RFQ # 1457- Attachment 1 - Admin. Info - Custom Built Headache Racks.pdf

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 1 of 14

IDAHO DEPARTMENT OF FISH & GAME

ATTACHMENT 1 – SECTION 1

AMENDMENT TWO

RFQ Title: Custom Built Headache Racks

RFQ Number: RFQ # 1457

RFQ Solicitation Contact: Dana Jo McGee, Buyer DanaJo.McGee@idfg.idaho.gov 208-287-2816

Submit Electronically via IPRO: Supplier Portal / Supplier Portal (inforgov.com)

Deadline to Receive Questions: See IPRO

RFQ Closing Date: See IPRO

Award: Award will be made, all or none, to the responsive responsible vendor with the lowest Total Cost.

A. Purpose The Idaho Department of Fish & Game (IDFG) is requesting quotes from qualified vendors for the purchase and delivery of eighteen

(18) Custom Built Headache Racks as further detailed below.

B. General Information & Solicitation Instructions This Solicitation is issued by IDFG via IPRO - Supplier Portal / Supplier Portal (inforgov.com) The RFQ Lead is the only contact for this Solicitation. All correspondence regarding this RFQ must be in writing. In the event that it becomes necessary to revise any part of this RFQ, amendments will be posted at IPRO. It is the responsibility of the Bidder to monitor IPRO for any updates or amendments. Any oral interpretations or clarifications of this RFQ will not be relied upon. All changes to this RFQ must be in writing and posted in IPRO to be valid. Alternate Bids are not allowed.

C. Submission Requirements Your response to this RFQ may be submitted electronically via IPRO or email. IDFG will not be accepting manual submissions for this solicitation. Your submission must include the Required Submittals listed below and be received prior to the deadline noted below.

Failure to provide any of the documents or submission on a form different from those provided, may cause your submission to be found as non-responsive.

Electronic Submission:

IPRO – Enter your pricing in IPRO- Supplier Portal / Supplier Portal (inforgov.com)` . and upload all Required Submittals.

When a Bidder has successfully submitted a response to IPRO, the Bidder should see a change in the system from “Draft Bid” (see Fig. 1) to “Submission confirmation email sent” (see Fig. 2). Bidders are encouraged to document notification of successful submission for their records. If you believe you have submitted your Bid, but have not received the “Bid Submitted” message, you are advised to contact the IPRO provider’s help desk (phone number available at https://purchasing.idaho.gov/ipro.html) and notify the solicitation lead prior to the solicitation End Time. Vendors are strongly encouraged to begin the process of submitting the response far enough in advance of the End Time to allow for resolution of technical difficulties. Be advised that the State is not responsible for a Vendor’s failure to timely submit a responsive submission due to any technical or technological difficulties. See

IDAPA 38.05.01.61.02.

https://sms-idaho-prd.tam.inforgov.com/fsm/SupplyManagementSupplier/page/XiSupplyManagementSupplierPage?csk.SupplierGroup=LUMA https://sms-idaho-prd.tam.inforgov.com/fsm/SupplyManagementSupplier/page/XiSupplyManagementSupplierPage?csk.SupplierGroup=LUMA https://sms-idaho-prd.tam.inforgov.com/fsm/SupplyManagementSupplier/page/XiSupplyManagementSupplierPage?csk.SupplierGroup=LUMA https://purchasing.idaho.gov/ipro.html

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 2 of 14

Fig. 1

Fig. 2

If submitting via IPRO, be advised that that the Offeror for Proposal evaluation and award purposes is the entity profile under which the Proposal is submitted in IPRO, which must be the same legal entity presented in the uploaded response materials. If the entity identified on the state supplied Signature Page differs from the entity under which you submit your Proposal in IPRO, the information provided on the Signature Page prevails.

While it is not mandatory to submit your Proposal electronically via IPRO, all Offerors participating in a Solicitation issued through IPRO must establish an account in the IPRO system (even if submitting a Proposal manually outside of IPRO) as it is necessary in order to process and/or award the resulting Contract(s). Establishing an account is free and only takes a few minutes.

Offerors are further advised to upload response materials with descriptive file names, organized and consolidated in a manner which allows evaluators to efficiently navigate the Offeror’s response; as the State will print uploaded documents for evaluation in the manner received via IPRO

Email:

Send an email to the Solicitation Contact (listed above) and attach all Required Submittals.

D. Required Submittals As part of your response to this RFQ, the following documents are required.

Attachment 2 – Price Sheet Attachment 3 – Signature Page Attachment 4 – Certificate of Insurance

E. Award Award may be all to one or by line item (if applicable) to the responsive responsible Bidder with the lowest fully burdened cost, as provided on the Price Sheet in IPRO, as determined to be in the best interest of the State.

F. Resulting Contract If IDFG awards a contract from this Solicitation, it will do so by issuing a Purchase Order (PO) document, which will be an acceptance of the successful bid. The PO will be comprised of the following documents; this RFQ, including any incorporated documents; the successful bid, including any clarifications requested by IDFG; and an artifact formalizing any requirements agreed upon through Contract discussions or negotiations, if applicable.

The following documents are incorporated into this RFQ as if set out in their entirety:

Solicitation Instructions for Vendors – January 2017 State of Idaho Standard Contract Terms and Conditions – July 2026

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 3 of 14

The documents may be found on the “Information for Vendors” page of the State’s Division of Purchasing (DOP) website (https://purchasing.idaho.gov/laws-and-policies/). If multiple versions of any of these documents are available on the website, the version in effect on the day the RFQ is issued shall apply.

ATTACHMENT 1 – SECTION 2

The following special terms and conditions are incorporated into the resulting Contract to supplement or add to the State of Idaho Standard Contract Terms and Conditions.

A. Delivery Contractor must be located within seventy-five (75) miles of the location listed below, Contractor will pick up the vehicle and take it to the Contractor’s installation facility. Installation of the Racks and returning of the vehicle must be completed within thirty (30) calendar days once the Contractor has taken possession of the vehicle.

Pickup & delivery must be made Monday through Thursday, 8:00 am to 4:00 pm local time excluding state of Idaho recognized holidays (https://www.idaho.gov/government/holidays.html), unless otherwise approved in writing by IDFG. Contractor must notify IDFG, in writing, no less than seven (7) business days prior to delivery. IDFG delivery contact information will be provided upon Award.

Delivery Location Idaho Department of Fish and Game

15950 N Gate Blvd Nampa, ID 83687

B. Acceptance Upon receipt of the Custom Built Headache Racks, per the delivery location, the Custom Built Headache Racks will be inspected by the delivery contact (or approved designee) to ensure the requirements and specifications are met. The Acceptance period will be for thirty (30) calendar days from the date the Custom Built Headache Racks are delivered.

In the event the specifications are not met, the Contractor must pick-up, correct any discrepancies, and re-deliver within thirty (30) calendar days after notification from IDFG, at no additional cost to IDFG. In the event that the Custom Built Headache Racks do not meet the specifications or is found with discrepancies that are not fixed by the Contractor during the Acceptance period, IDFG reserves the right to reject the Custom Built Headache Racks via official notification.

If approved by IDFG, the Contractor may correct discrepancies on-site at IDFG’s location in lieu of pick-up and return shipping. The Contractor will be responsible for providing all labor; tools, parts, supplies, and worksite clean up to make any necessary corrections.

The timeframe for corrective action will still be as identified above.

C. Invoicing & Payments Invoices – Invoices must be submitted as further detailed below. Invoices submitted prior to Acceptance, or without the required information listed below, will be returned to the Contractor for correction and resubmission.

Invoices must include the following information:

• Contractor Company Name & Contact Information

• Contract Name & Number (PO #)

• Invoice Number & Date

• Itemization of the purchased goods to include: description matching the contract, quantity, unit of measure, unit price, extended price, and total invoiced amount.

Payments – Payment for correctly submitted invoices will be made in accordance with Idaho Code 67-2302:

https://legislature.idaho.gov/statutesrules/idstat/title67/t67ch23/sect67-2302/

D. Warranty Warranty must be for a minimum period of one (1) year, for the entire Custom Built Headache Racks, after Acceptance. Warranty must include all tools, parts, equipment, labor, and freight to repair or replace a defective warrantied item, which may include the entire Custom Built Headache Racks.

https://purchasing.idaho.gov/laws-and-policies/ https://www.idaho.gov/government/holidays.html https://legislature.idaho.gov/statutesrules/idstat/title67/t67ch23/sect67-2302/

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 4 of 14

A factory authorized repair and warranty service facility must be located within a one hundred (100) mile radius of delivery location listed above to provide full Custom Built Headache Rack service, repairs, factory support and full warranty repair.

Warranty must include all tools, parts, equipment, labor, and freight to repair or replace a defective warranted item, which may also include the entire Custom Built Headache Racks. All warranty work must be complete within thirty (30) calendars days after receipt of written notice from IDFG. If approved by IDFG, the Contractor may perform warranty work on-site, at the Delivery location, in lieu of pick-up and return shipping. The Contractor will be responsible for all travel costs and work-site clean-up associated with any necessary repairs. The timeframe for corrective action will still be as identified above. If the Contractor is unable to repair the Custom Built Headache Racks on-site within thirty (30) calendars days, or if the Custom Built Headache Racks continuously malfunctions and causes it to be out of service on multiple occasions, IDFG reserves the right to require the Contractor to pick-up, repair, and return the Custom Built Headache Racks at no additional cost to IDFG.

Contractor is responsible for all warranty requirements. No third-party warranties will be allowed.

E. Vendor Requirement Vendor must have a current and signed written agreement with the manufacturer stating that the vendor is an authorized dealer or authorized re-seller for the product(s) being quoted in this solicitation.

F. Remedial Action In addition to any remedies available to the State under law or equity, the State may it its sole discretion require one (1) or more of the following remedial actions if any of the service does not conform to the Contract requirements: 1) require the Contractor to take corrective action to ensure that performance conforms to the Contract requirements, 2) require the Contractor to subcontract all or part of the Contract at no additional cost to IDFG, 3) withhold payment or require payment of actual damages caused by the Discrepancy, 4) terminate the Contract pursuant to Section 2.F, Termination of Contract, in addition to any remedies imposed by the State.

If IDFG must perform or hire a separate contractor to perform any of the Contract’s requirements, which is the responsibility of the Contractor under the terms of the Contract, IDFG may withhold the actual cost to IDFG from the Contractor’s payment(s).

G. Termination of Contract For Cause - See Section 1.4, Termination, of the State of Idaho Standard Contract Terms and Conditions – July 2024.

For Fiscal Necessity – See Section 1.18, Termination for Fiscal Necessity, of the State of Idaho Standard Contract Terms and Conditions – July 2024.

For Convenience – Either party may terminate this Contract for its convenience at any time upon providing its written notification at least ninety (90) calendar days prior to the desired termination date.

ATTACHMENT 1 – SECTION 3

A. Requirements The Custom Built Headache Racks must meet the minimum specifications provided below and must be the latest model produced and sold to commercial trade. The Custom Built Headache Racks must be new, not used. Though they are not specifically covered herein, all parts necessary to provide a complete and functional Custom Built Headache Racks must be included. All parts must conform in design, strength, quality of materials, and workmanship to meet or exceed current engineering practices and accepted standards of the industry. All parts must be the manufacturers standard unless otherwise specified in this RFQ.

B. Brand Name The brand name(s) specified in this solicitation are intended to be descriptive, but not restrictive; indicative of the quality and characteristics of items that meet the minimum requirements. Contractor offering an “equal” must include documentation, which demonstrates, to IDFG’s satisfaction, that the offered item(s) meets the requirement of the solicitation. In the event documentation is not satisfactory, IDFG reserves the right to seek clarification from the Contractor. Failure to provide satisfactory documentation or a clarifying response to IDFG may eliminate the Contractor from further consideration.

C. Manuals The Contractor must provide one (1) parts manual (Manual) and one (1) operation Manual for the Custom Built Headache Racks at the time of Delivery. The manuals must include all components and exploded view drawings with both parts’ identification and parts list. The manuals must be in either paper (book) format or portable document format (PDF) via universal serial bus (USB) drive.

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 5 of 14

D. Custom Built Headache Racks – General Specifications The following Specifications are the minimum that IDFG is willing to accept.

The Racks are to be fitted to and installed on the following vehicles:

Thirteen (13) Chevy Silverado 1500 trucks.

Five (5) Chevy Silverado 2500 trucks.

The Headache racks must meet the following minimum specifications:

1. Racks must be built strong enough to support three thousand (3000) pounds of dead weight being loaded into the truck bed by the attached winch.

2. Racks must be custom built to fit on top of the front and side bed rails of the above listed trucks and is to extend five (5) inches above cab height.

3. Racks are to be to be powder coated with a durable finish, black in color

4. Frame of the rack is to be constructed out of square steel tubing for strength. The square tubing needs to be welded in a way to allow for passage of internal wiring from mounted lighting down to electrical box mounted in the bed of the truck.

5. The upper horizontal tube of the Rack must be constructed of square steel tubing, four (4) inches wide by two (2) inched deep. See Exhibit 1-A.

6. The upper horizontal tube must have a thirty-six (36) inch in length by twelve (12) inch steel diamond plate bracket extending over the truck cab to mount the enforcement light bar. See exhibit 1-B

7. Vertical Rack frame, lower Horizontal frame, Horizontal and diagonal bracing is to be constructed of two (2) inch steel square tube. See Exhibit 1.C.

8. Expanded steel, .312 inches in thickness is to be welded on driver and passenger sides of the Rack to protect vehicle occupants. See Exhibit 1.D.

9. Five eighths (5/8) inch by six (6) inch eyebolt is to be mounted in the center of the upper horizontal beam with a three (3) inch snatch block with a hook for a three eighths (3/8) inch rope to be provided by vendor. Snatch block must have at minimum a two (2) ton capacity. See Exhibit 1-E.

10. Two (2) horizontal bars will need to be welded into the center of the rack to protect the rear truck cab glass from snatch block while providing rear view mirror visibility. See Exhibit 1-F

11. Passenger and driver side horizontal bed rail supports constructed out of two (2) inch steel square tubing with diamond plate inserts as seen in exhibit 1.G

12. Rack is to have horizontal bed rail supports along the passenger and driver side. Bed rail supports must be constructed out of three (3) inch by two (2) inch angle iron, quarter (1/4) inch thick. Length of these supports is to be seventy-one (71) inches. Three (3), three (3) inch Steel U-bolt type tie downs, one half (1/2) inch thick, are to be welded on the top of each bed rail support. First tie down is to be four and a half (4 1/2) inches on center from rear of the rail support. Second tie down is to be twenty-nine (29) inches on center from the rear of the support. Third tie down is to be forty-four and a half (44 ½) inches on center from the rear of the rail support.

13. Rack is to have a quarter (1/4) inch steel plate with mounting bracket welded onto front passenger side bed rail support to mount Warn model VRX 45-S winch supplied by IDFG. See Exhibit 1-H

14. Rack is to have an eight (8) inch wide by twelve (12) inch tall by four (4) inch deep steel box constructed to house wiring components in front of the winch mounting bracket on passenger side of bed rail support. Box must sit two-and-a-half (2.5) inches above the bottom horizontal bed rail support. See Exhibit 1-H

15. Steel box must have one-and-a-half (1.5) inch round hole on the upper side wall against the cab for wiring components to run through. See Exhibit 1-I.

16. The IDFG enforcement light package supplied by IDFG for the Rack is to be mounted to the Rack and wires run internally by the vendor to the wiring housing box. Connections do not need to be made to the power source.

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 6 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 7 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 8 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 9 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 10 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 11 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 12 of 14

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 13 of 14

Exhibit 1-H

RFQ # 1457 CUSTOM BUILT HEADACHE RACKS Page 14 of 14

Exhibit 1-I

C. Submission Requirements