RFQ - Combined Synopsis and Solicitation - N6426726Q5013.pdf

Section B - Supplies or Services & Prices or Costs

Additional Information/Notes

Item Supplies/Service Quantity Unit Unit Price Amount

DN Solutions Mynx 6500/50 II with 30 Position ATC All Box Ways, 2 Speed Gear Box, 30 HP, Spindle Oil Cooler, Coolant Thru Spindle, Fanuc OiMP - IHMI Controller

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

Tooling Kits consisting of 3 each of Sandvik items: C8-A390-455-50- 100, C8-391-01-80-100A, C8-391-05C-32030M

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

Virtual Gibbs Cam Package

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

Turbo side discharge Chip Conveyor with 48" Evacuation (1 Left, 1 Right)

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

Mistbuster 2000 Units with Stands, Hose, Hardware

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

Renishaw OMP600 Spindle Probe

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

2 Each

N6426726Q5013

Pricing Arrangement: Firm Fixed Price

0007 Renishaw Calibration Ring 2"

Pricing Arrangement: Firm Fixed Price

2 Each

0008 30 PCS Pull Studs

Pricing Arrangement: Firm Fixed Price

2 Each

0009 External Air Blow

Pricing Arrangement: Firm Fixed Price

2 Each

Auto Door with Safety Edge

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

0011 Coolant Gun

Pricing Arrangement: Firm Fixed Price

2 Each

Transformer

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

0013 Shower Coolant

Pricing Arrangement: Firm Fixed Price

2 Each

Lista Tool Cabinet

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

0015 Hippo Hopper

Pricing Arrangement: Firm Fixed Price

2 Each

0016 Renishaw Inspection Plus Software

Pricing Arrangement: Firm Fixed Price

2 Each

Rigging into Plant for both Machines

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Pricing Arrangement: Firm Fixed Price

2 Each

0018 Freight for All Above

Pricing Arrangement: Firm Fixed Price

1 Each

Section C - Description/Specifications/Statement of Work

USE OF NAVY SUPPORT CONTRACTORS FOR OFFICIAL CONTRACT FILES

(a) NAVSEA may use a file room management support contractor, hereinafter referred to as "the support contractor", to manage its file room, in which all official contract files, including the official file supporting this procurement, are retained. These official files may contain information that is considered a trade secret, proprietary, business sensitive or otherwise protected pursuant to law or regulation, hereinafter referred to as "protected information". File room management services consist of any of the following: secretarial or clerical support; data entry; document reproduction, scanning, imaging, or destruction; operation, management, or maintenance of paperbased or electronic mail rooms, file rooms, or libraries; and supervision in connection with functions listed herein.

(b) The cognizant Contracting Officer will ensure that any NAVSEA contract under which these file room management services are acquired will contain a requirement that:

(1) The support contractor not disclose any information;

(2) Individual employees are to be instructed by the support contractor regarding the sensitivity of the official contract files;

(3) The support contractor performing these services be barred from providing any other supplies and/or services, or competing to do so, to NAVSEA for the period of performance of its contract and for an additional three years thereafter unless otherwise provided by law or regulation; and,

(4) In addition to any other rights the contractor may have, it is a third party beneficiary who has the right of direct action against the support contractor, or any person to whom the support contractor has released or disclosed protected information, for the unauthorized duplication, release, or disclosure of such protected information.

(c) Execution of this contract by the contractor is considered consent to NAVSEA's permitting access to any information, irrespective of restrictive markings or the nature of the information submitted, by its file room management support contractor for the limited purpose of executing its file room support contract responsibilities.

(d) NAVSEA may, without further notice, enter into contracts with other contractors for these services. Contractors should enter into separate non-disclosure agreements with the file room contractor. Contact the Procuring Contracting Officer for contractor specifics. However, any such agreement will not be considered a prerequisite before information submitted is stored in the file room or otherwise encumber the government.

(End of text)

PERMITS AND RESPONSIBILITIES

The Contractor shall, without additional expense to the Government, be responsible for obtaining any necessary licenses and permits for complying with any applicable Federal, State, and Municipal laws, codes, and regulations for shipping and transportation including, but not limited to, any movement over public highways of overweight/over dimensional materials.

(End of text)

This requirement is Firm Fixed Price-FFP

SALES TAX EXEMPTION

The contractor is hereby advised that the United States Government and Agencies thereof are exempt from State and Local Government tax by virtue of Article 6 of the United States Constitution. No exemption certificate is required.

PURCHASE DESCRIPTION

DN Solutions Mynx 6500

1. INTRODUCTION

Naval Surface Warfare Center (NSWC) Corona requires DN Solutions Mynx Model 6500 Vertical Machining Centers.

2. BACKGROUND

Naval Surface Warfare Center (NSWC) Corona requires two (2) DN Solutions Mynx Model 6500 Vertical Machining Centers configured as specified below.

3. REQUIREMENTS

CLIN Description Qty

DN Solutions Mynx 6500/50 II with 30 Position ATC All Box Ways, 2 Speed Gear Box, 30 HP, Spindle Oil Cooler, Coolant Thru Spindle, Fanuc OiMP - IHMI Controller

Tooling Kits consisting of 3 each of Sandvik items: C8-A390-455-50-100, C8-391-01-80-100A, C8-391-05C-32030M

0003 Virtual Gibbs Cam Package 2

0004 Turbo side discharge Chip Conveyor with 48" Evacuation (1 Left, 1 Right) 2

0005 Mistbuster 2000 Units with Stands, Hose, Hardware 2

0006 Renishaw OMP600 Spindle Probe 2

0007 Renishaw Calibration Ring 2" 2

0008 30 PCS Pull Studs 2

0009 External Air Blow 2

0010 Auto Door with Safety Edge 2

0011 Coolant Gun 2

0012 Transformer 2

0013 Shower Coolant 2

0014 Lista Tool Cabinet 2

0015 Hippo Hopper 2

0016 Renishaw Inspection Plus Software 2

0017 Rigging into Plant for both Machines 2

0018 Freight for All Above 1

*Offerors shall be an Original Equipment Manufacturer (OEM), authorized dealer, authorized distributor or authorized reseller for the proposed supplies, equipment and/or services. Offerors shall provide proof of authorization verified by an authorization letter or other documents from the OEM at the time of offer submission and prior to closure of solicitation.

**The Machine(s) shall be equipped with the following: Fanuc Oi-Plus Control with tool load monitoring and adaptive federate control, a portable manual pulse generator, shall have a Meehanite cast iron bed, shall be box way type construction, shall be equipped with a geared spindle head and 25 /30 HP CAT 50 big plus 6,000 RPM spindle, be equipped with an oil jacket spindle chiller, be equipped with through spindle and external air blow, shall have 50" X 26.4" X 24.6" XYZ travels, shall have a 55.1 X 26.4 table and loading capacity of 2,866 lbs. min, be equipped with a 30 position ATC, be equipped with 30 pcs pull studs with through hole, shall have fully enclosed guarding, be equipped with a Renishaw OMP 600 spindle probe, Inspection Plus Software and 2" calibration ring, be equipped with a coolant wash down gun, be equipped with Shower coolant, be equipped with a Mistbuster 2000 120V with stand mist collector, shall have an LNS Turbo 48"discharge height right side chip conveyor on one machine and an LNS Turbo 48" discharge height left side chip conveyor on the second machine, be equipped with an oil skimmer on the coolant tank, be equipped with a Virtual Gibbs Cam Package, be equipped with a Sandvick Tooling Package, be equipped with a 72"L X 37"H X 30"D butcher block top workbench on wheels that includes (3) Lista cabinets with (3) drawers each as an assembly, be equipped with a 1-yard self-dumping chip hopper on wheels. The contractor shall provide a machine appropriate transformer for 480V incoming power. The contractor will supply 1 set of paper manuals and 1 CD Rom set for programming, operation, maintenance, and parts list of the machine. The contractor will be responsible for shipping the Machine(s) to Allegany Ballistics laboratory in Rocket Center, WV and rigging of the Machine(s) into building 376. The contractor will provide a two-year warranty on parts and labor. The contractor will provide contact service information and warranty forms.

Period of Performance: The period of performance for installation shall not exceed fourteen (14) days. Start date to be coordinated with the customer.

Security Requirements: Contractor shall adhere to current installation security policies.

Requirements DN Solutions Mynx Model 6500 Vertical Machining Center

Section D - Packaging and Marking

PACKAGING OF SUPPLIES--BASIC

Item(s) The supplies furnished hereunder shall be packaged in accordance with ASTM-D-3951-18, Standard Practice for CLINs 0001 -0017 Commercial Packing.

(End of text)

MARKING AND PACKING LIST(S) - BASIC

(a) Marking. Shipments, shipping containers and palletized unit loads shall be marked in accordance with ASTMD- 3951-18 approved 1 May 2018, Standard Practice for Commercial Packing.

(b) Packing List(s). A packing list (DD Form 250 Material Inspection and Receiving Report may be used) identifying the contents of each shipment, shipping container or palletized unit load shall be provided by the Contractor with each shipment. When a contract line item identified under a single stock number includes an assortment of related items such as kit or set components, detached parts or accessories, installation hardware or material, the packing list(s) shall identify the assorted items. Where assortment of related items is included in the shipping container, a packing list identifying the contents shall be furnished.

(c) Master Packing List. In addition to the requirements in paragraph (b) above, a master packing list shall be prepared where more than one shipment, shipping container or palletized unit load comprise the contract line item being shipped. The master packing list shall be attached to the number one container and so identified.

(d) Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number.

(End of text)

PROHIBITED PACKING MATERIALS

The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use.

(End of text)

Section E - Inspection and Acceptance

Overall Contract Inspection/Acceptance Locations

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination

Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

0012 Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: Inspection and Acceptance at Q9004H

DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Section F - Deliveries or Performance

CONTRACTOR NOTICE REGARDING LATE DELIVERY

In the event the contractor anticipates or encounters difficulty in complying with the contract delivery schedule or date, the contractor shall immediately notify, in writing, the Contracting Officer and the cognizant Contract Administration Services Office, if assigned. The notice shall give the pertinent details; however, such notice shall not constitute a waiver by the Government of any contract delivery schedule, or of any rights or remedies provided by law or under this contract.

(End of text)

Overall Contract Delivery Period

From date of lead time event to delivery 7 Month Date of Award

Contractor Destination

Line Item Delivery Schedule Quantity Address and POC Special Handling/Notes

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD

FoB Details Contractor Destination

Telephone: TBD

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

FoB Details Contractor Destination

TBD, TPOC

Email: TBD Telephone: TBD

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

FoB Details Contractor Destination

0013 CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to delivery 7 Month Date of Award

2 Each Ship To DoDAAC: Q9004H CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Delivery Schedule From date of lead time event to

1 Each Ship To DoDAAC: Q9004H FoB Details delivery 7 Month Date of Award

CountryCode: USA

NORTHROP GRUMMAN

210 STATE ROUTE 956, ROCKET

CENTER WV 26726

ROCKET CENTER, WV 26726

UNITED STATES

TBD, TPOC

Email: TBD Telephone: TBD

Contractor Destination

FAR Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

52.247-34 F.o.b. Destination. Jan 1991

Section G - Contract Administration Data

GOVERNMENT CONTRACT ADMINISTRATION POINTS-OF-CONTACT AND RESPONSIBILITIES

(a) The Government reserves the right to administratively substitute any of the points of contact listed below at any time.

(b) The contracting officer is the only person authorized to change this contract or orders issued thereunder. The Contractor shall not comply with any order, direction or request of Government personnel - that would constitute a change - unless it is issued in writing and signed by the Contracting Officer or is pursuant to specific authority otherwise included as part of this contract. If, in the opinion of the contractor, an effort outside the existing scope of this contract is requested, the contractor shall promptly comply with the Notification of Changes clause of this contract.

(c) The points of contact are as follows:

(i) The Procuring Contracting Officer (PCO) is:

Name: Kelsey Wren Naval Surface Warfare Center, Corona Division 1999 Fourth St. Norco, CA 92860 Telephone No. 951-393-5940 Email Address: kelsey.r.wren.civ@us.navy.mil

(ii) The Contract Specialist is:

Name: Colin Dwyer Naval Surface Warfare Center, Corona Division 1999 Fourth St. Norco, CA 92860 Telephone No. 951-393-4114 Email Address: colin.dwyer.civ@us.navy.mil

(d) The Technical Point of Contact (TPOC) is the contracting officer's representative for technical matters when a COR is not appointed. The TPOC is responsible for technical issues of contract administration, such as providing all items of Government Furnished Information (GFI), Government Furnished Material (GFM) and Government Furnished Equipment (GFE) if specified in the contract as well as the inspection and acceptance of all contract deliverables.

The Technical Point of Contact (TPOC) is:

Name: [ *TBD ] Address: [ *Street ] [ *City, State, Zip ] Phone: (Area Code) xxx- [xxxx] E-mail: [ * ]

(e) The Contractor's point of contact for performance under this contract is:

Company Name: [ *TBD ] Name: [ * ] Title: [ * ] Address:[ *Street ] [ *City, State, Zip ] Phone: (Area Code) xxx- [xxxx] E-mail: [ * ]

[ * ] To be completed at contract award

(End of Text)

HOURS OF OPERATION AND HOLIDAY SCHEDULE

(a) The policy of this activity is to schedule periods of reduced operations or shutdown during holiday periods. Deliveries will not be accepted on Saturdays, Sundays or Holidays except as specifically requested by NSWC Corona / Allegany Ballistics Laboratory. All goods or services attempted to be delivered on a Saturday, Sunday or Holiday without specific instructions from the Contracting Officer or his duly appointed representative will be returned to the contractor at the contractor's expense with no cost or liability to the U.S. Government.

(b) The federal Government observes public Holidays that have been established under 5 U.S.C. 6103. The actual date of observance for each of the holidays, for a specific calendar year, may be obtained from the OPM website at OPM.GOV or by using the following direct link: https://www.opm.gov/policy-data-oversight/pay-leave/federal-holidays/.

(c) Delayed Opening, Early Dismissal and Closure of Government Facilities. When a Government facility has a delayed opening, is closed or Federal employees are dismissed early (due to severe weather, security threat, security exercise, or a facility related problem) that prevents personnel from working, onsite contractor personnel regularly assigned to work at that facility shall follow the same reporting and/or departure directions given to Government personnel. The contractor shall not direct charge to the contract for such time off, but shall follow parent company policies regarding taking leave (administrative or other). Non-essential contractor personnel, who are not required to remain at or report to the facility, shall follow their parent company policy regarding whether they should go/stay home or report to another company facility. Subsequent to an early dismissal, delayed opening, or during periods of inclement weather, onsite contractors should monitor the OPM website as well as radio and television announcements before departing for work to determine if the facility is closed or operating on a delayed arrival basis.

(d) When Federal employees are excused from work due to a holiday or a special event (that is unrelated to severe weather, a security threat, or a facility related problem), on site contractors shall continue working established work hours or take leave in accordance with parent company policy.

Those contractor employees who take leave shall not direct charge the non-working hours to the contract. Contractors are responsible for predetermining and disclosing their charging practices for early dismissal, delayed openings, or closings in accordance with the FAR, applicable cost accounting standards, and the company's established policy and procedures. Contractors shall follow their disclosed charging practices during the contract period of performance, and shall not follow any verbal directions to the contrary. The Contracting Officer will make the determination of cost allowability for time lost due to facility closure in accordance with FAR, applicable Cost Accounting Standards, and the Contractor's established accounting policy and procedures.

(e) If you intend to visit the Contracts Office, it is advised that you call for an appointment at least 24 hours in advance.

(f) The hours of operation for deliveries to the warehouse are as follows: Monday - Friday 8:00 am - 4:00 pm, excluding federal holidays.

(End of text)

DFARS Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

252.232-7003 Electronic Submission of Payment Requests and Receiving Reports. Dec 2018

DFARS Clauses Incorporated by Full Text

252.232-7006 Wide Area WorkFlow Payment Instructions. (Tailored) (Jan 2023)

WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)

(a) As used in this clause- Definitions.

"Department of Defense Activity Address Code (DoDAAC)" is a six position code that uniquely identifies a unit, activity, or organization.

"Document type" means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

"Local processing office (LPO)" is the office responsible for payment certification when payment certification is done external to the entitlement system.

"Payment request" and "receiving report" are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(b) The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as Electronic invoicing.

authorized by Defense Federal Acquisition Regulation Supplement (DFARS) 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) To access WAWF, the Contractor shall- WAWF access.

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this web site.

(d) The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice WAWF training.

Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the "Web Based Training" link on the WAWF home page at https://wawf.eb.mil/

(e) Document submissions may be via web entry, Electronic Data Interchange, or File Transfer WAWF methods of document submission.

Protocol.

(f) The Contractor shall use the following information when submitting payment requests and receiving reports in WAWF payment instructions.

WAWF for this contract or task or delivery order:

(1) The Contractor shall submit payment requests using the following document type(s): Document type.

(i) For cost-type line items, including labor-hour or time-and-materials, submit a cost voucher.

(ii) For fixed price line items-

(A) That require shipment of a deliverable, submit the invoice and receiving report specified by the Contracting Officer.

Invoice and Receiving Report (Combo) / Inspection Location: Destination/Acceptance Location: Destination

(B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.

(iii) For customary progress payments based on costs incurred, submit a progress payment request.

(iv) For performance based payments, submit a performance based payment request.

(v) For commercial financing, submit a commercial financing request.

(2) ) Fast Pay requests are only permitted when Federal Acquisition Regulation (FAR) 52.213-1 is included in the contract.

[Note: The Contractor may use a WAWF "combo" document type to create some combinations of invoice and receiving report in one step.]

(3) The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF Document routing.

when creating payment requests and receiving reports in the system.

Routing Data Table*

Field Name in WAWF Data to be entered in WAWF

Pay Official DoDAAC TBD

Issue By DoDAAC N64267

Admin DoDAAC N64267

Inspect By DoDAAC Q9004H

Ship To Code Q9004H

Ship From Code ____

Mark For Code ____

Service Approver (DoDAAC) ____

Service Acceptor (DoDAAC) ____

Accept at Other DoDAAC ____

LPO DoDAAC ____

DCAA Auditor DoDAAC ____

Other DoDAAC(s) ____

(4) The Contractor shall ensure a payment request includes documentation appropriate to the type of payment request in Payment request.

accordance with the payment clause, contract financing clause, or Federal Acquisition Regulation 52.216-7, Allowable Cost and Payment, as applicable.

(5) The Contractor shall ensure a receiving report meets the requirements of DFARS Appendix F. Receiving report.

(g) WAWF point of contact.

(1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity's WAWF point of contact.

- For WAWF issues contact TBD.

- For vendor pay issues contact TBD.

- WAWF email notifications. The Contractor shall enter the email address identified below in the "Send Additional Email Notifications" field of WAWF once a document is submitted in the system. TBD.

(2) Contact the WAWF helpdesk at 866-618-5988, if assistance is needed.

(End of clause)

Section H - Special Contract Requirements

Section I - Contract Clauses

FAR Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

52.203-3 Gratuities. Apr 1984 52.203-6 Restrictions on Subcontractor Sales to the Government. Jun 2020 52.203-6 Restrictions on Subcontractor Sales to the Government. (Alternate I) Jun 2020 Alternate I Nov 2021 52.203-12 Limitation on Payments to Influence Certain Federal Transactions. Jun 2020 52.203-19 Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements. Jan 2017 52.204-13 System for Award Management-Maintenance. (Deviation 2026-O0038) Feb 2026 52.204-19 Incorporation by Reference of Representations and Certifications. Dec 2014

52.209-6 Protecting the Government's Interest When Subcontracting With Contractors Debarred, Suspended, Proposed for Debarment, or Voluntarily Excluded. (Deviation 2026-O0038)

Feb 2026

52.209-10 Prohibition on Contracting With Inverted Domestic Corporations. (Deviation 2026- O0038)

Feb 2026

52.212-4 Terms and Conditions-Commercial Products and Commercial Services. (Deviation 2026- O0038)

Feb 2026

52.219-8 Utilization of Small Business Concerns. (Deviation 2026-O0038) Feb 2026 52.222-3 Convict Labor. (Deviation 2026-O0038) Feb 2026 52.222-19 Child Labor-Cooperation with Authorities and Remedies. (Deviation 2026-O0038) Mar 2026 52.222-35 Equal Opportunity for Veterans. (Deviation 2026-O0038) Feb 2026 52.222-36 Equal Opportunity for Workers with Disabilities. (Deviation 2026-O0038) Feb 2026 52.222-37 Employment Reports on Veterans. (Deviation 2026-O0038) Feb 2026

52.222-40 Notification of Employee Rights Under the National Labor Relations Act. (Deviation 2026-O0038)

Feb 2026

52.222-50 Combating Trafficking in Persons. (Deviation 2026-O0038) Feb 2026

52.222-90 Addressing DEI Discrimination by Federal Contractors. (Deviation 2026-O0040, Revision 1)

Apr 2026

52.223-23 Sustainable Products. (Deviation 2026-O0038) Feb 2026 52.226-8 Encouraging Contractor Policies to Ban Text Messaging While Driving. May 2024 52.229-12 Tax on Certain Foreign Procurements. (Deviation 2026-O0038) Feb 2026 52.232-33 Payment by Electronic Funds Transfer-System for Award Management. Oct 2018 52.232-39 Unenforceability of Unauthorized Obligations. Jun 2013 52.232-40 Providing Accelerated Payments to Small Business Subcontractors. Mar 2023 52.233-1 Disputes. (Deviation 2026-O0038) Feb 2026 52.233-3 Protest after Award. (Deviation 2026-O0038) Feb 2026 52.233-4 Applicable Law for Breach of Contract Claim. (Deviation 2026-O0038) Feb 2026 52.240-91 Security Prohibitions and Exclusions. (Deviation 2026-O0038) Feb 2026

52.244-6 Subcontracts for Commercial Products and Commercial Services. (Deviation 2026- O0038)

Apr 2026

DFARS Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

252.203-7000 Requirements Relating to Compensation of Former DoD Officials. Sep 2011 252.203-7002 Requirement to Inform Employees of Whistleblower Rights. Dec 2022 252.204-7003 Control of Government Personnel Work Product. Apr 1992

252.204-7012 Safeguarding Covered Defense Information and Cyber Incident Reporting

(DEVIATION 2026-O0025)

May 2024 Deviation 2026-O0025 Jun 2026

252.204-7015 Notice of Authorized Disclosure of Information for Litigation Support. Jan 2023

252.204-7018 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services.

Jan 2023

252.209-7004 Subcontracting with Firms that are Owned or Controlled by the Government of a Country that is a State Sponsor of Terrorism.

May 2019

252.211-7008 Use of Government-Assigned Serial Numbers. Sep 2010 252.223-7008 Prohibition of Hexavalent Chromium. Jan 2023 252.225-7001 Buy American and Balance of Payments Program. Feb 2024 252.225-7002 Qualifying Country Sources as Subcontractors. Mar 2022 252.225-7012 Preference for Certain Domestic Commodities. Apr 2022 252.225-7013 Duty-Free Entry. Aug 2025 252.225-7048 Export-Controlled Items. Jun 2013 252.225-7056 Prohibition Regarding Business Operations with the Maduro Regime. Jan 2023

Prohibition on Certain Procurements from the Xinjiang Uyghur Autonomous

252.225-7060 Region. Jun 2023

252.226-7001 Utilization of Indian Organizations, Indian-Owned Economic Enterprises, and Native Hawaiian Small Business Concerns.

Jan 2023

252.232-7010 Levies on Contract Payments. Dec 2006 252.243-7001 Pricing of Contract Modifications. Dec 1991 252.243-7002 Requests for Equitable Adjustment. Dec 2022 252.246-7006 Warranty Tracking of Serialized Items. Mar 2016 252.246-7008 Sources of Electronic Parts. Jan 2023 252.247-7023 Transportation of Supplies by Sea. Oct 2024

FAR Clauses Incorporated by Full Text

52.252-2 Clauses Incorporated by Reference. (Tailored) (Feb 1998)

52.252-2 CLAUSES INCORPORATED BY REFERENCE (MAY 2019)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this address: https://www.

acquisition.gov/far-overhaul

(End of clause)

52.252-6 Authorized Deviations in Clauses. (Tailored) (Nov 2020)

52.252-6 AUTHORIZED DEVIATIONS IN CLAUSES (NOV 2020)

(a) The use in this solicitation or contract of any Federal Acquisition Regulation (48 CFR Chapter 1) clause with an authorized deviation is indicated by the addition of "(DEVIATION)" after the date of the clause.

(b) The use in this solicitation or contract of any Defense Federal Acquisition Regulation Supplement (48 CFR Chapter 2) clause with an authorized deviation is indicated by the addition of "(DEVIATION)" after the name of the regulation.

(End of clause)

DFARS Clauses Incorporated by Full Text

252.211-7003 Item Unique Identification and Valuation. (Jan 2023)

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(a) . As used in this clause- Definitions

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" means-

(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number.

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

"Data qualifier" means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at . https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

"DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number.

" Enterprise " means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items.

" Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Government's unit acquisition cost" means-

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459.

"Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

" Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

"Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at .https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line items:

Contract Line, Subline, or

Exhibit Line Item Number Item Description

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or

Exhibit Line Item Number Item Description

(If items are identified in the Schedule, insert "See Schedule in this table.)

(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number .____

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number .____

(v) Any item not included in (i), (ii), (iii), or (iv) for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

(3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology - International symbology specification - Data matrix; ECC200 data matrix specification.

(4) The Contractor shall ensure that- Data syntax and semantics of unique item identifiers.

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH

10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH

10.8.2 Data Identifier and Application Identifier Standard.

(C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air Transport Association Common Support Data Dictionary; and

(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology - Transfer Syntax for High Capacity Automatic Data Capture Media.

(5) . Unique item identifier

(i) The Contractor shall-

(A) Determine whether to-

Serialize within the enterprise identifier; (1)

Serialize within the part, lot, or batch number; or (2)

Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and (3)

(B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique…