NGCE-RAM-20250512.pdf
PDF 57 KB Posted
- Attached to
- LOAD FRAMES Federal contract opportunity
- Solicitation number
- N0017326Q5217
About this file
This is a technical engineering drawing for a frame leg component manufactured by the U.S. Naval Research Laboratory located at Trumbo Point Annex, Building F15, Key West, Florida. The drawing (NGCE-RAM-20250512, Revision A) specifies a 6.0 x 6.0 x 0.5 inch aluminum extrusion made from 6061-T6 aluminum with clear anodize finish coating. The component features 24 holes of 0.640 inches diameter tolerance (+0.006/-0.001 inches) drilled through both sides, 32 additional 0.640-inch diameter holes through both sides with the same tolerance, and two 5/16-18 UNC threaded holes with 0.36-inch diameter countersinks at 90 degrees on the near side. Geometric dimensioning and tolerancing (GD&T) conforms to ASME Y14.5-2009 standards, with general tolerances of ±0.1 inches for single decimals, ±0.03 inches for two decimals, ±0.010 inches for three decimals, and ±5.0 degrees for angular dimensions.
The drawing is model-based, requiring reference to the solid model for complete dimensional information. All dimensional requirements shown on the drawing field must be inspected. Burrs must be removed and sharp edges broken per standard practice. The drawing is released and references the Product Data Management (PDM) system for responsible engineer and approval documentation. Scale is 1:10 with sheet 1 of 1 displayed.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| NGCE-RAM-20250525.pdf | ||
| Solicitation - N0017326Q5217.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
24X .640+ .006 .001
THRU BOTH SIDES
32X .640+
.006 .001
THRU BOTH SIDES
.020 B A C .010 B
.030 A B C
.010 A
A
2X 5/16-18 UNC THRU
.36 X 90°, NEAR SIDE 2X 5/16-18 UNC THRU
.36 X 90°, NEAR SIDE.030 A B C
.010 A
.030 A B C
.010 A
B
C
6.0 x 6.0 x .5 EXTRUSION
THIS IS A MODEL-BASED DRAWING. REFER TO SOLID MODEL FOR ALL DIMENSIONS. UNLESS 1.
OTHERWISE SPECIFIED ON THE FIELD OF THE DRAWING.
DIMENSIONAL REQUIREMENTS ON THE FIELD OF THE DRAWING SHALL BE INSPECTED.2.
UNLESS OTHERWISE SPECIFIED
APPLIES.3.
REMOVE BURRS AND BREAK SHARP EDGES.4.
D
C
B
AA
B
C
D
12345678
8 7 6 5 4 3 2 1
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
X.X 0.1
X.XX 0.03
X.XXX 0.010
ANGULAR: 5.0
TITLE:
SIZE
B
DWG. NO. REV
WEIGHT: SCALE: 1:10
A
SHEET 1 OF 1
TRUMBO POINT ANNEX
BUILDING F15
KEY WEST, FL 33041
LEG, FRAME
NGCE-RAM-20250512
Released
SEE PDM FOR
RESP. ENGR.
AND APPROVALS
GD&T IN ACCORDANCE
WITH: ASME Y14.5-2009
COAT
FINISH
MATERIAL 6061-T6 ALUMINUM EXT.
CLEAR ANODIZE
| Sheet1 |
| Drawing View1 |
| Drawing View2 |
| Drawing View3 |
File details come from the government source that posted it. Updated .