PGC03425 Interim Changes.pdf

Trousers, Men's, Dress, Polyester/wool, shall be made in accordance with GL-PD 07-05C (Class 1,Style 1) dated 4 March 2009.

Pattern date: 5 August 2010

Standard sample of cloth, serge, 60% polyester/40% wool, Army blue shade 451, is available and applicable for shade only under roll number 3800

Cloth shall be in accordance with type III, class 4 of MIL-DTL-823

ACCEPTABILITY OF LOTS SHALL BE DETERMINED BY THE USE OF "SAMPLING

PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES",

ANSI/ASQC Z1.4

GENERAL INSPECTION LEVEL 2

AQL's FOR PURCHASE DESCRIPTION

END ITEM DIMENSIONAL 4.0

VISUAL 6.5

INTERIM SPECIFICATION CHANGES TO GL-PD 07-05C:

PAGE 6, Paragraph 3.5.2: Delete in its entirety and substitute the following:

"3.5.2 Hook and eye. The hook and eye for waistband closure shall be Industrial Machining and Design Services, Inc. Part No. IMDSDS-008 (#8 nickel plated hook) and Part No.IMDSDS-085 (#85 nickel plated eye);

Metalform Part No. 1666 (H49/E50 complete set); YKK Snap Fasteners America Part No. 829-0000-310 (#8 Hook), Part No. 830-0000-310 (#85 Eye), Part No.

PF5-0000-340 (#8 Hook Plate), and Part No. PF6-000-340 (#85 Eye Plate) available from Snapco Manufacturing Corporation, or equal. The finish of both components shall be nickel plate (see 6.8). Prior to the use of an "or equal" item, the contractor shall submit the item with supporting data to the contracting officer for approval."

Page 7, Para 3.5.4.1 Machine thread. Delete the first line and replace with the following: "The thread for automatic machine pocket construction shall be Type I, Tex size 50, 3-ply of A-A-50199.".

Page 7, Paragraph 3.5.7, delete in its entirety and substitute the following:

3.5.7 Permanent creases. The trousers shall have permanent silicone creases (see 6.6). Each pair of trousers shall have a single continuous 1/16 +1/32, -0 inch silicone adhesive non-staining bead applied to the back side of the basic material in the center of each of the four prepressed leg creases to form permanent creases. Each bead shall be applied evenly and equally from the top of the crotch to within 2(+-1/4)inches of the unfinished trouser bottom. There shall be be no variation in the sharpness of the creases at front and back parts of the legs. Where resin misses the crease for any reason, it should be re-applied into the crease. The resin may extend beyond the crease at the top of front and back crease by 2 inches without having to be cleaned.

When the resin extends more than 2 inches it shall be cleaned by the manufacturer. Also any spot of resin less than 1/4 inch in diameter on the back side of the material does not have to be cleaned. The finished permanent creases shall show no evidence of flaking, decomposition, failure to retain creases, cracking, staining, strike back onto face of material or increased stiffness. The trousers shall have a minimum rating of "3" when evaluated for permanent crease resistance to dry heat (3 exposures) in accordance with AATCC 117, at a maximum of 400°F, and steam pressing and perchlorethylene solvent (3 exposures) in accordance with

AATCC 132.

Page 8, Paragraph 3.6, at the end of the paragraph add the following:

"Each pair of trousers shall contain a DLA Exclusive woven label."

Page 9, After Paragraph 3.6.4 insert the following Paragraph: "3.6.5 DLA Exclusive Woven Label. The jacquard woven Exclusive label shall specify "Made exclusively for Defense Logistics Agency" and shall include "by" and the contractor's name. The label shall be sewn on the inside of the left back pocket to finish between the bottom of the trouser curtain and the top of the welt stitching. The label shall face the wearer. The proposed finished label's design shall be submitted to the contracting officer for approval. " PAGE 11, Paragraph 3.9.1.7, line 3: Delete "outside" and substitute "inside".

PAGE 12, Paragraph 3.9.4.2, at end of paragraph: Add "The waistband shall be mitered in accordance with the waistband pattern piece.".

PAGE 12, Paragraph 3.9.4.4, line 6: Delete "1/2 inch" and substitute "1/4 inch". Line 3, after "1/16 inch from seam and": Add "for Class 1 only".

PAGE 12, Paragraph 3.9.4.5, line 2, after "is closed.": Add "The distance of the J-stitch shall be 1-3/8 + 1/16 inches.".

Add the following to the end of the paragraph: "The left fly shall be trimmed in accordance with the notch on pattern."

PAGE 13, Paragraph 3.9.4.6: Add the following to the end of the paragraph: "The hip pocket bags shall be made to conform to the shape shown on Figure 3."

PAGE 13, Paragraph 3.9.4.8, line 3: Delete "as indicated on pattern;" and substitute "centered between center front and side seam (see Figure 1).".

PAGE 13, Paragraph 3.9.4.10, line 1, after "(1/4 inch": Delete "off".

PAGE 16, Table V, under "1/2 hip" for size "44A": Delete "27-1/2" and substitute "27".

PAGE 19, Paragraph 6.4: Line 3, delete from "through http://warfighter.dla.mil" to end of paragraph. Insert "at http://www.troopsupport.dla.mil/Portal/sreqfrm.aspx."

PAGE 19, Paragraph 6.6:

Line 3, after "2": add "(+-1/4)", Lines 4-5, after "1/16": Delete "(nominal)" and substitute "+1/32, -0".

Pages 19-20, 6.6.2: Delete with no substitute.

Page 20, Add new Paragraph 6.7: Hook and eye suggested sources of supply.

A known source for Part Numbers IMDSDS-008 AND IMDSDS-085 is Industrial Machine and Design. 2007 South Avenue, Youngstown, OH 44502-2245, http://www.imds-ohio.com. A known source for Part Number 1666 is Metalform Co, Inc., 555 John Downey Drive, New Britain, CT 06051, http://www.metalformcompany.com. A known source of supply for Part Numbers 829-0000-310, 830-0000-310, PF5-0000-340 and PF6-0000-340 is Snapco Manufacturing Corporation, 140 Central Avenue, Hillside, N.J.

07205, http://snapcofasteners.com/."

Page 20, Paragraph "6.7 Subject terms (key words) listing", Delete Paragraph number "6.7" and substitute "6.8".

Suggested Sources for Silicone creasing: Supercrease, Inc (formerly Lintrak) 7454 Yonie Ct Las Vegas, NV 89117-2161 Phone: (310) 994-6488 Toll free: (702) 500-0145 Email: mailto:chris@supercrease.com CREASET INC, 4276-5 Industrial Pl. Island Park, NY 11558 Phone: (516) 897-4583

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE

FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR

PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD

BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH

TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A

HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND

READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT

CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST

APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM

TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE

ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S

LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL

PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN

APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE

SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE

TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO

STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE

FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE

SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT

AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE

SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

ADDITIONAL INFORMATION FOR MIL-STD-1488:

PAGE 2, PARAGRAPH 4, UNDER "DOCUMENT" DELETE "MIL-T-43654...ARCTIC" AND

SUBSTITUTE "CO/PD-99-19 CLASSIFICATION U TROUSERS, SNOW CAMOUFLAGE,

WHITE"

INTERIM CHANGES TO MIL-STD-1488G:

PAGE 21 DEFECT XXX. POCKET OR FLAP., PARAGRAPH "A" AT THE END OF THE

PARAGRAPH DELETE IN IT'S ENTIRETY AND SUBSTITUTE:

D SD U

1. MORE THAN 1/2 INCH * 3 2

2. MORE THAN 1/4 UP TO 1/2 INCH 3 3 2

3. MORE THAN 1/8 UP TO 1/4 INCH 2 2 1

PAGE 6, TABLE I DELETE IN ITS ENTIRETY AND SUBSTITUTE "TABLE I SAMPLING

PROVISIONS FOR END ITEM VISUAL EXAMINATION OF DRESS (D) TROUSERS:

NORMAL INSPECTION:

LOT SIZE SAMP SZ MAX ACC MAX ACC PT VALUE

NUM FOR

SELECTED

DEFECTS

(SEE 1.2)

UP THRU 90 20 0 3 PT 6 PT

91 THRU 150 32 0 5 PT 9 PT

151 THRU 280 50 0 7 PT 13 PT

281 THRU 500 80 0 9 PT 17 PT

501 THRU 1200 125 1 14 PT 25 PT

1201 THRU 3200 200 1 18 PT 33 PT

3201 THRU 10,000 315 2 24 PT 48 PT

10,001 THRU 35,000 500 3 35 PT 72 PT

35,001 AND OVER 800 5 55 PT 110 PT

TIGHTENED INSPECTION:

UP THRU 150 32 0 2 PT 5 PT

151 THRU 280 50 0 3 PT 7 PT

281 THRU 500 80 0 5 PT 11 PT

501 THRU 1200 125 1 9 PT 17 PT

1201 THRU 3200 200 1 13 PT 26 PT

3201 THRU 10,000 315 2 20 PT 39 PT

10,001 THRU 35,000 500 3 30 PT 59 PT

35,001 AND OVER 800 5 45 PT 89 PT

REDUCED INSPECTION:

UP THRU 280 20 0 2-6 PT 11 PT

281 THRU 500 32 0 3-9 PT 15 PT

501 THRU 1200 50 0 5-10 PT 18 PT

1201 THRU 3200 80 0 8-13 PT 24 PT

3201 THRU 10,000 125 1 12-17 PT 28 PT

10,001 THRU 35,000 200 1 17-21 PT 33 PT

35,001 AND OVER 800 2 23-29 PT 47 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND VALUE HAS NOT BEEN

EXCEEDED, ACCEPT THE LOT BUT REINSTATE NORMAL INSPECTION (SEE 6.4.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT VALUE.

TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE: "TABLE II SAMPLING

PROVISIONS FOR END ITEM VISUAL EXAMINATION OF SEMI-DRESS (SD) TROUSERS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

3&2 PT 3.2.&1 PT

DEFECTS DEFECTS

UP THRU 500 50 7 PT 14 PT

501 THRU 1200 80 9 PT 20 PT

1201 THRU 3200 125 14 PT 26 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 THRU 35,000 315 27 PT 57 PT

35,001 AND OVER 500 41 PT 85 PT

TIGHTENED INSPECTION:

UP THRU 500 50 3 PT 10 PT

501 THRU 1200 80 5 PT 15 PT

1201 THRU 3200 125 8 PT 23 PT

3201 THRU 10,000 200 12 PT 34 PT

10,001 THRU 35,000 315 19 PT 52 PT

35,001 AND OVER 500 27 PT 78 PT

REDUCED INSPECTION:

UP THRU 1200 32 3-8 PT 15 PT

1201 THRU 3200 50 5-9 PT 18 PT

3201 THRU 10,000 80 8-12 PT 24 PT

10,001 THRU 35,000 125 11-15 PT 31 PT

35,001 AND OVER 200 15-53 PT 43 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND VALUE HAS NOT BEEN

EXCEEDED, ACCEPT THE LOT BUT REINSTATE NORMAL INSPECTION (SEE 6.4.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT VALUE.

TABLE III DELETE IN ITS ENTIRETY AND SUBSTITUTE: "TABLE III SAMPLING

PROVISIONS FOR END ITEM VISUAL EXAMINATION OF UTILITY (U) TROUSERS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

3&2 PT 3.2.&1 PT

DEFECTS DEFECTS

UP THRU 500 50 9 PT 17 PT

501-1200 80 13 PT 20 PT

1201-3200 125 18 PT 29 PT

3201-10,000 200 25 PT 42 PT

10,001 & OVER 315 39 PT 62 PT

TIGHTENED INSPECTION:

UP THRU 500 50 5 PT 11 PT

501-1200 80 8 PT 17 PT

1201-3200 125 12 PT 25 PT

3201-10,000 200 19 PT 38 PT

10,001 & OVER 315 27 PT 57 PT

REDUCED INSPECTION:

3&2 PT /1 3,2&1 PT

UP THRU 1200 32 5-9 PT 16 PT

1201-3200 50 8-12 PT 20 PT

3201-10,000 80 11-14 PT 25 PT

10,001 & OVER 125 15-19 PT 29 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND VALUE HAS NOT BEEN

EXCEEDED, ACCEPT THE LOT BUT REINSTATE NORMAL INSPECTION (SEE 6.4.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT VALUE."

PAGE 26, UNDER "LABEL" DEFECT ADD THE FOLLOWING NEW DEFECT AND POINT

VALUES:

"C. BAR CODE LABEL/TAG. D SD U

1. NOT READABLE BY SCANNER 1 1 1

2. HUMAN READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE.

1 1 1

3. NOT VISIBLE ON FOLDED, PACKAGED ITEM. 1 1 1

4. CAUSES DAMAGE TO THE ITEM. 3 3 3

(ref. T0339 - May 22, 2006-REVISED)

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-

REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE"

AND "CLASS 1" INSERT "TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X -

CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH:

"2.1.3 OTHER PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS

DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE

ISSUES OF THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE THOSE LISTED IN THE

ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE

SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT LISTED IN THE DODISS SHALL BE

THE ISSUES OF THE NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE DATE OF

THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20

- FIBER ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED

TO AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC), P.O.

BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE

A CIRCULAR KNIT. WHEN SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE

NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1.

TYPE X1 SHALL BE STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF

CHAINSTITCHING IS SEWN IN THE MACHINE DIRECTION OF THE SUBSTRATE IN ORDER

TO REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE

AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW

TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING

CHAINSTITCH STITCH TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT

FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN

USED AS FUSIBLE SEAM TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24,

DELETE "45" AND SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND

3 DELETE "1600" AND SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER

LAUNDERING/DRY CLEANING). DELETE THE FIRST AND SECOND SENTENCES IN THEIR

ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE

FROM BOTH THE OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR CONTRACT USE

(SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE

STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL

PART FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL STABILITY AND ABRASION

RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE

FOLLOWING BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES,

OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED

TO DETERMINE IF DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

ADDITIONAL INFORMATION FOR A-A-50198A, THREAD, GIMP, COTTON, BUTTONHOLE:

NO ADDITIONAL INFORMATION FOLLOWS.

A-A-52094B Thread, Cotton dated 01 May 2019 No Additional Information (ref. T1481)

ADDITIONAL INFORMATION FOR ASTM-D-6193(2004)OR LATEST VERSION:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T8068 - May 18, 2006) MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY

MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA

TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF

C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO

BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)