2.02a_Attachment_1_-_Technical_Specifications.pdf

GENERIC CONVEYOR BELTVEHICLE SPECIFICATIONS

CONVEYOR BELT VEHICLE SPECS and OTHER TECHNICAL DOCUMENTATION:

o 4 wheel vehicle outfitted with steel-belted radial tires o Sound Isolated engine compartment o Vehicle must be street legal ( Road Capable) - driver 's cab must possess ergonomic arrangements for all operators ‘controls.

o Driver's Cab must be enclosed for commercial street operations o Maximum travelling/driving speed of 15 mph o Vehicle must possess a ground clearance of 200mm ( 7.87 in) o Possess lighting and horns according to Dept of Transportation road regulations .

o Possess Wiper system for windscreen on the driver 's cab o Possess engine working hours counter, Fuel gauge and inner cab roof light o All operator controls must be labeled in English o All instruction, operation controls, maintenance annuals and spare parts catalogues for engine and chassis must be labeled in English o 2 seats per vehicle {1 for the driver cab, one for the Conveyor Belt operator station) o Both seats must have safety belt/Seat Belt

ELECTRICAL SYSTEM:

o 2 headlamps (side lamp + dipped-beam headlamp) o 2 turn-signal lamps front & rear of vehicle o 1 signal horn o 4 emergency switch-off buttons at the ends of the boom o 1 emergency switch-off button in the driver 's cab o 1 working floodlight for low light/evening/night operations o 1 Rotating beacon light for "conveyor belt lowering" o Reverse Buzzer o Side and rear view mirrors

HYDRAULIC SYSTEM:

o Hydraulic system for control and drive of conveyor belt. Vehicle requires a hydraulic pump that is provided at the output of the adjusting pump o Capability for the conveyor belt to be activated by electric switches in the dashboard and on the conveyor boom o Require capability to regulate the conveyor belt between speeds of 0-0,6 m/s ( 1.97 ft/sec) by a hydraulic regulator valve o Max angle of conveyor belt inclination of no more than 30 degrees o Max belt load capacity of conveyor belt should be approx 50 kg/m

( 33.S lbs/ft) o Max Single load capacity of no more than 150kg ( 330 lbs) o Vehicle must have capability for a manual pump for emergency operation of the conveyor belt when no power is available o Capability and functions for controlling the height adjustment of the belt can be actuated from driver 's position o Capability and selection of the belt direction and speed selection of the belt that can be performed at the left or right rear end of the conveyor

GENERIC CONVEYOR BELT VEHICLE SPECIFICATIONS

c Capability and selection of additional belt movement controls at front end of the conveyor boom (removable control box with flexible cable).

CONVEYOR BELT :

o Centre distance:

o Belt width:

o Belt type:

surface), type EP

12,000 mm ( 39 .37 ft) 600 mm ( 23.6 inches) Triple layer belt with a ruff top surface 200/2 or equivalent specifications

(anti-slip o Conveyor Belt framework made of bent steel plates (or comparable high quality material) o Tensioning of the belt must be able to be performed by a spindle-tensioning station at belt end o Conveyor belt that is driven by a hydraulic motor which is directly connected to the driving pulley at the rear end of the conveyor o Conveyor Belt rollers should be galvanized except for the driving pulley which should be rubberized o Outfitted with two tires that are fitted at the front end of the belt to protect against accidental damage o Rear end of the conveyor belt should be outfitted with maintenance-free bearings o Conveyor Belt should be outfitted with a sturdy telescopic cylinder that is responsible for elevation of one end of the Conveyor Belt to the target load zone a minimum of 50ft.

o Capability of an adjustable rear height of the conveyor belt to a max height of 1540 mm ( 5.04 ft) o Conveyor Belt must be capable of travelling in both directions ( onload and offload)

LOADING TABLE:

o Capability for an installed loading table fixed to the front end of the conveyor boom of approx . 1600 mm ( 5.2 ft) with rollers. The angle of this loading table can be adjusted by a hydraulic cylinder . This is used to stabilize the vehicle during loading operation. Support cylinders will also be required and fitted on the front end of the chassis to stabilize the vehicle during loading operations.

REMOVABLE EXENSION:

o Capability for a removable extension that will fit manually onto the above mentioned loading table/conveyor. Approx . length should be 1600 mm ( 5.2

ft) with rollers & frame made of aluminum with an adjustable leg to rest on the ship or vessel that material is being loaded/unloaded to/from o Extension is required to comes with a support for the removable control box, so that the belt movement control is always at the front end o Capability for a rack will be required to be fitted on the vehicle to store this extension while driving I not in use.

GENERIC CONVEYOR BELT VEHICLE SPECIFICATIONS

GUARD RAIL:

o Capability of an installed guard rail at conveyor belt (conveyor boom and extension) on left and right hand side. Capability for tilt ability on both sides to a height of approx 130 mm ( S.1 inches o Capability of an adjustable rear height of the belt to max . 1540 mm ( 5.05 ft).

o Capability of elevating the conveyor belt at the rear through an additional kinematics with functionality of an single/dual/multiple acting hydraulic cylinder representing also guiding control at the rear of the vehicle.

EXTERIOR PAINT:

o No preference - standard industry coloring of the exterior that identifies a Conveyor Belt vehicle as a piece of MHE equipment o Paint should be lead free

GENERIC CONVEYOR BELTVEHICLE SPECIFICATIONS