N0040622R0040 Attachment 1 SOW.pdf

ATTACHMENT 1: STATEMENT OF WORK (SOW)

Abbreviations:

OC: On Center ID: Inner Dimension OD: Outer Dimension ISWP: Integrated Solid Waste Program NBK: Naval Base Kitsap NSE: Naval Station Everett NASWI: Naval Air Station Whidbey Island TWIC: Transportation Worker Identification Credential BAVR: Badge Authorization Visit Request

CLIN 0001:

1. 40 cubic yard rectanglar structual roll off container that is a made for a Stellar hooklift.

2. Container is considered a standard build for solid waste container manufacturers.

3. This specification is for Naval Base Kitsap Bangor Integrated Solid Waste Program (ISWP).

a. Customer will offload containers from hauler’s trailer at delivery location.

b. Hauler does not need to apply for an access card to Naval Base Kitsap Bangor. NBK

ISWP will escort hauler from NBK Bangor truck inspection gate. It is recommend, but not required, the vendor use a hauling company with drivers that hold a Transportation Worker Identification Credential (TWIC).

i. Vendor is required to coordinate delivery date with NBK ISWP by contacting them at least a week in advance of delivery.

4. All pictures are representative only and used to help discribe requirement. Company’s final product may vary but must meet the requirements of the specification. All drawings are not to scale.

5. Requirements:

a. Stellar Hook-lift requirements.

i. Made to fit and work on a Stellar Slider65 system

ii. https://www.stellarindustries.com/download/StellarHookliftSpecBook.pdf

iii. Pages 81 through 100 of the Stellar Industries Spec Book provide information for the frame requirements of a roll off container to work on the Stellar Slider65 system.

iv. It is recommended that contractor also contact Stellar Industries to ensure the hook and rail system will be built in accordance with Stellar Industries specification to work on their hook lift systems.

b. Single rear door with heavy duty hinges and basic stick-on rubber gasket to make container leak resident. Waterproof is not required for this container.

i. Passenger Side hinged.

c. Reversible lid with crank winch and pulley system to lift lid.

i. Made with lightweight steel frame and tin sheeting.

ii. Four lid hinges, round tubing, two on each side, one forward and one aft.

https://www.stellarindustries.com/download/StellarHookliftSpecBook.pdf

1. Lid hinge pin to be beveled on one side with a chain welded to other side of pin. See Picture 1.

2. Four each Pin holder, tube, welded to each corner of the container to stow pin when not in use. See Picture 2.

iii. Cable Mount for cable that is used to lift the lid using the winch will be solid or braced as to not bend under pressure from the winch. Cable pulley will be able to swivel so the cable does not have to be removed from the cable pulley. Equal to or equivalent to picture 3. See picture 3.

iv. Winch recommended or equivalent – Dutton Lainson B2500 Brake Winch.

d. Primer/Paint of container

i. Interior and exterior rust inhibitor primer – 2 coats

ii. Exterior Rust inhibitor paint – 2 coats – color = safety orange

iii. Will have all State and Federal Regulated reflective markings.

iv. All containers - Paint will be dry before shipping.

v. All containers will be loaded on trailer in such a way to avoid damage during transportation.

Clin 0002:

1. 8 cubic yard humpback/slant packer truck (front loader) container.

2. Container is considered a standard build by solid waste container manufacturers.

3. This purchase is for Naval Base Kitsap Bangor Integrated Solid Waste Program (ISWP)

a. Customer will offload containers from hauler’s trailer at delivery location.

b. Hauler does not need to apply for an access card to Naval Base Kitsap Bangor. NBK

ISWP will escort hauler from NBK Bangor truck inspection gate. It is recommend that the vendor use a hauling company with drivers that hold a TWIC.

i. Vendor is required to coordinate delivery date with NBK ISWP by contacting them at least a week in advance of delivery.

4. Requirements:

a. Standard packer dumpsters.

b. Two Single Wall plastic lids.

c. Front container height not to exceed 50.5”.

d. Primer/Paint of container

i. Interior and exterior Rust inhibitor Primer - 1 coat

ii. Interior coated with automotive underseal

iii. Exterior Rust inhibitor Paint – 2 coats – color = safety orange

iv. Will have all State and Federal Regulated reflective markings.

v. All containers will have dry paint before shipping.

vi. All containers will be loaded on trailer in such a way to avoid damage during

CLIN 0003:

1. 4’x4’x3’ “Boeing Box” Recycle material collection container.

2. Container is considered a basic material recovery facility collection container to store recyclable material with the ability to stack the containers or nest them.

3. This Specification is for Naval Base Kitsap Bangor (NBK), Naval Air Station Whidbey Island

(NASWI), and Naval Station Everett (NSE).

a. Customer will offload containers from hauler’s trailer at delivery locations.

b. Hauler does not need to apply for an access card at NBK and NASWI. NBK and NASWI

ISW will escort hauler from NBK Bangor/NASWI truck inspection gate. It is recommended that the vendor use a hauling company with driver that holds a TWIC.

Delivery to NSE ISW will be required to apply for a Badge Authorization Visit Request (BAVR) base access card.

i. Vendor is required to coordinate delivery date with each location independantly.

1. NBK 360-396-7005 at least a week in advance of delivery.

2. NASWI 360-257-5481 at least a week in advance of delivery.

3. NSE 425-304-3071 at least a week in advance of delivery.

c. These containers can be loaded in the bigger containers of CLINs 0001 and 0004.

Vendor will ensure containers are loaded in such a manner as to not cause damage to this container or the container it is loaded into during transportation.

4. Requirements:

a. Container must be able to stack/nestle in each other (DRAWINGS ARE NOT TO

SCALE)

i. Legs on one box fit in the top of another box. (Also see picture above example photos of what is currently in stock).

ii. Below drawing is to provide visualization of stacking the container.

Example Photos of existing containers as reference.

b. Size of the container: (DRAWINGS ARE NOT TO SCALE)

i. I.D. = 4’ wide x 4’deep x 3’ high

c. Floor and Sidewalls made from 12-gauge steel and made structurally sound.

4 feet

3 feet

4 feet

3 feet

Front View – example drawing – not to scale

Side View – example drawing

– not to scale

d. Fork pockets on the inside floor of the container (indicated by the blue shaded areas of the below drawings)

i. Fork pocket size = 4 inch tall x 8 inch wide, 3/16” tubing or formed steel.

ii. Fork pockets centered 20” from middle of the container.

iii. Fork pockets = 4’ 2 ½” length

iv. Fork pockets will sit on the lip of the container it is nestled in

v. Fork pockets to extend past the side wall by 1.5 inches on each side

vi. See R1 and R6 as a reference photo’s of the fork pockets.

4 feet

3 feet

4 feet

3 feet

Front View showing fork pockets – example drawing – not to scale

Side View showing fork pocket– example drawing – not to scale

20” OC

e. Legs

i. 1” x 4” tubing or formed steel.

ii. Length = 45“

iii. Legs welded to bottom measuring ¼ inches from the outer edge of the side.

iv. Legs are for stacking box on top of each other. Each box will be tested by manufacturing company to ensure that they stack so the legs fit inside the container it is being stacked on.

v.

vi. Drawing:

f. Primer and Paint

i. Rust inhibiting primer – two coats – color to meet paint color requirements – interior and exterior

ii. Rust inhibiting paint – two coats – color = Recycle Blue – exterior and interior.

iii. All containers will have dry paint before shipping.

iv. All containers will be loaded on trailer for shipment to avoid damage during

1.5” spacing

¼“ spacing

1.5“ spacing

¼“ spacing

1.5“ spacing 1.5“ spacing

45”

Bottom View – example drawing – not to scale

CLIN 0004:

1. Multi-sort recycle collection roll-off container.

2. Container has been manufactured by a solid waste container manufacturing company previously.

3. This specification is for Naval Air Station Whidbey Island (NASWI) Integrated Solid Waste

Program (ISWP).

a. Customer will offload containers from hauler’s trailer at delivery location.

b. Hauler does not need to apply for an access card. NASWI ISWP will escort hauler from

NASWI truck inspection gate. It is recommend that the vendor use a hauling company with TWIC drivers.

c. Vendor is required to coordinate delivery date with NASWI ISWP by contacting them at least a week in advance of delivery.

4. Requirements:

a. All drawings are not to scale. All pictures with dimensions are not to scale. Both are for reference.

b. Roll off containers will be built as a dual pick roll off container.

i. Stellar Hook-lift requirements

1. Made to fit and work on a Stellar Slider26 system.

2. https://www.stellarindustries.com/download/StellarHookliftSpecBook.pd f

3. Reference the Stellar Industries Spec Book from the link for reference information for the frame requirements of a roll off container to work on the Stellar Slider26 system.

4. It is recommended that contractor also contacts Stellar Industries to ensure the hook and rail system will be built in accordance with Stellar Industries specification to work on their hook lift systems.

ii. Endless Chain connection on the roll off container.

c. 25.75 cubic yard, 16 foot long x 92 inches wide – Five bay recycling roll off container.

i. Bay width, front to back, equals 64 inch.

ii. Bay #1, #2, #3, #4 depth, side of roll off to center divider = 46 inches

iii. Bay #5 depth, side to side of roll off = 92”

iv. For reference see picture #P1, #P2 and #D1

v. Roll off will be made with 12 gauge material.

d. Interior bay dividing walls.

i. 1 center wall dividing bays #1, #2, #3 and #4. (Wall highlight in Red for reference, #D1)

ii. 2 divider walls running from side to side dividing bays #1, #2, #3 and #4. (Walls highlighted in Orange for reference, #D1)

iii. 1 divider wall running from side to side dividing bays #3, #4 and #5. (Wall highlighted in Orange for reference, #D1)

iv. For reference see picture #D1

e. Three access doors on each side of the roll off for a total of 6 side doors.

i. Bay doors will be equal in size.

ii. Quick release latches will be installed on the doors to keep the doors closed.

1. See picture #P2 for reference/example to the quick release latches. The contractor does not have to make latches exact match.

iii. For reference see picture #P2 and #P3

f. Rear door of the roll off will be for dumping the 5th bay and will be a barn door style door.

i. T-handle latch/closing system to secure the doors closed. (See picture #P8 for reference)

ii. Chains on each door to secure when fully open.

iii. For reference see picture #P4, #P5 and #P8

g. The roll off will hold 4 square metal collection containers – not part of this specification.

FR

O

N T

O F

RO

LL

O

FF

BAY #1 – HOLDS A

MATERIAL-HANDLING

CONTAINER. HAS

GUIDE RAILS FOR THE

CONTAINER.

BAY #3 – HOLDS A

MATERIAL HANDLING

CONTAINER. HAS

GUIDE RAILS FOR THE

CONTAINER.

BAY #2 – HOLDS A

MATERIAL HANDLING

CONTAINER. HAS

GUIDE RAILS FOR THE

CONTAINER.

BAY #4 – HOLDS A

MATERIAL HANDLING

CONTAINER. HAS

GUIDE RAILS FOR THE

CONTAINER.

BAY #5 – NO DIVIDER

FOR THIS BAY. DUAL

PURPOSE SECTION FOR

OCC COLLECTION OR

COLLECTION

CONTAINER.

#D1

i. For reference see pictures #P6 and #P7.

ii. Bay #1, #2, #3 and #4 will have angle iron guide rails for the metal collection containers.

iii. Inner Dimension (I.D.) width between the angle iron guide rails will be 4 feet

I.D.

iv. Angle iron guide rails will be welded to the floor of the roll off and positioned to center the metal collection container in the bays #3 and #4. Bays #1 and #2 will be shifted to the rear of the bay to account for the dog house for the chain lift hook up.

v. Angle iron guide rails will be 42 inches in length from the center bay divider to the access door. The last 2 inches of the angle iron guide rail will be at a 25 degree angle away from the center of the bay to help guide the metal collection container in-between the angle iron guide rails.

vi. For reference see pictures #P9 (Currently owned containers in picture #P9 do not have the angled guide. This is a new requirement).

h. 1 push open door, gravity close, will be installed in bay doors #1, #2, #3 and #4 for a total for 4 doors at the measurements stated above in section 4.d.i.

i. Push open doors will be 20 inches tall x 26 inches wide.

ii. Push doors will be centered on the access door of the bay and will be 54 inches from the ground to the bottom of the push door. Measurement is after the height of the front legs of the roll off container. See drawing D2 for visual example.

iii. Push doors to be hinged to push open smoothly and to easily shut using gravity.

#D2

54”

i. 1 push open door, gravity close, will be installed in each door of bay #5 for a total of 2 doors at the measurement stated above in section 4.e.i.

i. Push open doors will be 20 inches tall x 41” wide.

ii. Push doors will be centered on the access door of the bay and will be 54 inches from the ground to the bottom of the push door. Measurement is after the height of the front legs of the roll off container. See drawing #D2 above for visual example.

iii. Push doors to be hinged to push open smoothly and to easily shut using gravity.

j. For all push doors reference pictures P#3, P#4 and P#6 shown above in sections 4.f.iii and 4.g.i. Each push door is slanted in. Requirement is to help direct material to go into the interior collection container. Recommend bidding vendor to ask for additional pictures if needed.

k. Solid Weld on roof.

i. Roof will cover the roll off bays and extend out over the sides by 2.5 inches on each side.

ii. Roof to have a 2 inch peak.

l. Primer/Paint of container

a. Interior and exterior rust inhibitor primer – 2 coats

b. Exterior Rust inhibitor paint – 2 coats – color = Navy Blue

c. Meet all State and Federal Regulation regarding proper reflective markings.

d. All containers will be dry before shipping.

e. All containers will be loaded on trailer for shipment to avoid damage during transportation.

f. White block vinyl letter, weather and heat resistant, on each side of the container:

i. Wording - “NASWI ISWM 360-257-5481” (see drawing #D3 below for example. Example not to scale and is only an example of the lettering for the container)

ii. Wording to be space equally across both sides of the container to be read from left to right when look at the wording.

iii. The white lines on the drawing are only in the drawing to provide definition to the drawing and will not be part of the final paint job.

#D3

NASWI ISWm 360-257-5481

CLIN 0005:

1. 15-yard OCC roll off NASWI container.

2. Container is considered a standard 15-yard roll off container with a solid roof and 4 slots cut into the side of the container to receive cardboard recycling.

3. This specification is for Naval Air Station Whidbey Island (NASWI) Integrated Solid Waste Program (ISWP).

a. Customer will offload containers from hauler’s trailer at delivery location.

b. Hauler does not need to apply for an access card. NASWI ISWP will escort hauler from

NASWI truck inspection gate. It is recommend that the vendor use a hauling company with TWIC drivers.

c. Vendor is required to coordinate delivery date with NASWI ISWP by contacting them at least a week in advance of delivery.

a. All drawings are not to scale. All pictures with dimensions are not to scale. Both are for reference.

b. Roll off containers for this specification will be built for a Stellar Hook-lift.

i. Made to fit and work on a Stellar Slider26 system.

ii. https://www.stellarindustries.com/download/StellarHookliftSpecBook.pdf

iii. Reference the Stellar Industries Spec Book from link to reference information for the frame requirements of a roll off container to work on the Stellar Slider26 system.

iv. It is recommended that contractor also contacts Stellar Industries to ensure the hook and rail system will be built in accordance with Stellar Industries specification to work on their hook lift systems.

c. Solid welded on roof.

i. Peak roof.

d. Dimensions of the roll off container.

i. Standard 15 yard roll off dimension.

ii. Single swing rear door.

1. Hinged on passenger side.

2. Heavy Duty Hinges.

e. OCC slot openings

i. 4 total – two on each side.

ii. Spaced equal distance on each side of the roll off.

iii. Opening for each slot is 48 inches wide by 8 inches high.

iv. Bottom of the slot will be 40 inches up from the floor of the roll-off.

v. See drawing D#4 for reference.

f. Primer/Paint of container

ii. Exterior Rust inhibitor paint – 2 coats – color = Navy Blue

iii. Meet all State and Federal Regulation regarding proper reflective markings.

iv. All containers will be dry before shipping.

1. All containers will be loaded on trailer for shipment to avoid damage during

2. White block vinyl letter, weather and heat resistant, on each side of the container:

• Wording - “NASWI ISWM 360-257-5481” (see drawing #D4 below for example. Example not to scale and is only an example of the lettering for the container)

• Wording to be spaced equally across both sides of the container to be read from left to right when look at the wording.

• The white lines on the drawing are only in the drawing to provide definition to the drawing and will not be part of the final paint job.

CLIN 0006:

1. Three recycle sort roll off container.

2. Container is considered a basic container build for container manufacturing companies.

3. This specification is for Naval Base Everett (NSE) Integrated Solid Waste Program (ISWP).

a. Customer will offload containers from hauler’s trailer at delivery location.

b. Hauler will be required to apply for a BAVR base access card. Access request instructions is at the bottom of this specification. This is a no cost access card. NSE ISWP will escort hauler from NSE truck inspection gate.

c. Vendor is required to coordinate delivery date with NSE ISWP by contacting them at least a week in advance of delivery.

a. Hook-lift requirements.

i. Two hook lift manufactured hook lift trucks are used to handle these containers.

ii. Swaploader SL-212 and Palfinger Model HAD-185-36/54.

iii. Sub-frame – The manufacturing company will reference documents P16 and P16A to build the subframe of this specification to work on both the Swaploader SL-212 unit and a Palfinger Model HAD-185-36/54.

iv.

b. Lid

i. Double walled plastic lid to fit over opening.

ii. Lock bar for each lid.

c. Front solid legs and rear rollers.

#D4

NASWI ISWm 360-257-5481

d. Dimensions of the roll off container.

i. Basic container dimension will be:

1. 90 inches wide plus 1 inch for door.

2. 168 inches long excluding A-Frame.

ii. Additional dimensions and visual reference

1. See Pictures P#9 through P#16A shown below in section 4.e.v.

2. All pictures are not to scale.

3. Pictures are for reference only except for P16 and P16A which are from the manufactures of the hooklift companies and the contractor building the this 3 pack recycle collection container will use those specifications so the containers will work on both models of hooklifts that will haul this container.

4. Pictures show pick points. THESE CONTAINERS DO NOT REQUIRE

PICK POINTS.

e. Primer/Paint of container

ii. Exterior Rust inhibitor paint – 2 coats – color = Navy Blue

iii. Meet all State and Federal Regulation regarding proper reflective markings.

iv. All containers will be dry before shipping.

v. All containers will be loaded on trailer for shipment to avoid damage during

BAVR Base Access Card Request Instructions:

Request a Pacific DBIDS via Badge Authorization Visit Request (BAVR) system. Begin by accessing BAVR at: https://www.bavr.cnic.navy.mil Completion Instructions:

Complete the form in the BAVR system ensuring all the blocks in Red are filled in. The following items in “RED” are the required items. Some blocks are filled in with what you should use in those fields.

Last Name:

First Name:

Height (in inches):

Weight:

Gender:

Hair Color:

Eye Color:

Date of Birth:

SSN:

Place of Birth:

Citizenship:

Email:

Alien Registration Number:

Driver's License Information:

Driver's License # or N/A:

State Issued:

Home Information:

Home Address:

City:

Country:

State:

Home Phone:

ZIP:

Work Information:

Personnel Type: Commercial Driver Command You Are Visiting: Naval Air Station Whidbey Island (NASWI) Bldg. 3485, Naval Base Everett (NSE) Bldg. 2555 Company Name or Command: (insert your company name) Work Phone:

Sponsor Information: steven.e.chavez3.civ@us.navy.mil; phillip.a.saurer.civ@us.navy.mil Request information:

Purpose of Visit: Commercial Driver will be dropping off solid waste containers at the ISWM for (company name) as requested by ISWM programs located at NASWI Bldg. 3485, NSE Bldg. 2331. These containers are being delivered per DLA contract (insert contract #).

Start Date (mm/dd/yyyy) (Use the first day of planned delivery)

End Date (mm/dd/yyyy) (Make the end date for the last day of planned delivery)

ISWM representatives will be able to assist with the form as needed.