RFQ_-_Blue_Woods_Creek_Reconstruction_Design.docx
DOCX document 180 KB Posted
- Solicitation number
- 2026-GEN-00113
- Issued by
- Hamilton County, Indiana
About this file
Summary of Request for Qualifications
This document is a Request for Qualifications issued by the Hamilton County Drainage Board in Indiana for professional engineering services to design the reconstruction of portions of the Moffitt and Williamson Regulated Drain, commonly known as Blue Woods Creek. The Board seeks qualified engineering firms with expertise in hydraulic modeling, permitting, design, and construction documentation for stormwater conveyance channels. The scope of work encompasses general project management, wetland assessment and delineation, tree inventory, geotechnical investigation, drain alignment evaluation, surveying, hydraulic and hydrologic modeling, environmental design, opinion of probable cost development, construction plan and specification development, permitting, bidding assistance, construction phase services, as-built documentation, and long-term mitigation monitoring. The RFQ was issued November 16, 2026, with a submission deadline of December 7, 2026, at 12:00 PM ET at the Hamilton County Drainage Board meeting. Following SOQ submission, the evaluation committee will immediately begin review and scoring, with the Board selecting the three most highly qualified consultants for notification of final ranking. The term of the resulting contract will extend through project completion, including construction phase services and as-built submittals.
The evaluation will utilize a qualifications-based selection method consistent with 2 CFR 200.320(b)(2)(iv), with pricing explicitly prohibited as an evaluation criterion. Scoring is weighted across five criteria: Past Performance (25 points), Permitting Agency Hydraulic Modeling Experience (25 points), Consultant's Qualifications and Relevant Experience (20 points), Project Understanding and Approach (15 points), and Capacity and Availability of Team (15 points). Prior to cost negotiations with the highest-ranked consultant, the Board will prepare an independent cost estimate and conduct negotiations under either a Cost Plus Fixed Fee or Cost Reimbursement contract structure. The project may qualify for reimbursement through the Federal Emergency Management Agency Public Assistance program and must comply with all applicable federal, state, and local statutes and guidelines. All work must conform to U.S. Customary units and the standards of the Hamilton County Surveyor's Office, including specific requirements for survey standards, construction plan standards, and as-built submittal standards. Consultants must comply with federal contract provisions detailed in Exhibit A, including requirements related to debarment, equal employment opportunity, Davis-Bacon Act compliance, clean air and water standards, and prohibitions on covered telecommunications equipment.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Exhibit_F.pdf | ||
| Notice_to_Contractors_-_RFQ_Blue_Woods_Creek_Design.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Request for Qualifications for Professional Services Hamilton County, Indiana
1. Introduction The Hamilton County Drainage Board (the “Board”) invites Statements of Qualifications (“SOQ”) from qualified Engineering firms (“Consultant”) to provide professional services for the reconstruction of a portion of the Asa Williamson Extension Arm of the Moffitt and Williamson Regulated Drain and a portion of the Martin Marietta Materials Relocation Arm of the Moffitt and Williamson Regulated Drain (“Drain”), commonly known as Blue Woods Creek (“Project”).
This RFQ will use a qualifications-based selection method that is consistent with 2 CFR § 200.320(b)(2)(iv).
For purposes of this RFQ, the terms RFQ and SOQ are used interchangeably and have the same meaning; however, for clarity, this document will refer to them as “RFQ” and “SOQ.”
This Project may qualify for reimbursement through the Federal Emergency Management Agency Public Assistance program.
The Board reserves the right to issue addenda modifying this RFQ, or to withdraw the RFQ, at any time, for any reason.
2. Project Description The Board requests RFQ’s from Consultants experienced in the modelling, permitting, design, development of construction drawings and bidding documents of channels that convey stormwater runoff to provide professional services for the re-establishment of the Drain. The limits of the Project are indicated on Exhibit “F”.
This Project may qualify for reimbursement through the Federal Emergency Management Agency Public Assistance program and must conform to all applicable local, state, and federal statutes and guidelines.
3. Scope of Consultant Services The selected Consultant shall provide all professional services necessary to re-establish the Drain.
All services shall be performed using U.S. Customary (English) units and shall conform to the standards of the Hamilton County Surveyor’s Office regarding design, documentation, and submittal requirements.
Consultant shall have a proven history of hydraulic modeling for federal and state regulatory agency compliance.
Consultant shall have a proven history of designing and permitting waterway construction and/or waterway restoration projects.
Consultant shall conform to U.S. Army Corps of Engineers Engineer Research and Development Center Regional Supplement to the Corps of Engineers Wetland Delineation Manual: Midwest Region (Version 2.0) (ERDC/EL TR010-16) dated August 2010 or latest version in assessing the area of the Project for the presence of wetlands.
Consultant shall provide a written report of the assessment of wetlands within the project area and the factors considered in determining the presence of wetlands within the project area. The format of the report and the data presented in the report shall conform to accepted industry standards for such a report. The report will be used by the Board in discussions with the U.S. Army Corps of Engineers and/or the Indiana Department of Environmental Management regarding wetlands within the project area and possibly attached to any required permit applications. The report shall include the latitude and longitude coordinates of all flagging placed in the field.
Consultant shall conform to the Hamilton County Survey Standards when performing any field or other surveying services. [Attached hereto as Exhibit “B” and incorporated fully herein].
Consultant shall conform to Hamilton County Surveyor’s Office Construction Plan Standards in the development of the Construction Plans for the Project. [Attached hereto as Exhibit “C” and incorporated fully herein].
Consultant shall conform to the Hamilton County Surveyor’s Office As-Built Submittal Standards in the development of the As-Built Submittal for the Project [Attached hereto as Exhibit “D” and incorporated fully herein].
The services provided by the Consultant shall include:
1. General Project Management and Administration including
a. Development of a master schedule of the Project that includes design development, permitting development, submittal, and approval, drainage board hearings, bidding, and construction
b. Confirmation of FEMA requirements related to design, bidding, construction, invoicing, cost tracking, etc.
c. Writing Drainage Board reconstruction reports.
d. Meetings for all aspects and phases of the project
e. Utility Coordination, mapping, and conflict identification including potholing and establishment of the elevation and state plane coordination location of existing utilities where crossed by the reconstructed Drain.
f. Coordination with stakeholders including but not limited to: Martin Marietta, City of Carmel, City of Carmel Utilities, Carmel-Clay Parks and Recreation, Hamilton County Highway Department.
2. Wetland assessment and delineation
a. Consultant shall physically flag the limits of any wetlands within the project area in the field.
b. Consultant shall utilize a GPS receiver to obtain the latitude and longitude of any flagging placed within the project area.
3. Report of Wetland Assessment
4. Tree inventory along the proposed drain alignment alternates
5. Geotechnical investigation of the reconstructed drain alignment alternates.
6. Drain alignment evaluation and selection
7. Surveying
8. Engineering design, including:
a. Hydraulic and hydrologic modeling of the reconstructed Drain
b. Hydraulic and hydrologic modeling of the White River at or near the proposed outfall of the reconstructed Drain if required by the permitting agencies.
c. Environmental design of any mitigation requirements associated with permits issued for the Project.
d. Reconstruction of the Drain to include cross section, capacity, interface with the reconstruction of the Hazel Dell Parkway Bridge, and possible lake on the east side of Hazel Dell Parkway.
9. Development of Opinion of Probable Cost for the reconstruction of the Drain.
10. Development of Construction Plans, Specifications, and Project Manual for the reconstruction of the Drain that may include alternates, phasing, and work by others.
11. Permit development and submission
12. Permit coordination
13. Bidding Assistance
14. Construction phase services including construction staking and periodic grade checks
15. Development and submittal of as-built information
16. Long-term mitigation monitoring services
17. Development of easement plats and descriptions for recording easements necessary for the reconstructed Drain.
4. Expected Deliverables
1. Project Schedule
2. Wetland Assessment Report
3. Tree Inventory Report
4. Geotechnical Report
5. Drain Alignment Recommendation
6. Hydraulics Report
7. Hydraulics Report as required by permitting agencies
8. Opinion of Probable Cost for Drain Reconstruction
9. Completed Permit Forms and Supporting Documents
10. Construction Plans and Project Manual for Drain Reconstruction
11. As-Built Files and Documents
12. Plats and Descriptions of Easements
13. Insurance Requirements Consultant shall conform to the Hamilton County Insurance Requirements Policy – Vendors, Contractors, and Events issued 12/08/25. [Attached hereto as Exhibit “E” and incorporated fully herein].
14. Evaluation Criteria Pursuant to state and federal requirements a qualifications-based selection method will be used to evaluate and select the consultant for this Project. The evaluation team will consist of Hamilton County employees who have direct knowledge of the work to be performed. SOQs will be evaluated using the following criteria and scoring:
| Past Performance |
| 25 |
| Permitting Agency Hydraulic Modeling Experience |
| 25 |
| Consultant’s Qualifications and Relevant Experience |
| 20 |
| Project Understanding and Approach |
| 15 |
| Capacity and Availability of Team |
| 15 |
| Total |
| 100 Points |
In accordance with 2 CFR § 200.320(b)(2)(iv) price shall not be used as a factor in the evaluation of this RFQ. All price or cost related items, which include, but are not limited to, cost proposals, direct salaries/wage rates, indirect cost rates, and other direct costs are prohibited from being used as evaluation criteria for this RFQ.
Pursuant to 2 CFR§ 200.319, no In-State or local preference will be used as a factor in the evaluation of this RFQ, except where a local presence will add value to the quality and efficiency of the project and such evaluation criteria does not exceed a nominal value.
Evaluation factors will therefore focus exclusively on qualifications-based criteria, including technical approach, project understanding, relevant experience, specialized expertise, professional licensure, staff capabilities, capacity to accomplish the work, and past performance.
15. Selection Following completion of evaluations, the Board will score and rank the three most highly qualified Consultants, consistent with 2 CFR § 200.320(b)(2)(iv). Scores will be compiled and submitted to the Board for concurrence. Notification of the final ranking will be provided to the three most highly qualified Consultants.
16. Cost Proposal and Negotiation Prior to requesting any cost proposal from the highest-ranked Consultant, the Board will prepare an independent cost estimate consistent with 2 CFR § 200.324(a). This estimate will include anticipated labor hours, classifications, other direct costs, and fixed fees, and will form the basis of cost negotiations.
Following completion of cost negotiations with the most highly qualified Consultant, the Board will enter into a contract using one of the payment methods permitted under 2 CFR §200.324. The Board will utilize either a Cost‑Plus‑Fixed‑Fee (“CPFF”) contract or a Cost‑Reimbursement contract for the selected Consultant.
17. Statement of Qualification Content and Organization SOQs should be prepared as simply as possible and provide a straightforward, concise description of the Consultant’s capabilities to satisfy the requirements of the scope of services requested in this RFQ. SOQ’s shall generally be organized as follows:
1. Cover Letter
a. (max. 2 pages) summarizing key qualifications.
2. Consultant Description
a. Provide the Consultant name, address of the responsible office from which the work will be performed, and the name and email address of the contact person authorized to negotiate for the associated work.
b. List all proposed sub consultants and the percentage of work to be performed by the prime consultant and each sub consultant.
3. Qualifications & Relevant Experience
a. List the Project Manager and other key staff members, including key subconsultant staff, and the percent of time the project manager will be committed for the contract, if selected.
b. Include project engineers for important disciplines and staff members responsible for the work.
c. Address the experience of the key staff members on similar projects and the staff qualifications relative to the required item qualifications.
4. Capacity and Availability of Team
a. Describe the capacity of consultant staff and their ability to perform the work in a timely manner relative to present workload.
5. Past Performance
a. List similar or related engineering design projects completed by your Consultant within the past ten (10) years.
6. Project Understanding & Approach
a. Provide a description of your project approach relative to the advertised services.
b. Address your Consultant’s technical understanding of the project or services, cost containment practices, innovative ideas and any other relevant information concerning your Consultant’s qualifications for the project.
18. RFQ Timeline & Submission Schedule All dates below are binding unless modified by addendum. Late submissions will not be accepted. The Hamilton County Drainage Board will move through the evaluation process as promptly as practicable.
| Phase |
| Description |
| Date / Time |
| RFQ Release & Public Notices |
| RFQ Issued via OpenGov |
| Monday, November 16, 2026 |
| First Public Notice Published |
| Monday, November 16, 2026 |
| Second Public Notice Published |
| Monday, November 23, 2026 |
| Questions Period |
| Deadline for submitting questions via OpenGov |
| Monday, November 30, 2026 by 3:00 PM ET |
| SOQ Submission Deadline |
| SOQs due via OpenGov no later than the start of the Hamilton County Drainage Board meeting |
| Monday, December 7, 2026 no later than the start of the Hamilton County Drainage Board meeting which begins at 12:00 PM ET |
| Evaluation |
| County Evaluation Committee reviews and scores all SOQs received by the deadline |
| Immediately following SOQ Submission Deadline |
19. Federal Requirements and Contract Provisions All Consultants responding to this RFQ are expected to comply with the federal contract provisions located in Exhibit A, attached hereto and made a part of this RFQ. Additionally, Consultants are advised that this RFQ is drafted based on the assumption that the Project will remain eligible for federal funds. Accordingly, the RFQ will conform to requirements of applicable federal law and FEMA regulations. The Board reserves the right to modify the procurement procedures described herein to address any concerns, conditions, or requirements of FEMA. The Board will notify Consultants of any such modifications via addenda.
20. Reservation of Rights The Board reserves the unrestricted right to:
1. The Board’s decision to enter into an eventual agreement with a Consultant will be made on the basis of the best qualified Consultant’s qualifications, project understanding and approach, relevant experience, and ability to deliver the Board with the best value. The Board reserves the right to reject all Responses and shall make a decision they believe is in the best interests of the County’s residence. The Board reserves the right to assemble a team to review the Responses received.
2. Pursuant to IC 5-22-18-2, the Board reserves the right to cancel or reject this RFQ in whole or in part.
3. The Board does not require the Consultant to submit a certified check/bid bond or other evidence of financial responsibility with its Response.
4. All Consultants will be accorded fair and equal treatment with respect to any opportunity for discussion and revision of SOQs. The Board may enter into discussion with Consultants to clarify and assure a full understanding of SOQs.
5. Hamilton County, Indiana, in accordance with Title VI of the Civil Rights Act of 1964, 78 Stat. 252, 42 USC 2000d to 2000d-4 and Title 49, Code of Federal Regulations, Department of Transportation, Subtitle A, Office the Secretary, Part 21, Non-Discrimination in Federally Assisted Programs of the Department of Transportation issued pursuant to such Act, hereby notifies all Consultants that it will affirmatively insure that in any contract entered into pursuant to this advertisement, minority business enterprises will be afforded full opportunity to submit SOQs in response to this invitation and will not be discriminated against on the grounds of race, color, or national origin in consideration for an award.
6. The Board may refuse to disclose the contents of SOQs during discussions with eligible Consultants.
7. Consultants shall not contact Hamilton County Board of Commissioners or any other voting body. All correspondence and questions for this RFQ should be handled through the RFQ Contact.
8. Submission of an SOQ does not guarantee award of a contract.
Disclaimer Regarding Exhibit A Exhibit A is provided solely for informational purposes. Its inclusion in this RFQ does not constitute, and shall not be interpreted as, an agreement, commitment, promise, or obligation — express or implied — by the Hamilton County Drainage Board (“Board”) to enter into any contract, nor does it create any contractual rights or expectations for any Consultant.
The terms, conditions, and requirements contained in Exhibit A are shared only to ensure that interested consultants are apprised of the federal-aid and FEMA contractual provisions that will apply if, and only if, the Board selects a Consultant for contract negotiations and a final agreement is executed.
No Consultant shall rely on Exhibit A as forming any part of a contract with the Board unless and until the Board formally awards a contract and the parties execute a written agreement incorporating those terms. The Board reserves the right to revise, supplement, or replace Exhibit A at any time prior to award.
EXHIBIT A
Federal Funding Contract Provisions
1. Incorporation. This Contract may be funded in whole or in part by federal grant dollars and is subject to the terms and conditions incorporated either directly or by reference in the following:
a. 2 C.F.R. Part 200 (“Uniform Guidance”), including Appendix II
b. 2 C.F.R. Subtitle A, Chapter II, Part 200 Uniform Administrative Requirements, Cost Principles, and Audit Requirements for Federal Awards
2. The Contractor must comply with all terms and conditions outlined in this Contract, including requirements imposed by program statutes and regulations, grant administration regulations, as applicable; and any regulations or limitations in any applicable appropriations acts.
3. Appendix II to Part 200 (A); Appendix II to Part 200 (B). Remedies for Breach; Termination for Cause/Convenience. If this contract is in excess of $10,000 and the contract does not include provisions for both termination for cause and termination for convenience by Hamilton County, including the manner by which it will be affected and the basis for settlement, then the following termination clauses shall apply. If this contract is for more than the simplified acquisition threshold (see 2 C.F.R. 200.88) at the time the contract is executed and does not provide for administrative, contractual, or legal remedies in instances where the Contractor violates or breaches the terms of the contract, then the following termination clauses shall apply and have precedence over the contract.
a. Termination for Convenience. Hamilton County may, by written notice to Contractor, terminate this contract for convenience, in whole or in part, and specifying the effective date thereof (“Notice of Termination for Convenience”). If the termination is for the convenience of Hamilton County, then Hamilton County shall compensate Contractor for work or materials fully and adequately provided through the effective date of termination. No amount shall be paid for unperformed work or materials not provided, including anticipated profit. Contractor shall provide documentation deemed adequate by Hamilton County to show the work actually completed or materials provided by Contractor prior to the effective date of termination. This contract shall terminate on the effective date of the Notice of Termination.
b. Termination for Cause. If Contractor fails to perform pursuant to the terms of this contract, Hamilton County shall provide written notice to Contractor specifying the default (“Notice of Default”). If Contractor does not cure such default within ten (10) calendar days of receipt of Notice of Default, Hamilton County may terminate this contract for cause. If Contractor fails to cure a default as set forth above, Hamilton County may, by written notice to Contractor, terminate this contract for cause, in whole or in part, and specifying the effective date thereof (“Notice of Termination for Cause”). If the termination is for cause, Contractor shall be compensated for that portion of the work or materials provided which has been fully and adequately completed and accepted by Hamilton County as of the date Hamilton County provides the Notice of Termination. In such case, Hamilton County shall have the right to take whatever steps it deems necessary to complete the project and correct Contractor’s deficiencies and charge the cost thereof to Contractor, who shall be liable for the full cost of Hamilton County’s corrective action, including reasonable overhead, profit and attorneys’ fees.
c. Reimbursement; Damages. Hamilton County shall be entitled to reimbursement for any compensation paid in excess of work rendered or materials provided and shall be entitled to withhold compensation for defective work or other damages caused by Contractor’s performance of the work.
d. Additional Termination Provisions. Upon receipt of a Notice of Termination, either for cause or for convenience, Contractor shall promptly discontinue the work unless the Notice directs to the contrary. Contractor shall deliver to Hamilton County and transfer title (if necessary) to all provided materials and completed work, and work in progress including drafts, documents, plans, forms, maps, products, graphics, computer programs and reports. The rights and remedies of the parties provided in this Section are in addition to any other rights and remedies provided by law or under this contract. Contractor acknowledges Hamilton County’s right to terminate this contract with or without cause as provided in this Section, and hereby waives any and all claims for damages that might arise from Hamilton County’s termination of this contract. Hamilton County shall not be liable for any costs other than the charges or portions thereof which are specified herein. Contractor shall not be entitled to payment for unperformed work or materials not provided, and shall not be entitled to damages or compensation for termination of work or supply of materials. If Hamilton County terminates this contract for cause, and it is later determined that the termination for cause was wrongful, the termination shall automatically be converted to and treated as a termination for convenience. In such event, Contractor shall be entitled to receive only the amounts payable under this Section, and Contractor specifically waives any claim for any other amounts or damages, including, but not limited to, any claim for consequential damages or lost profits. The rights and remedies of Hamilton County provided in this Section shall not be exclusive and are in addition to any other rights and remedies provided by law, equity or under this
4. Equal Employment Opportunity. During the performance of this contract, the Contractor agrees as follows:
a. The contractor will not discriminate against any employee or applicant for employment because of race, color, religion, sex, sexual orientation, gender identity, or national origin. The contractor will take affirmative action to ensure that applicants are employed, and that employees are treated during employment without regard to their race, color, religion, sex, sexual orientation, gender identity, or national origin. Such action shall include, but not be limited to the following:
i. Employment, upgrading, demotion, or transfer; recruitment or recruitment advertising; layoff or termination; rates of pay or other forms of compensation; and selection for training, including apprenticeship. The contractor agrees to post in conspicuous places, available to employees and applicants for employment, notices to be provided setting forth the provisions of this nondiscrimination clause.
b. The contractor will, in all solicitations or advertisements for employees placed by or on behalf of the contractor, state that all qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, or national origin.
c. The contractor will not discharge or in any other manner discriminate against any employee or applicant for employment because such employee or applicant has inquired about, discussed, or disclosed the compensation of the employee or applicant or another employee or applicant. This provision shall not apply to instances in which an employee who has access to the compensation information of other employees or applicants as a part of such employee's essential job functions discloses the compensation of such other employees or applicants to individuals who do not otherwise have access to such information, unless such disclosure is in response to a formal complaint or charge, in furtherance of an investigation, proceeding, hearing, or action, including an investigation conducted by the employer, or is consistent with the contractor's legal duty to furnish information.
d. The contractor will send to each labor union or representative of workers with which he has a collective bargaining agreement or other contract or understanding, a notice to be provided advising the said labor union or workers' representatives of the contractor's commitments under this section, and shall post copies of the notice in conspicuous places available to employees and applicants for employment.
e. The contractor will comply with all provisions of Executive Order 11246 of September 24, 1965, and of the rules, regulations, and relevant orders of the Secretary of Labor.
f. The contractor will furnish all information and reports required by Executive Order 11246 of September 24, 1965, and by rules, regulations, and orders of the Secretary of Labor, or pursuant thereto, and will permit access to his books, records, and accounts by the administering agency and the Secretary of Labor for purposes of investigation to ascertain compliance with such rules, regulations, and orders.
g. In the event of the contractor's noncompliance with the nondiscrimination clauses of this contract or with any of the said rules, regulations, or orders, this contract may be canceled, terminated, or suspended in whole or in part and the contractor may be declared ineligible for further Government contracts or federally assisted construction contracts in accordance with procedures authorized in Executive Order 11246 of September 24, 1965, and such other sanctions may be imposed and remedies invoked as provided in Executive Order 11246 of September 24, 1965, or by rule, regulation, or order of the Secretary of Labor, or as otherwise provided by law.
h. The contractor will include the portion of the sentence immediately preceding subsection (A) of section 2 of this contract, and the provisions of subsections (A) through (H) in every subcontract or purchase order unless exempted by rules, regulations, or orders of the Secretary of Labor issued pursuant to section 204 of Executive Order 11246 of September 24, 1965, so that such provisions will be binding upon each subcontractor or vendor. The contractor will take such action with respect to any subcontract or purchase order as the administering agency may direct as a means of enforcing such provisions, including sanctions for noncompliance:
i. Provided, however, that in the event a contractor becomes involved in, or is threatened with, litigation with a subcontractor or vendor as a result of such direction by the administering agency, the contractor may request the United States to enter into such litigation to protect the interests of the United States.
j. The applicant further agrees that it will be bound by the above equal opportunity clause with respect to its own employment practices when it participates in federally assisted construction work: Provided, That if the applicant so participating is a State or local government, the above equal opportunity clause is not applicable to any agency, instrumentality or subdivision of such government which does not participate in work on or under the contract.
k. The applicant agrees that it will assist and cooperate actively with the administering agency and the Secretary of Labor in obtaining the compliance of contractors and subcontractors with the equal opportunity clause and the rules, regulations, and relevant orders of the Secretary of Labor, that it will furnish the administering agency and the Secretary of Labor such information as they may require for the supervision of such compliance, and that it will otherwise assist the administering agency in the discharge of the agency's primary responsibility for securing compliance.
l. The applicant further agrees that it will refrain from entering into any contract or contract modification subject to Executive Order 11246 of September 24, 1965, with a contractor debarred from, or who has not demonstrated eligibility for, Government contracts and federally assisted construction contracts pursuant to the Executive Order and will carry out such sanctions and penalties for violation of the equal opportunity clause as may be imposed upon contractors and subcontractors by the administering agency or the Secretary of Labor pursuant to Part II, Subpart D of the Executive Order. In addition, the applicant agrees that if it fails or refuses to comply with these undertakings, the administering agency may take any or all of the following actions: Cancel, terminate, or suspend in whole or in part this grant (contract, loan, insurance, guarantee); refrain from extending any further assistance to the applicant under the program with respect to which the failure or refund occurred until satisfactory assurance of future compliance has been received from such applicant; and refer the case to the Department of Justice for appropriate legal proceedings.
5. Davis-Bacon Act.
a. All transactions regarding this contract shall be done in compliance with the Davis-Bacon Act (40 U.S.C. 3141- 3144, and 3146-3148) and the requirements of 29 C.F.R. pt. 5 as may be applicable. The Contractor shall comply with 40 U.S.C. 3141-3144, and 3146-3148 and the requirements of 29 C.F.R. pt. 5 as applicable.
b. Contractors are required to pay wages to laborers and mechanics at a rate not less than the prevailing wages specified in a wage determination made by the Secretary of Labor.
c. Additionally, contractors are required to pay wages not less than once a week.
6. Copeland “Anti-Kickback” Act.
a. Contractor. The Contractor shall comply with 18 U.S.C. § 874, 40 U.S.C. § 3145, and the requirements of 29 C.F.R. Part 3 as may be applicable, which are incorporated by reference into this contract.
b. Subcontracts. The Contractor or Subcontractor shall insert in any subcontracts the clause above and such other clauses as FEMA may by appropriate instructions require, and a clause requiring the subcontractors to include these clauses in any lower tier subcontracts. The Prime Contractor shall be responsible for the compliance by any subcontractor or lower tier subcontractor with all these contract clauses.
c. Breach. A breach of the contract clauses above may be grounds for termination of the contract, and for debarment as a contractor and subcontractor as provided in 29 C.F.R. § 5.12.
7. Contract Work Hours and Safety Standards Act.
a. Overtime requirements. No contractor or subcontractor contracting for any part of the contract work which may require or involve the employment of laborers or mechanics shall require or permit any such laborer or mechanic in any workweek in which he or she is employed on such work to work in excess of forty hours in such workweek unless such laborer or mechanic receives compensation at a rate not less than one and one-half times the basic rate of pay for all hours worked in excess of forty hours in such workweek.
b. Violation; liability for unpaid wages; liquidated damages. In the event of any violation of the clause set forth in paragraph (5)(A) of this section the Contractor and any subcontractor responsible therefor shall be liable for the unpaid wages. In addition, such contractor and subcontractor shall be liable to the United States (in the case of work done under contract for the District of Columbia or a territory, to such District or to such territory), for liquidated damages. Such liquidated damages shall be computed with respect to each individual laborer or mechanic, including watchmen and guards, employed in violation of the clause set forth in paragraph (5)(A) of this section, in the sum of $27 for each calendar day on which such individual was required or permitted to work in excess of the standard workweek of forty hours without payment of the overtime wages required by the clause set forth in paragraph (5)(A) of this section.
c. Withholding for unpaid wages and liquidated damages. The Federal Emergency Management Agency (“FEMA”) shall upon its own action or upon written request of an authorized representative of the Department of Labor withhold or cause to be withheld, from any moneys payable on account of work performed by the Contractor or subcontractor under any such contract or any other Federal contract with the same prime Contractor, or any other federally-assisted contract subject to the Contract Work Hours and Safety Standards Act, which is held by the same prime Contractor, such sums as may be determined to be necessary to satisfy any liabilities of such Contractor or subcontractor for unpaid wages and liquidated damages as provided in the clause set forth in paragraph (5)(B) of this section.
d. Subcontracts. The Contractor or subcontractor shall insert in any subcontracts the clauses set forth in paragraph (5)(A) through (D) of this section and also a clause requiring the subcontractors to include these clauses in any lower tier subcontracts. The prime Contractor shall be responsible for compliance by any subcontractor or lower tier subcontractor with the clauses set forth in paragraphs (5)(A) through (D) of this section.
8. Rights to Inventions Made Under a Contract or Agreement.
a. If this Contract is funded by a federal “funding agreement” as defined under 37 C.F.R. §401.2 (a) and the recipient or subrecipient wishes to enter into a contract with a small business firm or nonprofit organization regarding the substitution of parties, assignment or performance of experimental, developmental, or research work under that “funding agreement,” the recipient or subrecipient must comply with 37 C.F.R. Part 401, “Rights to Inventions Made by Nonprofit Organizations and Small Business Firms Under Government Grants, Contracts and Cooperative Agreements,” and any implementing regulations issued by the awarding agency.
9. Clean Air Act and the Federal Water Pollution Control Act.
a. If this Contract is in excess of $150,000, the Contractor must comply with all applicable standards, orders, and regulations issued under the Clean Air Act (42 U.S.C. 7401-7671q) and the Federal Water Pollution Control Act (33 U.S.C. 1251-1387), and during performance of this Contract the Contractor agrees as follows:
b. Clean Air Act
i. The Contractor agrees to comply with all applicable standards, orders or regulations issued pursuant to the Clean Air Act, as amended, 42 U.S.C. § 7401 et seq.
ii. The Contractor agrees to report each violation to Hamilton County and understands and agrees that Hamilton County will, in turn, report each violation as required to assure notification to the Federal Emergency Management Agency or the applicable federal awarding agency, and the appropriate Environmental Protection Agency Regional Office.
iii. The Contractor agrees to include these requirements in each subcontract exceeding $150,000 financed in whole or in part with Federal assistance provided by FEMA or the applicable federal awarding agency.
c. Federal Water Pollution Control Act
i. The Contractor agrees to comply with all applicable standards, orders, or regulations issued pursuant to the Federal Water Pollution Control Act, as amended, 33 U.S.C. 1251 et seq.
ii. The Contractor agrees to report each violation to Hamilton County and understands and agrees that Hamilton County will, in turn, report each violation as required to assure notification to the Federal Emergency Management Agency or the applicable federal awarding agency, and the appropriate Environmental Protection Agency Regional Office.
iii. The Contractor agrees to include these requirements in each subcontract exceeding $150,000 financed in whole or in part with Federal assistance provided by FEMA or the applicable federal awarding agency.
10. Debarment and Suspension.
a. A “contract award” (see 2 C.F.R. 180.220) must not be made to parties listed on the government-wide exclusions in the System for Award Management (SAM), in accordance with the OMB guidelines at 2 C.F.R. 180 that implement Executive Orders 12549 (51 FR 6370; February 21, 1986) and 12689 (54 FR 34131; August 18, 1989), “Debarment and Suspension.” SAM Exclusions contains the names of parties debarred, suspended, or otherwise excluded by agencies, as well as parties declared ineligible under statutory or regulatory authority other than Executive Order 12549.
b. This Contract is a covered transaction for purposes of 2 C.F.R. Part 180 and 2 C.F.R. Part 3000. As such, the Contractor is required to verify that none of the Contractor’s principals (defined at 2 C.F.R. § 180.995) or its affiliates (defined at 2 C.F.R. § 180.905) are excluded (defined at 2 C.F.R. § 180.940) or disqualified (defined at 2 C.F.R. § 180.935).
c. The Contractor must comply with 2 C.F.R. Part 180, subpart C and 2 C.F.R. Part 3000, subpart C, and must include a requirement to comply with these regulations in any lower tier covered transaction it enters into.
d. This certification is a material representation of fact relied upon by Hamilton County. If it is later determined that the Contractor did not comply with 2 C.F.R. Part. 180, subpart C and 2 C.F.R. Part. 3000, subpart C, in addition to remedies available to Hamilton County, the Federal Government may pursue available remedies, including but not limited to suspension and/or debarment.
e. The bidder or proposer agrees to comply with the requirements of 2 C.F.R. Part 180, subpart C and 2 C.F.R. Part 3000, subpart C while this offer is valid and throughout the period of any contract that may arise from this offer. The bidder or proposer further agrees to include a provision requiring such compliance in its lower tier covered transactions.
11. Byrd Anti-Lobbying Amendment, 31 U.S.C. § 1352 (as amended).
a. Contractor has applied or bid for an award of more than $100,000 and shall file the required certification in Exhibit G – Byrd Anti-Lobbying Certification attached to the end of this Contract. Each tier certifies to the tier above that it will not and has not used federally appropriated funds to pay any person or organization for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, officer or employee of Congress, or an employee of a Member of Congress in connection with obtaining any federal contract, grant, or any other award covered by 31 U.S.C. § 1352. Each tier shall also disclose any lobbying with non-federal funds that takes place in connection with obtaining any federal award. Such disclosures are forwarded from tier to tier up to the recipient who in turn will forward the certification(s) to the federal awarding agency.
12. Procurement of Recovered Materials.
a. If this Contract is a procurement to purchase products or items designated by the EPA under 40 C.F.R. part 247 during the course of a fiscal year, then under 2 C.F.R. 200.323, Contractors must comply with section 6002 of the Solid Waste Disposal Act, as amended by the Resource Conservation and Recovery Act.
i. In the performance of this contract, the Contractor shall make maximum use of products containing recovered materials that are EPA-designated items unless the product cannot be acquired:
ii. Competitively within a timeframe providing for compliance with the contract performance schedule;
iii. Meeting contract performance requirements; or
iv. At a reasonable price.
b. Information about this requirement, along with the list of EPA- designated items, is available at EPA’s Comprehensive Procurement Guidelines web site, https://www.epa.gov/smm/comprehensive-procurement-guideline-cpg-program.
c. The Contractor also agrees to comply with all other applicable requirements of Section 6002 of the Solid Waste Disposal Act.
13. Prohibition on Contracting for Covered Telecommunications Equipment or Services.
a. Contractor acknowledges and agrees that Section 889(b) of the John S. McCain National Defense Authorization Act for Fiscal Year 2019, Pub. L. No. 115-232 (the “McCain Act”), and 2 C.F.R. §200.216, prohibit the obligation or expending of federal award funds on certain telecommunication products or with certain entities for national security reasons on or after August 13, 2020.
b. During performance of this Contract, the Contractor agrees as follows:
i. Definitions. As used in this Section J. Prohibition on Contracting for Covered Telecommunications Equipment or Services (“Section J”):
1. the terms “backhaul,” “critical technology,” “interconnection arrangements,” “reasonable inquiry,” “roaming,” and “substantial or essential component” have the meanings defined in 48 CFR § 4.2101;
2. the term “covered foreign country” has the meanings defined in § 889(f)(2) of the McCain Act; and
3. the term “covered telecommunications equipment or services” has the meaning defined in § 889(f)(3) of the McCain Act.
ii. Prohibitions.
1. Unless an exception in paragraph (iii) of this Section applies, neither the Contractor nor any of its subcontractors may use funds received under this Contract to:
a. Procure or obtain any equipment, system, or service that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology of any system;
b. Enter into, extend, or renew a contract to procure or obtain any equipment, system, or service that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology of any system;
c. Enter into, extend, or renew a contract with an entity that uses any covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system; or
d. Provide, as part of its performance of this contract, subcontract, or other contractual instrument, any equipment, system, or service that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system.
iii. Exceptions. This Section does not prohibit Contractor from providing—
1. A service that connects to the facilities of a third-party, such as backhaul, roaming, or interconnection arrangements; or
2. Telecommunications equipment that cannot route or redirect user data traffic or permit visibility into any user data or packets that such equipment transmits or otherwise handles.
iv. Reporting requirement. In the event the Contractor identifies covered telecommunications equipment or services used as a substantial or essential component of any system, or as critical technology as part of any system, during contract performance, or the Contractor is notified of such by a subcontractor at any tier or by any other source, the Contractor shall report the information in paragraph (iv) (1) of this Section to the recipient or subrecipient, unless elsewhere in this contract are established procedures for reporting the information.
1. The Contractor shall report the following information pursuant to paragraph (iv) of this Section:
a. Within one business day from the date of such identification or notification: The contract number; the order number(s), if applicable; supplier name; supplier unique entity identifier (if known); supplier Commercial and Government Entity (CAGE) code (if known); brand; model number (original equipment manufacturer number, manufacturer part number, or wholesaler number); item description; and any readily available information about mitigation actions undertaken or recommended.
b. Within 10 business days of submitting the information in paragraph (iv)(1)(a) of this Section: Any further available information about mitigation actions undertaken or recommended. In addition, the Contractor shall describe the efforts it undertook to prevent use or submission of covered telecommunications equipment or services, and any additional efforts that will be incorporated to prevent future use or submission of covered telecommunications equipment or services.
2. Subcontracts. The Contractor shall insert the substance of this Section in all subcontracts and other contractual instruments.
14. Domestic Preferences for Procurements
a. As appropriate, and to the extent consistent with law, the Contractor should, to the greatest extent practicable, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States. This includes, but is not limited to iron, aluminum, steel, cement, and other manufactured products.
b. For purposes of this Section 39 - Domestic Preferences for Procurements:
i. “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stage through the application of coatings, occurred in the United States.
ii. “Manufactured products” mean items and construction materials composed in whole or in part of non-ferrous metals such as aluminum; plastics and polymer-based products such as polyvinyl chloride pipe; aggregates such as concrete; glass, including optical fiber; and lumber.
15. Copyright and Data Rights.
a. Pursuant to 2 CFR § 200.315(b), Hamilton County may copyright any work which is subject to copyright and was developed, or for which ownership was acquired, under a Federal award. The Federal awarding agency reserves a royalty-free, nonexclusive and irrevocable right to reproduce, publish, or otherwise use the work for Federal purposes, and to authorize others to do so.
16. Access to Records.
a. The following access to records requirements apply to this Contract:
i. The Contractor agrees to provide Hamilton County, the FEMA Administrator, the Comptroller General of the United States, or any of their authorized representatives access to any books, documents, papers, and records of the Contractor which are directly pertinent to this contract for the purposes of making audits, examinations, excerpts, and transcriptions.
ii. The Contractor agrees to permit any of the foregoing parties to reproduce by any means whatsoever or to copy excerpts and transcriptions as reasonably needed.
iii. The Contractor agrees to provide the FEMA Administrator or his authorized representatives access to construction or other work sites pertaining to the work being completed under the contract.
iv. In compliance with the Disaster Recovery Act of 2018, Hamilton County and the Contractor acknowledge and agree that no language in this contract is intended to prohibit audits or internal reviews by the FEMA Administrator or the Comptroller General of the United States.
17. DHS Seal, Logo, and Flags.
a. The Contractor shall not use the DHS seal(s), logos, crests, or reproductions of flags or likenesses of DHS agency officials without specific FEMA pre-approval.
18. Compliance with Federal Law, Regulations, and Executive Orders.
a. This is an acknowledgement that FEMA financial assistance may be used to fund all or a portion of the Contract. The Contractor will comply with all applicable Federal law, regulations, executive orders, FEMA policies, procedures, and directives.
19. No Obligation by Federal Government.
a. The Federal Government is not a party to this Contract and is not subject to any obligations or liabilities to the non-Federal entity, Contractor, or any other party pertaining to any matter resulting from the Contract.
20. Program Fraud and False or Fraudulent Statement or Related Acts.
a. The Contractor acknowledges that 31 U.S.C. Chap. 38 (Administrative Remedies for False Claims and Statements) applies to the Contractor’s actions pertaining to this Contract.
EXHIBIT B
Hamilton County Surveyor’s Office Survey Standards
GENERAL
· Surveyor (Consultant), Crew Chief (Consultant), Engineer (Hamilton County Surveyor’s Office) and Inspector (Hamilton County Surveyor’s Office) shall walk the project prior to the start.
· Surveyor (Contractor) shall notify property owners of entry via USPS before starting project.
· A field book shall be created for each project. Basic field book data shall include, but is not limited to, page numbers, date of survey, field crew with duties, sketches, flow arrows, etc.
· The Engineer (Surveyor’s Office) & Inspector (Surveyor’s Office) shall flag any outlet pipes prior to start of project during low flow conditions. This will allow the outlets to be located even if submerged at time of field survey.
· Photo documentation of key items shall be provided to the Surveyor’s Office. Items to be photographically documented and labeled with location numbers. This will include, but not be limited to crossings, bridges, outlets, structures, farm crossings/bridges, washouts, etc. Documentation shall include the photo that is numbered with indication of where photo taken along with direction and view taken.
· Field crew consistency shall be maintained throughout each project. One crew shall start and finish each project.
SURVEYING
· Temporary Benchmarks TBMs and Horizontal Control Points (CPs) shall be placed in locations that will not be disturbed during the construction phase. These same TBMs and CPs shall then be utilized for construction staking, grade checks during construction, and as-built surveying. TBMs and CPs shall be clearly marked, referenced, and noted in the field book.
· Stakes that interfere with other activities shall be removed at the end of the project.
· Flowline (FL) locations (X,Y,Z) of the channel shall be taken every 100’, unless the channel alignment changes at an angle or bend. Through angles and bends, the FL shall be located (X,Y,Z) every 50’ on center or close enough to accurately capture FL angles, bends or abnormalities. At a minimum, there shall be a FL location (X,Y,Z) at the start, middle, and end of each bend.
· At channel bends and angles, top of bank, toe of slope, & ground shots shall be located at each flowline location (X,Y,Z).
· Cross Section (X-Sec) locates of the channel shall be taken every 200’ or when an apparent change in the cross section of the channel occurs. X-Sec locates shall be taken perpendicular to the channel as follows: ground shot, top of bank, toe of slope, flowline. Bends shall have adequate locates to accurately draw & design bend protection such as rip-rap, gabion baskets, etc. Any intermediate grade breaks on the side slope must also be located.
· Cross Section of open ditch tributaries & swales…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .