Drw_7516334_Distro_A_81804452.PDF

UNIT LOAD FOR UNDERWAY REPLENISHMENT

57MM CARTRIDGE

IN SHIPPING AND STORAGE CONTAINER

MK806 MOD 0

UNIT LOAD DATA

NUMBER OF ROUNDS PER CONTAINER

GROSS WEIGHT OF ONE CONTAINER (WITH H-GUIDES) . 39.7 LB

NUMBER OF CONTAINERS/UNIT LOAD • • . • • • . • • • 30

WEIGHT OF STEEL STRAPPING . . . . . . . . . . . . . . 8 LB

WEIGHT OF STEEL PALLET ................ 74 LB

WEIGHT OF WOOD DUNNAGE • . . . • . . . • . . . • . . 99 LB

GROSS WEIGHT OF UNIT LOAD . . . . . . . . . . . . . 1372 LB (MAX)

CUBE OF UNIT LOADS . . . . . . . . . . . . . . . . 39.08 CU FT

H-GUIDE, ITEM 11

DRAWING II 53711 -8215629

57MM SHIPPING AND STORAGE

CONTAINER MK 806 MOD 0

DRAWING II 53711-8215628

NOTES:

1. GROSS WEIGHTS ARE ESTIMATED, DO NOT USE FOR SHIPPING WEIGHT.

2. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES.

3. SEE SW020-AC-SAF-010 FOR THE FOLLOWING INFORMATION:

A. CROSS REFERENCE TO ASSOCIATED TRUCK LOADING, CONTAINER LOADING AND CAR LOADING MILITARY

STANDARDS.

B. HAZARD CLASSIFICATION.

4. DO NOT STACK MORE THAN 2 UNIT LOADS HIGH IN STORAGE.

5. FOR UNIT LOAD QUALIFICATION, SEE PHST TEST REPORT 04035 (JUNE 2004).

C SEE NSWC IHEODTD ECP 116004R1 04-25-2016 S/ J. BLAIR S/ R. SMITH

8 SEE NSWC IHEODTD ECP 114002 08-25-2014 S/ J. BLAIR S/ R. SMITH ALL SHEETS MAINTAINED AT

A SEE NSWC DAHLGREN DIVISION ECP 295ECP1108 01-05-2012 s/ M. BOYER s/ R. SMITH THE SAME REVISION LEVEL.

REV.

TECH DATA MANAGEMENT

SUPERVISOR

REVISION DESCRIPTION

S/ J. MAJKA 2004-07-01

DATE TOA SYSCOM

DISTRIBUTION STATEMENT A

APPROVED FOR PUBLIC RELEASE: DISTRIBUTION IS UNLIMITED

SYSTEMS ENG. SUPERVISOR S/ LEVENDUSKY 2004-07-15 REQUIREMENTS FOR CONSTRUCTION OF THIS LOAD SHALL CONSIST OF

S/ ROY A. SMITH 2004-07-16

NAVSEASYSCDM < BY DIRECTION >

DEPARTMENT OF THE NAVY

NAVAL SEA SYSTEMS COMMAND

ARLINGTON, VA., 22242-5160

CAGE CODE

53711

SIZE A

THIS DOCUMENT &: THE LATEST ISSUE OF MIL-STD-1323 (OS).

THIS LOAD IS AUTHORIZED &: RELEASED FOR SHIPPING &: STORAGE,

TRANSFER-AT-SEA &: FOR SHIPMENT BY COMMON CARRIER.

D\./G ND. 7516334 REV. C

PAGE OF 4

MATERIAL NOTES

1. PLYWOOD SHALL CONFORM TO CID A-A-55057, lYPE A OR B.

2. WOOD PACKAGING MATERIALS (WPM) SHALL MEET AND BE MARKED IAW ISPM 15 REQUIREMENTS USING ASTM D6253 FOR GUIDANCE. DOD ACTIVITIES SHOULD ALSO FOLLOW THE DOD WPM POLICY OF DOD 4140.65.

3. STRAPPING SHALL CONFORM TO ASTM D3953, FLAT lYPE 1, HEAVY DUlY, FINISH B, GRADE 2.

4. SEALS SHALL CONFORM TO ASTM D3953, CLASS H, FINISH B, GRADE 2, SlYLE I, II, OR IV.

5. STAPLES SHALL CONFORM TO ASTM F1 667 DESIGNATION "F1 667 - ST FC s- xxx B" WHERE ·xxx·

REPRESENTS THE DASH NUMBER.

6. NAILS SHALL CONFORM TO ASTM F1667, DESIGNATION F1667 NL CM s-xx B, WHERE ·xx· DESIGNATES THE SIZE (I.E., 4d, 6d, ETC.).

7. ROOFING NAILS, IN ACCORDANCE WITH ASTM F1667 NL RF R-05 B, MAY BE USED AS AN ALTERNATIVE TO STAPLES, ITEM 10, FOR SECURING STEEL STRAPS TO BATTENS. NAILS SHALL BE APPLIED NEXT TO THE STRAPPING (NOT THROUGH IT) SUCH THAT THE NAIL HEADS OVERLAP THE STRAPPING. USE TWO NAILS, ONE ON EACH SIDE OF THE STRAP, TO REPLACE

ONE STAPLE.

NAVSEA

DWG NO.

NOTE: DIMENSIONS AND QUANTITIES ARE FOR A FULL UNIT LOAD OF 30 CONTAINERS.

12 36 NAILS SEE MATERIAL NOTE 5 6d

11 50 H-GUIDES 53711-8215629

10 20 STAPLE, STEEL SEE MATERIAL NOTE 6 DASH # 189 OR 190

9 5 STRAP SEAL SEE MATERIAL NOTE 4 FOR 3/4" SIZE

8 3 STRAP, LATERAL SEE MATERIAL 3/4 X .031 {OR .035) X 13 FT

7 2 STRAP, LONGITUDINAL NOTE 3 3/4 X .031 {OR .035) X 16 FT

6 4 BATTEN, END 2 x 6 x 34

5 6 BATTEN, SIDE SEE MATERIAL 1 x 6 x 36

NOTE 2

4 6 BATTEN, SIDE 2 x 6 x 36

3 PLYWOOD, UPPER SEE MATERIAL 1/2 x 35 x 41 2 PLYWOOD, BASE NOTE 1 1/2 x 35 x 45-1/2

PALLET MK 12 MOD 1 10001-2645217 35 x 45-1/2 x 4-3/4

ITEM REQ'D DESCRIPTION MAT'L/DWG DIMENSIONS

LIST OF MATERIALS

7516334 I REV. c I SIZE A I CAGE CODE I PAGE 53711

PALLETIZING PROCEDURE

1. ATTACH lWO (2) H-GUIDES, ITEM 11, TO THE TOP OF THE MK 806 MOD 0 CONTAINERS, DRAWING 53711-8215628, AS SHOWN ON PAGE 1.

H-GUIDES SHALL NOT BE ATTACHED TO THE TOP SIDE OF THE OF THE UPPERMOST LAYER OF CONTAINERS.

2. THREAD LONGITUDINAL STRAPPING, ITEM 7, BETWEEN 6TH AND 7TH DECK WIRES OF PALLET, ITEM 1, AS SHOWN IN DETAIL A, PAGE 4.

3. PLACE PLYWOOD, ITEM 2, ON DECK OF PALLET.

4. STACK 30 CONTAINERS ON PALLET WITH EQUAL UNDERHANG ON BOTH SIDES AND ENDS.

5. POSmON SIDE AND END BATTENS, ITEMS 4, 5, & 6, IN PLACE, LOCATED AS SHOWN.

6. PLACE PLYWOOD, ITEM 3, ON TOP ON CONTAINERS.

7. POSITION LATERAL STRAPS, ITEM 8, AROUND UNIT LOAD AS SHOWN. TENSION AND SEAL EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 9.

8. TENSION AND SEAL LONGITUDINAL STRAPS, ITEM 7, WITH ONE DOUBLE NOTCHED SEAL, ITEM 9, PER STRAP.

9. SECURE STRAPS IN PLACE WITH STAPLES, ITEM 10, LOCATED AS SHOWN.

MARKING:

IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY (35 00)

CONTRACT OR ORDER, THE UNIT LOAD SHALL BE '

MARKED IN ACCORDANCE WITH US ARMY DRAWING /

28620-ACV00561. ~ /

NAIL ITEM 5 TO ITEM 4

WITH 6-6d NAILS EQUALLY

SPACED IN A STAGGERED

PATTERN.

I WARNING I

WEAR LEATHER GLOVES AND EYE

PROTECTION (WITH SIDE SHIELDS) OR

GOGGLES TO PREVENT INJURY WHEN

PERFORMING STRAPPING OPERATIONS.

RAPIDLY UNCOILING STRAPPING MAY

CAUSE INJURY. DIRECT STRAPPING

AWAY FROM PERSONNEL WHEN CUTTING

STRAPPING UNDER TENSION.

PARTIAL UNIT LOADS

1. FOR THE PURPOSE OF THIS UNIT LOAD INSTRUCTION A FULL LAYER OF CONTAINERS

CONSISTS OF FIVE (5) LOADED OR EMPTY CONTAINERS POSITIONED SIDE BY SIDE HORIZONTALLY.

MIXED UNIT LOADS OF EMPTY AND LOADED CONTAINERS ARE PERMITTED. EMPTY CONTAINERS SHALL BE PLACED ON THE UPPER MOST LAYERS. IF A LAYER CONTAINS A MIX OF EMPTY AND LOADED CONTAINERS, THE LOADED CONTAINERS SHALL BE PLACED TOWARD THE CENTER OF THE UNIT LOAD.

LESS THAN FULL UNIT LOADS, (FIVE (5) FULL LAYERS OR LESS ), ARE PERMITTED. THE LENGTH

OF BATTENS AND STRAPS, ITEMS 4 THRU 9, SHALL BE ADJUSTED PROPORTIONALLY.

DEPALLETIZING PROCEDURE

1. CUT AND REMOVE STRAPPING.

2. REMOVE UPPER UPPER PLYWOOD AND SIDE/END BATTENS

3. REMOVE CONTAINERS.

NAVSEA

DWG NO. 7516334 REV.C SIZE A CAGE CODE

53711

(41.50)

NAVSEA

DWG NO. 7516334

DETAIL A

REV. C SIZE A

.--2.75 TYP

CAGE CODE

53711