

Floor shall be 2” thick paneled construction with 0.072” aluminum treadplate walk-on surface and 22 gage galvannealed steel welded to bottom of base (not exposed to air stream)

2 lb/ft3 polyurethane foam injected insulation

Safety grating provided for duct penetrations through the unit floor

• FRAME & STRUCTURAL BASE

Frame and panel construction provided with aluminum structural tube framing members

10 ga coated welded steel structural base

Lifting lugs mounted on unit base

• ACCESS

Double wall insulated access doors with stainless steel hinges, corrosion resistant compression latches

Doors shall be tool lockable

Doors shall have thermal break design (all doors)

Doors shall have pressure relief safety latches (doors that open with pressure)

• UNIT INLETS/OUTLETS

Supply air outlet with duct connection

Outside air inlet with weather hood and aluminum bird screen

• CHILLED WATER COIL 2

Chilled water coil stainless steel casing, 0.02 thick copper tubes ad 0.008 thick aluminum fins

Coil tubes provided with turbulators

Stainless steel IAQ drain pan

Supply and return connections supplied with copper sweat fittings

Water control valve is provided by others and field mounted by others (valves must accept

0-10 VDC control signal, 24 VAC Power supply

• CHILLED WATER COIL

AHRI rated chilled water coil with stainless steel casing, 0.02 thick copper tubes, and 0.008 thick aluminum fins

Coil tubes provided with turbulators

Stainless steel IAQ drain pan

Supply and return connections supplied with grooved steel connection

Water control valve is provided by others and field mounted by others (valves must accept

0-10 VDC control signal, 24 VAC Power supply

• SUPPLY FAN

Airfoil plenum fan, welded aluminum wheel

AMCA certified ratings for sound and performance

Direct drive assembly

1” spring isolated unitary fan/motor base, flex connectors provided at fan inlet

TEFC premium efficiency motors

VFD-rated with class F insulation

Shaft grounding is provided with each motor

• OUTSIDE FILTER

2” pleated MERV 8 filter

12” cartridge MERV 11 filter

Front access filter rack construction to be aluminized steel

• SUPPLY FILTER

12” cartridge MERV 15 filter

Front access filter rack construction to be aluminized steel

• DAMPERS

Supply fan isolation: aluminum airfoil blade, aluminum frame, two-position actuator

Outside air inlet: aluminum airfoil blade, aluminum frame, two-position actuator

Supply air outlet: aluminum airfoil blade, aluminum frame, two-position actuator

Motorized dampers:

AMCA certified performance

Leakage rating of 3 CFM/FT2 at 1” wg

Synthetic bearings

• INTEGRAL FACE/BYPASS STEAM COIL

Steam coil with stainless steel casing, 0.02 thick copper tubes, and 0.008 thick aluminum fins

Steam valve provided by others and field mounted by others

• HUMIDIFIER MANIFOLD

Tubes and headers constructed of 304 stainless steel

Control valve, strainer, and Float and Thermostatic steam traps provided by the equipment manufacturer and installed by others

• ELECTRICAL

Unit ETL listed as complete package, unit factory wired to unit mounted NEMA 3R control panel

Major electrical components UL listed (non-fused disconnect switch, control circuit fusing, control circuit transformer, fan motor starters, and overloads as applicable)

Power wiring enclosed in conduit

Single point power connection

Unit shall have a short circuit current rating (SCCR) of 5 kA

IP67 rated LED light strips provided as shown on unit drawing are wired to a single light switch, 120V transformer included to power the lighting circuit

A VFD per supply fan is provided by Innovent and factory installed by Innovent

No manual bypass included

Variable frequency drive shall be ventilated by the unit air stream

All power wiring shall be coiled into the section with its respective electrical component.

Field extension of wire through air handler tunnel and termination of wires at the control panel shall be by others.

Unit shall be fully factory wired for testing purposes with labeled quick connections at section splits. After testing, all control wiring will be disconnected at section splits and placed inside a junction box. Field reconnection of wires shall be by others after the unit is set.

• CONTROLS

A fully-programmed Carel DDC controller is provided.

A standard Innovent sequence of operation will be provided. Any customization of the standard sequence will require factory approval

Type of BMS interface to be specified to Innovent at or before the release of the job.

Sensors/transducers/switches are provided and installed by Innovent

• EQUIPMENT MOUNTING

36” high, custom, insulated plenum roof curb by Curb Technologies (via the AHU manufacturer)

• ETL LISTING

ANSI/UL 1995: Heating and Cooling Equipment

• WARRANTIES

All Innovent warranties begin at equipment start-up or 6 months from shipment, whichever occurs first.

1 year PARTS ONLY unit warranty is provided per Innovent’s standard warranty terms

• FACTORY TESTING/REPORTS

Standard run testing done

• START UP

Start up by others

• MISCELLANEOUS

Multiple floor openings for supply and return air

Justification: The manufacturer is identified as the design basis as a single source to ensure total system compatibility and integrity.

BIDDING ON: ____________________________________

MANUFACTURER

NAME: ____________________________________

BRAND: ____________________________________

NO.: ____________________________________

Reference: Specification Section - 22 40 00; Drawing P121 and P501, mark P531 Item: WASH UP SINK WITH EMERGENCY EYEWASH - ADA COMPLIANT – HANDS FREE

Vendor: Just Manufacturing Model: JPH-ADA-2224-CT

Justification: The manufacturer is identified as the design basis as a single source to ensure total system compatibility and integrity. Provide an alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 22 67 19.16, Drawing P-501 mark 15H-RO-1, M131 Keynote 11 & P121

ITEM: HUMIDIFICATION CLEAN STEAM RO WATER

Vendor: Dristeem Model: RO-202

Salient Characteristics:

Product capacity – Prefilters 1 GPM, Multistage single pass 0.5 GPM/200 lbs

Per Hour, Bladder Tank 4.5 gallons

Feed Flow – 1 GPM

Low to Drain – 0.5 GPM

No of Vessels per units – 2

Membranes per Vessel – 1

Vessel Array – Series

Electrical – 5.5 Amps, single phase, 120V

Justification: The manufacturer is identified as the design basis as a single source to ensure total system compatibility and integrity. Provide an alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 82 16, Drawing MP-121 mark 3-RHC-1

ITEM: HOT WATER HEATING COIL

Vendor: Heat Craft Model: 5MI6002A 16.5”H 16”L

Salient Characteristics:

Air Flow – 905 CFM

Face Velocity – 484 FPM

APD – 0.08 IN WG

Temperatures – 60 degrees F EAT, 86.2 degrees F LAT

Total Min Capacity – 25.7 MBH

Rows – 2

Fins per Inch – 6

Hot Water – Flow 2.1 GPM, EWT 160 Degrees F, LWT 135 degrees F, WPD 0.5 FT, 0% Glycol alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 82 16, Drawing MP-121 mark 3-RHC-2

Vendor: Heat Craft Model: 5MI0602A 13.5”H 12”L

Salient Characteristics:

Air Flow – 570 CFM

Face Velocity – 497 FPM

APD – 0.09 IN WG

Temperatures – 60 degrees F EAT, 84.6 degrees F LAT

Total Min Capacity – 15.2 MBH

Rows – 2

Fins per Inch – 6

Hot Water – Flow 1.3 GPM, EWT 160 Degrees F, LWT 136 degrees F, WPD 0.2 FT, alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 82 16, Drawing MP-121 mark 3-RHC-3

Vendor: Heat Craft Model: 5MI0602A 10.5”H 8”L

Salient Characteristics:

Air Flow – 255 CFM

Face Velocity – 429 FPM

APD – 0.08 IN WG

Temperatures – 60 degrees F EAT, 82.5 degrees F LAT

Total Min Capacity – 6.2 MBH

Rows – 2

Fins per Inch – 6

Hot Water – Flow 0.6 GPM, EWT 160 Degrees F, LWT 139 degrees F, WPD 0.01 FT, alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 82 16, Drawing MP-121 mark 3-RHC-4

Vendor: Heat Craft Model: 5MI0602A 13.5”H 14”L

Salient Characteristics:

Air Flow – 640 CFM

Face Velocity – 478 FPM

APD – 0.07 IN WG

Temperatures – 60 degrees F EAT, 85.7 degrees F LAT

Total Min Capacity – 17.8 MBH

Rows – 2

Fins per Inch – 6

Hot Water – Flow 1.5 GPM, EWT 160 Degrees F, LWT 136 degrees F, WPD 0.3 FT, alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 82 16, Drawing MP-121 mark 3-RHC-5

Vendor: Heat Craft Model: 5MI0602A 16.5”H 16”L

Salient Characteristics:

Air Flow – 860 CFM

Face Velocity – 460 FPM

APD – 0.07 IN WG

Temperatures – 60 degrees F EAT, 86.9 degrees F LAT

Total Min Capacity – 25.1 MBH

Rows – 2

Fins per Inch – 6

Hot Water – Flow 2 GPM, EWT 160 Degrees F, LWT 135 degrees F, WPD 0.5 FT, 0%

Glycol alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 64 00, Drawing M-131 mark 15H-CH-1

ITEM: AIR COOLED CHILLER

Vendor: Trane Model: CGAM026A2

Salient Characteristics:

Capacity – 26 Tons

# of Comp - 2

Max kW/Ton – 0.86

Propylene Glycol - 45%

Total Min Capacity – 25.1 MBH

Max IPLV (kW/Ton) – 0.86

Evaporator - Flow – 54.2 GPM, EWT – 53 deg F, LWT – 42 deg F, Max WPD – 21

FT, Fouling Factor – 0.0001

Condenser - Ambient OA Temp of 95 deg F

Compressor Motor (Electrical) - 2 Comp, 3 phase, 208V

Condenser Fan Motor (Electrical) – 2 Fans, Nominal 2 HP, 3 phase, 208V

MCA – 148Amps

MOCP – 175 Amps alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 05 12, Drawing MP-121 - mark 15CSG-1, miss-labeled as 15CSG-2-3 on M-701

ITEM: CLEAN STEAM GENERATOR

Vendor: Dristeem Model: 100S

Salient Characteristics:

Source of makeup – RO

Water Conditions - 0.19 GPM of flow, EWT 40 degrees

Produced Steam Flow – 96 Lbs per HR

Produced Steam Press – 15 PSIG

Steam Pressure – ENT Control Valve 15 PSIG, ENT Heat Exchanger 15 PSIG

Control Valve – 91 Lbs per Hr

Trap – Qty 1, 200 lbs per Hr alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 36 00, Drawing M701 & MP-121 - mark 3UH-1

ITEM: STEAM UNIT HEATER

Vendor: Trane Model: UHSBS-018

Salient Characteristics:

Air Flow – 330 CFM

Min Capacity 16,200 BTUH

Temperatures – EAT 60 Deg F, EWT 180 Deg F

EDR – 68 Sq FT

Motor – 16 Watts, single phase, 120V, 1550 RPM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 40 00, Drawing M701 & MP-121 - mark 3-EFPF-1

ITEM: AIR FILTER (GASKET SEAL SYSTEM)

Vendor: CAMFIL Model: F39542-1-DWID66943

Salient Characteristics:

Merv Rating – 8

Air Flow – 3500 CFM

APD – INITIAL 0.2 AWG, CHANGE OVER 1 AWG

BAG IN BAG OUT

alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 40 00, Drawing M701 & MP-121 - mark 3-EFFF-1

ITEM: AIR FILTER (GASKET SEAL SYSTEM)

Vendor: CAMFIL Model: F39542-1-DWID66943

Salient Characteristics:

Merv Rating – 17

Air Flow – 3500 CFM

APD – INITIAL 1.6 AWG, CHANGE OVER 2.4 AWG

BAG IN BAG OUT

alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark CD-1

ITEM: AIR DEVICE SUPPLY - DIFFUSER (Aluminum Louvered Face)

Vendor: KRUEGER Model: 51400

Salient Characteristics:

Air Flow – 0 CFM MIN, 100 CFM MAX

Max APD – 0.060 In WG

Mounting - Ceiling

Panel Frame - 12 in x 12 in

Neck Size - 6 in

NC 14

Damper – Radial OBD

Finish - White alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark LFD 1

ITEM: AIR DEVICE SUPPLY - LAMINAR FLOW

Vendor: KRUEGER Model: 5100HF

Salient Characteristics:

Air Flow – 0 CFM MIN, 260 CFM MAX

Max APD – 0.150 In WG

Mounting – Ceiling Recessed

Panel Frame - 24 in x 48 in

Neck Size - 10 in

NC 19

Damper – Cable Operated Butterfly alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark LFD 2

ITEM: AIR DEVICE SUPPLY - LAMINAR FLOW

Vendor: KRUEGER Model: 5100HF

Salient Characteristics:

Air Flow – 220 CFM MIN, 320 CFM MAX

Max APD – 0.290 In WG

Mounting – Ceiling Recessed

Panel Frame - 24 in x 48 in

Neck Size - 12 in

NC 22

Damper – Cable Operated Butterfly alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark SG-1

ITEM: AIR DEVICE SUPPLY - DOUBLE DEFLECTION

Vendor: KRUEGER Model: 5880

Salient Characteristics:

Air Flow – 0 CFM MIN, 180 CFM MAX

Max APD – 0.125 In WG

Mounting – Duct

Panel Frame - 11 in x 9 in

Neck Size – 8 x 6

NC 29

Damper – OBD alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark EG-1

ITEM: AIR DEVICE - RETURN REGISTER

Vendor: KRUEGER Model: S580

Salient Characteristics:

Air Flow – 0 CFM MIN, 120 CFM MAX

Max APD – 0.051 In WG

Mounting – Ceiling

Panel Frame - 12 in x 12 in

Neck Size – 6 in

NC -

Damper – OBD alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark EG-2

ITEM: AIR DEVICE - RETURN REGISTER

Vendor: KRUEGER Model: S580

Salient Characteristics:

Air Flow – 150 CFM MIN, 215 CFM MAX

Max APD – 0.080 In WG

Mounting – Sidewall

Panel Frame - 10 in x 6 in

Neck Size – 10 in x 6 in

NC - 22

Damper – NONE alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-121 - mark EG-3

ITEM: AIR DEVICE - EXHAUST REGISTER

Vendor: KRUEGER Model: S580

Salient Characteristics:

Air Flow – 220 CFM MIN, 300 CFM MAX

Max APD – 0.110 In WG

Mounting – Sidewall

Panel Frame – 12 in x 6 in

Neck Size – 12 in x 6 in

NC - 27

Damper – NONE alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & M-301 - mark 3-TU-1

ITEM: SINGLE DUCT

Vendor: KRUEGER Model: LMHS

Salient Characteristics:

Size 04

Air Flow – 85 CFM MIN, 85 CFM MAX

Control Type - VAV

Control Sequence – 5 Degree Deadband

Reheat Coil – 3.2 MBH, 0.4 GPM, 1 Row, EAT 60 deg F, LAT 90.1 deg F, EWT 160 deg F, LWT 141 deg F, APD 0.01 In H2O, WPD 0.1 Ft H2O alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & M-301 - mark 3-TU-2

ITEM: SINGLE DUCT

Vendor: KRUEGER Model: LMHS

Salient Characteristics:

Size 05

Air Flow – 160 CFM MIN, 160 CFM MAX

Control Type - VAV

Control Sequence – 5 Degree Deadband

Reheat Coil – 7.3 MBH, 0.7 GPM, 2 Rows, EAT 60 deg F, LAT 92.4 deg F, EWT

160 deg F, LWT 138.9 deg F, APD 0.04 In H2O, WPD 0.1 Ft H2O alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-SAV-1

ITEM: AIR FLOW CONTROL VALVE

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 8

Design Air Flow - 255 CFM

Max Air Flow – 255 CFM

APD at Max Air Flow – 0.6 – 3.0 In WG alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-SAV-2

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 10

Design Air Flow - 570 CFM

Max Air Flow – 570 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-SAV-3

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 10

Design Air Flow - 640 CFM

Max Air Flow – 640 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-SAV-4

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 12

Design Air Flow - 860 CFM

Max Air Flow – 860 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-SAV-5

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 12

Design Air Flow - 905 CFM

Max Air Flow – 905 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-1

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 8

Design Air Flow - 215 CFM

Max Air Flow – 215 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-2

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 8

Design Air Flow - 310 CFM

Max Air Flow – 310 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-3

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 8

Design Air Flow - 375 CFM

Max Air Flow – 375 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-4

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 10

Design Air Flow - 400 CFM

Max Air Flow – 400 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-5

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 10

Design Air Flow - 545 CFM

Max Air Flow – 545 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-6

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 12

Design Air Flow - 770 CFM

Max Air Flow – 770 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-7

Vendor: PHOENIX Model: Low-Speed Celeris Valves

Salient Characteristics:

Type - Venturi

Size 12

Design Air Flow - 800 CFM

Max Air Flow – 800 CFM alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 31 00, Drawing M702 & MH-301 – 3-EAV-8

ITEM: AIR FLOW CONTROL VALVE (STAINLESS STEEL)

Vendor: TROX Model: RN100

Salient Characteristics:

Type - Circular

Size 4

Design Air Flow - 70 CFM

Max Air Flow – 70 CFM

APD at Max Air Flow – 0.22 In WG

Control Type - Spring alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Drawing M702

ITEM: PARTICLE COUNTER

Vendor: Lighthouse Model: Apex R3P Remote Particle Counter with Pump

Salient Characteristics:

Minimum Particle Detection – 3 microns

Pump Capacity - 1 CFM

Electrical – 120V, Single Phase, 25 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 23 05 12, Drawing M702 & MP401 – mark 15-CHP-01 & mark 15-CHP-02

ITEM: PUMP

Vendor: Bell & Gossett Model: e-80 1.5x1.5x9.5B

Salient Characteristics:

Type - In-Line

Circulating Fluid – Water, Flow - 75 GPM, Head - 60 FT, Temp – 45 deg F

Min percent Eff – 80%

Electrical – 3HP, 3 phase, 208V, 1750 RPM, Speed Control - VFD alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & EL121 – L1

ITEM: LIGHTING (DIMMABLE CLEAN ROOM GRADE LED TROFFER STEEL HOUSING WITH

GA SKETED DOOR, IMPACT RESISTANT ACRYLIC LENS, 80 CRI, RATED FOR BSL 3 AND 4,

IP66

Vendor: KENALL Model: CSEDO

Salient Characteristics:

Dimensions – 2 ft x 4 ft

LED – 8760 Lumens

Driver 68 Watts

Volts - MVolt

Mounting – Gypsum Ceiling alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & EL121 – L2

GA SKETED DOOR, IMPACT RESISTANT ACRYLIC LENS, 80 CRI, RATED FOR BSL 3 AND 4,

IP66

Vendor: KENALL Model: CSEDO

Salient Characteristics:

Dimensions – 1 ft x 4 ft

LED – 8493 Lumens

Driver 45 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & EL121 – L3

SMOOTH FROSTED 0.187” ACRYLIC LENS, IMPACT RESISTANT ACRYLIC LENS, 80 CRI, IP65

(WATER AND DUST)

Vendor: COOPER Model: FAIL SAFE SERIES

Salient Characteristics:

Dimensions – 2 ft x 4 ft

LED – 4535 Lumens

Driver 48.6 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & EL121 – L4

ITEM: LIGHTING (DIMMABLE CLEAN ROOM GRADE LED TROFFER STEEL HOUSING W/

BATTERY BACKUP GA SKETED DOOR, IMPACT RESISTANT ACRYLIC LENS, 80 CRI, RATED

FOR BSL 3 AND 4, IP66

Vendor: KENALL Model: CSEDO

Salient Characteristics:

Dimensions – 2 ft x 4 ft

LED – 8760 Lumens

Driver 68 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & EL121 – L5

ITEM: LIGHTING (DIMMABLE CLEAN ROOM GRADE LED TROFFER STEEL HOUSING W/

BATTERY BACKUP GA SKETED DOOR, IMPACT RESISTANT ACRYLIC LENS, 80 CRI, RATED

FOR BSL 3 AND 4, IP66

Vendor: KENALL Model: CSEDO

Salient Characteristics:

Dimensions – 1 ft x 4 ft

LED – 8493 Lumens

Driver 45 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & EP131 – W1

ITEM: LIGHTING - ARCHITECTURAL EXTERIOR LED WALL SCONCE FIXTURE WITH

INTEGRAL PHOTOCELL CONTROL

Vendor: KENALL Model: CSEDO

Salient Characteristics:

Dimensions – 8” H x 9” L x 5.5” D

LED – 1978 Lumens

Driver 15 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 26 51 00, Drawing E701 & E501& EP131 – W2

ITEM: LIGHTING – EXTERIOR EQUIPMENT LED UTILITY LIGHT WITH GLASS GUARD

Vendor: HUBBELL Model: VSL-16-30 WHITE OPTIC

Salient Characteristics:

LED – 1625 Lumens

Driver 16 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 10 14 00, Drawing E701 & EL121 – X1

ITEM: LIGHTING – SINGLE FACED SEMI-RECESSED, WALL MOUNTED CLEAN ROOM EXIT

LIGHT WITH BATTERY BACKUP

Vendor: KENELL Model: CMEXR

Salient Characteristics:

LED

Driver 2.5 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________

Reference: Specification Section - 10 14 00, Drawing E701 EP131 – X2

ITEM: LIGHTING – SINGLE FACED WALL MOUNTED EXIT LIGHT WITH BATTERY BACKUP

Vendor: KENELL Model: Millenium Metrx MTSS Series

Salient Characteristics:

LED

Driver 2.5 Watts alternative option for evaluation prior to award as a basis of bid or leave blank if not planning to substitute for the identified equipment in base bid.

BIDDING ON: ____________________________________