newark school 10317 Paving Services Set Aside for MBE_ WBE and or SBE FINAL.pdf

PDF 8 MB Posted

Attached to
Paving Services Set Aside For Minority Business Enterprise (mbe) And/or Women Owned Business Enterprise (wbe) And/or Small Business Enterprise (sbe)
Solicitation number
10317
Issued by
Essex County, New Jersey

About this file

This is a Request for Bid (RFB) solicitation document issued by the Newark Board of Education's Department of Purchasing for paving services. The solicitation, numbered 10317, was issued on October 29, 2026, and seeks paving services including inspection, patching, repair, resurfacing of bituminous paving, and installation of interlocking pavers at Newark Board of Education facilities throughout Newark, New Jersey. The work encompasses both labor and materials for site preparation, base course installation, and surface finishing in compliance with specified standards. The pre-submission virtual meeting was scheduled for November 4, 2026, at 10:00 a.m. EST, with a bid submission deadline of 12:00 p.m. EST on Thursday, November 19, 2026. All bids must be submitted electronically through the npssourcing.com platform. The contract term is two years from the date of award, with an option to renew for one additional two-year period, creating a potential maximum contract term of four years. The anticipated initial contract period runs from January 1, 2027, through December 31, 2028.

This is a 100 percent set-aside for Minority Business Enterprise (MBE), Women's Business Enterprise (WBE), and/or Small Business Enterprise (SBE) bidders, with valid certifications required at time of bid submission. Award will be made to the lowest responsive and responsible bidder. All pricing must be firm with no increases permitted during the contract period, and prices must include labor, travel time, mileage, and tolls. Contractors must possess a valid New Jersey Public Works Contractor Registration Certificate and comply with New Jersey Prevailing Wage Act requirements, with minimum wage rates established by the New Jersey Department of Labor and Workforce Development. Site visits are required at no cost to the District for generation of job-specific quotes. Contractors must maintain comprehensive general liability insurance with minimum limits of $1,000,000 combined single limit, workers' compensation insurance as required by state law, commercial automobile liability insurance with $1,000,000 minimum limits, and umbrella liability coverage of not less than $5,000,000. The contract is not funded independently; funding is provided through purchase orders issued by the Purchasing Agent, and the District has no minimum expenditure obligations.

View the file

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

Attention Bidders Electronic Bidding Tutorial Videos Are Available Via https://www.nps.k12.nj.us/departments/purchasing/view-current-bids/

All bids will be received electronically via our electronic bidding platform https://npssourcing.com/ . Email Karen Blessing for user credentials via kblessing@nps.k12.nj.us

Bidders are encouraged to attend the virtual pre-submission meeting on Wednesday, November

4, 2026, 10:00 a.m. EST to review completion of the required documents and the electronic submission process. Virtual meeting credentials are below.

Webex Link: https://nboe.webex.com/

Meeting Number: 2862 665 3939

Password: iRvQnCHm842

Dial In: (646) 992-2010

All questions shall be submitted in writing via the bidding platform prior to 2:00 p.m. EST

Wednesday, November 4, 2026. The specific section and page number to which each question refers is to be indicated. Answers will be provided at least seven days prior to the acceptance of bids.

Bidders are required to submit pricing via the Pricing - Enter Bids section.

Bidders are required to upload their signed and complete bid with all required documents and signatures in the Questionnaire - Answers Questions section. The complete bid must be submitted prior to 12:00 p.m. EST Thursday, November 19, 2026 via https://npssourcing.com/

Bids will be publicly opened and announced directly after the submission deadline. Virtual meeting credentials are below.

Webex Link: https://nboe.webex.com/

Meeting Number: 2863 775 0469

Password: iUjEKrBY733

Dial In: (646) 992-2010

Attention Bidders

This is a Set-Aside Bid for: 100% Minority Business

Enterprise (MBE), and/or Women Business

Enterprise (WBE), and/or Small Business

Enterprise (SBE)

Bidders shall include their valid certification with their bid.

Vendors wishing to apply for certification may contact:

NJ Division of Revenue and Enterprise Services

P.O. Box 628

Trenton, NJ 08645-0628 https://business.nj.gov/

This Bid will be opened electronically at 12:00 P.M. on

THURSDAY, NOVEMBER 19, 2026 SOLICITATION 10317

DESCRIPTION

PAVING SERVICES

SET ASIDE FOR MINORITY BUSINESS ENTERPRISE (MBE) AND/OR

WOMEN OWNED BUSINESS ENTERPRISE (WBE) AND/OR

SMALL BUSINESS ENTERPRISE (SBE)

TWO (2) YEAR CONTRACT WITH THE OPTION TO RENEW FOR ONE (1) ADDITIONAL TWO (2) YEAR PERIOD

The solicitation is

UNRESTRICTED SET-ASIDE

This is a ____% set-aside for

SMALL MINORITY WOMEN OWNED

BUSINESS BUSINESS BUSINESS

FOR BIDDING PLATFORM CREDENTIALS EMAIL: KAREN BLESSING KBLESSING@NPS.K12.NJ.US

If you do not wish to respond, please identify why within the electronic bidding platform.

COMMENTS:

BIDDERS ARE REMINDED THAT THIS IS AN ELECTRONIC BID. THE NEWARK BOARD OF

EDUCATION UTILIZES EC SOURCING GROUP’S FLEX RFP ELECTRONIC BIDDING SYSTEM.

NO BID SURETY/BOND OR PERFORMANCE BOND REQUIRED.

ALL QUESTIONS MUST BE SUBMITTED IN WRITING VIA THE ELECTRONIC BIDDING PLATFORM

HTTPS://NPSSOURCING.COM/ PRIOR TO 2:00 P.M. WEDNESDAY, NOVEMBER 4, 2026. ANSWERS WILL

BE PROVIDED AT LEAST SEVEN DAYS PRIOR TO THE ACCEPTANCE OF BIDS.

PRICING MUST BE ENTERED ELECTRONICALLY VIA HTTPS://WWW.NPSSOURCING.COM/

ALL BID SUBMISSIONS MUST BE SUBMITTED PRIOR TO 12:00 P.M. EST, THURSDAY, NOVEMBER 19, 2026 VIA HTTPS://WWW.NPSSOURCING.COM/

Newark Board of Education Department of Purchasing

765 Broad Street Newark, New Jersey 07102-3091

SOLICITATION, BID OFFER AND AWARD

1. SOLICITATION NO. 10317 2. DATE ISSUED: Thursday, October 29, 2026

3. CONTRACT NUMBER: 4. CONTRACT PERIOD:

FROM ________________________________

TO:___________________________________

5. DESCRIPTION: PAVING SERVICES – SET ASIDE FOR MINORITY BUSINESS ENTERPRISE (MBE) AND/OR WOMEN OWNED BUSINESS ENTERPRISE (WBE) AND/OR SMALL BUSINESS ENTERPRISE (SBE) TWO (2) YEAR CONTRACT WITH THE OPTION TO RENEW FOR ONE (1) ADDITIONAL TWO (2) YEAR

PERIOD

6. BIDS SHALL BE SUBMITTED ELECTRONICALLY VIA THE BIDDING PLATFORM. YOUR BID MUST INCLUDE ALL REQUIRED DOCUMENTS AND A SIGNATURE IN BOX NUMBER 17. ALL BIDS ARE DUE PRIOR TO 12:00 P.M. THURSDAY, NOVEMBER 19, 2026 MODIFICATION AND WITHDRAWALS ARE

SUBJECT TO ALL TERMS AND CONDITIONS IN THIS SOLICITATION.

7. SUBMIT ALL QUESTIONS VIA THE BIDDING PLATFORM

8. TABLE OF CONTENTS

Solicitation Bid Offer and Award Subcontractor Disclosure Statement

Section C- General Specifications Prevailing Wages Certification

Section D-Special Conditions Lowest Bidder Prevailing Wage Certification

Signature of Bidder Contractor’s Registration Certification

Attachment A – Bidder’s Questionnaire Total Amount of Uncompleted Contracts

Political Contribution Disclosure Certification of Non-Debarment for Federal Government Contracts

Statement of Ownership Disclosure Initial Project Workforce Report (AA201)

Certification of Non ‐ Involvement in Prohibited Activities in

Russia or Belarus

AHERA Contractor Notification

Disclosure of Investment Activities in Iran Newark Board of Education Standard Terms and Conditions Construction

Non-Collusion Affidavit Mandatory Equal Employment Opportunity Language with

Newark Board of Education Vendor Set-Up Form State of New Jersey Department of Labor and Workforce Development Construction Contract Compliance

Equipment Certification Bid Checklist Certifications Prevailing Wage Rate Determination

BID AND OFFER (Must be completed by the bidder)

9. BIDDERS FEDERAL ID NO.

9A, BIDDER’S EMAIL

10. BIDDERS TELEPHONE NO.

11. DISCOUNT FOR PROMPT PAYMENT

(SEE SECTION E: PAR. 14)

12. N/A

13. N/A

14. The undersigned agrees, if this offer is accepted within 90 calendar days (90 calendar days unless a different period is inserted by the offerer) from the date of receipt of offer specified above, to furnish any or all items upon which prices are offered at the prices set opposite each item, delivered at the designated point(s) within the time specified in the schedule.

15. Signature by the bidder attests that she/he has read, understands, and agrees to all terms, conditions, and specifications set forth in the solicitation unless otherwise stated in writing and submitted in writing with his/her bid. Furthermore, signature by the bidder signifies that this is a contract immediately upon notice of award of contract by the School District for any or all of the items bid, and for the length of time indicated in the bid. Failure to accept a contract within the time period indicated by his/her proposal or failure to hold prices or to meet any other terms and conditions as defined in his/her bid during the term of the contract, shall constitute a breach and may result in suspension or debarment from further bidding to The Newark Board of Education. A defaulting contractor may also be liable, at the option of the School District, for the difference between his/her bid price and the price of an alternate source of supply.

16. DATE

17. SIGNATURE OF THE BIDDER (Must be signed)

(L.S.) x____________________________________

(Printed Name of Person Authorized to Sign Offer)

(Title)

18. COMPANY NAME

(Address: NO P.O. Box)

(City) (State) (Zip)

AWARD (To be completed by The Newark Board of Education)

19. Contract Value: _________________________________________

The District’s liability is limited to the dollar amount stated on the District’s purchase order/s issued by the Purchasing Agent.

20. Board Approval Date: ____________________________________________

Purchasing Department 765 Broad Street

Newark, New Jersey 07102-3091

INSTRUCTIONS TO BIDDERS FOR COMPLETING THIS PROPOSAL

1. Read the entire bid proposal, including all terms, conditions and specifications.

2. All bid prices shall be entered via https://npssourcing.com/ .

3. This bid proposal is to be signed in Box #17

4. Bid prices shall include delivery of all items. F.O.B. DESTINATION, FREIGHT

PREPAID or as otherwise provided.

5. Ensure all items listed in the enclosed checklist are complete and submitted.

FOR NEWARK BOARD OF EDUCATION USE ONLY

21. APPROVED AS TO COMPLIANCE WITH BIDDING REQUIREMENTS

Director of Support Services

Date:________________________________

22. REVIEWED AS TO LEGAL FORM

Newark Board of Education Counsel

23. SIGNATURE OF THE BOARD’S CONTRACTING AGENT: (Must be signed)

School Business Administrator

24. SIGNATURE OF THE BOARD’S CONTRACTING AGENT:

Board Chairperson (signature required if contract is valued over $53,000.)

25. Please provide the following employment statistical data.

Vendors that are classified as Small, Minority, or Woman-Owned business, please provide copies of your New Jersey Set-

A-Side certification.

This firm is a: Commercial_____ Non-Profit_____ Government Agency_____

This firm is a: Large_____ Small_____ (100 employees or less)

This firm is a: Woman owned business_____(51% or more of ownership is held by women)

This firm is a: Minority owned business_____ (51% or more of ownership is held by minorities)

If minority, please check (). Minority is defined as:

African American_____ Hispanic American_____

(Black racial groups in Africa) Spanish or Portuguese culture with origins in Mexico, South or Central America or Caribbean Islands)

American Indian or Alaskan Native _____ Asian American_____

(Origins North America) (Origins of the original people of the Far

East, Southeast Asia, the Indian Subcontinent, Hawaii or the

Pacific Islands)

Please check () the appropriate box:

Individual/Sole Proprietor Corporation Partnership Other

PERCENTAGE OF PERMANENT MINORITY/NON-MINORITY EMPLOYEE BREAKDOWN

MALES

FEMALES

TOTAL #

OF

EMPLOYEES

BLACK

HISPANIC

AMER.

IND.

ASIAN

NON-

MIN.

BLACK

HISPANIC

AMER.

IND.

ASIAN

NON-

MIN.

READ, REVIEW AND COMPLY

It is the bidder’s responsibility to read the entire document, review all enclosures and attachments, and comply with all requirements specified herein. Each bidder shall be deemed to have read and to be fully familiar with the bid/contract requirements and documents. Failure on the part of the bidder to familiarize themselves with the request for bid package shall not release them of their obligation to fulfill the services outlined.

SECTION C – GENERAL SPECIFICATIONS

C 1 SCOPE OF WORK

C1.1 The Contractor shall furnish all labor, supervision, materials, tools and equipment to perform paving services for the Newark Board of Education (NBOE, District) as specified under the terms and conditions subsequently set forth.

The Contractor shall use qualified, trained, and experienced personnel supervised by the Contractor.

C1.2 This work shall include all labor, equipment and materials necessary to inspect, patch, repair, repave (resurface), bituminous paving and/or install interlocking pavers to locations within Newark, New Jersey.

C1.3 Bidders shall be of known reputation and shall have sufficient qualified personnel and equipment to adequately administer the District’s paving needs.

C1.4 The awarded Contractor shall preform a site visit at no cost to the District for generating job specific quotes based on the contracted rate for each project. See section D5 for quotation requirements.

C1.5 A signed purchase order and written approval from a designated Facilities Management Representative is required prior to project commencement. All completed jobs shall be inspected and approved by Facilities Management prior to payment.

C1.6 A Newark Board of Education Facilities Management representative will coordinate all required maintenance visits with the Contractor as required. The Newark Board of Education will not be liable for any costs incurred by the vendor for work not approved by a Facilities Management representative.

C1.7 The school directory is available via https://www.nps.k12.nj.us/schools/ .

C1.8 The Contractor shall possess a valid New Jersey Public Works Contractor Registration Certificate, include a copy with your bid submission.

C1.9 Bidder must initial any alterations to the specifications.

C1.10 The Contractor shall remove dirt, gravel, sod and other debris from the existing pavement; followed by broom sweeping the pavement surface.

C1.11 Preparation shall be such that a smooth transition is obtained from newly paved areas to existing pavements.

C1.12 Contractor shall keep work area clean and safe. All debris must be removed from the premises. The contractor is required to ensure that all health and safety precautions are taken while affecting repairs.

C 2 PRECAST INTERLOCKING PAVERS

C2.1 Applicable services for interlocking pavers shall include furnishing and installation of materials. Product shall match existing materials when available. Substitutions must be approved in writing by the Executive Director of

Facilities Management.

C2.2 Installation procedures shall be in accordance with the product manufacturer’s recommendations.

C2.3 Job Conditions:

1. Protect adjoining work before work begins.

2. Substrate shall be firm, compacted, clean, and free from oil, curing compounds, grease, dirt, and waxy film.

3. Grounds, anchors, plugs, hangers, electrical work, and mechanical work in area to be paved shall be installed, tested, and accepted.

4. When measured in every direction, concrete substrate shall deviate not more than 3/16 inch from ten-foot straight edge.

C2.4 Storage and Handling:

1. Stockpile and handle setting sand to prevent contamination.

2. Store pavers off ground and cover; prevent staining and contamination.

C2.5 Contractor shall deliver extra pavers in a quantity not less than two percent of total amount of each kind, grade, and color of pavers installed.

C2.6 Pavers: Precast concrete, nonslip, as-cast (sandblasted) surface texture; conform to ASTM C936, compressive strength 8000 psi average minimum; absorption less than 5 percent (ASTM C140); thickness 2 3/8 (3 1/8) inches.

C2.7 Shape and color shall be determined by the Acting Executive Director of Facilities Management. Acceptable manufacturers: Paver Systems, Lithonia, GA or approved equivalent.

C2.8 Setting Sand: Manufactured or natural graded, washed, sharp sand 100 percent passing 3/8 sieve; maximum of 3 percent passing #200 sieve.

C2.9 Edge Restraint: One of the following:

1. Paver manufacturer’s precast curb

2. Concrete curb

3. Building Wall

C2.10 Joint Filler: Closed cell, polyethylene foam, top 2 skip-scored for removal, one side coated with pressure sensitive adhesive. Acceptable manufacturers:

1. W.R. Meadows, Ceramar.

2. Sonneborn Building Products, Chemrex Inc., Sonoflex F.

3. Progress Unlimited Inc., Skip Slit Joint Filler.

C2.11 Paver Sealer: Acrylic resin concrete sealer, as recommended by paver manufacturer must be installed as specified.

C2.12 Drainage Mat: Drainage system composite consisting of non-woven, needle punched filter fabric bonded to one side of a crush-proof drainage core; American Society for Testing and Materials (ASTM) D4439.

C2.13 Contractor shall examine substrate for defects and tolerances adversely affecting the execution and quality of the work before installation.

C2.14 Preparation:

1. Base course: Prepare and compact. Surface of base course shall be 3 1/8 inches below finished surface of paving for 2 3/8 pavers (3 7/8 inches for 3 1/8 pavers) with less than 3 tolerances.

2. Concrete surface: Clean substrate; install waterproofing membrane including protection board, and drainage mat in accordance with manufacturers printed instructions.

3. Edge restraint: Construct in accordance with the appropriate specification section and to tolerances and levels indicated.

4. Sand setting bed: Spread and screed sand to produce one-inch-thick laying course; do not disturb screeded bed before placing pavers.

C2.15 Installation:

1. Discard pavers with chips, cracks, discoloration, and other visible defects.

2. Cut units with saws designed to cleanly cut pavers. Unit edges shall be clean cut, sharp, and unchipped. Fit pavers neatly to adjoining work and in indicated pattern. Whenever possible, use uncut pavers. Do not use pieces smaller than one-half full size.

3. Install filler in indicated joints extending thru setting bed.

4. Vibrate laid pavers with flat-faced vibrator capable of producing 3000 to 5000 pounds compaction force.

5. Spread clean, dry sand over vibrated surfaces; re-vibrate and sweep until joints between pavers are filled.

6. Form isolation joints where indicated. Construct joints completely through pavers and setting bed. Unless otherwise indicated, joint shall be 3/8 inch wide.

C2.16 Tolerances:

1. Width of joints shall not vary more than 1/16 inch.

2. Flatness of installed pavers shall not vary more than plus 1/16 inch from a ten-foot straightedge.

3. Elevation over edge restraints shall not exceed 1/8 inch.

C2.17 Cleaning:

1. Remove construction debris; clean discolored paver faces in accordance with coating manufacturer’s printed instructions; do not use acid.

2. Sweep off excess extruded sand.

C2.18 Isolation Joints: Remove top part of joint filler and clean joint faces.

C 3 BITUMINOUS PAVING REPAIR AND RESURFACING

C3.1 Applicable services for bituminous paving shall cover furnishing and installation of materials, repair and resurfacing of bituminous pavements. Product shall match existing materials when available. Substitutions must be approved in writing by the Executive Director of Facilities Management.

C3.2 Asphaltic Concrete:

1. Hot-Mixed, Hot-Mixed Asphaltic Concrete and Emulsified asphalt shall comply with requirements of

ASTM D3515.

2. Plant-Mixed, Stockpiled Asphalt Cold Mixes shall comply with the requirements of the applicable Asphalt

Institute Binder Specifications.

C3.3 Bituminous Prime: Bituminous prime shall comply with ASTM D2027.

C3.4 Base Course: Base course material shall comply with New Jersey Department of Transportation (NJDOT) specification for dense-graded, high-quality material.

C3.5 Bituminous Tack Coat: Bituminous tack coat shall comply with ASTM D2027.

C3.6 Preparation of Areas for Patching:

1. Pot Holes: Trim the perimeter of each hole to a vertical face with a carborundum blade in a square or rectangular pattern at least 18 inches from ragged edge. Remove material to a depth that provides a uniform well compacted bottom surface. Remove all loose material resulting from trimming or otherwise existing in the hole. If subbase is disturbed, reestablish in a like manner to adjacent substrate. Areas to be repaired shall be dry before repair is started.

2. Alligator-Cracked and Rutted Areas: The pavement shall be sawed or cut with pavements breakers to a smooth vertical face 18 inches outside of the alligator-cracked area. Unsatisfactory material shall be removed in a manner not to disturb the sides of the excavated area.

3. Slippage Areas: Saw a rectangular area around the slippage area that overlaps into well-bonded material by at least 18 inches. The depth of the saw cut shall be equal to the thickness of the layer of material that is slipping. Slippage area shall be broomed clean and all loose material removed.

C3.7 Temperatures for asphalt material application shall comply with the Asphalt Institute and applicable ASTM standards.

C3.8 Base Course: Place base course material in layers not exceeding a compacted thickness of 6 inches. Compact each layer by mechanical compactors to a density of not less than the density of the corresponding layer of the adjacent pavement structure.

C3.9 Prime Coat: Prime base course with MC-7 liquid asphalt at a rate for 0.20 to 0.30 gallon per sq. yd. Bolt excess prime with sand before the surfacing material is applied.

C3.10 Tack Coat: Give the edges of existing asphaltic concrete or surfaces of Portland cement concrete and asphaltic concrete a tack coat of MC-70 liquid asphalt at a rate of 0.05 to 0.15 gallon per sq. yd. Allow the material to cure before placing the surfacing material.

C3.11 Hot Mixed Asphaltic Concrete: Place the material in layers not exceeding 2-1/2 inches in thickness and compact to a density equal to the density of the adjacent asphaltic concrete.

C3.12 Stockpiled Cold Mixes: The compact thickness of each layer of material shall not exceed 2 inches. Before compaction, the material shall be allowed to aerate until the proper amount of cohesion has developed to obtain adequate compaction. When more than one layer is used, each layer shall be thoroughly cured before the succeeding layer is placed.

C4 BITUMINOUS PAVING

C4.1 Description of Work: This specification covers furnishing and installation of asphaltic concrete overlays.

Products shall match existing materials when available. Substitutions must be approved in writing by the

Executive Director of Facilities Management. Installation procedures shall be in accordance with the product manufacturer’s recommendations. Demolition and removal of materials shall be as required to support the work.

C4.1a All asphalt paving work shall be provided by personnel with a minimum of five (5) years experience.

C4.2 Products:

C4.2a Asphalt Cement: The asphalt cement shall comply with ASTM D946 penetration grade 85-100 requirements and shall show a negative spot test when tested in compliance with AASHTO T 102.

C4.2b Mineral Aggregates: Shall comply with ASTM D3515 for ¾- inch maximum aggregate mix.

C4.2c Test Properties: The bituminous mixture shall meet the following requirements:

Stability minimum, lb. 500

Flow maximum, 1/100-in. units 20

Voids total mix, % 3-5

Voids filled with bitumen, % 75-85

4.3 Execution

C4.3a Preparation of Existing Surface: The Contractor shall raise and reset all structures such as manhole frames, valve boxes drainage structures, etc., to meet the required grade. An asphalt tack coat shall be applied to all contact surfaces in advance of the asphalt concrete overlay placement. The asphalt tack shall be placed at an asphalt residue coverage minimum rate of 0.05 gal/sq. yd.

C4.3b In sinkage areas and other locations where paving thickness required is in excess of 1 ½ inches the new asphaltic concrete surfacing shall be laid in two courses. The first course to be firmly compacted and leveled of 1 ½ inches below finished pavement surface and allowed to harden before application of the topping. Thoroughly clean and remove all loose and foreign material from existing pavement surfaces at base of new surface course.

C4.3c Plant Mixing: All ingredients shall be carefully weighed in the designated proportion. Aggregate moisture at time of mixing shall not exceed 0.5%. Temperature of mixture shall not exceed 326° F. at plant. All ingredients shall be heated so that mixture temperature at delivery to site is not less than 250° F. Asphalt shall be heated so that it will be sufficiently fluid to produce a uniform coating on every aggregate particle. Mixing shall continue until a uniform homogeneous completely coated mixture is obtained.

C4.3d Transportation of Mix: Transport mixtures in tight clean vehicles free of kerosene and other solvents and foreign materials. Provide covers to insulated vehicles as required to maintain specified mixture temperatures.

C4.3e Depositing and Spreading: Upon arrival at the site asphaltic mixtures shall be dumped and spread in orderly continuous operation. Care shall be taken to prevent the material from becoming mixed with earth or other foreign matter prematurely consolidated by traffic or trucks. It shall be spread by means of shovels, rakes, or approved spreading devices without segregation and such that all ingredients are uniformly distributed. No walking on the surface mixture shall be permitted during the laying operation. Spread in a loose layer or layers of such thickness that after compaction it shall produce a uniform surface having the minimum thickness specified.

C4.4 Adverse Weather:

C4.4a Freezing Weather: No materials, except with permission of the Executive Director of Facilities, shall be mixed or placed when air temperature is 50° F. or lower. No materials containing frost shall be used.

C4.4b Wet Weather: Generally, the laying of surface mixtures will not be permitted in wet weather. The Project

Superintendent may however permit work to continue when sudden rain occurs, but only up to the amount which is in transit when overtaken by sudden rain. Plant mixing shall cease when rain commences and laying of pavement shall not be resumed until all conditions are satisfactory as specified herein.

C4.4c Protection: The contractor shall provide and have readily available at all times, sufficient tarpaulins or covers for use in any emergency such as rain, chilling winds or unavoidable delay to cover and protect any material that may be dumped but not spread immediately.

C4.5 Installation:

C4.5a Construction Joints: Construction of the topping course shall be as nearly continuous as possible. When operation of laying is interrupted, the end of laid material shall be left unrolled until such time as work is resumed. If it is necessary to roll the end of the laid mixture during construction or permit traffic to pass over such temporary end, thus consolidating it, the edge made shall be cut back vertical before recommencing the operation of laying, in order to present a fresh clean surface for contact with the newly placed material. The edges of such joints shall not be painted with liquid bitumen. The use of hot smoothing irons in finishing such joints shall not be permitted.

Construction joints shall be thoroughly rolled to insure proper bond between adjoining spreads.

C4.5b All Asphalt Concrete Mixture and Pavement that are contaminated, damaged, or defective shall be removed and replaced by the Contractor. Skin patching of rolled pavement will not be permitted.

C4.5c Side Supports: At the time of laying the topping, if the temporary side supports are required at curbs, gutters or edgings, timber or other temporary supports of suitable thickness shall be placed along edge of the pavement and rigidly supported so as to prevent the mixture from being displaced by the action of the roller. These temporary supports shall remain in place until the surface course has been thoroughly rolled with overlapping roller so as to thoroughly consolidate the extreme edges.

C4.5d Surface Finish: The finished surface after compaction shall be smooth and true to grades; free from spots, cracks, waves, bunches, unevenness or other surface defects; and shall slope to drains throughout entire area and be free from sinkages and other obstructions which will hold water. Finish pavement shall be uniform in texture and density throughout. Finish surface flush with existing pavement shall be uniform in texture and density throughout. Finish surface flush with existing pavement at gates, steps, covers and other fixed grade points.

Contractor shall furnish straight edge not less than ten (10) feet long and check surface frequently during rolling operations to detect surface defects. Defects and irregularities which are detected before the completion of rolling shall be remedied by loosening the surface mix and removing or adding materials as may be required. Should any irregularities or defects remain after the final compaction the surface course shall be removed promptly and sufficient new material laid to form a true and even surface. All minor surface defects shall be ironed smooth to grade.

SECTION D – SPECIAL CONDITIONS

D 1 INTENT

D1.1 The intent of this solicitation is to provide a contract for paving services for the Newark Board of Education as specified.

D1.2 The conditions and requirements are intended to serve as average standards for the purpose of obtaining adequate participation of interested contractors, uniformity in the submission of bids, and selection of the most responsible bidder.

D 2 AWARD OF CONTRACT

D2.1 Award of contract will be made to the lowest responsive and responsible bidder.

D3 CONTRACT TERM

D3.1 This contract is for two (2) years from date of award with an option to renew for one (1) successive two

(2) year period. There will be no increase in price during the contract period. Pricing on all services shall remain as submitted unless discounted. The final contract shall represent the terms and conditions of the agreement. Renewals may be exercised by the District in its sole discretion. By submitting a bid, the awarded contractor agrees to a maximum contract term of four (4) years. January 1, 2027 through December 31, 2028 is the anticipated initial contract term.

D3.2 This contract is not funded in itself. Funding will be provided by the issuance of a purchase order. No legal liability on the part of NBOE for any payment that shall arise until the contract is funded by the issuance of a purchase order. No work, supplies, or service are authorized that exceeds the total amount specified on the purchase order(s).

The NBOE is not liable for any cost that exceeds the amount specified unless approved in writing in advance.

D3.3 The Board shall not be obligated to any minimum expenditures. The final contract will be based on the actual work assigned and performed.

D3.4 The Board reserves the right to extend the ordering period for an additional ninety (90) days with no increase in price by giving the contractor ten (10) days written notice. The contractor can preempt this right to extend by giving the Director of Support Services written notice twenty (20) days before the scheduled contract expiration date.

D4 PRICES

D4.1 Pricing shall be entered in the Pricing - Enter Bids segment of the electronic bidding platform http://www.npsourcing.com.

D4.2 All prices will be firm and not subject to increase. All prices bid are to include a margin for the contractor which is to include, but not be limited to, overhead, administrative costs and profit. Labor prices are to include travel time, mileage and tolls. No separate billing will be allowed for travel time, mileage and/or tolls.

D4.3 Any supervision provided by the Contractor will be at the expense of the Contractor unless the supervisor is an active participant in the service/repair or replacement work. At which point the Contractor is entitled to the awarded rate.

D5 QUOTATIONS AND INVOICES

Quotations

D5.1 When the need for services arise the awarded Contractor will be contacted to perform a site visit for generation of a quote. A site visit is required for generation of all quotes and shall be free of charge. All quotes shall be provided via email, and itemized to identify the following:

- The Contractor’s complete business name, address, and contact information

- Contract number 10317

- School’s name and address

- Vendor’s quotation number

- Detailed work to be performed including square footage

- Service personnel type (e.g. asphalt laborer, roller operator, etc.)

- Number of hours per service personnel type

- Hourly rate per service personnel type

- Itemized material cost and percentage markup

Invoices

D5.2 During the life of the contract, the Contractor will be paid for actual work assigned and performed. All invoices must specify:

- The Contractor’s complete business name, address, and contact information

- Contract number 10317

- School’s name and address

- Vendor’s quotation number

- Detailed work to be performed including square footage

- Service personnel type (e.g. asphalt laborer, roller operator, etc.)

- Number of hours per service personnel type

- Hourly rate per service personnel type

- Itemized material cost and percentage markup

- Purchase order number

- Service dates

- A unique invoice number (all invoices cannot have the same number)

- Invoice date

D5.3 Payments WILL NOT be approved until an authorized Facilities Management Representative inspects and approves the completed work.

D5.4 The District’s payment terms of net 30 days begin once the Contractor has provided their signed purchase order voucher and invoice to the Office of Facilities Management. The Contractor shall have sole responsibility for the complete effort specified in the contract. Payment will be made only to the Contractor. The Contractor shall have sole responsibility for any and all payments due to any subcontractor.

D5.5 The Board reserves the right to delete any item from the Contractor’s invoice that reflects items and or services not awarded under this solicitation and to amend any price that reflects a cost higher than the contracted price.

D5.6 Payments will not be issued for any equipment, materials, service and/or repairs not covered under this contract.

D5.7 Payments shall not preclude the District form making a claim adjustment on any item later found not to have been in accordance with this contract.

D6 QUALIFICATION OF BIDDERS

D6.1 Questionnaire: Contractors are required to complete the enclosed questionnaire.

D6.2 Qualifications: Bidders shall be of known reputation and shall have sufficient qualified personnel and equipment to adequately perform paving services at NBOE facilities. The Newark Board of Education reserves the right to assign representatives of the Newark Board of Education to visit locations actively serviced by the bidder.

D6.3 Bidders must have provided services similar in size and scope to this contract for a minimum of five (5) years.

D6.4 Each bidder shall be classified by the State of New Jersey Division of Property Management and Construction

(DPMC) in the following trade:

Classification Code Classification Trade Name

C059 Road Construction and Asphalt Paving Work

D7 NEW JERSEY PREVAILING WAGE ACT

D7.1 Pursuant to N.J.S.A. 34:11-56.25 et seq, contractors on projects for public work shall adhere to all requirements of the New Jersey Prevailing Wage Act. The Contractor shall be required to submit a certified payroll record to the owner within ten (10) days of the payment of wages. The Contractor is also responsible for obtaining and submitting all subcontractors’ certified payroll records within the aforementioned time period. The Contractor shall submit said certified payrolls in the form set forth in N.J.A.C. 12:60-6.1(c). It is the Contractor’s responsibility to obtain any additional copies of the certified payroll form to be submitted by contacting the New

Jersey Department of Labor and Workforce Development, Division of Workplace Standards. Additional information is available at https://www.nj.gov/labor/wagehour/wagerate/wage_rates.html .

Attached hereto and incorporated herein are the Department of Labor and Workforce Development prevailing wage determination(s) for the locality and craft(s) that will be employed in the performance of work under this contract. It is hereby stipulated that each individual who performs work under this contract shall be paid not less than the prevailing wage rate to which that worker is entitled under the

New Jersey Prevailing Wage Act, as reflected in the appropriate Department of Labor and Workforce

Development prevailing wage determination.

In the event it is found that any worker employed by the Contractor or any subcontractor covered by this contract has been paid a rate of wages less than the prevailing wage rate required to be paid by this contract, the public body, the lessee to whom the public body is leasing a property or premises or the lessor from whom the public body is leasing or will be leasing a property or premises may terminate the

Contractor's or subcontractor's right to proceed with the work, or such part of the work as to which there has been a failure to pay required wages, and to prosecute the work to completion or otherwise. The

Contractor and his sureties shall be liable to the public body, any lessee to whom the public body is leasing a property or premises, or to any lessor from whom the public body is leasing or will be leasing a property or premises for any excess costs occasioned by the termination of the Contractor's or subcontractor's right to proceed with the work, or such part of the work as to which there has been a failure to pay required wages.

Certified Payroll Requirements

D7.2 This project shall be deemed as a prevailing wage project and all necessary documentation shall be included, but not limited to weekly certified payrolls which are to be addressed to Newark Board of Education, Office of

Facilities Management, 190 Muhammad Ali Avenue, Newark, NJ 07108 for the entire length of the work under this contract.

D7.3 This project shall abide to any/all prevailing wage rates for the State of New Jersey. All requirements for latest published prevailing wage standards shall be the responsibility of the bidding firm.

D8 NEW JERSEY PUBLIC WORKS CONTRACTOR REGISTRATION ACT

D8.1 The Public Works Contractor Registration Act (PWCRA), N.J.S.A. 34:11-56.48 et seq. requires that the bidder, including named subcontractors, register with the Department of Labor and Workforce Development prior to submitting price proposals or engaging on certain public works contracts that exceed the prevailing wage threshold. The Bidder must submit a copy of its NJ Public Works Contractor Certificate prior to contract award.

D9 RESPONSE TIME

D9.1 The Contractor shall immediately begin work upon receipt of purchase order and approval from the Facilities

Director.

D10 LABOR HOURLY RATE

D10.1 The Newark Board of Education shall award contracts to the lowest responsible bidders based upon the bid hourly labor charge for standard rate for Asphalt Laborer. Please be advised to submit a bid in full compliance with the

New Jersey Department of Labor and Workforce Development regulations including Prevailing Wage requirements.

D10.2 The Newark Board of Education will not consider any bid price lower than the current New Jersey

Prevailing Wage Asphalt Laborer hourly rate for Essex County.

D10.3 In the event overtime is required, all overtime shall be compensated at the applicable rates established under the

New Jersey Prevailing Wage Act.

D11 CONTRACTOR'S PERSONNEL

D11.1 All personnel or agents of the Contractor must observe all rules and regulations in effect at each school building.

Employees or agents of Contractor, while on District property, shall be subject to control of the District, but under no circumstances shall such persons be deemed to be employees or agents of the District. Contractor's personnel must sign in and sign out with the Facilities Management representative each time they report for service. All service personnel of the Contractor shall be in uniform and/or carry identification.

D12 MINIMUM/MAXIMUM CONTRACT VALUE TOTAL FOR ALL CONTRACTS

D12.1 The District shall not be obligated to any minimum expenditures. The final contracts will be based on the actual work assigned and performed.

D13 RESPONSIBILITY FOR THE WORK

D13.1 The Contractor shall be responsible for all damage or destruction caused directly or indirectly by his operations to all parts of the work, both temporary and permanent, and to all adjoining property.

D13.2 The Contractor shall, at his own expense, protect all finished work liable to damage and keep and same protected until the project is completed and accepted. In the case of substantial completion accompanied by beneficial occupancy by the District, the Contractor’s obligation to protect his finished work shall cease simultaneously with the occupancy of the portion or portions of the structure.

D13.3 The Contractor shall defend, protect, indemnify and save harmless the Newark Board of Education from all claims, suits, actions, damages and cost of every name and description arising out, or resulting from the performance of his work under this contract. This responsibility is not limited by the provisions of other indemnification provisions included elsewhere herein.

D13.4 In order to protect the lives and health of his employees, the Contractor shall comply with all applicable statutes and pertinent provisions of the “Manual of Accident Prevention in Construction” issued by the Associated General

Contractor of America, Inc., and shall maintain an accurate record of all cases of death, occupational disease, and injury requiring medical attention or causing loss in time from work, arising out of and in the course of employment on work under the Contract. The Contractor alone shall be responsible for the safety, efficiency, and adequacy of his plant, appliances and methods, and for any damage or injury which may result from his failure or his improper construction, maintenance or operation.

D14 PERMITS - LAW - REGULATIONS

D14.1 Unless otherwise provided in the contract documents the Contractor shall secure and pay all permits and governmental fees, licenses and inspections necessary for the proper execution and completion of the work and which are legally required at the time of receipt of bids. The City of Newark’s Code Compliance review fees are waived; no other fees are waived.

D14.2 The work under this contract is exempt from local zoning ordinances, codes and regulations as related to the building and the site on which it is located, except where construction could adversely affect adjacent property, public sidewalks and/or streets. The Contractor shall coordinate his activities with municipal and/or highway authorities having appropriate jurisdiction.

D14.3 The Contractor shall be responsible for and save harmless the District from all fines, penalties or loss incurred for, or by reason of, the violation of any municipal ordinance or regulation or law of the State while the said work is in process of construction.

D14.4 The Contractor shall comply with all Federal Occupational Safety and Health Administration (OSHA) laws and regulations.

D14.5 As a result of a finding of facts by the NBOE that a Contractor caused a substantial violation of a State, local or federal statue or regulation on said project, the NBOE may declare the Contractor to be in default.

D15 STORAGE, CLEANING AND FINAL CLEAN UP

D15.1 The Contractor shall confine his apparatus, the storage of his equipment, tools and materials, and his operations and workmen to areas permitted by law, ordinances, permits, contract limit lines as established in the contract documents, or as ordered by the District, and shall not unreasonably encumber the site or the premises with his materials, tools and equipment.

D15.2 The Contractor shall at all times during the progress of the work keep the premises and the job site free from the accumulation of all refuse, rubbish, scrap materials and debris caused by his operations, to the end that at all times the premises and site shall present a neat, orderly and workmanlike appearance and shall broom sweep all areas at the end of each day’s work. This is to be accomplished as frequently as is necessary by the removal of such material, debris, etc. from the site and the District’s premises. Loading, cartage, hauling and dumping will be at the

Contractor’s expenses.

D15.3 Should the Contractor not promptly and properly discharge his obligation relating to cleaning and final clean up, the District shall have the right to employ others and to charge the cost thereof to the Contractor(s) deemed by the

Director to be responsible therefor, after first having given the Contractor three (3) working days’ written notice of such intent.

D15.4 In each instance, the clean-up work shall be performed by the Contractor responsible for the portion of the work requiring the clean-up service. In the event of dispute as to responsibility, the Director’s representative shall make the determination, which shall be binding on all Contractors.

D 16 EQUIPMENT - MATERIALS

D16.1 The Contractor shall furnish and pay for all necessary transportation, storage, forms, labor, tools, light and power and mechanical appliances and all other means, materials and supplies for properly prosecuting the work under this contract, unless expressly specified otherwise. The Contractor shall make arrangements to have representatives of his firm at the site to accept delivered materials. The District will not accept materials, nor will they be held responsible for damage, theft, or disappearance of Contractor’s materials, equipment, tools, etc.

D16.2 Manufactured products of the United States, whenever available shall be used in this work. Wherever practicable, preference shall be given at all times to material and equipment manufactured or produced in the State of New

Jersey, where such preference is reasonable and will best serve the interest of the District.

D16.3 No materials, equipment, or supplies for the work shall be purchased by the Contractor or any Subcontractor subject to any lien or encumbrance or other agreement in which an interest is retained by the Seller. The Contractor warrants, by signing his voucher for payment, that he has good and sufficient title to all such material, equipment and supplies used by him in the work, free from all liens, claims or encumbrances.

D17 PROTECTION OF PERSONS AND PROPERTY

D17.1 The Contractor shall be responsible for initiating, maintaining and supervising all safety precautions and programs in connection with the work. He shall designate a responsible member of his organization at the site whose duty shall be the prevention of accidents. This person shall be the Contractor’s superintendent unless otherwise designated by the Contractor, in writing, to the Owner and the Architect/Engineer.

D17.2 All work, materials, and equipment, whether in storage on or off site, are under the care, custody, and control of the

Contractor.

D18 SET-ASIDE PROGRAM-SPECIAL CONDITIONS

D18.1 This solicitation is a 100 percent set-aside for small, women and minority owned businesses in accordance with the provisions of N.J.S.A. 18A:18A-51 et. seq. The award of any contract resulting from this solicitation will be restricted to only those firms that are qualified and certified as a minority business enterprise, and/or women's business enterprise and/or small business enterprise, as appropriate. Such certification must be dated on or before the date of the bid opening. A copy of the certification shall be submitted with the bid.

D19 DEFINITIONS

a. "Small business enterprise" means a business which is independently owned and operated, which is qualified pursuant to N.J.S.A. 18A:18A-27 and which is a sole proprietorship, partnership or corporation which is a size and type defined by the Commissioner of the Department of Commerce, and Economic

Development;

b. “Minority business enterprise” means a business, which is independently owned and operated, which is qualified pursuant to N.J.S.A. 18A:18A-27 and which is:

(1) A sole proprietorship, owned and controlled by a minority;

(2) A partnership or joint venture owned and controlled by minorities in which at least 51% of the ownership interest is held by minorities and the management and daily business operations of which are controlled by one or more of the minorities who own it; or

(3) A Corporation or other entity whose management and daily business operations are controlled by one or more minorities, who own it, and which is at least 51% owned by one or more minorities, or if stock is issued, at least 51% of the stock is owned by one or more minorities;

c. "Women's business enterprise" means a business, which is independently owned, and operated, which is qualified pursuant to N.J.S. 18A:18A-27 and which is:

(1) A sole proprietorship owned and controlled by a woman;

(2) A partnership or joint venture owned and controlled by women in which at least 51% of the ownership is held by women and the management and daily business operations of which are controlled by one or more women who own it; or

(3) A corporation or other entity whose management and daily business operations are controlled by one or more women who own it, and which is at least 51% owned by women, or if stock is issued, at least 55% of the stock is owned by one or more women;

d. "Minority" means a person who is:

(1) Black, which is a person having origins in any of the black racial groups in Africa; or

(2) Hispanic, which is a person of Spanish or Portuguese culture, with origins in Mexico, South

America, Central America, or the Caribbean Islands, regardless of race;

(3) Asian-American, which is a person having origins in any of the original people of the Far East, Southeast Asia, the Indian Subcontinent, Hawaii, or the Pacific Islands; or

(4) American Indian or Alaskan native, which is a person having origins in any of the original peoples in North America;

D20 CERTIFICATION

Certification is a determination made by certain certifying entities that a business is, in fact eligible to compete for contracts under the set-aside program. Certifying entities include, but are not limited to, the following:

New Jersey Department of Commerce and Economic Development

New Jersey Department of Transportation

Port Authority of New York/New Jersey

U.S. Small Business Administration

D21 CLASSIFICATION ON THE BASIS OF FALSE INFORMATION

D21.1 When the District determines that a business has been classified on the basis of false information knowingly supplied by the bidder and has been awarded a contract to which it would not otherwise have been entitled, the

District may:

a. Assess the business any difference between the contract amount and what the District's cost would have been if the contract had been awarded in accordance with the provisions of this act.

b. In addition to the amount due under subsection a., assess the business a penalty in an amount of not more than 10% of the amount of the contract involved; and

c. Determine the business ineligible to transact any business with the District for a period to be determined by the District.

D22 DISTRICT’S RIGHT TO TERMINATE OR AMEND CONTRACT(S) AS A RESULT OF THE

ANTICIPATED IMPLEMENTATION OF ENERGY CONSERVATION CONTRACT(S)

D22.1 The District is currently actively proceeding with a plan for comprehensive energy management and energy related capital improvement services which may include but not be limited to energy audits, design, acquisition installation, modification and/or maintenance of existing and new equipment and controls for all heating, ventilation, and air conditioning (HVAC) and lighting systems.

D22.2 At any time during the course of the contract, or at any time during any subsequent renewal, the District reserves the right to terminate or amend the contract (s) to remove sites and/or limit the services to be performed at specific sites at our option without penalty to the Newark Board of Education.

D23 CONTRACTOR’S REGISTRATION

D23.1 Pursuant to N.J.S.A. 34:11-56.51 No contractor shall bid on any contract for public work as defined in section 2 of P.L.1963, c.150 (C.34:11-56.26), or for which payment of the prevailing wage is required by any other provision of law, unless the contractor is registered pursuant to this act.

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .