N6833525-Q-0351 Amendment 1.pdf

NAVAIR LAKEHURST

NAVAL AIR WARFARE CENTER AD, HWY 547, BLDG 12

JOINT BASE MDL NJ 08733-5082

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83) Prescribed by GSA

FAR (48 CFR) 53.243

The purpose of this amendment is to update the inspection/ acceptance location identif ied in paragraph 3.3 in the Statement of Work and remove delivery schedule from paragraph 4.4 in the Statement of Work. See section F for delivery schedule.

1. CONTRACT ID CODE PAGE OF PAGES

1 5

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY 23-Sep-2025

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street , County, State and Zip Code) X N6833525Q0351

X 9B. DATED (SEE ITEM 11)

09-Sep-2025

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer is extended, X is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

23-Sep-2025

CODE

NAVAL AIR WARFARE CENTER AD (LKE)

PROCUREMENT DIVISION, BLDG 120,

PEO(A) SE ACQUISITION SUPPORT BRANCH

JOINT BASE MDL NJ 08733

N68335 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE N68335

FACILITY CODECODE

alexis.r.kelly.civ@us.navy.milEMAIL:732-323-0000TEL:

ALEXIS R KELLY / CONTRACT SPECIALIST

N6833525Q0351

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

SECTION C - DESCRIPTIONS AND SPECIFICATIONS

The following have been modified:

STATEMENT OF WORK

Statement of Work P/N’s: 4091AS0125-1

20 March 2025

1.0 SCOPE

This Statement of Work (SOW) addresses the requirements and tasks associated with the production and delivery of P/N’S 4091AS0125-1; Wideband Satcom AAU Lifting Adapter;

QTY 12 for the P-8A Poseidon Program for the United States Navy (USN.)

2.0 APPLICABLE DOCUMENTS

a) MIL-STD-130N – Identification Marking of U.S. Military Property

b) Drawing #3909AS9999 Rev B, Identification Plate for Support Equipment/UID Markings

c) ASTM D3951-18 - Standard Practice for Commercial Packaging

d) MIL-STD-129R - Military Marking for Shipment and Storage

e) MIL-STD-1366E - Transportability Criteria

3.0 REQUIREMENTS

3.1 General

Contractor shall manufacture and deliver the below P/N’s, in accordance with (IAW) this SOW and the requirements of the contract.

CLIN PART NUMBER NOMENCLATURE NIIN QTY

001 4091AS0125-1

Wideband Satcom AAU Lifting Adapter 017059395 12

3.2 Quality Assurance

The Contractor shall have in place a production quality assurance (QA) system compliant with ISO 9001. This QA system shall be able to ensure that manufactured configuration items are built to print, functional, and reliably made IAW controlling technical drawings, specifications and standards. Each item manufactured as part of this contract shall have passed a Government final inspection prior to DD-250.

3.3 Government Inspection and Acceptance

Government Inspection and Acceptance of all production units shall be accomplished at destination by representatives of Defense Contract Management Agency (DCMA).

3.4 Item Unique Identification (IUID) Marking of US Military Property In accordance with DFARS Clause 252.211-7003 Item Identification and valuation, the Contractor is required to mark and register all end items and their components meeting the requirements called out in MIL-STD-130N. These include components for which the Governments unit acquisition cost is $5,000 or greater, or any component, subassembly or embedded part that is serially managed, mission essential or a controlled inventory item.

3.4.1 Construct and Method

Details on creating the UID and the marking method are contained in MIL-STD-130N. The UID may be either UID Construct #1 or Construct #2 with Construct #2 being the preferred method.

3.4.2 UID Location and Marking

The locations and marking methods selected should bear no impact on the performance of the part and minimal configuration change(s) to the part. The UID (including 2D Matrix) should be incorporated onto the data plate in accordance with Drawing 3909AS9999 Rev B (Identification Plate/UID Markings). If the 2D matrix can't be incorporated onto the data plate, a 2D matrix sticker can be applied onto the main data plate provided it can be done without covering any critical data. When the 2D Data Matrix is placed directly onto the data plate, the Part Number, Serial Number and CAGE human readable characters are not required. If the above cannot be accomplished, a separate data plate can be attached which contains the 2D Matrix plus the human readable characters for the Part Number, Serial Number and CAGE. This added data plate should be attached in close proximity to the main data plate.

3.4.3 Permanency and Legibility

The UID marking and identification plates, tags, or labels when used on equipment, parts, assemblies, subassemblies, units, sets, or groups shall be permanent during the normal life expectancy of the item and be capable of withstanding the environmental test and cleaning procedures specified for the item. Legibility shall be as required for ready readability as per MIL-

STD-130N.

3.4.4 UID Registration

The prime Contractor has the responsibility to furnish Item Unique Identification (IUID) data to the IUID registry. Data submission of IUID data and acquisition cost should be via Wide Area Work Flow (WAWF), IUID XML file, IUID flat file or web entry. Additional information regarding data submission as well as the actual marking can be found at http://www.acq.osd.mil/dpap/pdi/uid/index.html.

3.4.5 Records

The Contractor shall maintain an accurate, current list of UIDs for all manufactured items on this contract and supply to the Government upon request. The list shall include P/N, Serial #, CAGE, UID Location, Construct used, how it was marked, and the registration method used.

3.4.6 Request for Variance (RFV) - (CDRL A001)

When identified, the contractor shall submit to the government for approval recommendations for a Request for Variance (RFV). Any proposed design changes affecting form, fit, and/or function of the Peculiar Support Equipment ((PSE) including enhancements) that deviate from drawings provided should be identified prior to the fabrication process and will be reviewed by the cognizant Support Equipment Lead Engineer for approval/disapproval. The contractor shall submit to the Government for approval a RFV to request deviations from the contractually specified design configuration. The contractor is advised to consult MIL-HDBK-61 Configuration Management for guidance when contemplating submitting an RFV. These change requests shall be prepared and submitted to the Government IAW Contract Data Requirements List (CDRL) A001. Once approved, the RFV will be incorporated via contract modification, which authorizes and approves the RFV. No work associated with the RFV shall commence until a fully executed contract modification is received.

4.0 PACKAGING, PRESERVATION AND SHIPPING

4.1 Packaging Requirements

The contractor shall preserve and pack materiel IAW ASTM D3951-18 (excluding paragraphs 4.2-4.3) and require same by vendors and subcontractors (for materiel being shipped to the government). The use of loose fill materials, asbestos, excelsior, newspaper and shredded paper (all types) are prohibited. In addition, all Wood Packaging Materials (WPM) shall be heat treated or chemically treated in accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15:2009, "Regulation of Wood Packaging Material in International Trade."

4.2 Marking

Marking shall be in accordance with MIL-STD-129R.

Additionally, special marking labels (fragile, delicate, etc) shall be applied to all unit, intermediate and shipping containers as an integral part of the total pack. The contractor shall select the appropriate special marking label (s) as additional means to protect the items during packaging, handling, storage, transit and removal from the pack.

4.3 Transportation

Transportability issues shall be identified and addressed to ensure all shipments can be transported with unrestricted movement via over-the-road transport. Transportability problem items shall be identified in accordance with MIL-STD-1366E criteria. Requirements for shipment of DOD materiel shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode of transportation in the Defense Transportation Regulation, DTR DOD 4500.9-R, Part II, Uniform Freight.

4.4 Shipping (FOB DESTINATION)

CLIN 0001

DODAAC: SW310N

DLA DISTRIBUTION SUSQUEHANNA PA

MECHANICSBURG RECEIVING WEST

5450 CARLISLE PIKE BLDG 402

MECHANICSBURG PA 17050-0789

MARK FOR: P-8 58A, Bill Massimino (732) 323-4166

* For items shipped to Mechanicsburg, PA: The contractor must instruct their carrier to request an appointment with DLA Mechanicsburg by filling out the attached “Prelodge Request Form” and emailing it to Prelodge@dla.mil.

Please note that an appointment is not needed for deliveries going to DLA that are being shipped via UPS, FEDEX, USPS etc. Therefore, the Prelodge form does not need to be completed for those type of shipments.

Early delivery is acceptable and encouraged.

4.5 Shipping Document

Upon shipment, a copy of the shipping document shall be emailed to brooke.a.scardigno.civ@us.navy.mil and william.r.massimino.civ@us.navy.mil

(End of Summary of Changes)