MC-PD-25-006_REV2_19Nov2026.pdf

PDF 286 KB Posted

Attached to
RFI - Mesh Knit Cloth Manufacturability
Solicitation number
Not on record
Issued by

About this file

This is a Purchase Description (specification document) issued by the United States Marine Corps for Cloth, Mesh Knit with 3.5 Millimeter Aperture, designated as MC-PD-25-006, Draft Revision 2, dated 19 November 2026.

The specification defines requirements for a no-melt/no-drip synthetic warp-knit mesh fabric intended for use in mesh cold weather base layer (MCWBL) undershirts and drawers as the innermost layer in multi-layer cold weather clothing systems. The cloth must be Type 1 (Modacrylic/rayon) in Class 1 (Coyote 498 color). The fabric shall be constructed as a Raschel warp-knit, Atlas (traverse) construction with knotless open net featuring diamond-shaped apertures of 3.5 millimeters (±0.5) with mesh count of 4 to 6 apertures per linear inch. Physical requirements include strand width and thickness of 1.0 millimeters (±0.2), weight of 3.75 to 4.25 ounces per square yard, and fabric thickness of 1.0 millimeters (±0.2). Performance standards mandate no melt/no drip characteristics, minimum bursting strength of 40 pounds, fabric stretch of 35 percent (wales) and 60 percent (courses), pilling rating of 4 (minimum), moisture regain not exceeding 5 percent, and drying time at 95 percent of 90 minutes maximum. Dimensional stability after three laundering cycles shall not exceed 5 percent (wales) and 12 percent (courses). The cloth must meet colorfastness requirements for laundering, crocking (wet and dry), and light exposure, and demonstrate compatibility with prolonged direct skin contact without health hazards.

Verification requirements include first article inspection and conformance inspection with material sampling based on lot size (2 samples for 800 yards or less, 3 samples for 801 through 22,000 yards, 4 samples for 22,001 yards and over). Testing shall conform to referenced standards including ASTM, AATCC, and MIL-STD-3064. Acquisition documents must specify length, width, Acceptance Quality Limits (AQLs), packaging requirements, and shade standard information per 6.2 guidance.

View the file

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

AMSC N/A FSC 8305

DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.

MC-PD-25-006

Draft Rev 2

19 NOV 2026

PURCHASE DESCRIPTION

CLOTH, MESH KNIT, 3.5 MILLIMETER APERTURE

This document is approved for use by the United States Marine Corps and is available for use by all Departments and Agencies of the Department of Defense.

1. SCOPE

1.1 Scope. This document covers the requirements for a no-melt/no-drip synthetic warp-knit mesh fabric (see 6.1).

This document specifies the finished cloth only: the form, dimensions, and physical properties the delivered cloth shall meet. Conformance testing is limited to the characteristics in Table III.

1.2 Classification. The cloth is available in one type and one class, as specified (see 6.2).

1.2.1 Types.

Type 1 – Modacrylic/rayon

1.2.2 Classes.

Class 1 – Coyote 498

2. APPLICABLE PUBLICATIONS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed.

2.2 Government publications.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-3064 – Evaluation of Quality of Textile Materials

(Copies of this document are available online at https://quicksearch.dla.mil.)

2.2.2 Other Government publications. The following other Government publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those specified in the solicitation or contract.

CODE OF FEDERAL REGULATIONS (CFR)

16 CFR 303 – Rules and Regulations Under the Textile Fiber Products Identification Act

40 CFR – Protection of Environment

(Copies of these documents are available online at www.ecfr.gov.)

2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

MC-PD-25-006

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC)

AATCC EP9 – Visual Assessment of Color Difference of Textiles

AATCC TM8 – Colorfastness to Crocking: Crockmeter Method

AATCC TM16.3 – Colorfastness to Light: Xenon-Arc

AATCC TM20 – Fiber Analysis: Qualitative

AATCC TM61 – Colorfastness to Laundering: Accelerated

AATCC TM70 – Water Repellency: Tumble Jar Dynamic Absorption

AATCC TM81 – pH of the Water-Extract from Wet Processed Textiles

AATCC TM135 – Dimensional Changes of Fabrics after Home Laundering

(Copies of these documents are available online at https://www.aatcc.org.)

AMERICAN NATIONAL STANDARDS INSTITUTE / AMERICAN SOCIETY FOR QUALITY (ANSI/ASQ)

ASQ/ANSI Z1.4 – Sampling Procedures and Tables for Inspection by Attributes

(Copies of this document are available online at https://www.asq.org.)

ASTM INTERNATIONAL

ASTM D1776 – Standard Practice for Conditioning and Testing Textiles

ASTM D1777 – Standard Test Method for Thickness of Textile Materials

ASTM D1909 – Standard Tables of Commercial Moisture Regains and Commercial Allowances for Textile Fibers

ASTM D2594/D2594M – Standard Test Method for Stretch Properties of Knitted Fabrics Having Low Power

ASTM D3512/D3512M – Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Random Tumble Pilling Tester

ASTM D3776/D3776M – Standard Test Methods for Mass Per Unit Area (Weight) of Fabric

ASTM D3787 – Standard Test Method for Bursting Strength of Textiles – Constant-Rate-of-Traverse (CRT) Ball Burst Test

ASTM D3939/D3939M – Standard Test Method for Snagging Resistance of Fabrics (Mace)

ASTM D6413/D6413M – Standard Test Method for Flame Resistance of Textiles (Vertical Flame Test)

ASTM D6797 – Standard Test Method for Bursting Strength of Fabrics – Constant-Rate-of-Extension (CRE) Ball Burst Test

(Copies of these documents are available online at https://www.astm.org.)

ORGANISATION FOR ECONOMIC COOPERATION AND DEVELOPMENT (OECD)

OECD Guidelines for the Testing of Chemicals, Section 4, Test No. 404 – Acute Dermal Irritation/Corrosion

OECD Guidelines for the Testing of Chemicals, Section 4, Test No. 406 – Skin Sensitisation

(Copies of these documents are available online at https://www.oecd-ilibrary.org.)

SAE INTERNATIONAL

AMS-STD-595 – Colors Used in Government Procurement

AMS-STD-595/20150 – Coyote 498

(Copies of these documents are available online at https://www.sae.org.)

2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.2.

3.2 Conformance inspection. When specified (see 6.2), a sample shall be subjected to conformance inspection in accordance with 4.3. Conformance inspection is limited to the characteristics marked for conformance in Table III.

3.3 Recycled, recovered, biobased, or environmentally sustainable materials. Recycled, recovered, biobased, and environmentally sustainable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

3.4 Description. The cloth is an open mesh, warp-knit fabric engineered for rapid moisture transport from the skin to the next clothing layer, air permeability, and insulation via micro air pockets held open by the strand (cord) form specified in 3.5 (see 6.1). The cloth shall transfer moisture to the next layer and shall not retain moisture against the skin.

3.5 Form

3.5.1 Pattern and form. The finished cloth shall be a Raschel warp-knit, Atlas (traverse) construction, knotless open net. The cloth shall present diamond-shaped apertures in an open net form, each aperture bounded by strands that are interlooped at the nodes, not knotted. A knotted net, a weft-knit mesh, a tricot mesh, and a flat jersey mesh do not comply. The finished cloth, in the relaxed state, shall meet the mesh count, aperture size, and strand requirements of Table I.

3.5.2 Cord form and roundness. Each strand (cord) shall consist of multiple ends fed together and plied or cabled into a rounded cord form. Strand width (relaxed) shall be 1.0 mm (± 0.2) and strand thickness (relaxed) shall be 1.0 mm (± 0.2), per Table I. Strand thickness shall be not less than 0.8 times strand width when measured on the same strand (see 4.5.1.1.4). A strand that meets width but not thickness is a flat strand and is not acceptable. Strand thickness under a 0.5 kPa load shall be not less than 0.7 mm (first article only, see Table III). The finished cloth shall meet the strand thickness and thickness-to-width ratio requirements of Table I after laundering (see Table I, dimensional stability).

3.6 Physical requirements. The cloth shall conform to the requirements specified in Table I when tested as specified in 4.5.1.

TABLE I. Physical requirements

Characteristic Requirement

Construction Raschel warp-knit, Atlas (traverse) knotless open net (see 3.5)

Pattern Diamond-shaped open mesh

Mesh count (relaxed), apertures per linear inch 4 to 6 (inclusive)

Aperture size (relaxed), millimeters (mm) 3.5 (± 0.5)

Strand width (relaxed), mm 1.0 (± 0.2)

Strand thickness (relaxed), mm 1.0 (± 0.2)

Strand thickness-to-width ratio (minimum) 0.8

Characteristic Requirement

Strand thickness under 0.5 kPa load, mm (minimum) * 0.7

Fiber content of yarns Modacrylic / rayon

Weight, ounces per square yard 1/ 3.75 – 4.25

Thickness, fabric (relaxed), mm 1.0 (± 0.2)

Snag rating (minimum): wales / courses 4 / 4

Pilling, rating (minimum) 4

Moisture regain, percent (maximum) 5

Drying time at 95 percent, minutes (maximum) 90

Dimensional stability after 3 laundering cycles, percent (maximum): wales 5

Dimensional stability after 3 laundering cycles, percent (maximum): courses 12

Bursting strength, pounds (minimum) 40

Fabric stretch, percent (minimum): wales / courses 35 / 60

Fabric growth, percent (maximum): wales / courses 2/ 5 / 10

Vertical flame (initial and after 5 launderings): wales and courses No melt / no drip pH (water extract) 5.0 – 8.5

Labile sulfur See 3.7

Colorfastness to laundering (3 cycles), rating (minimum) 4

Colorfastness to crocking, wet / dry, rating (minimum) 4 / 4

Colorfastness to light after 40 AFU 3/ (or 170 kJ/m²nm 4/ at 420 nm), rating (minimum)

Visual shade matching, daylight D65 (6500 ± 200 K) Coyote 498 5/ 6/

Visual shade matching, incandescent A (2856 ± 200 K) Coyote 498 5/ 6/

* First article only (see Table III).

1/ Provisional. The weight range is a Government estimate. It shall be confirmed on the approved first article. If cloth that meets the cord geometry of 3.5 cannot meet this weight range, the weight range shall be revised by amendment; the cord geometry shall not be waived to meet the weight.

2/ After two hours of tension, followed by one hour of no tension.

3/ AATCC fading units.

4/ Kilojoules (kJ) per square meter nanometer (m²nm).

5/ Or as specified in the contract or order (see 6.2).

6/ See 6.3.2.

3.7 Labile sulfur. The use of dyes and compounds containing sulfur capable of oxidation to sulfuric acid shall be chosen and applied such that the dyed and finished cloth shall show a rating of “slight” or “free” labile sulfur when tested as specified in 4.5.1.4.

3.8 Toxicity. When tested as specified in 4.5.3, the finished cloth shall not present a health hazard and shall show compatibility with prolonged, direct skin contact, as specified in 40 CFR §798.2250, Dermal Toxicity, and 40 CFR §798.4100, Dermal Sensitization. Chemicals recognized by the Environmental Protection Agency as human carcinogens shall not be used.

3.9 Length, width, and put-up.

3.9.1 Length and put-up. Unless otherwise specified (see 6.2), for Government procurements only, the cloth shall be furnished in continuous lengths, each not less than 40 yards, and each length shall be put up on a roll when examined in accordance with 4.5.2.

3.9.2 Width. For Government procurements only, the width of the finished cloth shall be as specified in the procurement document (see 6.2) and shall be the minimum acceptable width, inclusive of the selvage, when examined in accordance with 4.5.2.

3.10 Roll identification.

3.10.1 Fiber identification. Each roll shall be labeled or ticketed for fiber content in accordance with 16 CFR 303 when examined in accordance with 4.5.2.

3.10.2 Face identification. The face side of the cloth shall be identified by stamping the face side with the word “FACE” at each end of the roll when examined in accordance with 4.5.2.

3.11 Workmanship. The cloth shall conform to the quality of product established by this document. The cloth shall be uniform, and the occurrence of defects, when examined in accordance with 4.5.2, shall not exceed the established Acceptance Quality Limits (AQL) (see 6.2) and shall not adversely affect the serviceability, appearance, and uniformity of the product.

4. VERIFICATION

4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:

a. First article inspection (see 4.2).

b. Conformance inspection (see 4.3).

4.2 First article inspection. The first article (see 3.1) shall be examined in accordance with 4.5.1 through 4.5.3 for compliance with form, appearance, color, finish, testing, and workmanship requirements as specified in this document. A first article with a flat strand is not acceptable, whether or not the other measured values are within tolerance (see 3.5.2).

4.2.1 First article samples and acceptance criteria. Unless otherwise specified in the contract or order (see 6.2), first article samples shall be provided. The sample unit shall be one continuous 5-yard length of full-width cloth.

The presence of defects exceeding the established AQLs specified in the procurement document (see 6.2) or failure of any test specified in 4.5.1 through 4.5.3 shall be cause for rejection of the first article.

4.3 Conformance inspection. Unless otherwise specified in the contract (see 6.2), conformance inspection in accordance with 3.2 shall consist of the examinations and tests marked for conformance in Table III and the visual examination in 4.5.2. No other laboratory test is required for a conformance lot.

4.3.1 Conformance sampling and acceptance criteria. Unless otherwise specified in referenced documents or procurement documents (see 6.2), material sampling shall be in accordance with Table II. For material testing, the sample unit shall be 5 continuous yards full-width of the finished cloth. For visual inspection, the sample unit shall be a roll of fabric. The lot shall be unacceptable if one or more sample units fail to meet any conformance test requirement in Table III or fail to meet the AQLs (see 3.11) as defined by the contract (see 6.2).

TABLE II. Material sampling

Lot size (yards) Sample size (sample units)

800 or less 2

801 through 22,000 3

22,001 and over 4

4.4 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to test such items to determine the validity of the certification (see 6.2).

4.4.1 Toxicity certification. Unless otherwise specified, a certificate of compliance, supported by historical use data where available (see 4.5.3), will be acceptable as evidence that the finished cloth conforms to 3.8.

4.5 Inspection methods. Unless otherwise specified in the contract or order, inspection methods shall be as specified in the associated test method or procedure (see 6.2).

4.5.1 Material examinations and tests. The cloth shall be tested in accordance with the examinations and tests referenced in Table III unless otherwise excluded, amended, or modified in applicable procurement documents (see 6.2). Characteristics marked “First article” are verified on first article samples only and are not required for each conformance lot.

TABLE III. Basic material verification

Characteristic Requirement Verification method Inspection

Form, pattern, and cord form 3.5 & 3.6 Visual examination First article and conformance Mesh count 3.6 4.5.1.1.1 First article and conformance

Aperture size 3.6 4.5.1.1.2 First article and conformance

Strand width 3.6 4.5.1.1.3 First article and conformance Strand thickness and thickness-to-width ratio

3.5.2 & 3.6 4.5.1.1.4 First article and conformance

Strand thickness under 0.5 kPa load 3.5.2 & 3.6 4.5.1.1.4 First article only

Fiber content 3.6 AATCC TM20 First article only

Weight 3.6 ASTM D3776 / D3776M (Method C) First article and conformance Thickness, fabric 3.6 ASTM D1777 First article and conformance Snag, wales and courses 3.6 ASTM D3939 / D3939M First article only

Pilling 3.6 ASTM D3512 / D3512M First article only

Moisture regain 3.6 ASTM D1909 and 4.5.1.2 First article only

Drying time 3.6 4.5.1.3 First article only

Dimensional stability, wales and courses 3.6 AATCC TM135 (1, III, Ai) First article only

Bursting strength 3.6 ASTM D3787 or ASTM D6797 1/ First article and conformance Fabric stretch, wales and courses 3.6 ASTM D2594 / D2594M 2/ First article only

Fabric growth, wales and courses 3.6 ASTM D2594 / D2594M 2/ First article only

Vertical flame, wales and courses 3.6 ASTM D6413 / D6413M First article and conformance pH 3.6 AATCC TM81 First article only

Labile sulfur 3.7 4.5.1.4 First article only

Colorfastness to laundering 3.6 AATCC TM61 (Test 2A) First article only

Colorfastness to crocking (wet and dry) 3.6 AATCC TM8 First article only

Colorfastness to light 3.6 AATCC TM16.3 (Option 3) First article only

Visual shade matching, daylight D65 and incandescent A

3.6 AATCC EP9 (Option C) (see 4.5.4 and 6.3) First article and conformance

1/ The test method used is at the discretion of the vendor and shall be specified in all reporting of the results.

2/ Use conditioning and procedures specified in ASTM D2594 / D2594M for form-fitting items.

4.5.1.1 Mesh measurements. The cloth shall be laid flat, allowed to rest for a minimum of 90 seconds, and under no tension when the measurements are taken. Specimens shall be conditioned in accordance with ASTM D1776 unless the method specifies otherwise.

4.5.1.1.1 Mesh count. The mesh count shall be determined by counting the number of apertures per linear inch in both the wale and course directions. A minimum of five different areas of cloth shall be counted in each direction, and each area shall be at least four inches from any other measured area. See Figure 1.

FIGURE 1. Mesh count

4.5.1.1.2 Aperture size measurement. Aperture size shall be measured across the diagonal of a diamond aperture, from node to node, in both the wale and course directions. A minimum of five apertures shall be measured in each direction and each aperture shall be at least four inches from any other measured aperture. The average of all the measurements shall be the recorded aperture size. See Figure 2.

FIGURE 2. Aperture size measurement

4.5.1.1.3 Strand width measurement. The strand width shall be measured perpendicularly across the middle of a strand (equidistant from two nodes). A minimum of ten different strands shall be measured, and each strand shall be at least four inches from any other measured strand. The average of all the measurements shall be the recorded strand width. See Figure 3.

FIGURE 3. Strand width measurement

4.5.1.1.4 Strand thickness and ratio. Strand thickness shall be measured on the same strands measured in 4.5.1.1.3, at the middle of the strand, using a micrometer or thickness gauge that does not compress the cord. The average strand thickness and the ratio of average strand thickness to average strand width shall be recorded. At first article, strand thickness shall also be measured under a 0.5 kPa load in accordance with ASTM D1777 and recorded.

4.5.1.2 Moisture regain. The commercial moisture regain (CMR) values from ASTM D1909 shall be used for the fibers in the yarn blend to calculate the moisture regain as the sum, over each fiber, of (CMR of the fiber × blend percentage of the fiber). Example: 78/22 modacrylic/rayon fabric: (0.4% × 78%) + (11% × 22%) = 2.7% commercial moisture regain, where 0.4% is the CMR value for modacrylic fiber and 11% is the CMR value for rayon fiber.

4.5.1.3 Drying time. Drying time shall be determined by the wringer method of AATCC TM70. Three specimens, 2 inches × 2 inches, shall be conditioned, weighed, submerged in distilled water for 30 minutes, sandwiched between unused AATCC textile blotting paper, and passed through a motor-driven wringer set at 27.7 kg in accordance with AATCC TM70. Each specimen shall then be weighed at intervals until it has lost 95 percent of the absorbed water. The average drying time of the three specimens shall be the recorded drying time. The test shall be run at 65 (± 2) percent relative humidity and 70 (± 2) °F.

4.5.1.4 Presence of labile sulfur test. In the determination of the presence of labile sulfur in textile materials with lead acetate, two 1.50 (± 0.01) gram samples from each material submitted for evaluation shall be tested. Each sample shall be cut into very small pieces and placed into a separate test tube. The samples shall be submersed in a stannous chloride solution containing 100 grams of American Chemical Society (ACS) grade stannous chloride crystals in 100 milliliters of ACS grade hydrochloric acid (35 percent concentration) and 50 milliliters of distilled water. A filter paper wet out with a 5.0 percent lead acetate solution shall be placed over the top of the test tube. The lead acetate solution contains 5.0 grams of chemically pure (CP) reagent grade lead acetate and enough distilled water to make up a 100-milliliter solution; if the solution is not clear, a few drops (one at a time) of glacial acetic acid shall be added until the solution is clear. The test tube containing the textile sample, stannous chloride, and wet filter paper shall be heated over a low flame until the solution is boiling. The solution should not be heated for more than 15 seconds. A brown or black stain on the filter paper shall be evaluated as follows:

a. Free – The filter paper shows no discoloration or staining of any kind.

b. Slight – The filter paper shows a light tan to light brown discoloration stain.

c. Moderate – The filter paper shows a dark brown discoloration stain.

d. Severe – The filter paper shows a black color stain.

Results of the testing should be reported as “pass” or “fail”.

4.5.2 Visual examination. Each roll in the sample shall be examined on the face side in accordance with MIL- STD-3064, Type V yard-by-yard examination, roll examination, and shade examination for defects.

4.5.3 Toxicity test. When the toxicity requirement (see 3.8) can be demonstrated with historical use data, toxicity testing may not be required on the finishing treatments used. If dermal toxicity testing is required (see 6.2), it shall be conducted in accordance with 40 CFR §798.2250 and 40 CFR §798.4100, which are consistent with OECD Guidelines for the Testing of Chemicals, Section 4, Test Nos. 404 and 406 (see 6.4).

4.5.4 Visual shade matching. The color and appearance of the fabric shall match the standard sample when viewed using AATCC EP9, Option C (see 6.3) with a primary light source simulating the spectral quality of average daylight, CIE Illuminant D65, with a color temperature of 6500 (± 200) Kelvin (K) and illumination of 100 (± 20) foot-candles. Alternatively, the color and appearance of the fabric shall match the standard sample with a primary light source simulating artificial daylight, CIE Illuminant D75, with a color temperature of 7500 (± 200) K and illumination of 100 (± 20) foot-candles in lieu of D65 (see 6.3.1). The fabric shall also be a good match to the standard sample with a secondary source simulating the spectral quality of incandescent lamplight, CIE Illuminant A, with a color temperature of 2856 (± 200) K.

5. PACKAGING

5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands.

6. NOTES

(This section contains information of a general or explanatory nature that may be helpful but is not mandatory.)

6.1 Intended use. The cloth is used in the mesh cold weather base layer (MCWBL) undershirt and drawers, which are designed to be worn as the innermost layer in a multi-layer cold weather clothing system to manage moisture and promote thermoregulation. Moisture transfer to the next layer is the primary function.

6.2 Acquisition requirements. Acquisition documents should specify the following:

a. Title, number, and date of this purchase description.

b. The specific issue of individual documents referenced (see 2.2 and 2.3).

c. When first article is required (see 3.1 and 4.2).

d. When conformance inspection is required (see 3.2 and 4.3).

e. Length and put-up required (see 3.9.1).

f. Width required (see 3.9.2).

g. AQLs (see 3.11 and 4.3.1).

h. First article sampling and acceptance criteria (see 4.2.1).

i. Conformance sampling and acceptance criteria (see 4.3.1).

j. Material examinations and test exclusions (see 4.5.1).

k. Toxicity testing requirements (see 4.5.3).

l. Packaging requirements (see 5.1).

m. Shade standard information (see 6.3.2).

6.3 Visual shade matching. In 2017, Option A of AATCC EP9 was changed to Option C. NOTE: In case of confusion, the viewing geometry should be: “The specimen plane and illumination source will be parallel to each other and aligned so that the light flux is incident at the center of the specimen plane, which is set at a 35 (± 5°) angle relative to the horizontal. The observer will view the specimens at a 90° angle, relative to the plane of the specimens.”

6.3.1 Use of CIE Illuminant D75. In 2022, all services of the United States military accepted CIE Illuminant D65 as the new preferred light source for visual shade matching due to supply chain issues with CIE Illuminant D75.

6.3.2 Shade criticality. Some items may be deemed “non-shade-critical” by the contracting agency and alternative shade standards or information regarding shade may be specified in the contract or order (see 6.2). It is recommended that manufacturers refer to the contract or order to determine the criticality of the shade matching or alternate shade standards that are acceptable.

6.4 Toxicity testing. OECD Guidelines for the Testing of Chemicals, Section 4, Test Nos. 404 and 406 are recommended by the Office of the Surgeon General to assess the requirement of 3.8, but other test methods may be used. It is recommended that alternative test methods be assessed by the contracting agency prior to being used to address the toxicity requirements.

6.6 Subject term (keyword) listing.

Baselayer Cold weather Mesh knit

ICEPS

USMC

File details come from the government source that posted it. Updated .