SN-2023 -Gangway SH.pdf

GENERAL SPECIFICATIONS

CONSTRUCTION OF GANGWAY and ROTATING PLATFORM TURNTABLE

FOR THE NOAA SHIP BELL SHIMADA

1 SCOPE

1.1 This specification is for the construction of a gangway and rotating turntable for the NOAA Ship BELL SHIMADA.

2 REFERENCE DOCUMENTS

2.1 INTERNATIONAL MARITIME ORGANIZATION MSC.1/Circ.1331 – Guidelines for construction, installation, maintenance and inspection/survey of means of embarkation and disembarkation.

2.2 ISO 5488:1979, Shipbuilding – accommodation ladders.

2.3 ISO 7061:1993, Shipbuilding – aluminum shore gangways for seagoing vessels.

2.4 ISO 7364:1983 Shipbuilding and marine structures –deck machinery – accommodation ladder winches.

2.5 Drawing SH2023-002 - Gangway Details

2.6 Drawing – NOAA Turntable Design

2.7 Drawing - USN Turntable Designs

3 GOVERNMENT FURNISHED MATERIAL (GFM)

3.1 None

4 REQUIREMENTS

4.1 General Requirements

4.1.1 The contractor shall perform all work in accordance with the requirements the documents cited in paragraph 2 above.

4.1.2 The structure of the gangway, fittings and attachments should be such as to allow regular inspection, maintenance of all parts and, if necessary, lubrication of their pivot pin.

Special care should be taken to ensure that the welding connection works are properly performed.

4.1.3 The gangway and turn table shall be constructed from marine grade aluminum alloy

5086.

4.1.4 All fasteners shall be CRSS 316 and have appropriate isolation barriers.

4.1.5 All joints shall be welded unless specified.

4.2 Gangway Requirements

4.2.1 The gangway shall be a beam type with a safe working load (SWL) of 850lbs and have the following dimensions:

Length 24 feet Width 28 inches (clear opening)

4.2.2 The gangway railings and stanchions shall be made of 2” schedule 40 aluminum pipe.

Stanchions shall be mounted into sockets to allow removal. The sockets shall have a mechanical means to hold the stanchions in place. The sockets shall be bolted to the beam to allow for removal when damaged. A small drain hole shall be made in each socket to allow for drainage.

4.2.3 The gangway tread will be flat and made from an extruded material that provides traction when wet (figure 1).

4.2.4 The gangway shall have four lifting pad eyes and line cleats as indicated in the attached drawing. Lifting plates shall be 5 inches long and made from 4“ x ½ “ aluminum plate. A one inch hole with a doubler shall be provided in the middle of each pad eye.

4.2.5 The shore end of the gangway shall have two 5 “pad eyes with rounded corners as indicated in the drawing. Pad eyes shall be made from ½” aluminum plate. A one inch hole shall be provided in the middle of each pad eye. No wheels or rollers are required

4.2.6 The ship end of the gangway shall have an addition cap of ½ “aluminum plate with 4 5” rounded pad eye tabs. The outboard tabs shall be notched and mate with a correct ponding pipe on the pedestal. The inboard tabs shall have a 1” hole to allow the placement of a rod securing the gangway to the pedestal.

4.2.7 The shore side end of the gangway railing shall have closed rails.

4.2.8 The gangway shall be clearly marked at each end with a plate showing the restrictions on the safe operation and loading, including the maximum and minimum permitted design angles of inclination, design load, maximum load on bottom end plate, and test date. If the maximum operational load is less than the design load, it should also be shown on the plate.

4.3 Rotating Platform Turntable Requirements

4.3.1 Fabricate/supply a platform turntable per references 2.6 and 2.7.

4.3.2 The platform turntable shall be sized to accommodate the width of the attached gangway.

4.3.3 The platform turntable shall be attached to the ship structure and hinged to allow stowage in the upright (vertical) position.

4.3.4 The turntable shall have a pivoting support bracket (yoke) that attaches to ship structure when deployed in the horizontal position. (Figure 2)

4.3.5 The Platform turntable and yoke assembly weights shall be the minimum necessary to meet the design requirements.

4.4 Testing

4.4.1 The gangway shall be load tested per the references in section 2. Test date and weight shall be included on the reference plate indicated in section 4.2.7.

5 QUALITY ASSURANCE

5.1 None

6 NOTES

6.1 Figures

Figure 1 – Typical nonskid tread

Figure 2 – Typical Pedestal Support

1 ft 1 ft

12 ft

24 ft

28”

12”

42”

32”32” 5 ft 6” 5 ft 6”

4” angle pad eyes, ½ inch thick with 1” hole centered, 32 “ from each end (both sides).

2” stations, removable, mounted on side of beam.

Line Cleats attached to beam (both sides)

2” railings closed looped on shore end.

Two 5” square pad eyes, ½ inch thick with 1” hole centered on shore end (both sides).

Four 5” square pad eyes, ½ inch thick with 1” hole centered for attachment to pedestal. Outboard pad eyes shall be open to allow mating with the turntable.

SH2023 - Gangway Details

These markings were applied by JEDMICS on 02-DEC-2008 and supersede any other sensitivity markings on this document. Do not scale off this document; document not to any scale.

DISTRIBUTION STATEMENT C: Distribution authorized to U.S. Government agencies and their contractors; Critical Technology. Other U.S. requests for this document shall be referred to Supervisor of Shipbuilding, Conversion and Repair, Gulf Coast.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec. 2841 et seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App 2401, et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate per the provisions of OPNAVINST 5510.161.

DESTRUCTION NOTICE: This document may be destroyed by any means that will prevent disclosure of contents or reconstruction of the document.

2255404, 80064, DW, C, 0001, 0001

These markings were applied by JEDMICS on 02-DEC-2008 and supersede any other sensitivity markings on this document. Do not scale off this document; document not to any scale.

DISTRIBUTION STATEMENT C: Distribution authorized to U.S. Government agencies and their contractors; Critical Technology. Other U.S. requests for this document shall be referred to Supervisor of Shipbuilding, Conversion and Repair, Gulf Coast.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec. 2841 et seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App 2401, et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate per the provisions of OPNAVINST 5510.161.

DESTRUCTION NOTICE: This document may be destroyed by any means that will prevent disclosure of contents or reconstruction of the document.

2255404, 80064, DW, C, 0003, 0001

These markings were applied by JEDMICS on 02-DEC-2008 and supersede any other sensitivity markings on this document. Do not scale off this document; document not to any scale.

DISTRIBUTION STATEMENT C: Distribution authorized to U.S. Government agencies and their contractors; Critical Technology. Other U.S. requests for this document shall be referred to Supervisor of Shipbuilding, Conversion and Repair, Gulf Coast.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec. 2841 et seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App 2401, et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate per the provisions of OPNAVINST 5510.161.

DESTRUCTION NOTICE: This document may be destroyed by any means that will prevent disclosure of contents or reconstruction of the document.

2255404, 80064, DW, C, 0004, 0001

These markings were applied by JEDMICS on 02-DEC-2008 and supersede any other sensitivity markings on this document. Do not scale off this document; document not to any scale.

DISTRIBUTION STATEMENT C: Distribution authorized to U.S. Government agencies and their contractors; Critical Technology. Other U.S. requests for this document shall be referred to Supervisor of Shipbuilding, Conversion and Repair, Gulf Coast.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec. 2841 et seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App 2401, et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate per the provisions of OPNAVINST 5510.161.

DESTRUCTION NOTICE: This document may be destroyed by any means that will prevent disclosure of contents or reconstruction of the document.

2255404, 80064, DW, C, 0005, 0001

These markings were applied by JEDMICS on 02-DEC-2008 and supersede any other sensitivity markings on this document. Do not scale off this document; document not to any scale.

DISTRIBUTION STATEMENT C: Distribution authorized to U.S. Government agencies and their contractors; Critical Technology. Other U.S. requests for this document shall be referred to Supervisor of Shipbuilding, Conversion and Repair, Gulf Coast.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec. 2841 et seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App 2401, et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate per the provisions of OPNAVINST 5510.161.

DESTRUCTION NOTICE: This document may be destroyed by any means that will prevent disclosure of contents or reconstruction of the document.

2255404, 80064, DW, C, 0006, 0001

These markings were applied by JEDMICS on 02-DEC-2008 and supersede any other sensitivity markings on this document. Do not scale off this document; document not to any scale.

DISTRIBUTION STATEMENT C: Distribution authorized to U.S. Government agencies and their contractors; Critical Technology. Other U.S. requests for this document shall be referred to Supervisor of Shipbuilding, Conversion and Repair, Gulf Coast.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec. 2841 et seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App 2401, et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate per the provisions of OPNAVINST 5510.161.

DESTRUCTION NOTICE: This document may be destroyed by any means that will prevent disclosure of contents or reconstruction of the document.

2255404, 80064, DW, C, 0002, 0001