UTILITIES DEPARTMENT

REQUEST FOR QUOTES GOODS (RFQ) #RFQ194158A

FOR

RFQ194158A PURCHASE AND DELIVERY/PICKUP OF WATER, GAS AND

WASTEWATER PLUMBING AND PIPELINE SUPPLIES, FITTINGS, VALVES AND

OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

(RFQ) DUE DATE

Wednesday, April 1, 2026 BEFORE 3:00 am

Request for Quotes (RFQ) #RFQ194158A RFQ194158A PURCHASE AND DELIVERY/PICKUP OF WATER, GAS AND WASTEWATER PLUMBING AND PIPELINE SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

TABLE OF CONTENTS

Section 1 Introduction

Section 2 Request for Quotes Summary

Section 3 Instruction to Bidders

Section 4 Specifications

Section 5 Terms and Conditions of Purchase

Section 6 Bid Form

Section 7 Bidder's Questionnaire

Attachments:

A - Insurance Requirements Exhibit-Gen_Revised April 9,2025-Final

B - Special Requirement Qualification Form

Request for Quotes (RFQ) #RFQ194158A

1. INTRODUCTION

1.1. Summary

The City of Palo Alto Utilities Department, Water, Gas, Wastewater Division requests quotations for the purchase and delivery and or pickup of PLUMBING AND PIPELINE SUPPLIES, FITTINGS, VALVE AND OTHER

ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

The City also reserves the right to award to multiple vendors based on the City’s needs per prices quoted.

The City shall award a Blanket Order to the two lowest responsive-responsible bidders of equal value to ensure availability of parts and materials on an as needed basis.

Bidders must Bid on all items listed in the bid forms for all years.

1.2. Background

The City owns and operates all of its own Utilities and is responsible for all maintenance, repairs and replacements required throughout the City. It is imperative we have access to the parts as needed for maintenance, repairs and replacements.

1.3. Contact Information

Renee Howard

Senior Buyer

3201 East Bayshore Road

Palo Alto, CA 94303

Email: renee.howard@paloalto.gov

Phone: (650) 496-5900

Department:

Utilities

1.4. Timeline

RFQ Date February 10, 2026 mailto:renee.howard@paloalto.gov tel:(650)496-5900

Request for Quotes (RFQ) #RFQ194158A 2

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Pre-Bid Conference (Mandatory) March 4, 2026, 9:00am

This will be a virtual meeting but is Mandatory Pre-

Bid

Date and Time: Wednesday March 4, 2026, 9:00

A.M.

Meeting link: Microsoft teams Meeting https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00Yj

I0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?c ontext=%7b%22Tid%22%3a%2268949a6d-ce6e-

4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f

8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d. |

Meeting-Join | Microsoft Teams

Question Submission Deadline March 9, 2026, 1:00pm

Question Response Deadline March 12, 2026, 1:00pm

Quote Submission Deadline April 1, 2026, 3:00am

2. REQUEST FOR QUOTES SUMMARY

2.1. Quote Submittal Information

Bids shall be submitted electronically through the City’s OpenGov portal at:

https://procurement.opengov.com/portal/palo-alto-ca

Bids must be received by no later than 3:00 am on Wednesday, April 1, 2026.

2.2. Addenda/Clarifications/Questions

Should discrepancies be found in this RFQ or should there be a need to clarify this RFQ, Questions/Clarifications must be received by no later than 1:00 pm on Monday, March 9, 2026.

Correspondence shall be communicated through the City’s OpenGov portal within the Q&A tab.

Responses from the City will be communicated through the City’s OpenGov portal to all recipients of this

RFQ via addendum. Inquiries received after the date and time stated may not be accepted. All addenda shall become part of this RFQ and acknowledged through the City’s OpenGov portal. The City shall not be responsible for nor be bound by any oral instructions, interpretations or explanations issued by the

City or its representatives.

https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://teams.microsoft.com/l/meetup-join/19%3ameeting_MWYxYjM3ZmEtMWUzZS00YjI0LWI3YzQtODIwOTY1ZTAwZmIy%40thread.v2/0?context=%7b%22Tid%22%3a%2268949a6d-ce6e-4230-8536-f3e1f8d5dfdd%22%2c%22Oid%22%3a%226542c7f8-ea00-4e2f-8e44-6cda4ad60ab0%22%7d https://procurement.opengov.com/portal/palo-alto-ca

Request for Quotes (RFQ) #RFQ194158A 3

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

3. INSTRUCTION TO BIDDERS

3.1. Submittal

Quotes shall be submitted through the City’s electronic procurement system. A Quote which is attempted to be delivered or which is received after the stated time shall be deemed non-responsive and rejected. The Bidder shall have the sole and exclusive responsibility for ensuring that a quote is received by the time stated herein. Any Bid that is incomplete, unclear, or that fails to fully comply with the applicable requirements set forth herein, including, but not limited to, use of the forms provided by the City, may be rejected as nonresponsive.

3.2. Responsibility of Bidder

A Quote shall be submitted at the sole cost and expense of the Bidder and, in submitting such quote to the City, the Bidder waives any claim or demand against the City which the Bidder may have for any direct or indirect cost or expense of preparing and submitting such Bid.

3.3. Bid Submittals

Bid Form and Bidder’s Documents: Bids must be submitted though the City’s OpenGov portal. Bidder must complete all required items in full and provide signed versions of any documents required in this

RFQ (collectively, the “Bidder’s Documents”). The Bidder will ensure that the information the Bidder inputs into the electronic procurement system matches the information on the Bidder’s Documents it uploads to the electronic procurement system. Any conflict or discrepancy will be resolved as provided in below in "Requirements and Order of Precedence", below, of this Section ("Bid Submittals").

Bidder’s Questionnaire: Each Bid must be accompanied by a completed Bidder’s Questionnaire as provided in this RFQ. Submission of a Bidder’s Questionnaire containing false or incomplete information may be grounds for rejection of the Bid as non-responsive and/or disqualification of the Bidder as not responsible.

Requirements and Order of Precedence: In the event of any conflict or discrepancy between any requirements provided in this RFQ (including but not limited to bid submittal requirements) and any requirements that may be stated in the City’s electronic procurement system, the requirements of this

RFQ will control. In the event of any conflict or discrepancy between information included on (or omitted from) the Bid Form or Bidder’s Documents uploaded to the City’s electronic procurement system and any information inputted into the City’s electronic procurement system, the information included on (or omitted from) the uploaded information or Bidder’s Documents will control. For clarity, the Bidder’s Documents uploaded into the electronic procurement system constitute a Bidder’s Bid, whereas the information a Bidder inputs into the electronic procurement system is for administrative convenience and will not control over the uploaded Bidder’s Documents in event of a conflict or discrepancy.

3.4. Bid Authorization

Any person logging into the electronic procurement system to submit a Bid or any other electronic document required by the City must be authorized by the company or entity being represented, either in a personal or representative capacity, to access and submit such bid documents. If the person does

Request for Quotes (RFQ) #RFQ194158A 4

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

business under his or her own name, that person shall login under his or her own login as authorized by the City’s OpenGov portal. If the person does business under a fictitious business name, that person shall login under his or her own login as authorized by the City's OpenGov portal. If the person logins for and on behalf of a partnership, the person shall do so with his or her authority to sign/login under his or her own login as authorized by the OpenGov.

3.5. Withdrawal of Bid

Prior to the date and time set for the opening of Bids, a Bidder who has submitted a bid and accepted the terms and conditions in the City’s electronic procurement system, may withdraw its bid by selecting

“Unsubmit Bid” at any time before the deadline for the receipt of Bids as specified in the RFQ Summary.

No Bidder may withdraw its Bid for a period of ninety (90) days after the date set for the opening of, subject to applicable California Law and Palo Alto Municipal Code Section 2.30.460(c), whichever occurs first.

3.6. Request(s) for Clarification

Any Bidder may submit a Question or Inquiry to the Question & Answer section of this RFQ for the clarification of any aspect of the Specifications or any other related information, or part thereof, which is a part of the RFQ. Such request shall be submitted electronically via the City’s electronic procurement system Q&A function. Such requests shall be submitted before 1:00 pm on Monday, March 9, 2026. All responses will be made available on the City's OpenGov portal. The City reserves the right to issue an addendum or addenda per the "Addenda" Section of the Instructions to Bidders of the RFQ.

3.7. Addenda

The City reserves the right to issue a written Addendum or Addenda to the electronic solicitation prior to the bid closing date and time. During the Bid process there may be changes to the Contract

Documents, which would require an issuance of an addendum or Addenda. City disclaims any and all liability for loss, or damage to any Bidder who does not receive any addendum issued by City in connection with this RFQ. Any Bidder by submitting a Bid waives any and all claims and demands Bidder may have against City on account of the failure of delivery of any such Addendum to Bidder. Any and all

Addenda issued by City shall be deemed included in this RFQ, and the provisions and instructions therein contained shall be incorporated into any Bid submitted by Bidder.

3.8. Specifications

The specifications included have been prepared to describe the standard quality, and other characteristics needed to meet City requirements. The City has standardized its requirements for The

City of Palo Alto Utilities Department, Water, Wastewater Division requests quotations for the purchase and delivery and or pickup of PLUMBING AND PIPELINE SUPPLIES, FITTINGS, VALVE AND OTHER

ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS. The City shall award a Blanket

Order to the two lowest responsive-responsible bidders of equal value to ensure availability of parts and materials on an as needed basis. and will not accept alternate quotation of a designed material, product, thing, service, “or equal other that specified in the "Specifications" Section of this RFQ.

Request for Quotes (RFQ) #RFQ194158A 5

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

3.9. Pre-Bid Conference

Attendance: This Request for Quote has a Pre-Bid Conference, attendance for this is MANDATORY. For additional information regarding this pre-bid conference, please view this RFQ's Timeline. A BID

SUBMITTED BY A BIDDER WHO FAILS TO ATTEND A MANDATORY PRE-BID CONFERENCE MAY BE

DEEMED NON-RESPONSIVE.

3.10. Electronic Opening

All Bidders and members of the public may view bid results in the electronic procurement system after bid closing. The City reserves the right to change the originally scheduled Bid date and time to a later date and time by issuing an electronic Addendum to that effect. Any and all Bids received by the City before the deadline shall be accepted by the electronic procurement system.

3.11. Contract Award

Subject to the conditions of this RFQ, the City will award the contract, if an award is made, to the lowest responsive and responsible Bidder. In determining whether the Bidder is responsible, the City will use the criteria set forth in Palo Alto Municipal Code Section 2.30.440, as set forth below:

1. To have demonstrated the attribute of trustworthiness, and to have the quality, fitness, capacity, experience, and skill to satisfactorily perform the work, or provide the goods and/or services called for in the invitation for bids;

2. To have the ability to perform the contract within the time specified;

3. To have the equipment, facilities and resources of such capacity and location to enable the bidder to perform the contract;

4. To have the ability to provide, as required, future maintenance, repair, parts and service for the use of goods purchased;

5. To have a record of satisfactory or better performance under prior contracts with the city or others; and

6. To have complied with applicable laws, regulations, policies (including city policies), guidelines and orders governing prior or existing contracts performed by the bidder.

3.12. Determination of Lowest Bid

The lowest bid shall be the lowest total of the bid prices quoted on the Bid Schedule. This total is being used for the purpose of determining the lowest bid.

The lowest Bid shall be the lowest total of the Base Bid prices for Year 1 (Table A) , Year 2 (Table B) and

Year 3 (Table C). Year 2 and Year 3 specifically identify in this RFQ as being used for the purpose of determining the Bid price. For purposes of this section, the Bid for additional years two and three are used for determining the Bid price are Year 2 and Year 3, Bid Tables B and C.

Request for Quotes (RFQ) #RFQ194158A 6

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

3.13. Waiver of Minor Irregularities

The City may exercise its discretion to waive minor irregularities, defects or informalities in the

Bids/Quotes, so long as the waiver would not affect the amount of the Bid or give the Bidder an advantage over others.

3.14. Bid Discrepancies

In the case of a discrepancy between a written amount and the corresponding figures, the written amount shall govern. In the case of a discrepancy between an item price and the corresponding unit price multiplied by the corresponding estimated quantity, the unit price multiplied by the estimated quantity shall govern. In the case of discrepancy between the actual arithmetic total of all items and the total stated by the Bidder, the actual arithmetic total shall govern.

3.15. Award of Contract and Rejection of Bids

Decision to Award

A contract may be awarded to the lowest responsible bidder. The City reserves the right to award more than one Contract with respect to the RFQ.

Decision to Reject

The City reserves the unfettered right to reject all Quotations for any reason or for no reason, to re-advertise an RFQ, or to cancel an RFQ. The City reserves the right to reject as non-responsive any

Quotation which is incomplete, modified, unsigned, or illegible or which is not otherwise submitted in accordance with the requirements of this RFQ.

3.16. Term of Agreement

City intends to issue a Blanket Order to the (2) lowest bidders to for the purchase and delivery and or pickup of Water and Wastewater plumbing and pipeline supplies, fittings, valves, and other accessories and parts for a period of (3) years as required by requesting departments. Approved manufactures are specified in Section 4. Bid form and are the approved manufactures by the City. Quantities are approximate and the total of the bid will be used for the purpose of selecting the lowest responsive and responsible bidders. Due to unforeseen requirements the City may require pricing for items that are not noted on this bid. The term of the pricing agreement shall be effective on the date of award for the initial one-year period. After the initial period, the City reserves the right to exercise up to two (2) additional 12 month extensions for a total of three (3) years.

Subject to:

• Firm fixed price for the initial term of the pricing agreement;

• City Council’s approval of each fiscal year budget and appropriation of funds;

• The Vendor’s compliance with the terms and conditions as established by this RFQ;

• The Vendor’s ability to deliver within the quoted lead time submitted on this solicitation.

• The Vendor’s satisfactory performance, and timely compliance with the requirements of this

RFQ;

Request for Quotes (RFQ) #RFQ194158A 7

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

• Payment terms are Net 30 or greater.

• Notwithstanding the foregoing, City may terminate the agreement, with or without cause, by providing ten (10) days written notice.

• The City reserves the rights to award on an item-by-item basis or aggregate.

• The City also reserves the right to award to multiple vendors based on the City’s needs per prices quoted.

• The City shall award a Blanket Order to the two lowest responsive-responsible bidders of equal value to ensure availability of parts and materials on an as needed basis.

3.17. Certification of Nondiscrimination

By submitting a quotation, the Bidder certifies that: in the performance of the Contract, if awarded, it shall not discriminate in the employment of any person due to the race, skin color, gender, gender identity, age, religion, disability, national origin, ancestry, sexual orientation, pregnancy, genetic information or condition, housing status, marital status, familial status, weight or height of such person;

and further certifies that it is in compliance with all Federal, State and local laws, regulations, rules, directives and executive orders regarding nondiscrimination in employment

3.18. F.O.B. Point

Prices shall be F.O.B. Destination, Freight Prepaid. Price shall include all applicable transportation and delivery charges. Standard Shipment via UPS or Local Freight carrier is acceptable.

3.19. Delivery Requirements

When delivery time is requested in the quote or bid documents, time shall be of the essence; therefore, the quote or bid shall include the delivery date. In some instances, the City may specify only a maximum number of days for delivery and will use this delivery date as part the criteria to determine the award.

The purchase order to be awarded is for a specific quantity purchased at one time. Delivery requirements are as specified in the "Specifications" Section of this RFQ.

3.20. Rights of the City of Palo Alto

This RFQ does not commit the City to enter into a contract, nor does it obligate the City to pay for any costs incurred in preparation and submission of quotation or in anticipation of a contract.

3.21. Exceptions

To the specifications, data specifications sheet or requirements issued must be itemized and justified in writing and included with proposals or quotations submitted.

3.22. Documentation

Manuals, Data Specifications sheet when applicable, shall be furnished by the Vendor with the shipment or under separate cover.

Request for Quotes (RFQ) #RFQ194158A 8

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

3.23. Taxes

Quotations shall include all applicable federal, state and local taxes, import duties, commissions or other charges.

4. SPECIFICATIONS

4.1. See Section 4. Bid Forms

The City shall award a Blanket Order to the two lowest responsive-responsible bidders of equal value to ensure availability of parts and materials on an as needed basis.

Bidders must Bid on all items listed in the bid forms for all years.

5. TERMS AND CONDITIONS OF PURCHASE

5.1. Acceptance / Agreement

City of Palo Alto (City) reserves the right to reject any and all quotations, to waive any informalities, and, unless otherwise specified by Seller, to accept any item in a quotation. By accepting or filing this

Purchase Order (P.O.), Seller agrees to the terms and conditions herein which shall prevail over any inconsistent provision in any form or other paper submitted by Seller. All shipments or services performed shall be deemed to have been made pursuant hereto. No other terms are acceptable. This

P.O., including all specifications and drawings, shall constitute the entire agreement between the parties unless modified in writing by City.

5.2. City's Property

Seller agrees that the information, tools, jigs, dies, or materials, and drawings, patterns, and specification supplied or paid for by City shall be and remain City property and shall be held by Seller for

City unless directed otherwise. Seller shall account for such items and keep them protected, insured, and in good working conditions without expense to City.

5.3. Delivery

The terms of delivery are as stated on the reverse side hereof. The obligation of Seller to meet the delivery dates, specifications, and quantities set forth herein is of the essence of this P.O. No boxing, packing, or cartage charge will be allowed unless authorized by this P.O. Deliveries are to be made both in quantities and at times specified herein or, if not, such quantities and times are specified pursuant to

City’s written instruction. Items not delivered may be canceled without penalty to City. Shipments in greater or lesser quantity that ordered may be returned at Seller’s expense unless written authorization is issued by City.

Request for Quotes (RFQ) #RFQ194158A 9

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

5.4. Prices

The price which Seller charges in filling this P.O. shall not be higher than Seller’s most recent quote or charge to City for such materials, supplies, services and/or installations unless City expressly agrees otherwise in writing. Notwithstanding the prices set forth the P.O. City shall receive the benefit of any general reduction in the price of any item(s) listed herein which may be made by Seller at any time prior to the last delivery of goods or services covered by this P.O.

5.5. Termination

City shall have the right to terminate this P.O. or any part thereof upon ten (10) days notice in writing to

Seller.

(1) Without Cause. City may terminate all or any part of this P.O. without cause. Any claim by Seller for damages due to termination without cause must be submitted to City within thirty (30) days after effective date of termination.

(2) For Cause. If Seller fails to make any delivery in accordance with the agreed delivery date, delivery schedule, or otherwise fails to observe or comply with any of the other instructions, terms, conditions or warranties applicable to this P.O., City may, in addition to any other right or remedy provided by this

P.O. or by law, terminate all or any part of this P.O. in writing without any liability of City with respect to

Seller at any time during the term of this P.O. In the event of termination for cause, City may purchase supplies or services elsewhere on such terms or in such manner as City may deem appropriate and Seller shall be liable to City for any cost and other expenses incurred by City, which is charged to City.

5.6. Changes

City shall have the right at any time by written notice via P.O. Change Order to Seller to make changes in the specifications, the quantity of items called for, delivery schedules, and requirements covering testing, packaging, or destination. Any claim by Seller for adjustment under this clause shall be deemed waived unless made in writing with then (10) days after receipt by Seller of notice of such change. Price increases or extensions of time for delivery shall not be binding on City unless evidenced by a P.O.

Change Order issued by City’s Purchasing Manager.

5.7. Inspection

City shall have the right to inspect and approve or reject any materials, supplies, services and/or installations upon arrival of notice of completion prior to payment without regard to the manner of shipment, completion, or any shipping or price terms contained in this P.O. All materials, supplies, services and/or installations must be furnished as specified.

(1) Defective, damaged, and nonconforming materials and/or supplies may be returned for credit or refund, at Seller’s expense. City may charge Seller for all expenses of unpacking, examining, repacking and reshipping of such materials and/or supplies.

(2) Defective, incorrect and nonconforming services and/or installations may be returned for credit or refund, at Seller’s expense. All of the above notwithstanding prior payment by City

(3) City may waive defects that exist.

Request for Quotes (RFQ) #RFQ194158A 10

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

5.8. Warranty

Seller expressly warrants that all materials, supplies, services and/or installations covered by this P.O.

shall:

(1) conform to the specifications, drawings, samples, or other descriptions specified by City or if none are so specified, to Seller’s standard specification or the standards of the ASTM or ANSI or other national standard organizations;

(2) be new and unless specified to the contrary on the face hereof, will be free from defects in material and workmanship and will be free of all liens and encumbrances and will conform to any affirmation of facts made on the container or label;

(3) be adequately contained, packaged, marked, labeled and/or provided in compliance with all applicable federal and state laws and regulations (including materials deemed hazardous);

(4) be performed within the rules and regulations of the Occupational Safety and Health Act of 1970 (as amended);

(5) be produced or transferred or disposed of as required by federal and state laws and regulation under the conditions of the Toxic Substances Control Act; the Hazardous Materials Control and Hazardous

Waste Regulations; and other toxic laws and programs.

Seller further expressly agrees to protect, indemnify, and hold harmless City, its employees and agents for any loss, damage, fine, liability, fee (including reasonable charges and fees) or expense arising in connection with or resulting from Seller’s failure to furnish materials or supplies or perform services that conform with any warranty contained herein.

(6) have good marketable title.

5.9. Governing Law

This P.O. shall be governed by the laws of the State of California.

5.10. Independent Contractor, Insurance

Seller certifies, by acceptance, that he/she is an independent contractor. Seller shall protect, defend, and indemnify and hold City harmless against all damages, liability, claims, losses and expenses

(including attorney’s fees) arising out of , or resulting in any way from Seller’s negligence in providing the goods or services purchased hereunder or from any act or omission of Seller, its agents, employees, or subcontractors, Seller shall maintain such public liability insurance, including contractual liability, automobile and general public liability, (including non-owned automobile liability) Worker’s

Compensation, and employer’s liability insurance as well adequately protect City against such damage, liabilities, claims, losses, and expenses (including attorney’s fees). Seller agrees to submit certificates of insurance, evidencing its insurance coverage when requested by City.

5.11. Equal Opportunity Clause

By acceptance of this P.O., Seller certifies it is in compliance with the Equal Opportunity Clause required by Executive Order 11246, as amended, and the Palo Alto Municipal Code, as amended, including

Affirmative Action Compliance Programs for Veterans; Handicapped; and Minority Business, and other equal opportunity programs.

Request for Quotes (RFQ) #RFQ194158A 11

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

5.12. Force Majeure

City may delay delivery or acceptance occasioned by causes beyond its control. Seller shall hold such materials, supplies, services and or installations at the direction of City and shall deliver them when the cause affecting the delay has been removed. City shall be responsible only for Seller’s direct additional costs in holding the goods or delaying performance of this P.O. and City’s request. Seller shall also be excused if delivery is delayed by unforeseen events beyond its reasonable control, provided Seller notifies City as soon as they occur. City may cancel this P.O. if such delay exceeds thirty (30) days from the original delivery date. Seller shall use its best efforts to grant preference to this P.O. over those of other customers, which were placed after this P.O.

5.13. Authority of Agent or Factor

Seller represents that, whenever it executes this P.O. on behalf of a third party as an agent or factor, it shall disclose the existence of the agency or factor relationship to City. Seller shall be deemed to have the legal authority to enter into this P.O. with City on behalf of the third party.

5.14. Interpretation of Contract Documents

In the event of a conflict between the terms of this P.O. and the attached specification with respect to any obligation of Seller, the provision which impose the greater obligations upon Seller shall prevail.

5.15. Environmentally Preferred Purchasing Requirements

(1) Hazardous Waste:

Seller shall take-back all spent or otherwise discarded hazardous products sold to the City by the Seller if the spent or discarded products are classified as hazardous or universal wastes by State or Federal regulations. Seller shall provide convenient collection and recycling services (or disposal services if recycling technology is unavailable) for all universal wastes, which originate from the Vendor. Hazardous waste manifests or bills of lading must be provided to City staff upon request. Recycling and reuse of hazardous wastes must occur within the United States. Universal waste lists and information are available www.dtsc.ca.gov/HazardousWaste/UniversalWaste/. A hazardous waste list is available at http://www.calrecycle.ca.gov/LEA/Training/wasteclass/yep.htm. Additional information can be obtained by contacting the City of Palo Alto Hazardous Waste Department at (650) 496-6980.

(2) Zero Waste and Pollution Prevention:

Per Palo Alto City Council policy, the City is targeting to achieve Zero Waste by 2021. The City must also meet Municipal Regional Stormwater Permit requirements requiring no visible impact from litter via stormdrains by 2022. To that end the vendor, manufacturer and or contractor must individually or collaboratively comply with the waste reduction, reuse and recycling requirements of the City’s Zero

Waste and Pollution Prevention Programs. Seller acknowledges and agrees that if Seller fails to fully and satisfactorily comply with these requirements, the City will suffer, as a result of Seller’s failure, substantial damages which are both extremely difficult and impracticable to ascertain. Therefore, the

Seller agrees that in addition to all other damages to which the City may be entitled, in the event Seller fails to comply with the below requirements Seller shall pay City as liquidated damages the amounts specified below. The liquidated damage amount is not a penalty but considered to be a reasonable estimate of the amount of damages City will suffer as a result of such non-compliance.

https://www.dtsc.ca.gov/HazardousWaste/UniversalWaste/ http://www.calrecycle.ca.gov/LEA/Training/wasteclass/yep.htm

Request for Quotes (RFQ) #RFQ194158A 12

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

• Sellers shall adhere to the standard that all printed materials provided to the City that are generated from a personal computer and printer including, proposals, quotes, invoices, reports, and public education materials shall be double-sided, printed on a minimum of 30% post-consumer content paper or greater unless otherwise approved by the City’s Environmental

Services Division (650) 329-2117. Materials printed by a professional printing company shall be a minimum of 30% post-consumer material or greater and printed with vegetable based inks.

Liquidated damages of $30 per document will be assessed by City for failure to adhere to this requirement;

• All paper packaging must be Forest Stewardship Council (FSC) Certified.

• All primary, secondary and shipping (tertiary) packaging be minimized to the maximum extent feasible while protecting the product being shipped;

• All primary, secondary and shipping packaging shall be recyclable in the City’s recycling program.

A complete list of items accepted for recycling are found at www.zerowastepaloalto.org or by calling (650) 496-5910. If any portion is received that does not meet this requirement, liquidated damages of $235 or a minimum of $50 if the combined product and shipping cost is $235 or less will be assessed by City for failure to adhere to this requirement.

• Expanded foam plastics (e.g., foam or cushion blocks, trays, packing “peanuts”), such as but not limited to polystyrene (aka Styrofoam™), polypropylene, or polyurethane shall not be used as primary, secondary or tertiary/shipping packaging with the following exceptions:

o Primary packaging made from these materials may be used if the vendor, manufacturer, contractor individually or collaboratively does one of the following:

▪ takes the material back at the City’s convenience and at no cost to the City, or

▪ pays the City of Palo Alto’s disposal costs via payment of liquidated damages of $235, or a minimum of $50 if the combined product and shipping cost is $235 or less;

o Bioplastics that meet ASTM D6400 standards for compostability may be accepted with approval from the City’s Environmental Services Division subject to local municipal compost facility requirements;

o if approved by the City’s Environmental Services Division, a packaging requirement may be waived if no other viable packaging alternative exists;

• Reusable/returnable pallets shall be used and taken back by the Seller, at no additional cost to the City. Seller shall provide documentation upon request ensuring reuse of pallets and/or recycling of broken pallets. Liquidated damages of $262 or a minimum of $50 if the combined product and shipping cost is $262 or less will be assessed by City for failure to adhere to this requirement.

(3) Energy and Water Efficiency:

Seller shall provide products with an ENERGY STAR, Water Sense or State of California standard rating, whichever is more efficient, when ratings exist for those products. A life cycle cost analysis shall be https://www.zerowastepaloalto.org/

Request for Quotes (RFQ) #RFQ194158A 13

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

provided to the City upon request and shall at minimum include: first cost, operating costs, maintenance costs, and disposal costs.

Contacts for additional information about City of Palo Alto

Hazardous Waste, Zero Waste and Utilities programs:

Hazardous Waste Program (Public Works)

(650) 496-6980

Zero Waste Program (Public Works)

(650) 496-5910

Watershed Protection

(650) 329-2117

Energy Efficiency

(650) 496-2244

(4) Liquidated Damages:

Seller agrees that failure to comply with the City’s Environmentally Preferred Purchasing Requirements will result in Liquidated Damages, according to the table marked Liquidated Damages on page 3 of this

P.O.

5.16. Noncompliance With Environmentally Preferred Purchasing Requirements, Liquidated Damages

The following table lists the events that constitute breaches of the Agreement’s standard of performance warranting the imposition of liquidated damages; the acceptable performance level, and the amount of liquidated damages for failure to meet the contractually required standards of performance.

Event of Non-Performance Acceptable

Performance

Level

(Allowed events per Fiscal Year)

Liquidated Damage

Amount

Recycled Paper Use

Failure to use 30% recycled content paper

1 $30 per each document

Request for Quotes (RFQ) #RFQ194158A 14

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Recyclable Packaging Materials

Failure of Seller to Use secondary and shipping packaging that is recyclable in the City's recycling program.

1 $235 or a minimum of $50 if the combined product and shipping cost is

$250 or less will be incurred if this is not adhered to.

Expanded Foam Plastics

Unapproved use of expanded foam plastics for secondary or shipping packaging.

0 $235 or a minimum of $50 if the combined product and shipping cost is

$235 or less

Pallet use

Failure of Seller to take-back and reuse pallets, recycling only broken pallets, at no additional cost to the

City

1 $262 or a minimum of $50 if the combined product and shipping cost is

$2 or less

6. BID FORM

Complete the following line items as part of your electronic submittal. All quotations must be submitted for each line item identified on this form.

QUANTITIES

Quantities as specified are approximate and no guarantee is implied that the exact amount will be purchased.

DELIVERY:

Delivery terms shall be F.O.B. Palo Alto, Freight Prepaid in accordance with the supplied "Terms and

Conditions of Purchase".

TABLE A MISCELLANEOUS WATER PARTS (YEAR 1)

Request for Quotes (RFQ) #RFQ194158A 15

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City Approved Preferred

Manufacturer Quantity Unit of

Measure Unit Cost Total

Extended

Price

Lead time Quoted

Manufacture

Part Number

1 2” x 1” Brass Bushing No Lead (Muller or

Ford) 10 ea

2 1” Brass 90deg No Lead (Muller or Ford) 10 ea

3 8” x 4” Flange Tee C110 IMP (Sigma) 5 ea

4 8” x 6” Flange Tee C110 IMP (Sigma) 5 ea

5 8” Blind Flange DI IMP (Sigma) 10 ea

6 1” Brass Tee No Lead (Mueller or Ford) 10 ea

7 1” x 3” Brass Nipple No Lead (Mueller or

Ford) 10 ea

8 1” x 6” Brass Nipple No Lead (Mueller or

Ford) 10 ea

9 1” x 3/4” Brass Nipple No Lead (Mueller or

Ford) 10 ea

10 6” x 2” MJ Tapped Cap C153 IMP (SIGMA) 4 ea

11 6” x 36” Cast Iron MJ Bury 6 Bolt (SIGMA) 5 ea

12 6” x 42” Cast Iron MJ Bury 6 Bolt (SIGMA) 5 ea

13 6” x 48” Cast Iron MJ Bury 6 Bolt (SIGMA) 5 ea

14 4” x 2” SDR11 IPS HDPE Tee Molded

(Integrity Fusion Products, Inc.)

10 ea

15 1” x 6” Repair Clamp Full Circle 1.13 OD

(Smith Blair) 20 ea

16 ¾” x 6” Repair Clamp Full Circle 1.05 OD

(Smith Blair) 10 ea

17 ¾” x 6” Repair Clamp Full Circle 0.88 OD

(Smith Blair) 10 ea

18 6” x 4” Stainless Steel (SS) Tapping Sleeve

6.83 -7.16 OD (JCM)

10 ea

19 6” x 4” Stainless Steel (SS) Tapping Sleeve

6.83 -7.16 OD (JCM)

10 ea

20 8” x 4” SS Tap Sleeve, 9.27-9.69 OD (JCM) 10 ea

Request for Quotes (RFQ) #RFQ194158A 16

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City Approved Preferred

Manufacturer Quantity Unit of

Measure Unit Cost Total

Extended

Price

Lead time Quoted

Manufacture

Part Number

21 10 x 8in SS Tapping Sleeve (JCM) 5 ea

22 4” C-900 Class 150 (Vinylteck) 200 ft

23 6” C-900 Pipe Class 150 (Vinylteck) 200 ft

24 8” C-900 Pipe, Class 150 (Vinylteck) 200 ft

25 6” x 8” 6 Hole x 8 Hole Breakaway Spool

(SIGMA)

5 ea

26 6” x 12” 6 Hole x 6 Hole Breakaway Spool

(SIGMA)

5 ea

27 6” x 18” 6 Hole x 6 Hole Breakaway Spool

(SIGMA)

2 ea

28 8” x 1” Double Bronze Strap Saddle

(Mueller) 5 ea

29 6” x 2” Double Bronze Strap Saddle

(Mueller) 10 ea

30 8” x 2” Double Bronze Strap Saddle

(Mueller)

TOTAL

TABLE B: MICELLANEOUS WASTEWATER PARTS (YEAR 1)

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

1 6x4in, Clay, Band Seal

Wye (Mission Rubber

Company)

5 ea

2 8x4in, Clay, Band Seal

Wye (Mission Rubber

Company)

5 ea

3 6” SDR17 IPS Molded

Lateral Wye (Integrity

Fusion Products, Inc.)

Request for Quotes (RFQ) #RFQ194158A 17

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

4 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR51 44 ARC (Mission

Rubber Company)

4 ea

5 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR56 44 ARC (Mission

Rubber Company)

4 ea

6 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR01 88 ARC (Mission

Rubber Company)

2 ea

7 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR01 1010 ARC

(Mission Rubber

Company)

2 ea

8 45deg Elbow 4” IPS

SDR17 (AGRU)

2 ea

9 45 deg Elbow 6" IPS

SDR17 (AGRU)

10 ea

10 6” SDR17 HDPE Pipe

(Performance Pipe

DriscoPlex 4100)

200 ft

11 4" SDR17 WYE

(Integrity Fusion

Products, Inc.)

2 ft

12 6" SDR17 WYE

(Integrity Fusion

Products, Inc.)

10 ft

13 4" T-cone plug (ETCO

Specialty Products, Inc.)

2 ft

Request for Quotes (RFQ) #RFQ194158A 18

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

14 6” T-cone Plug (ETCO

Specialty Products, Inc.)

10 ft

TABLE C: OTHER FEES (YEAR 1)

Line Item Description Quantity Unit of

Measure Unit Cost Total

1 Delivery Fee 1 ea

2 Pick Up In Store Fee 1 ea

3 Rush/Same Day Delivery Fee 1 ea

4 Restocking Fee 1 ea

5 After Hours Access Fee 1 ea

TABLE A: MISCELLANEOUS WATER PARTS (YEAR 2)

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

1 2” x 1” Brass Bushing

No Lead (Muller or

Ford)

10 ea

2 1” Brass 90deg No Lead

(Muller or Ford) 10 ea

3 8” x 4” Flange Tee C110

IMP (Sigma) 5 ea

4 8” x 6” Flange Tee C110

IMP (Sigma) 5 ea

Request for Quotes (RFQ) #RFQ194158A 19

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

5 8” Blind Flange DI IMP

(Sigma) 10 ea

6 1” Brass Tee No Lead

(Mueller or Ford) 10 ea

7 1” x 3” Brass Nipple No

Lead (Mueller or Ford) 10 ea

8 1” x 6” Brass Nipple No

Lead (Mueller or Ford) 10 ea

9 1” x 3/4” Brass Nipple

No Lead (Mueller or

Ford)

10 ea

10 6” x 2” MJ Tapped Cap

C153 IMP (SIGMA)

4 ea

11 6” x 36” Cast Iron MJ

Bury 6 Bolt (SIGMA) 5 ea

12 6” x 42” Cast Iron MJ

Bury 6 Bolt (SIGMA) 5 ea

13 6” x 48” Cast Iron MJ

Bury 6 Bolt (SIGMA) 5 ea

14 4” x 2” SDR11 IPS HDPE

Tee Molded (Integrity

Fusion Products, Inc.)

10 ea

15 1” x 6” Repair Clamp

Full Circle 1.13 OD

(Smith Blair)

20 ea

16 ¾” x 6” Repair Clamp

Full Circle 1.05 OD

(Smith Blair)

10 ea

17 ¾” x 6” Repair Clamp

Full Circle 0.88 OD

(Smith Blair)

Request for Quotes (RFQ) #RFQ194158A 20

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

18 6” x 4” Stainless Steel

(SS) Tapping Sleeve

6.83 -7.16 OD (JCM)

10 ea

19 6” x 4” Stainless Steel

(SS) Tapping Sleeve

6.83 -7.16 OD (JCM)

10 ea

20 8” x 4” SS Tap Sleeve, 9.27-9.69 OD (JCM)

10 ea

21 10 x 8in SS Tapping

Sleeve (JCM) 5 ea

22 4” C-900 Class 150

(Vinylteck) 200 ft

23 6” C-900 Pipe Class 150

(Vinylteck) 200 ft

24 8” C-900 Pipe, Class

150 (Vinylteck) 200 ft

25 6” x 8” 6 Hole x 8 Hole

Breakaway Spool

(SIGMA)

5 ea

26 6” x 12” 6 Hole x 6 Hole

Breakaway Spool

(SIGMA)

5 ea

27 6” x 18” 6 Hole x 6 Hole

Breakaway Spool

(SIGMA)

2 ea

28 8” x 1” Double Bronze

Strap Saddle (Mueller) 5 ea

29 6” x 2” Double Bronze

Strap Saddle (Mueller) 10 ea

30 8” x 2” Double Bronze

Strap Saddle (Mueller)

Request for Quotes (RFQ) #RFQ194158A 21

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

TABLE B: MICELLANEOUS WASTEWATER PARTS (YEAR 2)

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

1 6x4in, Clay, Band Seal

Wye (Mission Rubber

Company)

5 ea

2 8x4in, Clay, Band Seal

Wye (Mission Rubber

Company)

5 ea

3 6” SDR17 IPS Molded

Lateral Wye (Integrity

Fusion Products, Inc.)

10 ea

4 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR51 44 ARC (Mission

Rubber Company)

4 ea

5 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR56 44 ARC (Mission

Rubber Company)

4 ea

6 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR01 88 ARC (Mission

Rubber Company)

2 ea

7 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR01 1010 ARC

(Mission Rubber

Company)

2 ea

8 45deg Elbow 4” IPS

SDR17 (AGRU)

2 ea

9 45 deg Elbow 6" IPS

SDR17 (AGRU)

Request for Quotes (RFQ) #RFQ194158A 22

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

10 6” SDR17 HDPE Pipe

(Performance Pipe

DriscoPlex 4100)

200 ft

11 4" SDR17 WYE

(Integrity Fusion

Products, Inc.)

2 ft

12 6" SDR17 WYE

(Integrity Fusion

Products, Inc.)

10 ft

13 4" T-cone plug (ETCO

Specialty Products, Inc.)

2 ft

14 6” T-cone Plug (ETCO

Specialty Products, Inc.)

TABLE C: OTHER FEES (YEAR 2)

Line Item Description Quantity Unit of

Measure Unit Cost Total

1 Delivery Fee 1 ea

2 Pick Up In Store Fee 1 ea

3 Rush/Same Day Delivery Fee 1 ea

4 Restocking Fee 1 ea

TABLE A: MISCELLANEOUS WATER PARTS (YEAR 3)

Request for Quotes (RFQ) #RFQ194158A 23

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

1 2” x 1” Brass Bushing

No Lead (Muller or

Ford)

10 ea

2 1” Brass 90deg No Lead

(Muller or Ford) 10 ea

3 8” x 4” Flange Tee C110

IMP (Sigma) 5 ea

4 8” x 6” Flange Tee C110

IMP (Sigma) 5 ea

5 8” Blind Flange DI IMP

(Sigma) 10 ea

6 1” Brass Tee No Lead

(Mueller or Ford) 10 ea

7 1” x 3” Brass Nipple No

Lead (Mueller or Ford) 10 ea

8 1” x 6” Brass Nipple No

Lead (Mueller or Ford) 10 ea

9 1” x 3/4” Brass Nipple

No Lead (Mueller or

Ford)

10 ea

10 6” x 2” MJ Tapped Cap

C153 IMP (SIGMA)

4 ea

11 6” x 36” Cast Iron MJ

Bury 6 Bolt (SIGMA) 5 ea

12 6” x 42” Cast Iron MJ

Bury 6 Bolt (SIGMA) 5 ea

13 6” x 48” Cast Iron MJ

Bury 6 Bolt (SIGMA) 5 ea

14 4” x 2” SDR11 IPS HDPE

Tee Molded (Integrity

Fusion Products, Inc.)

Request for Quotes (RFQ) #RFQ194158A 24

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

15 1” x 6” Repair Clamp

Full Circle 1.13 OD

(Smith Blair)

20 ea

16 ¾” x 6” Repair Clamp

Full Circle 1.05 OD

(Smith Blair)

10 ea

17 ¾” x 6” Repair Clamp

Full Circle 0.88 OD

(Smith Blair)

10 ea

18 6” x 4” Stainless Steel

(SS) Tapping Sleeve

6.83 -7.16 OD (JCM)

10 ea

19 6” x 4” Stainless Steel

(SS) Tapping Sleeve

6.83 -7.16 OD (JCM)

10 ea

20 8” x 4” SS Tap Sleeve, 9.27-9.69 OD (JCM)

10 ea

21 10 x 8in SS Tapping

Sleeve (JCM) 5 ea

22 4” C-900 Class 150

(Vinylteck) 200 ft

23 6” C-900 Pipe Class 150

(Vinylteck) 200 ft

24 8” C-900 Pipe, Class

150 (Vinylteck) 200 ft

25 6” x 8” 6 Hole x 8 Hole

Breakaway Spool

(SIGMA)

5 ea

26 6” x 12” 6 Hole x 6 Hole

Breakaway Spool

(SIGMA)

5 ea

27 6” x 18” 6 Hole x 6 Hole

Breakaway Spool

(SIGMA)

2 ea

Request for Quotes (RFQ) #RFQ194158A 25

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

28 8” x 1” Double Bronze

Strap Saddle (Mueller) 5 ea

29 6” x 2” Double Bronze

Strap Saddle (Mueller) 10 ea

30 8” x 2” Double Bronze

Strap Saddle (Mueller)

TABLE B: MICELLANEOUS WASTEWATER PARTS (YEAR 3)

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

1 6x4in, Clay, Band Seal

Wye (Mission Rubber

Company)

5 ea

2 8x4in, Clay, Band Seal

Wye (Mission Rubber

Company)

5 ea

3 6” SDR17 IPS Molded

Lateral Wye (Integrity

Fusion Products, Inc.)

10 ea

4 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR51 44 ARC (Mission

Rubber Company)

4 ea

5 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR56 44 ARC (Mission

Rubber Company)

4 ea

Request for Quotes (RFQ) #RFQ194158A 26

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description / City

Approved Preferred

Manufacturer

Quantity Unit of

Measure Unit Cost Total

Extended

Price

Quoted

Manufacture

Part Number

6 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR01 88 ARC (Mission

Rubber Company)

2 ea

7 Flex-Seal ARC Shielded

Adjustable Sewer

Repair Couplings –

MR01 1010 ARC

(Mission Rubber

Company)

2 ea

8 45deg Elbow 4” IPS

SDR17 (AGRU)

2 ea

9 45 deg Elbow 6" IPS

SDR17 (AGRU)

10 ea

10 6” SDR17 HDPE Pipe

(Performance Pipe

DriscoPlex 4100)

200 ft

11 4" SDR17 WYE

(Integrity Fusion

Products, Inc.)

2 ft

12 6" SDR17 WYE

(Integrity Fusion

Products, Inc.)

10 ft

13 4" T-cone plug (ETCO

Specialty Products, Inc.)

2 ft

14 6” T-cone Plug (ETCO

Specialty Products, Inc.)

TABLE C: OTHER FEES (YEAR 3)

Request for Quotes (RFQ) #RFQ194158A 27

SUPPLIES, FITTINGS, VALVES AND OTHER ACCESORIES AND PARTS ON AN AS NEEDED BASIS FOR UP TO 3 YEARS.

Line Item Description Quantity…