RFQ 19DJ1025Q0016 INSTALLATION OF INTERIOR POTABLE WATER STORAGE TANK CONTRACT.pdf

Embassy of the United States of America Djibouti, Djibouti

August 27, 2025

Dear Prospective Quoter:

SUBJECT: Request For Quotation Number 19DJ1025Q0016

Enclosed is a Request for Quotation (RFQ) for 19DJ1025Q0016 INSTALLATION OF INTERIOR POTABLE WATER STORAGE TANK CONTRACT. If you would like to submit quotation, follow the instruction in sections 3 of the solicitation, complete the required portions on the attached document, and submit it to the address show on the Standard Form 1449 that follows this letter.

The U.S. Government intends to award a contract/purchase order to the responsible company submitting an acceptable offer at lowest price. We intend to award a contract/purchase order based on initial quotation, without holding discussions, although we may hold discussions with companies in the competitive ranges if there is a need to do so.

The Embassy intends to conduct a pre-quotation conference. The pre-proposal conference will be held on September 09, 2025, at 10:00 a.m. at the embassy premises at Haramous. Prospective offerors/quoters should contact the embassy procurement team at djiboutiprocbids@state.gov and copy to kayadse@state.gov by September 07, 2025, at 12:00 p.m. for additional information or to arrange entry to the building.

Quotations are due Sept 18, 2025, at 16:30 P.M. No quotations will be accepted after this time.

Proposals must be in English and incomplete proposals will not be accepted.

Submitted quotations, including price, must be valid for no less than four months from the Government receipt of quotation.

Your quotation must be submitted electronically to djiboutiprocbids@state.gov and copy to kayadse@state.gov . It is important to make sure the submission is made in made specific size and format; in MS-Word 2007/2010 or MS-Excel 2007/2010 OR Adobe Acrobat(Pdf) file format.

The file size must not exceed 30MB. If the file size should exceed the 30M, the submission must be made in separate files and attached to separate email with less than 30MB each.

In order for a quotation to be considered, you must also complete and submit the following:

1. SF-1449

2. Section 1, Pricing

3. Section 5, Representations and Certifications and ensure compliance with FAR

52.229-11 is completed with IRS Form W-14 found at www.irs.goc/w14

4. Additional information as required in Section 3

5. Proof of SAM Registration mailto:djiboutiprocbids@state.gov mailto:kayadse@state.gov

Offerors shall be registered in the SAM (System for Award Management) database at https://www.sam.gov prior to submittal of their offer/proposal as prescribed under FAR 4.1102.

Failure to be registered at time of proposal submission may deem the offeror’s proposal to be considered non-responsible and no further consideration will be given. Therefore, offerors are highly encouraged to register immediately if they are interested in submitting a response to this requirement.

Sincerely, Jesse C. Flowers Contracting Officer

TABLE OF CONTENTS

Section 1 - The Schedule

• Bid Schedule

• SF 1449 cover sheet

• Continuation To SF-1449, RFQ Number 19DJ1025Q0016, Prices, Block 23

• Continuation To SF-1449, RFQ Number 19DJ1025Q0016 Schedule Of Supplies/Services, Block 20 Description/Specifications/Work Statement

• Attachment 1 to Description/Specifications/Performance Work Statement, Government Furnished Property

Section 2 - Contract Clauses

• Contract Clauses

• Addendum to Contract Clauses - FAR and DOSAR Clauses not Prescribed in Part 12

Section 3 - Solicitation Provisions

• Solicitation Provisions

• Addendum to Solicitation Provisions - FAR and DOSAR Provisions not Prescribed in

Part 12

Section 4 - Evaluation Factors

• Evaluation Factors

• Addendum to Evaluation Factors - FAR and DOSAR Provisions not Prescribed in

Part 12

Section 5 - Representations and Certifications

• Offeror Representations and Certifications

• Addendum to Offeror Representations and Certifications - FAR and DOSAR

Provisions not Prescribed in Part 12

Bid Schedule:

The bid schedule shall be as follows:

Pre-quotation conference and site visit date

09/09/2025 at 10:00 a.m.

Offerors contract details submission deadline

09/07/2025 at 12:00 p.m.

Request for Information deadlines

Potential contractor: 09/13/2025 at 12:00p.m.

Requesting officer: 09/15/2025 at 12:00 p.m.

Quotation due date

Submitted quotations, including price, must be valid for no less than four months from Government receipt of quotation.

09/18/2025 at 16:30 p.m.

TEP Drafting

From Sept 21 to COB 22 Sept, 2025

Technical Evaluation Result Report

From Sept 23 to COB 24 Sept, 2025

Award Decision

From Sept 25 to COB 28 Sept, 2025

Line item and quantity:

No. Task Description Qty Unit Cost

(USD)

Total Cost

(USD)

1 Disassemble, disconnect, and remove existing tank

1 Each

2 Supply and install fiberglass 6,000-gallon potable water tank (NSF 61 certified, with insulation)

1 unit

3 Construct or repair reinforced concrete pad (with slope, rebar, curing)

1 each

4 Supply and install CPVC fittings, valves, couplings, flanges

1 lot

5 Install gallon-level indicator 1 unit 6 Install ladders (internal and external, non-corrosive material) 1 set

7 Provide and install screened air vent

1 unit

8 Electrical works (power supply for sensor and level indicator, cabling, conduit)

1 lot

9 Cleaning, disinfection, flushing, and bacteriological testing (AWWA C652 protocol)

1 lot

10 Demolition waste removal and environmentally safe disposal

1 lot

11 Site access and safety preparation (temporary barriers, signage, PPE compliance)

1 lot

12 Skilled labor for tank installation, testing, and plumbing integration

1 lot

13 System commissioning, testing, and O&M manual submission

1 lot

14 Contractor overhead and general conditions (admin, supervision, insurance, mobilization)

1 lot

15 Profit / Fee 1 each 16 Contingency (2.5%) 1 each

TOTAL ESTIMATION COST

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

1. REQUISITION NUMBER

PR15567131

PAGE 1 OF

2. CONTRACT NO.

3. AWARD/EFFECTIVE

DATE

4. ORDER NUMBER

5. SOLICITATION

NUMBER

19DJ1025Q0016

6. SOLICITATION ISSUE

DATE

08/27/2025

7. FOR SOLICITATION

INFORMATION CALL:

a. NAME

JESSE C. FLOWERS

b. TELEPHONE NUMBER (No collect calls)

21453060

8. OFFER DUE DATE/

LOCAL TIME

09/18/2025

9. ISSUED BY

CODE

10. THIS ACQUISITION

IS

UNRESTRICTED

SET ASIDE:____ %

FOR: GENERAL SERVICES OFFICER

SMALL BUSINESS WOMEN-OWNED SMALL BUSINESS

U.S. EMBASSY

DJIBOUTI

Tel: 21 453060

HUBZONE SMALL

BUSINESS

(WOSB) ELLIGIBLE UNDER THE WOMEN-

OWNED

SMALL BUSINESS PROGRAM NAICS:

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

EDWOSB

8 (A) SIZE STANDARD:

11. DELIVERY FOR FOB

DESTINAT-

TION UNLESS BLOCK IS

MARKED

SEE SCHEDULE

12. DISCOUNT TERMS 13a. THIS CONTRACT IS A

RATED ORDER

UNDER

DPAS (15 CFR 700)

13b. RATING

14. METHOD OF SOLICITATION

RFQ IFB RFP

15. DELIVER TO CODE 16. ADMINISTERED BY CODE

U.S. EMBASSY DJIBOUTI

BP 185 LOT NUMBER 350-B

LOTISSEMENT HARAMOUS

TEL 00253 21 45 30 00

REPUBLIC OF DJIBOUTI

U.S Embassy Djibouti 350-B, Lotissement Haramous Djibouti, Republic of Djibouti

17a. CONTRACTOR/

OFFERER

COD

E

FACILIT

Y CODE

18a. PAYMENT WILL BE MADE BY CODE

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT

SUCH ADDRESS IN

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS

BLOCK

19.

ITEM NO.

20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTIT

Y

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

INSTALLATION OF INTERIOR

POTABLE WATER STORAGE TANK

CONTRACT

service

25. ACCOUNTING AND APPROPRIATION DATA

26. TOTAL AWARD AMOUNT (For Govt. Use Only)

27a.SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5

ARE ATTACHED. ADDENDA

ARE ARE NOT

ATTACHED

27b.CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS

ATTACHED. ADDENDA

ARE ARE NOT

ATTACHED

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND

RETURN _1___ COPIES TO ISSUING OFFICE. CONTRACTOR AGREES

TO FURNISH AND DELIVER ALL ITEMS SET FORTH OR OTHERWISE

IDENTIFIED ABOVE AND ON ANY ADDITIONAL SHEETS SUBJECT TO

THE TERMS AND CONDITIONS SPECIFIED HEREIN

29. AWARD OF CONTRACT: REF. _________________ OFFER

DATED ____________. YOUR OFFER ON SOLICITATION (BLOCK 5),

INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET

FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING

OFFICER)

30b. NAME AND TITLE OF SIGNER (Type or print)

30c. DATE SIGNED

31b. NAME OF CONTRACTING OFFICER (Type or print)

31c. DATE SIGNED

CONTINUATION TO SF-1449

RFQ NUMBER 19DJ1025Q0016

PRICES, BLOCK 23

I. PERFORMANCE WORK STATEMENT

A. The purpose of this firm fixed for INSTALLATION OF INTERIOR POTABLE WATER

STORAGE TANK CONTRACT in accordance with Attachment A.

B. The contract will be for a one-time service.

II. QUALITY ASSURANCE AND SURVEILLANCE PLAN (QASP)

This plan provides an effective method to promote satisfactory contractor performance. The QASP provides a method for the Contracting Officer's Representative (COR) to monitor Contractor performance, advise the Contractor of unsatisfactory performance, and notify the Contracting Officer of continued unsatisfactory performance. The Contractor, not the Government, is responsible for management and quality control to meet the terms of the contract. The role of the Government is to monitor quality to ensure that contract standards are achieved.

Performance Objective Scope of Work

Paragraphs Performance Threshold

Services.

Performs INSTALLATION OF

INTERIOR POTABLE WATER

STORAGE TANK CONTRACT.

Design thru warranty.

All required services are performed and no more than one

(1) customer complaint is received per month.

1. SURVEILLANCE.

The COR will receive and document all complaints from Government personnel regarding the services provided. If appropriate, the COR will send the complaints to the Contractor for corrective action.

2. STANDARD.

The performance standard is that the Government receives no more than one (1) customer complaint per month. The COR shall notify the Contracting Officer of the complaints so that the Contracting Officer may take appropriate action to enforce the inspection clause (FAR 52.212.4, Contract Terms and Conditions-Commercial Items (May 2001), if any of the services exceed the standard.

3. PROCEDURES.

(a) If any Government personnel observe unacceptable services, either incomplete work or required services not being performed they should immediately contact the COR.

(b) The COR will complete appropriate documentation to record the complaint.

(c) If the COR determines the complaint is invalid, the COR will advise the complainant. The COR will retain the annotated copy of the written complaint for his/her files.

(d) If the COR determines the complaint is valid, the COR will inform the Contractor and give the Contractor additional time to correct the defect, if additional time is available.

The COR shall determine how much time is reasonable.

(e) The COR shall, as a minimum, orally notify the Contractor of any valid complaints.

(f) If the Contractor disagrees with the complaint after investigation of the site and challenges the validity of the complaint, the Contractor will notify the COR. The COR will review the matter to determine the validity of the complaint.

(g) The COR will consider complaints as resolved unless notified otherwise by the complainant.

(h) Repeat customer complaints are not permitted for any services. If a repeat customer complaint is received for the same deficiency during the service period, the COR will contact the Contracting Officer for appropriate action under the Inspection clause.

III. PRICING

The price listed below shall include all labor, insurance (see FAR 52.228-4 and 52.228-5), overhead, and profit. The Government will pay the Contractor the fixed price per month for standard services and a fixed rate for any temporary additional services that have been satisfactorily performed.

After contract award and submission of acceptable insurance certificates, the Contracting Officer shall issue a Notice to Proceed. The Notice to Proceed will establish a date (a minimum of ten

(10) days from start date listed in Notice to Proceed unless the Contractor agrees to an earlier date) on which performance shall start.

Line Description Price Service

Total

INSTALLATION OF

INTERIOR POTABLE

WATER STORAGE

TANK CONTRACT

Note: The submitted quotations, including price, must be valid for no less than four months from Government receipt of quotation.

IV. VALUE ADDED TAX VAT VERSION A

VALUE ADDED TAX. Value Added Tax (VAT) is not included in the CLIN rates. Instead, it will be priced as a separate Line Item in the contract and on Invoices. Local law dictates the portion of the contract price that is subject to VAT; this percentage is multiplied only against that portion. It is reflected for each performance period.

CONTINUATION TO SF-1449,

RFQ NUMBER 19DJ1025Q0016

SCHEDULE OF SUPPLIES/SERVICES, BLOCK 20

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

Project Description

The U.S. Embassy in Djibouti intends to replace the existing interior plastic water storage tank, located inside the water treatment facility, with a new modular Glass Reinforced Plastic (GRP) water tank. The scope of work is Design-Build construction and includes complete disassembly and removal of the old tank, the design and installation of a new GRP tank and appurtenances, with all required accessories and sensors, hydrostatic testing, final disinfection, and commissioning.

1. Design Phase

The contractor shall:

a. Conduct a detailed site survey to verify all dimensions, access constraints, and the condition of the existing tank, connections, equipment, and concrete foundation. A dimensional verification survey must be conducted to confirm that the proposed modular tank and all associated appurtenances will fit the intended installation footprint.

Particular attention must be paid to clearance for installation, maintenance access, and structural support conditions.

b. The contractor shall verify that all system components (piping, valves, sensors, and flanges) are compatible with the existing water distribution system and meet OBO requirements including system redundancy, maintenance access, and leak prevention.

Designs shall include a site adapted schematic showing utility interface points and routing diagrams. Any need for adaptation works must be highlighted and approved in advance.

c. Design a modular GRP water storage tank, ensuring the design and materials conform to the following standards:

1. AWWA D103-09 – Bolted water storage tank construction,

2. AWWA Standard 652-02 – Disinfection of water-storage facilities

3. ISO 1461 – Hot-dip galvanized steel components,

4. IBC and ASCE 7 – Seismic and structural design requirements,

5. NSF/ANSI 61 – Materials suitable for potable water applications,

6. OBO Design and Construction Standards – For overseas U.S. Government facilities.

7. EM 385-1-1 – Safety

8. Submit shop drawings and manufacturer datasheets for review and approval by the Contracting Officer’s Representative (COR) prior to fabrication and procurement.

9. Plan and coordinate staged assembly within the mechanical room space.

10. Ensure the tank design incorporates access hatches, overflow and drain connections, inlet/outlet ports, and provisions for sensor connections.

11. The rough available installation pad space within the mechanical room has been estimated at approximately 2.67 meters in length, 2.64 meters in width, contractor is responsible and shall filed verify all dimensions.

12. The existing pad shall be extended as needed as part of this contract to optimize tank capacity using standard size panels for maintenance and replacement.

13. The contractor shall design and fabricate a modular Glass-Reinforced Plastic (GRP) water storage tank, constructed from sectional panels and fully insulated with injected urethane foam, to maximize the use of the available space while meeting all structural and operational requirements.

14. The nominal capacity of the tank shall be no less than 18,000 liters (approximately 4,755 gallons). However, the contractor shall be required to propose the maximum achievable tank capacity based on the available space constraints and applicable structural requirements.

15. Maximum allowable continuous temperature for storage tank shall be at least 60c.

16. The modular GRP panels must be assembled using gaskets and fasteners that guarantee a seamless and leak-proof seal, in accordance with AWWA D103 standards. All penetrations for inlets, outlets, overflow, and sensors shall also be watertight.

17. The tank shall include an observable liquid level system (with graduations for example, markings at 25%, 50%, 75%, 100% so operators can easily read the water level).

18. An OSHA-compliant access ladder system shall also be included.

19. The contractor shall design and install a new seismic restraint system that complies with applicable seismic standards, including IBC and ASCE 7. The system shall ensure the structural stability of the modular GRP tank during seismic events.

20. All tank connections must have adequate provisions for tank expansion, contraction due to temperature and load change. This provision should allow minimum 4%-dimensional movement.

21. Provide and install Flexmaster expansion joint for all tank fittings and connections.

22. All required piping, fittings etc. for this project shall be CPVC.

23. Expansion joints are not designed to make up for piping misalignment error. Pipe misalignment should be no more than ¼” in any direction.

24. Piping must be supported in all directions, so expansion joints do not carry any piping weight.

25. Isolation valves will be installed on each line. Provide and install ¼ turn ball valves rated for domestic water use.

26. A union or flange connection between lines and tank is required to insure all lines to tank can be easily removed from the tank.

27. The modular tank must be assembled in strict accordance with the manufacturer’s installation manuals and guidelines.

28. All structural elements, including bolts, gaskets, and sealants, must comply with the manufacturer's standards.

29. Provide spares: 1 new type panel section including all gaskets and all hardware for repair

2. Foundation and Pad Preparation

a. The contractor shall conduct a thorough inspection of the existing concrete foundation and pad during the initial site visit to confirm that it meets the GRP tank manufacturer’s load-bearing and leveling requirements, as well as applicable structural standards.

b. Any damage, deterioration, or irregularities observed—such as cracks, surface spalling, or unevenness—that could affect the proper installation, alignment, or long-term structural stability of the new modular tank must be clearly identified and documented and corrected as part of this installation scope.

c. Based on the findings of the site survey, the contractor shall include all required corrective actions in the initial technical and financial proposal submitted under this contract. The proposed solution must be reflected as part of the fixed-price offer.

d. All repairs shall be subject to review and written approval by the Contracting Officer’s Representative (COR) prior to execution.

e. The foundation must be cleaned and properly prepared before installation, ensuring a level, stable, and debris-free surface.

f. Patching: Apply high-strength, non-shrink, cementitious repair mortar (e.g., SikaTop 123 or equivalent) in all damaged areas. Where reinforcement has been lost, and to ensure adhesion, insert new reinforcement. Ensure patching compound is compatible with epoxy topcoats.

g. Primer Coat: Apply an epoxy-based primer that ensures bonding with the substrate (such as Sikafloor®-156 or equivalent).

h. Topcoat: Apply a minimum two-layer chemical-resistant epoxy coating designed for water treatment facilities. Sikafloor-264, or equivalent. Total dry film thickness should meet manufacturer specifications.

3. Overflow and Low-Level Sensors

a. As part of the installation scope, the contractor shall furnish and install a complete sensor system to monitor overflow and low water levels in the GRP water storage tank. The system shall include a high-level (overflow) sensor and a low-level switch to support both normal operations and early detection of abnormal water levels.

These sensors must be compatible with the existing building automation system (BAS) or function independently with a local annunciator, as specified during the design review.

b. The contractor shall supply and install all required components, including but not limited to:

1. High-level float or ultrasonic sensor for overflow detection

2. Low-level switch for minimum water level monitoring

3. Signal relays or controllers (as applicable)

4. All cabling, conduits, junction boxes, and termination hardware

5. Weatherproof housings, brackets, and mounting accessories

6. Connection to the main tank control panel or local control box

7. Integration with existing or new alarm/monitoring interface

c. The system must include factory calibration and on-site verification tests to ensure reliable operation. Installation shall conform to OBO electrical and safety standards, and the system shall be labeled and documented as part of the as-built submission. The contractor is fully responsible for coordinating electrical connections, power requirements, and all interface components necessary for a fully functional and operational level monitoring system.

4. Corrosion Protection:

a. All metallic components, including structural steel, fasteners, supports, piping, and accessories, shall be corrosion-protected in accordance with U.S. Department of State OBO standards and specifications, particularly OBO Building Code (OBO/PE/DE/CE) and the Design Standards for Overseas Facilities (DSOF).

b. Ferrous metals shall be hot-dip galvanized after fabrication in accordance with ISO 1461:2022 and ASTM A123/A123M – Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products. Bolts and fasteners shall comply with ASTM A153 or ISO 1461, and stainless-steel fasteners shall meet ASTM F593 or ISO 3506.

c. Surface preparation shall conform to SSPC-SP 6/NACE No. 3 – Commercial Blast Cleaning prior to galvanizing or painting. Painting systems shall be selected based on exposure conditions per ISO 12944 and SSPC Paint Application Specifications, with a minimum corrosion category of C4 or C5 in marine or industrial environments.

d. All stainless-steel components shall be AISI 316L or higher, particularly for use in corrosive or marine environments. Care shall be taken to prevent galvanic corrosion by isolating dissimilar metals using appropriate insulating gaskets, sleeves, or coatings.

5. Design Submittal Requirements

The contractor shall submit the following documentation to the Contracting Officer (CO) and Contracting Officer’s Representative (COR) within 28 calendar days of the Notice to Proceed (NTP), unless otherwise stated. All plans shall be reviewed and approved prior to any material procurement or execution of work.

a. Submittal Schedule

b. Critical Path Method (CPM) Schedule, including design milestones, fabrication, delivery, and installation. Clearly show any anticipated water outages for coordination with the embassy.

c. Preliminary Design Drawings

d. Final Design Drawings

i. GRP tank configuration, dimensions, and components

ii. Location and layout of piping, access, hatches, ladders, and safety systems, etc.

ii. Structural Analysis and Calculations

iii. Seismic and load-bearing analysis in accordance with IBC and ASCE 7

iv. Code and Standards Compliance Statement

e. Shop Drawings & Technical Datasheets

f. Modular GRP tank panels

g. Insulation materials (urethane-injected foam)

h. Piping, fittings, valves, and accessories

i. Expansion joints (e.g., Flexmaster)

j. Level sensors and instrumentation

6. IMPLENTATION AND COMMISIONING

a. Disassemble, disconnect, and remove existing damaged tank. The contractor shall carefully disassemble, disconnect, and remove the existing damaged water storage tank currently located within the water treatment facility.

b. Prior to any removal activities, the contractor shall isolate and depressurize all associated piping, valves, and connections to ensure safe working conditions. All electrical, mechanical, and plumbing connections to the existing tank must be safely disconnected and properly terminated or prepared for reconnection to the new system. The tank shall be dismantled in a manner that minimizes disruption to surrounding systems and infrastructure. All removed components, including associated support structures and accessories deemed non-reusable or obsolete, shall be considered the property of the contractor and must be disposed of off-site in compliance with local environmental and safety regulations. The contractor is responsible for ensuring that the disassembly does not damage adjacent equipment or structures, should any damage occur as a result of the contractor’s activities, it shall be the contractor’s sole responsibility to repair or replace the affected items at no additional cost to the Government. and shall restore the work area to a clean and safe condition upon completion.

c. Contractor is responsible for replacing any broken or damaged items damaged by this Contractor during this work.

d. Disinfection of water storage tanks is required before putting into service per AWWA Standard 652-02.

e. A final written report detailing work done to test and commissioning of equipment.

f. Two sets of O&M manuals shall be provided to the COR prior to demobilization, O&M manuals must include all schematics, parameter settings that may be needed in the maintenance or troubleshooting of the system and equipment.

7. Documentation and Inspection:

Submit full installation checklists, inspection documentation, and test results for approval. Final inspection will be conducted by the COR and the CO.

8. Security

i. A list of employees who will work on this project, to include names (as shown on ID), and ID numbers must be submitted to the COR within one (1) week of the Notice to Proceed (NTP).

ii. Information on any vehicles which must come onto the Embassy Compound as part of this work must be submitted to the COR. This information is to include VIN number, license plate number, vehicle description, and color and must be submitted to the COR within one (1) week of the NTP.

9. Tools

i. All tools must be provided by the contractor.

ii. All tools must be taken off-site every day or stored in a locked container each day.

10. Contractor Key Personnel Technical Qualifications

Resumes for all proposed personnel detailing their experience MUST be submitted with the Technical Proposal to be considered.

Qualified Electrical Labor

a. All personnel used in the performance of the electrical work shall qualified electricians.

b. At least one team member must have 10 or more years of applicable electrical experience.

Qualified Mechanical Labor

c. All contractor-provided mechanical installation labor furnished under this task order for the mechanical/piping tasks shall be journeyman and master level tradespersons

Trade Licenses

d. Any professional tradesmen licenses if required for Contractor personnel shall be current and valid at the time of COR review and shall be maintained and remain current and valid for the complete duration of the project execution.

Use of Non-Licensed Labor

e. Contractor use of non-licensed electrical laborers, helpers, etc. to execute, plan, lay out, or otherwise direct the execution of the electrical work activities under this order is not allowed.

11. Safety

a. Contractor must submit, a Company Safety Plan including a specific Safety Plan tailored to this project to include an Activity Hazard Analysis (AHA).

b. All safety plans must comply with the EM 385-1-1 Safety and Health Requirements Manual, as well as the safety standards and guidelines established by the Office of Overseas Buildings Operations (OBO), U.S. Department of State

c. General. The contractor shall provide and maintain work environments and procedures which will safeguard the public and Government personnel, property, materials, supplies, and equipment exposed to contractor operations and activities; avoid interruptions of Government operations and delays in project completion dates and control costs in the performance of this contract. For these purposes, the contractor shall:

i. Comply with the standards issued by any local government authority having jurisdiction over occupational health and safety issues; and,

1. Temporary wiring, use of portable electric tools, or other recognized electrical hazards. Temporary wiring and portable electric tools require the use of a ground fault circuit interrupter (GFCI) in the affected circuits; other electrical hazards may also require the use of a GFCI.

2. Work in confined spaces (limited exits, potential for oxygen less than 19.5 percent or combustible atmosphere, potential for solid or liquid engulfment, or other hazards considered to be immediately dangerous to life or health such as water tanks, transformer vaults, sewers, cisterns, etc.);

3. Hazardous materials—a material with a physical or health hazard including but not limited to, flammable, explosive, corrosive, toxic, reactive or unstable, or any operations which creates any kind of contamination inside an occupied building such as dust from demolition activities, paints, solvents, etc.; or

4. Hazardous noise levels.

5. Subcontracts. The contractor shall be responsible for its subcontractors' compliance with this clause.

6. Written program. Before commencing work, the contractor shall:

7. Submit a written safety plan to the contracting officer for implementing this clause. The plan shall include specific management or technical procedures for effectively controlling hazards associated with the project; and,

8. Meet with the contracting officer to discuss and develop a mutual understanding relative to administration of the overall safety program.

9. Notification. The contracting officer shall notify the contractor of any non-compliance with these requirements and the corrective actions required.

This notice, when delivered to the contractor or the contractor's representative on site, shall be deemed sufficient notice of the non-compliance and corrective action required. After receiving the notice, the contractor shall immediately take corrective action. If the contractor fails or refuses to promptly take corrective action, the contracting officer may issue an order suspending all or part of the work until satisfactory corrective action has been taken. The contractor shall not be entitled to any equitable adjustment of the contract price or extension of the performance schedule on any suspension of work order issued under this clause.

12. Warranty

a. The contractor shall provide a one-year complete coverage warranty that includes all parts, materials, labor, travel costs, per diem, and all miscellaneous costs.

b. The contractor may seek reimbursement from the manufacturer or any other entity providing warranties for the equipment installed, but the contractor must be the responsible party for warranty repairs.

c. The contractor shall provide, AS PART OF THE WARRANTY a technician for onsite repairs within 72 hours of notification of an operational problem or failure within the warranty period.

SECTION 2 - CONTRACT CLAUSES

FAR 52.212-5 Contract Terms and Conditions Required to Implement Statutes or Executive Orders—Commercial Products and Commercial Services (JAN 2025)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (Jan 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab Covered Entities (Dec 2023) (Section 1634 of Pub. L. 115-91).

(3) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (Nov 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(4) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (Nov 2015).

(5) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (Mar 2023) ( 31 U.S.C. 3903 and 10 U.S.C. 3801).

(6) 52.233-3, Protest After Award (Aug 1996) (31 U.S.C. 3553).

(7) 52.233-4, Applicable Law for Breach of Contract Claim (Oct 2004) (Public Laws 108-77 and 108-78 ( 19 U.S.C. 3805 note)).

(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

__ (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (Jun 2020), with Alternate I (Nov 2021) (41 U.S.C. 4704 and 10 U.S.C. 4655).

__ (2) 52.203-13, Contractor Code of Business Ethics and Conduct (Nov 2021) (41 U.S.C. 3509)).

__ (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (Jun 2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.)

__ (4) 52.203-17, Contractor Employee Whistleblower Rights (Nov 2023) ( 41 U.S.C. 4712); this clause does not apply to contracts of DoD, NASA, the Coast Guard, or applicable elements of the intelligence community—see FAR 3.900(a).

_X_ (5) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (Jun 2020) (Pub. L. 109-282) ( 31 U.S.C. 6101 note).

__ (6) [Reserved].

__ (7) 52.204-14, Service Contract Reporting Requirements (Oct 2016) (Pub. L. 111-117, section 743 of Div. C).

__ (8) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (Oct 2016) (Pub. L. 111-117, section 743 of Div. C).

_X_ (9) 52.204-27, Prohibition on a ByteDance Covered Application (Jun 2023) (Section 102 of Division R of Pub. L. 117-328).

__ (10) 52.204-28, Federal Acquisition Supply Chain Security Act Orders—Federal Supply Schedules, Governmentwide Acquisition Contracts, and Multi-Agency Contracts. (Dec 2023) ( Pub. L. 115–390, title II).

https://www.acquisition.gov/far/52.203-19#FAR_52_203_19 https://www.acquisition.gov/far/52.204-23#FAR_52_204_23 https://www.acquisition.gov/far/52.204-25#FAR_52_204_25 https://www.acquisition.gov/far/52.209-10#FAR_52_209_10 https://www.acquisition.gov/far/52.232-40#FAR_52_232_40 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section3903&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section3903&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title10-section3801&num=0&edition=prelim https://www.acquisition.gov/far/52.233-3#FAR_52_233_3 https://www.acquisition.gov/far/52.233-4#FAR_52_233_4 https://www.acquisition.gov/far/52.203-6#FAR_52_203_6 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title10-section4655&num=0&edition=prelim https://www.acquisition.gov/far/52.203-13#FAR_52_203_13 https://www.acquisition.gov/far/52.203-15#FAR_52_203_15 https://www.acquisition.gov/far/52.203-17#FAR_52_203_17 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title41-section4712&num=0&edition=prelim https://www.acquisition.gov/far/3.900#FAR_3_900 https://www.acquisition.gov/far/52.204-10#FAR_52_204_10 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title31-section6101&num=0&edition=prelim https://www.acquisition.gov/far/52.204-14#FAR_52_204_14 https://www.acquisition.gov/far/52.204-15#FAR_52_204_15 https://www.acquisition.gov/far/52.204-27#FAR_52_204_27 https://www.acquisition.gov/far/52.204-28#FAR_52_204_28 https://www.govinfo.gov/link/plaw/115/public/390

__ (11)

(i) 52.204-30, Federal Acquisition Supply Chain Security Act Orders—Prohibition. (Dec 2023) ( Pub. L. 115–390, title II).

__ (ii) Alternate I (Dec 2023) of 52.204-30.

_X_ (12) 52.209-6, Protecting the Government's Interest When Subcontracting With Contractors Debarred, Suspended, Proposed for Debarment, or Voluntarily Excluded. (Jan 2025) ( 31 U.S.C. 6101 note).

__ (13) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (Oct 2018) ( 41 U.S.C. 2313).

__ (14) [Reserved].

__ (15) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (Oct 2022) ( 15 U.S.C. 657a).

__ (16) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (Oct 2022) (if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a).

__ (17) [Reserved] __ (18)

(i) 52.219-6, Notice of Total Small Business Set-Aside (Nov 2020) (15 U.S.C. 644).

__ (ii) Alternate I (Mar 2020) of 52.219-6.

__ (19)

(i) 52.219-7, Notice of Partial Small Business Set-Aside (Nov 2020) (15 U.S.C. 644).

__ (ii) Alternate I (Mar 2020) of 52.219-7.

__ (20) 52.219-8, Utilization of Small Business Concerns (Jan 2025)( 15 U.S.C. 637(d)(2) and (3)).

__ (21)

(i) 52.219-9, Small Business Subcontracting Plan (Jan 2025) ( 15 U.S.C. 637(d)(4)).

__ (ii) Alternate I (Nov 2016) of 52.219-9.

__ (iii) Alternate II (Nov 2016) of 52.219-9.

__ (iv) Alternate III (Jun 2020) of 52.219-9.

__ (v) Alternate IV (Jan 2025) of 52.219-9.

__ (22)

(i) 52.219-13, Notice of Set-Aside of Orders (Mar 2020) (15 U.S.C. 644(r)).

__ (ii) Alternate I (Mar 2020) of 52.219-13.

__ (23) 52.219-14, Limitations on Subcontracting (Oct 2022) (15 U.S.C. 657s).

__ (24) 52.219-16, Liquidated Damages—Subcontracting Plan (Sep 2021) (15 U.S.C. 637(d)(4)(F)(i)).

__ (25) 52.219-27, Notice of Set-Aside for, or Sole-Source Award to, Service-Disabled Veteran- Owned Small Business (SDVOSB) Concerns Eligible Under the SDVOSB Program (Feb 2024) (15 U.S.C. 657f).

__ (26)

(i) 52.219-28, Postaward Small Business Program Representation (Jan 2025) (15 U.S.C. 632(a)(2)).

__ (ii) Alternate I (Mar 2020) of 52.219-28.

__ (27) 52.219-29, Notice of Set-Aside for, or Sole-Source Award to, Economically Disadvantaged Women-Owned Small Business Concerns (Oct 2022) (15 U.S.C. 637(m)).

__ (28) 52.219-30, Notice of Set-Aside for, or Sole-Source Award to, Women-Owned Small Business Concerns Eligible Under the Women-Owned Small Business Program (Oct 2022) (15 U.S.C. 637(m)).

https://www.acquisition.gov/far/52.204-30#FAR_52_204_30 https://www.govinfo.gov/link/plaw/115/public/390 https://www.acquisition.gov/far/52.204-30#FAR_52_204_30 https://www.acquisition.gov/far/52.209-6#FAR_52_209_6 https://www.govinfo.gov/link/uscode/31/6101 https://www.acquisition.gov/far/52.209-9#FAR_52_209_9 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title41-section2313&num=0&edition=prelim https://www.acquisition.gov/far/52.219-3#FAR_52_219_3 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637a&num=0&edition=prelim https://www.acquisition.gov/far/52.219-4#FAR_52_219_4 https://www.acquisition.gov/far/52.219-6#FAR_52_219_6 https://www.acquisition.gov/far/52.219-6#FAR_52_219_6 https://www.acquisition.gov/far/52.219-7#FAR_52_219_7 https://www.acquisition.gov/far/52.219-7#FAR_52_219_7 https://www.acquisition.gov/far/52.219-8#FAR_52_219_8 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637&num=0&edition=prelim https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637&num=0&edition=prelim https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-9#FAR_52_219_9 https://www.acquisition.gov/far/52.219-13#FAR_52_219_13 https://www.acquisition.gov/far/52.219-13#FAR_52_219_13 https://www.acquisition.gov/far/52.219-14#FAR_52_219_14 https://www.acquisition.gov/far/52.219-16#FAR_52_219_16 https://www.acquisition.gov/far/52.219-27#FAR_52_219_27 https://www.acquisition.gov/far/52.219-28#FAR_52_219_28 https://www.acquisition.gov/far/52.219-28#FAR_52_219_28 https://www.acquisition.gov/far/52.219-29#FAR_52_219_29 https://www.acquisition.gov/far/52.219-30#FAR_52_219_30

__ (29) 52.219-32, Orders Issued Directly Under Small Business Reserves (Mar 2020) ( 15 U.S.C. 644(r)).

__ (30) 52.219-33, Nonmanufacturer Rule (Sep 2021) ( 15 U.S.C. 637(a)(17)).

__ (31) 52.222-3, Convict Labor (Jun 2003) (E.O.11755).

_X_ (32) 52.222-19, Child Labor—Cooperation with Authorities and Remedies (Jan 2025)( E.O.

13126).

__ (33) 52.222-21, Prohibition of Segregated Facilities (Apr 2015).

__ (34)

(i) 52.222-26, Equal Opportunity (Sep 2016) (E.O.11246).

__ (ii) Alternate I (Feb 1999) of 52.222-26.

__ (35)

(i) 52.222-35, Equal Opportunity for Veterans (Jun 2020) ( 38 U.S.C. 4212).

__ (ii) Alternate I (Jul 2014) of 52.222-35.

__ (36)

(i) 52.222-36, Equal Opportunity for Workers with Disabilities (Jun 2020) ( 29 U.S.C. 793).

__ (ii) Alternate I (Jul 2014) of 52.222-36.

_X_ (37) 52.222-37, Employment Reports on Veterans (Jun 2020) ( 38 U.S.C. 4212).

__ (38) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496).

_X_ (39)

(i) 52.222-50, Combating Trafficking in Persons (Nov 2021) (22 U.S.C. chapter 78 and E.O.

13627).

__ (ii) Alternate I (Mar 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).

_X_ (40) 52.222-54, Employment Eligibility Verification (Jan 2025) ( Executive Order 12989).

(Not applicable to the acquisition of commercially available off-the-shelf items or certain other types of commercial products or commercial services as prescribed in FAR 22.1803.)

__ (41)

(i) 52.223-9, Estimate of Percentage of Recovered Material Content for EPA–Designated Items (May 2008) ( 42 U.S.C. 6962(c)(3)(A)(ii)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

__ (ii) Alternate I (May 2008) of 52.223-9 (42 U.S.C. 6962(i)(2)(C)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

__ (42) 52.223-11, Ozone-Depleting Substances and High Global Warming Potential Hydrofluorocarbons (May 2024) ( 42 U.S.C. 7671, et seq.).

__ (43) 52.223-12, Maintenance, Service, Repair, or Disposal of Refrigeration Equipment and Air Conditioners (May 2024) ( 42 U.S.C. 7671, et seq.).

__ (44) 52.223-20, Aerosols (May 2024) ( 42 U.S.C. 7671, et seq.).

__ (45) 52.223-21, Foams (May 2024) ( 42 U.S.C. 7671, et seq.).

__ (46) 52.223-23, Sustainable Products and Services (May 2024) ( E.O. 14057, 7 U.S.C.

8102, 42 U.S.C. 6962, 42 U.S.C. 8259b, and 42 U.S.C. 7671l).

__ (47)

(i) 52.224-3 Privacy Training (Jan 2017) ( 5 U.S.C. 552 a).

__ (ii) Alternate I (Jan 2017) of 52.224-3.

__ (48)

(i) 52.225-1, Buy American-Supplies (Oct 2022) (41 U.S.C. chapter 83).

__ (ii) Alternate I (Oct 2022) of 52.225-1.

__ (49)

(i) 52.225-3, Buy American-Free Trade Agreements-Israeli Trade Act (NOV 2023) ( 19 U.S.C.

3301 note, 19 U.S.C. 2112 note, 19 U.S.C. 3805 note, 19 U.S.C. 4001 note, 19 U.S.C. chapter https://www.acquisition.gov/far/52.219-32#FAR_52_219_32 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section644&num=0&edition=prelim https://www.acquisition.gov/far/52.219-33#FAR_52_219_33 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title15-section637&num=0&edition=prelim https://www.acquisition.gov/far/52.222-3#FAR_52_222_3 https://www.acquisition.gov/far/52.222-19#FAR_52_222_19 https://www.federalregister.gov/executive-order/13126 https://www.federalregister.gov/executive-order/13126 https://www.acquisition.gov/far/52.222-21#FAR_52_222_21 https://www.acquisition.gov/far/52.222-26#FAR_52_222_26 https://www.acquisition.gov/far/52.222-26#FAR_52_222_26 https://www.acquisition.gov/far/52.222-35#FAR_52_222_35 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title38-section4212&num=0&edition=prelim https://www.acquisition.gov/far/52.222-35#FAR_52_222_35 https://www.acquisition.gov/far/52.222-36#FAR_52_222_36 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title29-section793&num=0&edition=prelim https://www.acquisition.gov/far/52.222-36#FAR_52_222_36 https://www.acquisition.gov/far/52.222-37#FAR_52_222_37 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title38-section4212&num=0&edition=prelim https://www.acquisition.gov/far/52.222-40#FAR_52_222_40 https://www.acquisition.gov/far/52.222-50#FAR_52_222_50 https://www.acquisition.gov/far/52.222-50#FAR_52_222_50 https://www.acquisition.gov/far/52.222-54#FAR_52_222_54 https://www.federalregister.gov/executive-order/12989 https://www.acquisition.gov/far/22.1803#FAR_22_1803 https://www.acquisition.gov/far/52.223-9#FAR_52_223_9 https://www.acquisition.gov/far/52.223-9#FAR_52_223_9 https://www.acquisition.gov/far/52.223-11#FAR_52_223_11 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section7671&num=0&edition=prelim https://www.acquisition.gov/far/52.223-12#FAR_52_223_12 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section7671&num=0&edition=prelim https://www.acquisition.gov/far/52.223-20#FAR_52_223_20 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section7671&num=0&edition=prelim https://www.acquisition.gov/far/52.223-21#FAR_52_223_21 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section7671&num=0&edition=prelim https://www.acquisition.gov/far/52.223-23#FAR_52_223_23 https://www.federalregister.gov/executive-order/14057 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title7-section8102&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title7-section8102&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section6962&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section8259&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title42-section7671&num=0&edition=prelim https://www.acquisition.gov/far/52.224-3#FAR_52_224_3 http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title5-section552&num=0&edition=prelim https://www.acquisition.gov/far/52.224-3#FAR_52_224_3 https://www.acquisition.gov/far/52.225-1#FAR_52_225_1 https://www.acquisition.gov/far/52.225-1#FAR_52_225_1 https://www.acquisition.gov/far/52.225-3#FAR_52_225_3 https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section3301&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section3301&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section2112&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section3805&num=0&edition=prelim https://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title19-section4001&num=0&edition=prelim http://uscode.house.gov/view.xhtml?req=granuleid%3AUSC-prelim-title19-chapter29&saved=%7CZ3JhbnVsZWlkOlVTQy1wcmVsaW0tdGl0bGU0MC1jaGFwdGVyMzctZnJvbnQ%3D%7C%7C%7C0%7Cfalse%7Cprelim&edition=prelim

29 (sections 4501-4732), Public Law 103-182, 108-77, 108-78, 108-286, 108-302, 109-53, 109- 169, 109-283, 110-138, 112-41, 112-42, and 112-43.

__ (ii) Alternate I [Reserved].

__ (iii) Alternate II (Jan 2025) of 52.225-3.

__ (iv) Alternate III (Feb 2024) of 52.225-3.

__ (v) Alternate IV (Oct 2022) of 52.225-3.

__ (50) 52.225-5, Trade Agreements (NOV 2023) ( 19 U.S.C. 2501, et seq., 19 U.S.C. 3301 note).

_X_ (51) 52.225-13, Restrictions on Certain Foreign Purchases (Feb 2021) (E.O.’s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury).

__ (52) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Oct 2016) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. Subtitle A, Part V, Subpart G Note).

__ (53) 52.226-4, Notice of Disaster or Emergency Area Set-Aside (Nov 2007) (42 U.S.C. 5150).

__ (54) 52.226-5, Restrictions on Subcontracting Outside Disaster or Emergency Area (Nov 2007) (42 U.S.C. 5150).

_X_ (55) 52.226-8, Encouraging Contractor Policies to Ban Text Messaging While Driving (May 2024) ( E.O. 13513).

__ (56) 52.229-12, Tax on Certain Foreign Procurements (Feb 2021).

_X_ (57) 52.232-29, Terms for Financing of Purchases of Commercial Products and Commercial Services (Nov 2021) (41 U.S.C. 4505, 10 U.S.C. 3805).

__ (58) 52.232-30, Installment Payments for Commercial Products and Commercial Services (Nov 2021) (41 U.S.C. 4505, 10 U.S.C. 3805).

_X_ (59) 52.232-33, Payment by Electronic Funds Transfer-System for Award Management (Oct2018) ( 31 U.S.C. 3332).

__ (60) 52.232-34, Payment by Electronic Funds Transfer-Other than System for Award Management (Jul 2013) (31 U.S.C. 3332).

__ (61) 52.232-36, Payment by Third Party (May 2014) (31 U.S.C. 3332).

__ (62) 52.239-1, Privacy or Security Safeguards (Aug 1996) ( 5 U.S.C. 552a).

_X_ (63) 52.240-1, Prohibition on Unmanned Aircraft Systems Manufactured or Assembled by American Security Drone Act-Covered Foreign Entities (Nov 2024) (Sections 1821-1826, Pub. L.

118-31, 41 U.S.C. 3901 note prec.).

__ (64) 52.242-5, Payments to Small Business Subcontractors (Jan 2017) (15 U.S.C. 637(d)(13)).

__ (65)

(i) 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (Nov 2021) ( 46 U.S.C. 55305 and 10 U.S.C. 2631).

__ (ii) Alternate I (Apr 2003) of 52.247-64.

__ (iii) Alternate II (Nov 2021) of 52.247-64.

(c) The Contractor shall comply with the FAR clauses in this paragraph (c), applicable to commercial services, that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

[Contracting Officer check as appropriate.] __ (1) 52.222-41, Service Contract Labor Standards (Aug 2018) (41 U.S.C. chapter67).

__ (2) 52.222-42, Statement of Equivalent Rates for Federal Hires (May 2014) (29 U.S.C.