Plans_-_CC_Administration_Building_BAS_Upgrade_6.30.26.pdf

Te xa s Re g is te re d F irm N o

F

-7

W e st

TH

S t.

Su it e

Pl a no

TX

9.

7.

Em a il:

m d e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in gCOLLIN COUNTY ADMINISTRATION

BUILDING AUTOMATION

SYSTEM UPGRADE FOR JACK

HATCHELL ADMINISTRATION

BUILDING

McKinney, TX 75071

June 30, 2026

COVER

SHEET

INDEX OF DRAWINGS

6/30/2026

ASHRAE CO

700 PPM ---- 15 CFM/PERSON

500 PPM ---- 20 CFM/PERSON

350 PPM ---- 30 CFM/PERSON

C

C 1

2C

2 DIFFERENTIAL

1. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL

SYSTEM AS INDICATED ON THE DRAWINGS, AS SPECIFIED AND AS

REQUIRED BY ALL NATIONAL, STATE AND LOCAL CODES.

2. CONTRACT DRAWINGS FOR MECHANICAL WORK (HVAC, PLUMBING, AND

FIRE PROTECTION) ARE DIAGRAMMATIC AND ARE INTENDED TO CONVEY

SCOPE AND GENERAL ARRANGEMENT ONLY. IT IS THE CONTRACTORS

RESPONSIBILITY FOR INSTALLING ALL MATERIALS PER SMACNA

STANDARDS AND THE MANUFACTURER'S STANDARDS.

3. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER OR BY A 3RD PARTY. IT IS THE CONTRACTORS

RESPONSIBILITY TO VERIFY ALL MEP SERVICES ARE LOCATED AS

DESIGNED BEFORE BIDDING THE PROJECT. IN OCCURRENCES WHERE

EXISTING DOES NOT MATCH DESIGNED, IT IS THE CONTRACTORS

RESPONSIBILITY TO NOTIFY THE OWNER, ARCHITECT, & ENGINEER

BEFORE PROCEEDING. IF ANY DISCREPANCIES ARE NOT IDENTIFIED AT

BIDDING, THE COST SHALL BE ABSORBED BY THE CONTRACTOR AND

NOT PASSED ONTO THE OWNER OR ENGINEER OF RECORD.

4. COORDINATE CONSTRUCTION OF ALL MECHANICAL WORK WITH

ARCHITECTURAL, STRUCTURAL, CIVIL, ELECTRICAL WORK, ETC., SHOWN

ON THE OTHER CONTRACT DRAWINGS.

5. WHEN TWO OR MORE ITEMS OF THE SAME TYPE OF EQUIPMENT ARE

REQUIRED, THE PRODUCT OF ONE MANUFACTURE SHALL BE USED.

6. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE AND DIVISION 23 OF THE

SPECIFICATION.

7. ALL MISCELLANEOUS STEEL REQUIRED TO ENSURE PROPER

INSTALLATION AND AS SHOWN IN DETAILS FOR PIPING, DUCTWORK, AND

EQUIPMENT (UNLESS OTHERWISE NOTED) SHALL BE FURNISHED AND

INSTALLED BY THE MECHANICAL CONTRACTOR.

8. MECHANICAL EQUIPMENT, DUCTWORK, AND PIPING SHALL NOT BE

SUPPORTED FROM METAL DECK.

9. LOCATION AND SIZES OF ALL FLOOR, WALL, AND ROOF OPENINGS SHALL

BE COORDINATED WITH ALL OTHER TRADES.

10. PROVIDE REMOTE BALANCING DAMPERS SIMILAR TO 'YOUNG

CONCEALED REGULATORS' FOR ALL TAPS MADE ABOVE INACCESSIBLE

CEILINGS OR WALLS. FINISH CONCEALMENT COVERS PER ARCHITECTS

RECOMMENDATIONS.

11. ALL AHU AND FCU FANS SHALL OPERATE CONTINUOUSLY DURING THE

OCCUPIED MODE OF OPERATION WITH ASSOCIATED OUTSIDE AIR

MOTORIZED DAMPERS IN THE FULL OPEN POSITION (UNLESS NOTED

OTHERWISE OR DCV SYSTEM). DAMPER SHALL BE CLOSED WITH THE

FANS OPERATIONAL IN THE MORNING WARM UP OR COOL DOWN

MODES.

12. CONTRACTOR SHALL MAINTAIN A MINIMUM CLEARANCE OF 10'-0"

BETWEEN OUTSIDE AIR INTAKE POINTS AND ANY EXHAUST AIR,

CONTAMINATED RELIEF AIR OR PLUMBING VENT TERMINATION POINTS.

13. CONDENSATE PIPING DOWN TO A PLUMBING FIXTURE SHALL BE FULLY

INSULATED WITHIN WALL. PROVIDE ESCUTCHEON PLATE AT WALL.

PIPING SHALL NOT BE ROUTED EXPOSED TO VIEW.

14. PRESSURIZED LIQUID, GAS, AIR SYSTEM PIPE AND ELECTRICAL CONDUIT

SHALL NOT BE ROUTED BENEATH ANY SUSPENDED EQUIPMENT. FIRE

PROTECTION, ELECTRICAL AND MECHANICAL CONTRACTORS SHALL

COORDINATE TRADES.

15. ALL REMOTE MOUNTED DISCONNECT SWITCHES FOR MECHANICAL

EQUIPMENT SHALL HAVE I.D. NAME PLATES.

16. PIPING ON ROOF - CONTRACTOR SHALL PROVIDE ROOF PIPE SUPPORTS

ON 5'-0" CENTERS, EACH CHANGE IN DIRECTION, EACH ROOFTOP UNIT

AND EACH PIPE PENETRATION THROUGH ROOF. REFER TO MECHANICAL

SPECIFICATIONS FOR REQUIRED OFFSETS OR LOOPS FOR PIPE

EXPANSION.

17. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

18. ALL SAW CUTTING SHALL BE PERFORMED AFTER HOURS SO THAT

OPERATION DOES NOT DISTURB NEIGHBORING TENANTS. THERE SHALL

BE NO GAS POWERED EQUIPMENT IN TENANT AREAS.

GENERAL PROJECT NOTES:GENERAL HVAC NOTES:

FLOOR CONTROL VALVE

TEE

TEE, UP

TEE, DOWN

SINGLE SWEEP TEE

CROSS

LATERAL

45 DEGREE ELBOW

90 DEGREE ELBOW

90 DEGREE ELBOW UP

CAP

HVAC VALVE

VENT THRU ROOF

BUTTERFLY VALVE

SOLENOID VALVE

EXPANSION JOINT

FLOAT AND THERM. TRAP

BUCKET STEAM TRAP

FLOOR CLEAN OUT

FIRE HOSE CABINET

PRESSURE RELIEF VALVE

CONTROL, 2 WAY VALVE

CONTROL, 3 WAY VALVE

STRAINER & BLOW OFF VALVE

PRESSURE GAUGE & COCK

UNION OR COMPANION FLANGES

PRESSURE & TEMPERATURE TAP (PETES PLUG)

MANUAL AIR VENT

TEMPERATURE SENSOR

PRESSURE SENSOR

THERMOMETER & WELL

HOSE END DRAIN

AUTOMATIC AIR VENT

FLOW METER

T S

F FLOW SWITCH

ANCHOR (PIPE)

HOSE BIBB

B

B

T

H

F

F.H.C.

D.S.

CO

CO

OR

R.D.

V.T.R.

HUMIDISTAT

CLEAN OUT

GATE VALVE

FLOOR DRAIN

HUB DRAIN

DOWN SPOUT

ROOF DRAIN

CHECK VALVE

GLOBE VALVE

BALL VALVE

PLUG VALVE

THERMOMETER

THERMOSTAT

OS & Y VALVE

& FITTINGS SYMBOLS

ALL SYMBOLS ON THIS LIST ARE NOT NECESSARILY USED ON THIS JOB.

BALANCING VALVE (WITH PETE'S PLUG EITHER SIDE)

SINGLE W.F. LATERAL STUB

DOUBLE W.F. LATERAL STUB

DOUBLE W.F. LAT & TRAP

FLOOR DRAIN RISER W/TRAP

SINGLE W.F. LAT. & TRAP

O.D. OVERFLOW ROOF DRAIN

PIPE GUIDE

COMPRESSED AIR TAP

MOTORIZED ISOLATION VALVE (2-POSITION-24v)

MANUALLY CALIBRATED BALANCING VALVE

AUTOMATIC FLOW CONTROL VALVE

PIPE SIZE REDUCER (CONCENTRIC)

90 DEGREE ELBOW DOWN

ANGLE GATE VALVE

ANGLE GLOBE VALVE

PIPE SIZE REDUCER (ECCENTRIC)

MOTORIZED CONTROL VALVE (MODULATING-24v)

DIRECTION OF FLOW

EQUIP. OR FIXTURE DRAIN LINE

SYMBOL DESCRIPTION

RL

RS

CD

PC

D

STATIC PRESSURE SENSOR

R/A GRILLE OR REGISTER

4-WAY THROW (U.N.O.)

S/A GRILLE/REGISTER W/ SQUARE NECK.

MOTORIZED DAMPER (WITH END SW.)

THERMOSTAT OR TEMP SENSOR)/

FIRE/SMOKE DAMPER (WITH SM. DET.)

VOLUME DAMPER

FIRE DAMPER

FLEX CONNECTION. 4-WAY THROW (U.N.O.)

S/A GRILLE/REGISTER W/ ROUND NECK &

FSD

FD

90 DEGREE S/A ELBOW DOWN

90 DEGREE S/A ELBOW UP

90 DEGREE R/A ELBOW UP

90 DEGREE R/A ELBOW DOWN

SIDEWALL SUPPLY GRILLE OR

REGISTER WITH AIR EXTRACTOR

SPIN-IN TAP WITH DAMPER

VANES & SPLITTER DAMPER

SQUARE ELBOW WITH DOUBLE

TEE WITH SQUARE ELBOWS, TURNING

BRANCH TAKE-OFF

WITH VANED EXTRACTOR

RADIUS ELBOW (R=1.5 MIN.)

ACCESS DOORAD AD

SHEET METAL DUCT 16"x12"

DIRECTION OF FLOW

SUPPLY DUCT SECTION UP

WYE JUNCTION

BRANCH TAKE-OFF

FLEXIBLE DUCT CONN. WITH DAMPER

SIZE OR SHAPE TRANSITION

45 DEGREE ELBOW (R=1.5 MIN.)

RADIUS ELBOW (R=1.5 MIN.)

ROUND ELBOW UP (R/A SIMILAR)

ROUND ELBOW DOWN (R/A SIMILAR)

HIDDEN SHEET METAL DUCT

INTERNALLY INSULATED SHEET METAL

DUCT

EXHAUST DUCT SECTION DOWN

16X12

16"x12"

M

SP

FSD

FD

M

SP

T

AFAF AIRFLOW MEASURE STATION

SMOKE DAMPER (WITH SM. DET.) SDSD

DUCTWORK LEGEND

WALL TURNING VANES

H C/ /

HUMIDISTAT/CARBON DIOXIDE SENSOR

ALL SYMBOLS ON THIS LIST ARE NOT NECESSARILY USED ON THIS PROJECT.

16"x12"

DUCT MOUNTED SMOKE DETECTOR

(TUBE SENSING TYPE)

P P

COUNTER WEIGHTED BACKDRAFT DAMPERBD BD

ABOVE

ALTERNATING CURRENT

AIR CONDITIONER

ABOVE FINISHED FLOOR

ABOVE GRADE AND GFI

AIR HANDLING UNIT

ALTERNATE

AMPERE

APPROXIMATELY

ARCHITECTURAL

AVERAGE

BOILER

BAROMETRIC RELIEF DAMPER

BRITISH THERMAL UNIT

CUBIC FEET PER MINUTE

CONSTRUCTION DOCUMENTS

CHILLER

CHEMICAL

CHILLED WATER PUMP

CEILING

COMPRESSOR

COOLING TOWER

CONDENSER WATER PUMP

DRY BULB

DETAIL

DIAMETER

DIMENSION

DESIGN DEVELOPMENT

ENTERING DRY BULB

ELECTRICAL

ELEVATION

ENTERING WET BULB

ENTERING WATER TEMPERATURE

EXHAUST

EXISTING

DEGREES FAHRENHEIT

GROUND FAULT INTERRUPTER

GALLONS PER MINUTE

FEET PER MINUTE

FEET PER SECOND

FOOT OR FEET

HEAD

HEAT PUMP UNIT

HOUR(S)

HEIGHT

HEATER

HEAT,VENT AND AIR CONDITIONING

HOT WATER PUMP

HEAT EXCHANGER

FREQUENCY (HERTZ)

INSIDE DIAMETER OR DIMENSION

INCHES

KILOWATT

KILOWATT HOUR

MAXIMUM

LEAVING WATER TEMPERATURE

1000 BTU PER HOUR

MECHANICAL

MANUFACTURER

MINIMUM

NUMBER

NOT APPLICABLE

NOISE CRITERIA

NECK DIMENSION

OPPOSED BLADE DAMPER

OUTSIDE DIAMETER

OUTSIDE AIR

ORIGINAL

PHASE

POWERED MIXING BOX

PLUMBING

PRESSURE

PANEL

REFERENCE

RETURN AIR

RETURN AIR GRILLE

ROOF TOP UNIT

STAND ALONE DIGITAL CONTROLLER

SENSIBLE

SQUARE

SUPPLY AIR

STATIC PRESSURE

SINGLE SPEED MOTOR

START/STOP/STATUS

TEMPERATURE

VOLT

VARIABLE AIR VALVE

VELOCITY

WATT

WITH

WEATHERPROOF

WATER PRESSURE DROP

WEATHERPROOF GFI

TRANSFORMER

ABV.

AC

A/C

AFF

AG

AHU

ALT.

AMP.

APPROX.

ARCH.

AVG.

B

BRD

BTU

CFM

CD

CH.

CHEM.

CHP

CLG.

CMPR.

CT

CWP

DB

DET.

DIA.

DIM.

DD

EDB

ELEC.

ELEV.

EWB

EWT

EXH.

EXIST.

DEG. F

GFI

GPM

FPM

FPS

FT.

HD.

HPU

HR.

HT.

HTR.

HVAC

HWP

HX

HZ.

ID

IN.

KW

KWH

MAX.

LWT

MBH

MECH.

MFR.

MIN.

NO.

N/A

NC

NK

OBD

OD

OA

ORIG.

PH.

PMB

PLBG.

PRESS.

PNL.

RE.

RA

RAG

RTU

SDC

SENS.

SQ.

SA

SP

S/S S/S/S

TEMP.

V

VAV

VEL.

W W/

WP.

WPD

WPG

XFMR.

AFG ABOVE FINISHED GRADE

CKT. CIRCUIT

DEFL. DEFLECTION

MVD MANUAL VOLUME DAMPER

WB WET BULB

MEP ABBREVIATIONS

WITHOUTW/O

UNO UNLESS NOTED OTHERWISE

UH UNIT HEATER

SAG SUPPLY AIR GRILLE

LAT LEAVING AIR TEMPERATURE

HP HORSE POWER

FLR. FLOOR

FAN COIL UNITFCU

EF EXHAUST FAN

CONDENSING UNITCU

RD. RADIUS

HOA HANDS/OFF/AUTO. MOTOR STARTER

HTG. HEATING

EA EXHAUST AIR

F/A FREE AREA OPENING (SQ. FT.)

ABOVE FINISHED CEILINGAFC

NOT IN CONSTRUCTIONNIC

W.G. WATER GAUGE

TOTAL STATIC PRESSURE (IN. W.G.)T.S.P.

MOTOR STARTERSTR.

SEER SEASON ENERGY EFFICIENCY RATIO

AMB. AMBIENT TEMPERATURE (F. DEGREE)

BUILDING MANAGEMENT SYSTEM BMS

CUBIC FEET PER HOURCFH

DISC. DISCONNECT SWITCH

ENERGY MGMT. CONTROL SYSTEM

EXTERNAL STATIC PRESS. (IN. W.G.)E.S.P.

EMCS.

P.D. PRESSURE DROP (FT)

RPM REVOLUTIONS PER MINUTE

FRACTIONAL HORSE POWERFHP

COIL FINS PER INCH.FPI

MCA

MOCP

MINIMUM CURRENT AMPS.

MAX. OVER CURRENT PROTECTION

BELOW GRADEB.G.

AHAP AS HIGH AS POSSIBLE

OWNERS AUTHORIZED REPRESENTATIVEOAR

OWNER FURNISHED CONTRACTOR INSTALLEDOFCI

REFRIGERANT LIQUID LINE

REFRIGERATED SUCTION LINE

CONDENSATE DRAIN LINE (HVAC)

PUMPED CONDENSATE

REFRIGERANT SUCTION & LIQUID LINES

REFRIG. SUCTION, LIQUID, HOT GAS LINES

RS/L

RS/L/H

AIAI AIRFLOW IONIZER STATION

SECTION

DETAIL SYMBOL

(ALL SYMBOLS MAY NOT APPEAR ON DRAWINGS)

DRAWING SYMBOLS

NOTE BY SYMBOL

AIR DISTRIBUTION DEVICE

SUBTITLE

X

XX

XX

XX

XX

XX XX

NUMBER

DESCRIPTION

SCALE

DETAIL #

DRAWING NO. TO REFER TO

ARROWS INDICATE

THROW PATTERN

DRAWING NUMBER WHERE

SECTION IS LOCATED

SECTION NUMBER

GAS PRESSURE REDUCING VALVE

WATER PRESSURE REDUCING VALVE

T H C/ /

ELEVATION/ RISER DIAGRAM SYMBOL

XX

XX

DRAWING NUMBER

POINTS TO ELEVATION/ RISER AREA

ELEVATION/ RISER #

(ALL DESIGNATIONS MAY NOT APPEAR ON DRAWINGS.)

PIPING DESIGNATIONS

1. WITHOUT PRIOR APPROVAL FROM ENGINEER AND OWNER, ALL MECHANICAL

EQUIPMENT SHALL NOT BE OPERATED DURING CONSTRUCTION OF THE

BUILDING PER MANUFACTURER RECOMMENDATIONS. MECHANICAL

CONTRACTOR IS RESPONSIBLE TO PROVIDE TEMPORARY HEATING OR COOLING

AS NEEDED TO CLIMATIZE THE BUILDING.

2. ALL PIPING AND DUCTS IN FINISHED ROOMS OR SPACES SHALL BE CONCEALED

WITHIN FURRED CHASES OR ABOVE SUSPENDED CEILINGS.

3. ALL DUCTWORK SIZES ARE PROVIDED IN CLEAR INSIDE AIRSTREAM

DIMENSIONS. INCREASE DUCT SIZES TO ACCOMMODATE ANY INTERNAL

INSULATION REQUIREMENTS (AS SPECIFIED). PROVIDE A MINIMUM OF 15 LINEAR

FT. OF INTERNAL ACOUSTIC LINER ON SUPPLY AND RETURN AIR DUCTWORK

FROM ANY FCU, AHU, AC, OR RTU (UNO). PROVIDE 8LF INTERNAL LINER FOR

MIXING OR VAV BOXES.

4. PROVIDE FLEXIBLE CONNECTIONS AT THE INTAKE AND DISCHARGE OF ALL

MOTOR DRIVEN EQUIPMENT.

5. PROVIDE VIBRATION ISOLATORS FOR MOTOR-DRIVEN MECHANICAL EQUIPMENT.

6. ALL FLEXIBLE DUCTWORK SHALL HAVE A MAXIMUM DEVELOPED LENGTH OF (5)

FIVE FT.

7. CONTRACTOR SHALL REFER TO THE ARCHITECTURAL REFLECTED CEILING

PLANS FOR THE EXACT LOCATION OF ALL CEILING MOUNTED M/E/P DEVICES

INCLUDING BUT NOT LIMITED TO LIGHTS, DIFFUSERS, GRILLES ETC..

8. AIR DEVICE DUCT SIZES SHALL BE THE SAME SIZE AS SHOWN ON THE

DRAWINGS UNLESS NOTED OTHERWISE. REFER TO THE SCHEDULES FOR THE

CFM RANGES. PROVIDE A TRANSITION FROM THE NECK SIZE TO THE REQUIRED

DUCT SIZE SHOWN.

9. CONTRACTOR SHALL VERIFY THE EQUIPMENT CLEARANCE REQUIREMENTS

WITH THE MANUFACTURER'S RECOMMENDATIONS. EXACT LOCATION OF

SELECTED EQUIPMENT SHALL BE COORDINATED WITH THE STRUCTURE TO

PROVIDE RECOMMENDED CLEARANCES FOR MAINTENANCE.

10. PROVIDE FIRE DAMPERS, FIRE/SMOKE DAMPERS AND FIRE STOP AS REQUIRED

BY CODE AUTHORITIES FOR DUCT PENETRATIONS THROUGH FIRE OR SMOKE

RATED WALL AND CEILINGS. REFER TO ARCHITECTURAL DRAWINGS FOR WALL

TYPES.

11. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED MAINTENANCE

ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS AND VALVING.

12. SMOKE DETECTORS SHALL BE FURNISHED BY THE FIRE ALARM CONTRACTOR

AND WIRED BY THE ELECTRICAL CONTRACTOR. THE MECHANICAL CONTRACTOR

SHALL BE RESPONSIBLE FOR MOUNTING THE SMOKE DETECTOR IN THE

DUCTWORK AS SHOWN ON THE DRAWINGS AND IN ACCORDANCE WITH THE

MANUFACTURER'S PRINTED INSTRUCTIONS. DETECTORS SHALL BE PROVIDED IN

THE SUPPLY AND THE RETURN DUCTWORK (PRIOR TO MIXING WITH THE

OUTSIDE AIR) FOR ANY AIR HANDLING UNIT SYSTEM 2000 CFM SUPPLY AIR AND

ABOVE. THE DETECTOR SHALL BE HARDWIRED TO THE UNITS STARTER TO SHUT

DOWN THE FAN UPON DETECTION OF PRODUCTS OF COMBUSTION AS WELL AS

SEND A SUPERVISORY ALARM SIGNAL TO THE FIRE ALARM PANEL (IF PROVIDED -

IF NOT PROVIDE VISUAL/ AUDIBLE ALARM IN A SUPERVISORY/ APPROVED

LOCATION). FOR VAV SYSTEMS THE BMS SHALL DISABLE ASSOCIATED MIXING

BOX FANS UPON DETECTION OF SMOKE AT EITHER OF THE AHU'S SMOKE

DETECTORS. ENABLE MIXING BOX FANS UPON SMOKE SIGNAL CLEAR.

13. FINISH ALL EXPOSED TO VIEW DUCTWORK AND WALL LOUVERS PER

ARCHITECTS RECOMMENDATIONS. ALL EXPOSED ROUND DUCT SHALL BE

INTERNALLY SEALED AND MANUFACTURED FROM SPIRAL WOUND PAINT GRIP

STEEL.

14. ALL FLOOR BRANCHES OF PIPE RISERS SHALL BE PROVIDED WITH SHUT OFF

VALVES AND DRAIN CONNECTION.

15. UNLESS OTHERWISE SHOWN, LOCATE ALL ROOM THERMOSTATS, HUMIDISTAT

AND CO2 SENSORS 4'-0" (CENTERLINE) ABOVE FINISHED FLOOR. NOTIFY THE

ARCHITECT/ ENGINEER OF ANY ROOMS WHERE THE ABOVE LOCATION CAN NOT

BE MAINTAINED OR WHERE THERE IS A QUESTION ON PROPER LOCATION.

16. DUCTWORK AND ITS CONSTRUCTION WILL BE GALVANIZED SHEET METAL AND

CONSTRUCTED ACCORDING TO THE LATEST SMACNA STANDARDS.

17. ALL DUCTWORK IS SHOWN IN SCHEMATIC FORM. DUCT RISES AND DROPS ARE

NOT SHOWN. PROVIDE OFFSETS AS REQUIRED TO MEET SPACE REQUIREMENTS

AND TO AVOID INTERFERENCE WITH OTHER TRADES. EACH TRADE SHALL BE

RESPONSIBLE FOR COORDINATION WITH OTHER TRADES.

18. PIPING IS SHOWN IN SCHEMATIC FORM. ROUTE PIPING AS REQUIRED FOR

CLEARANCE WITH STRUCTURAL CONDITIONS. COORDINATE WITH OTHER

TRADES AS REQUIRED. PIPING SHALL BE INSTALLED WITH ADEQUATE SLOPE AS

REQUIRED FOR EACH PARTICULAR SYSTEM.

19. DOUBLE NUT LOCK DOWN FOR MULTI-VANE DAMPERS INSTALLED IN HIGH

VELOCITY DUCTWORK/SMOKE REMOVAL DUCTWORK.

20. ALL RADIUS TURNS SHALL BE SMOOTH WALL WITH A RADIUS OF R = 1.5D.

21. ACCESS DOORS SERVING FIRE/SMOKE DAMPERS, SMOKE DAMPERS OR FIRE

DAMPERS SHALL BE IDENTIFIED WHERE EASILY READ BY A LABEL HAVING

LETTERS NO LESS THAN 1/2" IN HEIGHT READING "FIRE/SMOKE DAMPER",

"SMOKE DAMPER" OR "FIRE DAMPER".

ZONE DAMPERZD ZD

EXISTING CONDITIONS GENERAL NOTES

THE EXISTING CONDITIONS INDICATED IN THE CONTRACT DOCUMENTS WERE TAKEN FROM SITE OBSERVATIONS AND THE OWNER'S RECORD DRAWINGS (IF AVAILABLE). IT SHALL BE THE SOLE RESPONSIBILITY OF THE CONTRACTOR AND EACH SUBCONTRACTOR TO VISIT THE SITE PRIOR TO THE BID DATE AND ASCERTAIN THE EXACT CONDITIONS. HE SHALL NOTIFY THE ENGINEER IMMEDIATELY OF ANY ACTUAL CONDITIONS THAT ARE IN CONFLICT AND ADJUST HIS PROPOSAL ACCORDINGLY. AFTER THE BID DATE IT SHALL BE THE SOLE RESPONSIBILITY OF THE CONTRACTOR AND EACH SUBCONTRACTOR TO PROVIDE ADDITIONAL LABOR AND MATERIALS DUE TO EXISTING CONDITIONS WHICH MAY BE REQUIRED TO PROVIDE COMPLETE OPERABLE SYSTEMS AT NO ADDITIONAL COST

TO THE OWNER AND OR ENGINEER.

AIR DEVICE DESCRIPTION

X"Ø

XXX AIR DEVICE NECK SIZE

CFM

AIR DEVICE TAG

NOMINAL CFM

RANGE

UP TO 38

MECHANICAL DUCTWORK DESIGN GUIDELINES

OPTIONAL FOR CONTRACTOR SELECTION LOW VELOCITY SYSTEM DUCTWORK (SIZES IN INCHES)

OPTIONAL, NET CLEAR INSIDE DUCT SIZE, SELECTIONS NOMINAL

DIAMETERNO 1. NO 2. NO 3. NO 4. NO 5.

39 TO 50

51 TO 70

71 TO 90

91 TO 110

111 TO 160

161 TO 230

231 TO 320

321 TO 420

421 TO 540

541 TO 700

701 TO 850

851 TO 1000

1001 TO 1300

1301 TO 1500

1501 TO 1700

1701 TO 2000

2001 TO 2600

2601 TO 3500

3501 TO 4400

4401 TO 6000

6001 TO 7600

DO NOT EXCEED (IN ANY DIRECTION) ASPECT RATIOS OF MORE THAN FOUR TO ONE, UNLESS FULL LENGTH INTERNAL DIVIDERS ARE INCORPORATED. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO CONFIRM AND UTILIZE THE SIZE APPLICABLE TO THE ACTUAL AVAILABLE SPACE, BASED UPON THE OPTIONAL SELECTION SIZES AS LISTED ABOVE FOR LOW VELOCITY AIR DISTRIBUTION SYSTEMS, PRIOR TO THE FABRICATION OR INSTALLATION OF ANY DUCTWORK SYSTEMS. THE INITIAL SIZES THAT MAY BE INDICATED UPON THE DRAWINGS ARE

FOR GENERAL REFERENCE ONLY. ALSO PROVIDE OFFSETS AND TRANSITIONS AS NEEDED.

NOTE:

4 DIA.

4-1/2 DIA.

5 DIA.

5-1/2 DIA.

6 DIA.

7 DIA.

8 x 6-1/2

9 x 7-1/2

9-1/2 x 9

10 x 10

11 x 11

12 x 12

14 x 12

16 x 12

18 x 12

21 x 12

19 x 14

24 x 14

25 x 16

30 x 16

32 x 18

30 x 20

9 x 6

10 x 7

10 x 8-1/2

11 x 9

12 x 10

13 x 11

15 x 11

17 x 11

20 x 11

23 x 11

22 x 13

26 x 13

30 x 14

36 x 14

36 x 16

37 x 18

11 x 5

12 x 6

12 x 7

13 x 8

14 x 9

14 x 10

16-1/2 x 10

19 x 10

23 x 10

26 x 10

24 x 12

29 x 12

33 x 13

40 x 13

43 x 14

51 x 14

14 x 4

14 x 5

15 x 6

15 x 7

16 x 8

16 x 9

19 x 9

22 x 9

25 x 9

30 x 9

26 x 11

33 x 11

36 x 12

44 x 12

47 x 13

56 x 13

17 x 3-1/2

20 x 4

19 x 5

18 x 6

18-1/2 x 7

19 x 8

22 x 8

26 x 8

30 x 8

35 x 8

28 x 10

37 x 10

40 x 11

50 x 11

54 x 12

70 x 12

4 x 3-1/2

5 x 3-1/2

5 x 4

5 x 5

6 x 5

7 x 6

4-1/2 x 3

6 x 3

5 x 3-1/2

6-1/2 x 4

7-1/2 x 4

8-1/2 x 5

7 x 3

9 x 3

11 x 3

11 x 4

13 x 3-1/2

7601 TO 9000

9001 TO 11000

11001 TO 12000

12001 TO 14000

14001 TO 16000

30 x 25

35 x 25

44 x 25

47 x 26

48 x 28

35 x 22

40 x 22

40 x 28

50 x 24

52 x 26

38 x 20

45 x 20

50 x 22

56 x 22

56 x 24

43 x 18

50 x 18

60 x 18

62 x 20

61 x 22

60 x 14

60 x 16

70 x 17

70 x 19

70 x 21

CONNECT NEW TO EXISTING

DEMO TO THIS POINT

EAT ENTERING AIR TEMPERATURE

UNDERCUT DOORU

ALL MECHANICAL EQUIPMENT AND INSTALLATIONS SHALL CONFORM WITH THE

REQUIREMENTS OF THE 2024 INTERNATIONAL MECHANICAL CODE, THE 2024

INTERNATIONAL ENERGY CONSERVATION CODE, THE 2024 INTERNATIONAL

BUILDING CODE, STATE AND LOCAL AMENDMENTS, NATIONAL FIRE PROTECTION

ASSOCIATION, UNDERWRITERS LABORATORIES (OR ETL), AND ALL APPLICABLE

LOCAL CODES AND ORDINANCES AND ANY APPLICABLE OWNER STANDARDS.

PROJECT APPLICABLE CODES

CHILLED WATER SUPPLY

CHILLED WATER RETURN

CHS

CHR

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M0.00

LEGEND AND

GENERAL NOTES

- MECHANICAL

CRAC-1B

FPB1-1

FPB1-2

FPB1-3

FPB1-4

FPB1-5

FPB1-6

FPB1-7

FPB1-8

FPB1-9

FPB1-10

FPB1-11

VAV1-4

VAV1-5

VAV1-6

VAV1-7

VAV1-9

VAV1-3

VAV1-1

VAV1-2

VAV1-10

AHU1-1

FSNPlan

VAV1-8

CRAC-1A

VAV1-11

VAV

FIRE

CONTROLLERS

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.1AFIRST FLOOR PLAN - ADMIN01 SCALE: 1/8"=1'-0"

FLOOR PLAN -

ADMIN - FIRST

ALTERNATE

SA2-2

RA2-2

AHU2-2

FPB2-14

FPB2-13

FPB2-4

FPB2-3

FPB2-2

FPB2-1

FPB2-15

VAV2-1

VAV2-2

VAV2-7

VAV2-8

VAV2-9

VAV2-10

VAV2-11

VAV2-12

VAV2-13

VAV2-14 VAV2-15

FPB2-12

VAV2-19

FPB2-19

M1.8AM1.7A

M1.8AM1.7A

VAV2-7

CRAC 2

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.2A

FLOOR PLAN -

SECOND FLOOR PLAN NORTH - ADMIN - ALTERNATE01 SCALE: 1/8"=1'-0"

ADMIN - SECOND

SA2-1

RA2-1

FPB2-11

FPB2-10

FPB2-9

FPB2-8

FPB2-7

FPB2-6

FPB2-5

VAV2-2

VAV2-3

VAV2-4

VAV2-6VAV2-7

VAV2-14

VAV2-16

VAV2-17

VAV2-15

FPB2-16

FPB2-17

FPB2-18

VAV2-5

VAV2-18

M1.8AM1.7A

M1.8AM1.7A

AHU2-1

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.3A

FLOOR PLAN -

SECOND FLOOR PLAN SOUTH - ADMIN - ALTERNATE01 SCALE: 1/8"=1'-0"

ADMIN - SECOND

SA3-2

RA3-2

FPB3-2

FPB3-3

FPB3-4

FPB3-16FPB3-17

FPB3-18

FPB3-19

VAV3-1

VAV3-2 VAV3-3

VAV3-4

VAV3-8

VAV3-9

VAV3-10

VAV3-11

VAV3-13

FPB3-1

VAV3-17

CRAC-3

VAV3-12

M1.10AM1.9A

M1.10AM1.9A

AHU3-2

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.4ATHIRD FLOOR PLAN NORTH - ADMIN - ALTERNATE01 SCALE: 1/8"=1'-0"

FLOOR PLAN -

ADMIN - THIRD

SA3-1

FPB3-5

FPB3-6

FPB3-7

FPB3-8

FPB3-9

FPB3-10

FPB3-11

FPB3-12

FPB3-13

FPB3-14FPB3-15

VAV3-4

VAV3-5

VAV3-6

VAV3-7

VAV3-8

VAV3-14 VAV3-15

VAV3-16

RA3-1CRAC-3

M1.10AM1.9A

M1.10AM1.9A

AHU3-1

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.5ATHIRD FLOOR PLAN SOUTH - ADMIN - ALTERNATE01 SCALE: 1/8"=1'-0"

FLOOR PLAN -

ADMIN - THIRD

SA4-1

RA4-1

AHU4-1

FPB4-1

FPB4-2

FPB4-3 FPB4-4

FPB4-5

FPB4-6

FPB4-7

FPB4-8

FPB4-10

FPB4-9FPB4-11FPB4-12FPB4-13

FPB4-14

FPB4-15

VAV4-1

VAV4-2

VAV4-3

VAV4-4

VAV4-5

VAV4-6VAV4-7

VAV4-8

VAV4-9

VAV4-10

VAV4-11VAV4-12

VAV4-13

VAV4-14

VAV4-15

EF-1

FC4-1

ABOVE

DOOR

FC4-2

ABOVE

DOOR

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.6AFOURTH FLOOR PLAN - ADMIN - ALTERNATE01 SCALE: 1/8"=1'-0"

FLOOR PLAN -

ADMIN - FOURTH

FCU-1

FCU-2

OUTDOOR

AIR

(SOUTH)OUTDOOR

AIR

(NORTH)

GENERAL NOTES

DESIGNATES EQUIPMENT.

1. COORDINATE WITH ALL TRADES BEFORE INSTALLING ANY EQUIPMENT.

2. LOCATE ALL MECHANICAL EQUIPMENT FOR UNOBSTRUCTED

MAINTENANCE ACCESS FOR ALL UNIT ACCESS PANELS, CONTROLS, AND

VALVING.

3. PROVIDE ALL MATERIALS AND EQUIPMENT AND PERFORM ALL LABOR

REQUIRED TO INSTALL COMPLETE AND OPERABLE MECHANICAL SYSTEM

AS INDICATED ON THE DRAWINGS AS SPECIFIED AND AS REQUIRED BY

ALL NATIONAL, STATE, AND LOCAL CODES.

4. ALL EXISTING SYSTEM INFORMATION AND/OR LOCATIONS ARE PROVIDED

BY THE OWNER. IT IS THE CONTRACTORS' RESPONSIBILITY TO VERIFY

ALL MEP SERVICES ARE LOCATED AS DESIGNED BEFORE BIDDING THE

PROJECT. IN OCCURRENCES WHERE EXISTING DOES NOT MATCH

DESIGNED, IT IS THE CONTRACTORS' RESPONSIBILITY TO NOTIFY THE

OWNER, ARCHITECT, & ENGINEER BEFORE PROCEEDING. IF ANY

DISCREPANCIES ARE NOT IDENTIFIED AT BIDDING, THE COST SHALL BE

ABSORBED BY THE CONTRACTOR AND NOT PASSED ONTO THE OWNER

OR ENGINEER OF RECORD.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH THE LATEST

EDITION NATIONAL ELECTRIC CODE SPECIFICATIONS. REPLACE WIRE IF

CURRENT WIRE IS DAMAGED OR NON-COMPLIANT.

6. THE MECHANICAL SERVICE TO AREAS NOT WITHIN THE DEMOLITION

SCOPE OF WORK SHALL NOT LOSE FUNCTION UNLESS SCHEDULED AND

AGREED TO BY THE OWNER.

7. ALL DEMOLITION ACTIVITIES SHALL BE PERFORMED SO AS TO PROVIDE

MINIMAL DISRUPTION TO THE NEIGHBORING TENANTS.

GENERAL NOTES

DESIGNATES EQUIPMENT.

Te xa s Re g is te re d F irm N

W e st

TH

S t.

Su it e

Pl a no

7.

Em e ng c a m d

-e ng

.c o m Pr o je c t N um b e r:

Revisions:

Sheet No.

C ol lin C o.

B

A S

U pg ra de

F or

M cK in ne y, T ex as

B lo om da le R oa d

Ja ck

H at ch el A dm in ist ra tio n

Bu ild in g

M1.7AROOF PLAN - ADMIN - ALTERNATE01 SCALE: 1/8"=1'-0"

ROOF PLAN -

ADMIN -