N3904027Q5950 REV 1 Attachement 4 SOW -PAMAS SBSS.pdf

PDF 432 KB Posted

Download PDF, 432 KB

Attached to
Calibrate PAMAS SBSS
Solicitation number
N3904027Q5950
Issued by

About this file

This is a Statement of Work for calibration services of a PAMAS SBSS Particle Analyzing System (serial number 320-2346) located at Naval Base Point Loma, 140 Sylvester Road, Building 633, Floor 2, Room 205, San Diego, CA 92106. The contractor must be a Certified Calibration Authority (CCA) or Original Equipment Manufacturer (OEM) certified/accredited to ISO 11171 and ISO 4402 standards, with current accreditation covering the appropriate measurement parameters, ranges, and accuracies. Calibration procedures must achieve a minimum Test Accuracy Ratio (TAR) of 4:1, Test Uncertainty Ratio (TUR) of 4:1 or greater, or Probability of False Accept (PFA) not exceeding 2%, with measurement traceability to U.S. National Standards, Ratio Type Calibrations, or Consensus Standards traceable to NIST SRM 2806d.

The contractor shall perform complete calibration using particle sizes 4.0 to 70 micrometers per ISO 11171 and 1.0 to 100.0 micrometers per ISO 4402, including syringe function checking and replacement if necessary, molecular sieve replacement, and unit mechanical and vacuum checks. Deliverables include a Calibration Certificate/Report (CDRL A001) and a Condition Found Report (CDRL A002) detailing any components or repairs identified during calibration with estimated labor hours, materials, and correction time. The contractor shall provide additional training as necessary and notify the Contracting Officer of any necessary repairs. Over and above repair work requires contractor submission of a work request and Contracting Officer authorization prior to commencement. Base access requires valid CAC, DBIDS, or metro pass, with green badges issued to verified U.S. citizens with a shipyard sponsor and verified need to work at the facility.

View the file

Other files

On GovTribe

Work with this file

  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

STATEMENT OF WORK

1. SCOPE

1.1. Title: Calibrate PAMAS SBSS s/n 320-2346 per ISO 11171 Hydraulic fluid power Calibration of automatic particle counters for liquids and is traceable to SRM 2806d AND per ISO 4402 Hydraulic fluid power Calibration of automatic-count instruments for particles suspended in liquids.

1.2. Location of Work: Naval Base Point Loma, 140 Sylvester Rd., Bldg 633, Fl 2, Rm 205, San Diego, CA 92106.

1.3. Identification:

1.3.1. PAMAS SBSS Particle Analyzing System s/n 320-2346

2. REFERENCES

2.1. International Organization for Standardization (ISO) 11171: Hydraulic fluid power – Calibration of automatic particle counters for liquids

2.2. International Organization for Standardization (ISO) 4402: Hydraulic Fluid Power – Calibration of Automatic-Count Instruments for Particles Suspended in Liquids

2.3. National Institute of Standards and Technology (NIST) Standard Reference Material (SRM) 2806d

3. REQUIREMENTS

3.1. The Certified Calibration Authority (CCA) or Original Equipment Manufacturer (OEM) must be certified/accredited to work to references 2.1. and 2.2.

3.1.1. The Scope of Certification/Accreditation for the CCA or OEM must be current (up-to-date) at the time of calibration.

3.1.2. The Scope of Capability provided with the CCA or OEM certification/accreditation must cover the appropriate measurement parameters, ranges, and accuracies for the requested calibration.

3.2. Procedures used by the CCA or OEM to calibrate the equipment shall:

3.2.1. Provide a minimum Test Accuracy Ratio (TAR) of 4:1, or a Test Uncertainty Ratio (TUR) equal to or greater than 4:1, or a Probability of False Accept (PFA) not to exceed 2%.

3.2.2. Ensure measurement traceability through an unbroken chain of calibrations to accepted reference (i.e., U.S. National Standards, Ratio Type Calibrations, or Consensus Standards).

3.3. The Contractor shall provide a report/certificate of calibration for the equipment listed in section 1.3. (CDRL A001)

3.4. The Contractor shall calibrate the equipment listed in 1.3. using particle sizes 4.0 to 70µm(c) per reference 2.1. (ISO 11171).

3.5. The Contractor shall calibrate the equipment listed in 1.3. using particle sizes 1.0 to 100.0µm per reference 2.2. (ISO 4402).

3.6. The Contractor shall perform a complete calibration on the equipment listed in 1.3. that shall include:

3.6.1. Checking syringe function and replacing, if necessary

3.6.2. Molecular sieve replacement

3.6.3. Unit mechanical and vacuum checks

4. RESPONSIBILITITES

4.1. The Contractor shall provide additional training for the identified equipment in section

1.3. as necessary.

5. OVER AND ABOVE WORK

5.1. In addition to the scheduled calibration, the Contractor shall provide over and above repair services if it is identified that current issues with equipment exist that impact the equipment being maintenance to Section 3.0. In accordance with DFARS 252.217-7028, the Contractor and the Contracting Officer shall negotiate specific procedures for Government administration and Contractor performance of over and above work requests.

During the calibration of the equipment identified in Section 1.3, the Contractor is to notify the Contracting Officer of any necessary repairs that are required to maintain the operability of the equipment or to ensure the calibration of the equipment can be completed to the standards of Section 3.0.

5.2. If any components or repairs are identified during the calibration process, the Contractor shall submit a Condition Found Report (CDRL A002). The report shall contain data on the repairs required, the specific location of the repair, and the estimated labor hours, material, and time required to correct the repair. Data shall be sufficient to satisfy contract requirements and obtain the authorization of the Contracting Officer to perform the proposed work.

5.3. Upon receipt of the work request documentation required in Section 4.2, the Contracting Officer will review the work request to verify that the work is necessary and not covered under any other line items covered in the contract. The Contracting Officer will verify that the proposed corrective actions are appropriate and authorize the over and above work.

5.4. The Contractor shall not commence over and above work until authorized by the Contracting Officer.

6. DELIVERABLES

6.1. Calibration Certificate/Report (CDRL A001)

6.2. Condition Found Report (CDRL A002)

7. Security:

7.1. BASE ACCESS: All contractors attempting to access Naval Base Point Loma must ensure they have a valid CAC or DBIDS issued by NBPL or a metro pass for the local area. If neither form of identification is in hand, a Standard Form 5512 for base access must be completed and submitted PNSDETSD Code 1120 Security Department for processing/vetting via the pass office. Once submitted to the pass office, the vetting process takes 7-10 business days. You may check the status or set an appointment for pickup of your DBIDS card by calling the pass office at 619-553-0938. Ensure you have two forms of identification when picking up your DBIDS card. The pass office hours are 6:30 am - 2:45 pm on Monday, Tuesday, Thursday, and Friday; they close at 12:00 pm on Wednesday. The pass office is ALWAYS closed on holidays.

7.2. Badge Criteria:

7.2.1. Green badges will be issued to contractors who are verified U.S. citizens, have a shipyard sponsor and a verified need to provide a service or perform work at

PNSDETSD.

7.2.2. These badges provide unescorted access to the enclave, excluding Nuclear Work Area’s (NWA’s), Controlled Nuclear Information Areas (CNIA’s), Security Islands (SI’s) and Other Sensitive Areas (OSA)

7.2.3. The Standard Access Control Badge (SACB) is U.S. Government property, and it must be protected and returned to PNSDETSD Code 1120 Security Department upon termination of employment, completion of work, service performed, expiration of contract or no longer a need to enter NAVSEA controlled spaces.

7.2.4. The SACB will be displayed at the chest level area of the outer clothing with the picture side visible at all times.

7.2.5. No objects, pins or stickers can be attached to the badge. If the badge becomes faded, damaged or illegible for any reason the bearer will report to the Pass & ID office for a new badge.

7.2.6. Access TO THE ENCLAVE & BOATS: Personnel must have a valid CAC or DBIDS card for access to the enclave. IAW with the contract you must also be issued a green badge during the time of services rendered. If entering the base and enclave with a company vehicle, you must have the vehicle inspected at the Commercial Vehicle Inspection Station. Documents: a valid driver’s license, DBIDS or government CAC. All documents must be active. No expired documents will be accepted. If access to boats is required a visit request must be submitted to CS11. The Squadron office, or subordinate command, to be visited or having cognizance over the contract is responsible for ensuring that visitors or contractors are informed of the necessity of forwarding a visit request to CSS11/CSPRWC (Security Management Office (SMO) code: N424745) utilizing the DISS online submission.

File details come from the government source that posted it. Updated .