N0016421RWP77_sol.pdf

CODE

(Hour)

PAGE(S)

until 04:00 PM local time 14 Jun 2021

X

A X B X C X D

EX

X

G F 74 - 87

88 - 98 X H 99 - 104 susan.eckerle@navy.mil

RATING PAGE OF PAGES

7. ISSUED BY

(Date)

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

Previous Edition is Unusable 33-134 STANDARD FORM 33 (REV. 9-97)

Prescribed by GSA FAR (48 CFR) 53.214(c)

DO-A7 1 104

(If other than Item 7)

15A. NAME 16. NAME AND TITLE OF PERSON AUTHORIZED TO

AND

ADDRESS

SIGN OFFER (Type or print)

OF

OFFEROR

AMENDMENT NO. DATE

15B. TELEPHONE NO (Include area code) 17. SIGNATURE15C. CHECK IF REMITTANCE ADDRESS

IS DIFFERENT FROM ABOVE - ENTER

SUCH ADDRESS IN SCHEDULE.

18. OFFER DATE

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 700)

2. CONTRACT NO.

N00164 8. ADDRESS OFFER TO

See Item 7

9. Sealed offers in original and 1 copies for furnishing the supplies or services in the Schedule will be received at the place specified in Item 8, or if handcarried, in the depository located in

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and

See Section L conditions contained in this solicitation.

10. FOR INFORMATION

CALL:

A. NAME (NO COLLECT CALLS)

SUSAN ECKERLE (812) 854-6538

11. TABLE OF CONTENTS

SOLICITATION/ CONTRACT FORM

SUPPLIES OR SERVICES AND PRICES/ COSTS

2 - 11

X I CONTRACT CLAUSES

DESCRIPTION/ SPECS./ WORK STATEMENT X

PACKAGING AND MARKING

12 - 27 28 - 29

J LIST OF ATTACHMENTS

INSPECTION AND ACCEPTANCE

DELIVERIES OR PERFORMANCE

30 - 32 33 - 34

X K

REPRESENTATIONS, CERTIFICATIONS AND

OTHER STATEMENTS OF OFFERORS

CONTRACT ADMINISTRATION DATA 35 - 43 X

SPECIAL CONTRACT REQUIREMENTS

OFFER (Must be fully completed by offeror) 44 - 45 X M

L INSTRS., CONDS., AND NOTICES TO OFFERORS

EVALUATION FACTORS FOR AWARD

NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. DISCOUNT FOR PROMPT PAYMENT

(See Section I, Clause No. 52.232-8)

14. ACKNOWLEDGMENT OF AMENDMENTS

(The offeror acknowledges receipt of amendments

AMENDMENT NO. DATE

to the SOLICITATION for offerors and related documents numbered and dated):

FACILITY

12. In compliance with the above, the undersigned agrees, if this offer is accepted within calendar days (60 calendar days unless a different period

SOLICITATION, OFFER AND AWARD

X

(X) SEC. DESCRIPTION (X) SEC. DESCRIPTION PAGE(S)

PART I - THE SCHEDULE

26. NAME OF CONTRACTING OFFICER (Type or print) 27. UNITED STATES OF AMERICA 28. AWARD DATE

EMAIL:TEL: (Signature of Contracting Officer)

CODE CODE

B. TELEPHONE (Include area code) C. E-MAIL ADDRESS

AWARD (To be completed by Government)

19. ACCEPTED AS TO ITEMS NUMBERED 20. AMOUNT 21. ACCOUNTING AND APPROPRIATION

22. AUTHORITY FOR USING OTHER THAN FULL AND OPEN COMPETITION:

10 U.S.C. 2304(c)( ) 41 U.S.C. 253(c)( ) (4 copies unless otherwise specified)

23. SUBMIT INVOICES TO ADDRESS SHOWN IN ITEM

24. ADMINISTERED BY (If other than Item 7) CODE 25. PAYMENT WILL BE MADE BY CODE

PART IV - REPRESENTATIONS AND INSTRUCTIONS

PART III - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACHMENTS

46 - 72

PART II - CONTRACT CLAUSES

NAVAL SURFACE WARFARE CENTER CRANE DIV

S. ECKERLE (812-854-6538)

BLDG 121

300 HWY 361

CRANE IN 47522-5001

812-854-6538

FAX:

TEL:

FAX:

TEL:

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid" and "bidder".

SOLICITATION

6. REQUISITION/PURCHASE NO.5. DATE ISSUED

12 May 2021

4. TYPE OF SOLICITATION

SEALED BID (IFB)

NEGOTIATED (RFP)

[ X ]

3. SOLICITATION NO.

N0016421RWP77

Section B - Supplies or Services and Prices

ITEM NO SUPPLIES/SERVICES MAX QTY U/I UNIT PRICE MAX AMOUNT

0001 First Article Manufacture and

Testing

UNDEFINED

of AN/SPG-62 Waveguide Assembly Kit (13 Piece Kit) in accordance with Statement of Work.

First Article test will be waived by the Government if offeror has manufactured this requirement within the past three (3) years.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

FOR UNIT PRICING.

PSC: 5985

FOB: Destination

FFP

0002 First Article Manufacture and

Testing of Rev J Waveguide Assembly, MK82 W5 (P/N 5204696) in accordance with Statement of Work.

First Article test will be waived by the Government if offeror has manufactured this requirement within the past three (3) years.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0003 AN/SPG-62 Waveguide

Assembly Kit

New manufacture of AN/SPG-62 Waveguide Assembly Kit (13 Piece Kit) in accordance with Statement of

Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0004 Waveguide Assembly W1

New manufacture of Waveguide Assembly W1 (P/N 7265503-1) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0005 Waveguide Assembly W2

New manufacture of Waveguide Assembly W2 (P/N 2904953-5) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0006 Waveguide Assembly W3

New manufacture of Waveguide Assembly W3 (P/N 3257782) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0007 Waveguide Assembly W4

New manufacture of Waveguide Assembly W4 (P/N 3257781) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0008 Waveguide Assembly W5

New manufacture of Waveguide Assembly W5 (P/N 3257779) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0009 Waveguide Assembly W6

New manufacture of Waveguide Assembly W5 (P/N 3257780) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0010 Waveguide Assembly W7

New manufacture of Waveguide Assembly (P/N 2917420) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0011 Waveguide Assembly W8

New manufacture of Waveguide Assembly W8 (P/N 2917419) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0012 Dummy Load AT1

New manufacture of Dummy Load AT1 (P/N 2904954-1) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0013 Directional Coupler DC1

New manufacture of Directional Coupler DC1 (P/N 2902469) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0014 Directional Coupler DC2

New manufacture of Directional Coupler DC2 (P/N 5204716) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0015 Waveguide Horn E1

New manufacture of Waveguide Horn EI (P/N 7253197-50) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0016 Ancillary Waveguide Horn E2

New manufacture of Ancillary Waveguide Horn E2 (P/N 7253199-50) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

0017 Waveguide Assembly MK82 W5

New manufacture of Waveguide Assembly MK82 W5 (P/N 5204696) in accordance with Statement of Work.

Offerors shall provide proposed price for this CLIN on the price matrix below. SEE PRICE MATRIX BELOW

ITEM NO SUPPLIES/SERVICES QTY U/I UNIT PRICE AMOUNT

0018 Technical Data Requirements

1 Lot for CLINs 0001 thru 0017 in accordance with (IAW) the Statement of Work (SOW) Paragraph(s) 3.1.6, 3.2.1, and 3.4.2; CDRL(s) A001 thru A003 provided in Section J, and applicable DID(s).

Not Separately Priced

PRICE MATRIX

OFFERORS SHALL COMPLETE THE FOLLOWING PRICE MATRIX FOR CLIN 0001

THROUGH CLIN 0017, IN THE QUANTITIES DEEMED APPROPRIATE. OFFERORS

CAN ADD ADDITIONAL ROWS AS NECESSARY, AND DO NOT HAVE TO USE EACH

ROW BELOW.

CLIN 0001 PRICE MATRIX

Quantity Year 1 Price

(Each)

CLIN 0002 PRICE MATRIX

Quantity Year 1 Price

CLIN 0003 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

4-10 11-20

CLIN 0004 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0005 PRICE MATRIX

Quantity Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0006 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0007 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0008 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0009 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0010 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0011 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0012 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0013 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0014 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0015 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0016 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

(Each) 1-3

CLIN 0017 PRICE MATRIX

Year 1 Price

(Each) Year 2 Price

(Each) Year 3 Price

(Each) Year 4 Price

(Each) Year 5 Price

1-3

IDC CONSTRAINTS

CONTRACT MINIMUM/MAXIMUM QUANTITY AND CONTRACT VALUE

The minimum quantity and contract value for all orders issued against this contract shall not be less than the minimum quantity and contract value stated in the following table. The maximum quantity and contract value for all orders issued against this contract shall not exceed the maximum quantity and contract value stated in the following table.

MINIMUM

QUANTITY

MINIMUM

AMOUNT

MAXIMUM

QUANTITY

MAXIMUM

AMOUNT

2.00 $5,744,908.00

IDC CONSTRAINTS NOTE

NOTE: Minimum Quantity shall be met by one (1) each of CLIN 0001 and CLIN 0002 if First Article is applicable.

If First Article is waived, Minimum Quantity shall be met by one (1) each of CLIN 0003 and CLIN 0017.

Section C - Descriptions and Specifications

CLAUSES INCORPORATED BY FULL TEXT

C-202-H001 ADDITIONAL DEFINITIONS–BASIC (NAVSEA) (OCT 2018)

(a) Department - means the Department of the Navy.

(b) Commander, Naval Sea Systems Command - means the Commander of the Naval Sea Systems Command of the Department of the Navy or his duly appointed successor.

(c) References to The Federal Acquisition Regulation (FAR) - All references to the FAR in this contract shall be deemed to also reference the appropriate sections of the Defense FAR Supplement (DFARS), unless clearly indicated otherwise.

(d) National Stock Numbers - Whenever the term Federal Item Identification Number and its acronym FIIN or the term Federal Stock Number and its acronym FSN appear in the contract, order or their cited specifications and standards, the terms and acronyms shall be interpreted as National Item Identification Number (NIIN) and National Stock Number (NSN) respectively which shall be defined as follows:

(1) National Item Identification Number (NIIN). The number assigned to each approved Item Identification under the Federal Cataloging Program. It consists of nine numeric characters, the first two of which are the National Codification Bureau (NCB) Code. The remaining positions consist of a seven digit non-significant number.

(2) National Stock Number (NSN). The National Stock Number (NSN) for an item of supply consists of the applicable four-position Federal Supply Class (FSC) plus the applicable nine-position NIIN assigned to the item of supply.

(End of text)

C-204-H001 USE OF NAVY SUPPORT CONTRACTORS FOR OFFICIAL CONTRACT FILES (NAVSEA)

(OCT 2018)

(a) NAVSEA may use a file room management support contractor, hereinafter referred to as "the support contractor", to manage its file room, in which all official contract files, including the official file supporting this procurement, are retained. These official files may contain information that is considered a trade secret, proprietary, business sensitive or otherwise protected pursuant to law or regulation, hereinafter referred to as “protected information”. File room management services consist of any of the following: secretarial or clerical support; data entry; document reproduction, scanning, imaging, or destruction; operation, management, or maintenance of paper-based or electronic mail rooms, file rooms, or libraries; and supervision in connection with functions listed herein.

(b) The cognizant Contracting Officer will ensure that any NAVSEA contract under which these file room management services are acquired will contain a requirement that:

(1) The support contractor not disclose any information;

(2) Individual employees are to be instructed by the support contractor regarding the sensitivity of the official contract files;

(3) The support contractor performing these services be barred from providing any other supplies and/or services, or competing to do so, to NAVSEA for the period of performance of its contract and for an additional three years thereafter unless otherwise provided by law or regulation; and,

(4) In addition to any other rights the contractor may have, it is a third party beneficiary who has the right of direct action against the support contractor, or any person to whom the support contractor has released or disclosed protected information, for the unauthorized duplication, release, or disclosure of such protected information.

(c) Execution of this contract by the contractor is considered consent to NAVSEA's permitting access to any information, irrespective of restrictive markings or the nature of the information submitted, by its file room management support contractor for the limited purpose of executing its file room support contract responsibilities.

(d) NAVSEA may, without further notice, enter into contracts with other contractors for these services. Contractors should enter into separate non-disclosure agreements with the file room contractor. Contact the Procuring Contracting Officer for contractor specifics. However, any such agreement will not be considered a prerequisite before information submitted is stored in the file room or otherwise encumber the government.

C-209-H002 FIRST ARTICLE (GOVERNMENT TESTING) (NAVSEA) (OCT 2018)

(a) The First Article shall conform in every respect to the requirements of this contract. The First Article shall be manufactured with tools, materials, and methods which are the same as the tools, material and methods which will be used to manufacture the production units. All items delivered under the contract shall be manufactured under the same conditions and quality established by the First Article. Any changes to tools, material, or methods after the first article approval shall be documented by the contractor and approved by the Contracting Officer before they are used.

The First Article shall not be delivered for first article approval tests as provided for in the clause of this contract entitled "First Article Approval--Government Testing" (FAR 52.209-4) until after the Contractor has fully tested it, at its expense, to determine compliance with said requirements.

(b) The Contractor shall make a record of all data obtained during such tests in a form similar to the guidance provided in MIL-HDBK-831A.

C-209-H003 WAIVER OF FIRST ARTICLE REQUIREMENTS (NAVSEA) (OCT 2018)

If the First Article is waived by the Government, the Contractor shall deliver supplies that are identical or substantially identical to those previously accepted by the Government under the following contract(s):

(Offeror to fill in contract number(s), as applicable. See Section M)

(End of Text)

C-211-H016 SPECIFICATIONS AND STANDARDS (NAVSEA) (OCT 2018)

(a) Definitions.

(i) A "zero-tier reference" is a specification, standard, or drawing that is cited in the contract (including its attachments).

(ii) A "first-tier reference" is either: (1) a specification, standard, or drawing cited in a zero-tier reference, or (2) a specification cited in a first-tier drawing.

(b) Requirements. All zero-tier and first-tier references, as defined above, are mandatory for use. All lower tier references shall be used for guidance only unless specifically identified below.

None

C-211-H017 UPDATING SPECIFICATIONS AND STANDARDS (NAVSEA) (DEC 2018)

The contractor may request that this contract be updated to include the current version of the applicable specification or standard if the update does not affect the form, fit or function of any deliverable item or increase the cost/price of the item to the Government. The contractor should submit update requests to the Procuring Contracting Officer with copies to the Administrative Contracting Officer and cognizant program office representative for approval. The contractor shall perform the contract in accordance with the existing specifications and standards until notified of approval/disapproval of its request to update by the Procuring Contracting Officer. Any approved alternate specifications or standards will be incorporated into the contract.

C-211-H018 APPROVAL BY THE GOVERNMENT (NAVSEA) (JAN 2019)

Approval by the Government as required under this contract and applicable specifications shall not relieve the Contractor of its obligation to comply with the specifications and with all other requirements of the contract, nor shall it impose upon the Government any liability it would not have had in the absence of such approval.

C-215-H002 CONTRACTOR PROPOSAL (NAVSEA) (OCT 2018)

(a) Performance of this contract by the Contractor shall be conducted and performed in accordance with the detailed obligations to which the Contractor committed itself in Proposal dated in response to Solicitation No.

N0016421RWP77.

(b) The technical volume(s) of the Contractor's proposal is(are) hereby incorporated by reference and made subject to the "Order of Precedence" (FAR 52.215-8) clause of this contract. Under the "Order of Precedence" clause, the technical volume(s) of the Contractor's proposal referenced herein is (are) hereby designated as item (f) of the clause, following "the specifications" in the order of precedence.

C-227-H006 DATA REQUIREMENTS (NAVSEA) (OCT 2018)

The data to be furnished hereunder shall be prepared in accordance with the Contract Data Requirements List, DD Form 1423, Exhibit(s) A, attached hereto.

C-242-H001 EXPEDITING CONTRACT CLOSEOUT (NAVSEA) (OCT 2018)

(a) As part of the negotiated fixed price or total estimated amount of this contract, both the Government and the Contractor have agreed to waive any entitlement that otherwise might accrue to either party in any residual dollar amount of $1,000 or less at the time of final contract closeout. The term "residual dollar amount" shall include all money that would otherwise be owed to either party at the end of the contract, except that, amounts connected in any way with taxation, allegations of fraud and/or antitrust violations shall be excluded. For purposes of determining residual dollar amounts, offsets of money owed by one party against money that would otherwise be paid by that party may be considered to the extent permitted by law.

(b) This agreement to waive entitlement to residual dollar amounts has been considered by both parties. It is agreed that the administrative costs for either party associated with collecting such small dollar amounts could exceed the amount to be recovered.

C-245-H005 INFORMATION AND C-245-H005 INFORMATION AND DATA FURNISHED BY THE

GOVERNMENT--ALTERNATE I (NAVSEA) (MAY 2019)

(a) Contract Specifications, Drawings and Data. The Government will furnish, if not included as an attachment to the contract, any unique contract specifications or other design or alteration data cited or referenced in Section C.

(b) Government Furnished Information (GFI). GFI is defined as that information essential for the installation, test, operation, and interface support of all Government Furnished Material identified in an attachment in Section J. The Government shall furnish only the GFI identified in an attachment in Section J. The GFI furnished to the contractor need not be in any particular format. Further, the Government reserves the right to revise the listing of GFI as follows:

(1) The Contracting Officer may at any time by written order:

(i) delete, supersede, or revise, in whole or in part, data identified in an attachment in Section J; or

(ii) add items of data or information to the attachment identified in Section J; or

(iii) establish or revise due dates for items of data or information in the attachment identified in Section J.

(2) If any action taken by the Contracting Officer pursuant to subparagraph (1) immediately above causes an increase or decrease in the costs of, or the time required for, performance of any part of the work under this contract, the contractor may be entitled to an equitable adjustment in the contract amount and delivery schedule in accordance with the procedures provided for in the "CHANGES" clause of this contract.

(c) Except for the Government information and data specified by paragraphs (a) and (b) above, the Government will not be obligated to furnish the Contractor any specification, standard, drawing, technical documentation, or other publication, notwithstanding anything to the contrary in the contract specifications, the GFI identified in an attachment in Section J, the clause of this contract entitled "Government Property" (FAR 52.245-1) or "Government

Property Installation Operation Services" (FAR 52.245-2), as applicable, or any other term or condition of this contract. Such referenced documentation may be obtained:

(1) From the ASSIST database via the internet at https://assist.dla.mil/online/start/; or

(2) By submitting a request to the

Department of Defense Single Stock Point (DoDSSP)

Building 4, Section D

700 Robbins Avenue Philadelphia, Pennsylvania 19111-5094 Telephone (215) 697-6396 Facsimile (215) 697-9398.

Commercial specifications and standards, which may be referenced in the contract specification or any sub-tier specification or standard, are not available from Government sources and should be obtained from the publishers.

C-246-H002 GOVERNMENT USE OF CONTRACTOR’S INSPECTION EQUIPMENT (NAVSEA) (OCT 2018)

The contractor's gages, measuring, and testing devices shall be made available to the Government when required to determine contractor conformance with contract requirements. If conditions warrant, the contractor’s personnel shall be made available for operation of such devices and for verification of their accuracy and condition.

C-247-H001 PERMITS AND RESPONSIBILITIES (NAVSEA) (DEC 2018)

The Contractor shall, without additional expense to the Government, be responsible for obtaining any necessary licenses and permits for complying with any applicable Federal, State, and Municipal laws, codes, and regulations for shipping and transportation including, but not limited to, any movement over public highways of overweight/over dimensional materials.

STATEMENT OF WORK

STATEMENT OF WORK

MK99 FIRE CONTROL SYSTEM (FCS) WAVEGUIDE

ASSEMBLIES 06 May 2021

1.0 BACKGROUND AND SCOPE

This Statement of Work (SOW) establishes the requirements for the manufacture, qualification, inspection, and delivery of the following SPG-62 Waveguide Assemblies: Dummy Load AT1, PN 2904954-1; Directional Coupler DC1, PN 2902469; Directional Coupler DC2, PN 5204716; Waveguide Horn E1, PN 7253197-50;

Ancillary Waveguide Horn E2, PN 7253199-50; Waveguide Assembly W1, PN 7265503-1; Flexible Waveguide Assembly W2, PN 2904953-4; Waveguide Assembly W3, PN 3257782; Waveguide Assembly W4, PN 3257781;

Waveguide Assembly W5, PN 3257779; Waveguide Assembly W6, PN 3257780; Waveguide Assembly W7, 2917420; Waveguide Assembly W8, 2917419; and MK82 Waveguide Assembly W5, PN 5204696; used in the MK99 Fire Control System (FCS). Naval Surface Warfare Center (NSWC) Crane Division is the designated overhaul point for the SPG-62 Antenna and MK-82 Director, subsystems of the MK-99 FCS.

2. 0 APPLICABLE DOCUMENTS

The following documents of the revision or issue in effect at the date of award, form a part of this SOW for reference. In the event of conflict between the documents referenced herein and the contents of this SOW, the contents of this SOW shall prevail.

2.1 MILITARY STANDARDS

MIL-STD-129P Military Marking for Shipment and Storage

MIL-STD-130N Identification Marking of U.S. Military Property

2.2 SPECIFICATIONS/DRAWINGS

2902469 Rev N Coupler, Directional CWI, DC1

2917419 Rev L Waveguide Assembly, W8

2917420 Rev M Waveguide Assembly, W7

3257779 Rev F Waveguide Assembly, W5

3257780 Rev G Waveguide Assembly, W6

3257781 Rev H Waveguide Assembly, W4

3257782 Rev K Waveguide Assembly, W3

5204716 Rev F Coupler Directional, DC2

5204696 Rev J Waveguide Assembly, MK82 W5

2904953 Rev AB Waveguide Assembly, W2

2904954 Rev D Dummy Load Electrical, AT1

7253197 Rev - Horn Waveguide CWI, E1

7253199 Rev F Horn Waveguide CWI Ancillary, E2

7265503 Rev - Waveguide Assembly Special Ground, W1

2898001 Rev A Electrical Parameters (Classified)

7253155 Rev A Waveguide Seal Bonding Process

OD15448 Rev - Plating, Process

OD32195 Rev B Environmental Specification for AEGIS System

WS9775 Rev R Process Specification, Wiring, Equipment

WS9778 Rev L Paint System, Semi-Gloss

WS10012 Rev AD Enamel Paint System, Low Volatile Organic Content Epoxy, Semi-Gloss, Process

WS10094 Rev A Vanish, Process

WS10245 Rev U Quality Assurance Provisions

WS23690 Rev H Weatherproofing, Waveguide Flanges

2.3 INDUSTRY STANDARDS

ISO 9001-2008 Quality Management

NIST Special Publication 800-171

Protecting Unclassified Information in Nonfederal Information Systems and Organizations

3.0 REQUIREMENTS

3.1 General Requirements:

3.1.1 The contractor shall furnish all equipment, parts, and labor necessary to manufacture and test the following SPG-62 Antenna Waveguide Assemblies individually and/or as a collective thirteen piece (13) kit:

Piece/Part Number (PN)

Dummy Load AT1/ PN 2904954-1

Directional Coupler DC1/PN 2902469

Directional Coupler DC2/PN 5204716

Waveguide Horn E1/PN 7253197-50

Ancillary Waveguide Horn E2/PN 7253199-50

Waveguide Assembly W1/PN 7265503-1

Flexible Waveguide Assembly W2/PN 2904953-5

Waveguide Assembly W3/PN 3257782

Waveguide Assembly W4/PN 3257781

Waveguide Assembly W5/PN 3257779

Waveguide Assembly W6/PN 3257780

Waveguide Assembly W7/PN 2917420

Waveguide Assembly W8/PN 2917419

3.1.2 The contractor shall furnish all equipment, parts, and labor necessary to manufacture and test the following MK-82 Director Waveguide Assemblies:

Waveguide Assembly MK82 W5 (PN 5204696)

3.1.3 The contractor shall be responsible for shipment of all manufactured Waveguide Assemblies to and from NSWC Crane, Building 3168.

3.1.4 For Waveguide Assemblies to be delivered to the Government, the contractor shall perform marking for shipment and storage processes using MIL-STD-129P.

3.1.5 For Waveguide Assemblies to be delivered to the Government, the contractor shall apply equipment markings and identification processes using MIL-STD-130N.

3.1.6 In the event it is necessary to deviate from the drawings provided based on obsolescence or diminished manufacturing sources and material shortages (DMSMS), the contractor shall formally request the change in an engineering change proposal (ECP) and submit it to the government for approval.

Research documentation and test data supporting the proposed change shall be made available to the government upon request. The government will require adequate time to review ECP's based on the magnitude of the change. Furthermore, an updated technical drawing package reflecting the changes must be provided to the government. The updated Government owned TDP may or may not need to accompany the ECP for approval depending on whether or not it is needed to adequately describe the change. (CDRL A001, Technical Data Package; CDRL 0002, Engineering Change Proposal)

3.2 Initial Testing Requirements

3.2.1 If the contractor or subcontractor producing the assembly/part HAS NOT manufactured the assemblies as stated in 3.1.1 & 3.1.2 within the last 3 years the contractor shall perform and provide initial testing requirement IAW Paragraph 3.2.3 of this SOW for each initial waveguide assembly manufactured. If contractor changes manufacturing process for any of the subassemblies then the contractor shall provide all applicable testing data and documentation to the Government. The initial testing shall be performed by the contractor with a government witness. The contractor shall make personnel available to respond to questions from the Government. Contractor shall provide all initial testing data and documentation to the Government in a Test Inspection report. (CDRL A003, Test Inspection Report)

3.2.2 If the contractor or subcontractor producing the assembly/part has manufactured the assemblies as stated in 3.1.1 & 3.1.2 within the last 3 years the contractor shall provide applicable certification data (coordinate measurement data and qualifications) IAW Paragraph 3.2.3 of this SOW for review.

3.2.3 Waveguide Assemblies Initial Testing Requirements

3.2.3.1 2904954-1 – Dummy Load AT1

3.2.3.1.1 Vendor shall provide all reports/data per drawing number 2904954 paragraph 5.

3.2.3.1.2 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.2 2902469 – Directional Coupler DC1

3.2.3.2.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.3 5204716 – Directional Coupler DC2

3.2.3.3.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.4 7253197-50 – Waveguide Horn E1

3.2.3.4.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.5 7253199-50 – Ancillary Waveguide Horn E2

3.2.3.5.1 Vendor shall provide all reports/data per drawing number 7253198 Note 1.5.

3.2.3.5.1.1 For lot size 1-3 the sample size shall match lot size.

3.2.3.5.1.2 Radiographic inspection required.

3.2.3.5.2 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.6 7265503-1 – Waveguide Assembly W1

3.2.3.6.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.7 2904953-4 – Waveguide Assembly W2

3.2.3.7.1 Vendor shall provide all reports/data per drawing number 2904953 paragraph 7.3.

3.2.3.7.2 Vendor shall provide all reports/data per drawing number 2904953 paragraph 7.5.

3.2.3.7.3 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.8 3257782 – Waveguide Assembly W3

3.2.3.8.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.9 3257781 – Waveguide Assembly W4

3.2.3.9.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.10 3257779 - Waveguide Assembly W5

3.2.3.10.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.11 Waveguide Assembly W6

3.2.3.11.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.12 2917420 – Waveguide Assembly W7

3.2.3.12.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.13 2917419 – Waveguide Assembly W8

3.2.3.13.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.2.3.14 5204696 – Waveguide Assembly W5

3.2.3.14.1 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.3 Waveguide Assemblies Testing Requirements

3.3.1.1 2904954-1 – Dummy Load AT1

3.3.1.1.1 Vendor shall provide all reports/data per drawing number 2904954 paragraph 3.

3.3.1.1.2 Vendor shall provide all reports/data per drawing number 2904954 paragraph 4.6.

3.3.1.2 2902469 – Directional Coupler DC1

3.3.1.2.1 Vendor shall provide all reports/data per drawing number 2902469 Note 8.

3.3.1.2.2 Vendor shall provide all reports/data per drawing number 2902469 Note 9.

3.3.1.2.3 Vendor shall provide all reports/data per drawing number 2902469 Note 10.

3.3.1.2.4 Vendor shall provide all reports/data per drawing number 2902469 Note 11.

3.3.1.3 5204716 – Directional Coupler DC2

3.3.1.3.1 Vendor shall provide all reports/data per drawing number 5204716 Note 8.

3.3.1.3.2 Vendor shall provide all reports/data per drawing number 5204716 Note 9.

3.3.1.4 7253197-50 – Waveguide Horn E1

3.3.1.4.1 Vendor shall provide all reports/data per drawing number 7253197 Note 5.

3.3.1.4.2 Vendor shall provide all reports/data per drawing number 7253197 Note 11.

3.3.1.5 7253199-50 – Ancillary Waveguide Horn E2

3.3.1.5.1 Vendor shall provide all reports/data per drawing number 7253198 Note 1.5.

3.3.1.5.1.1 For lot size 1-3 the sample size shall match lot size.

3.3.1.5.1.2 Radiographic inspection not required.

3.3.1.5.2 Vendor shall provide all reports/data per drawing number 7253198 Note 2.10.

3.3.1.5.3 Vendor shall provide all reports/data per drawing number 7253199 Note 5.

3.3.1.5.4 Vendor shall provide all reports/data per drawing number 7253199 Note 11.

3.3.1.6 7265503-1 – Waveguide Assembly W1

3.3.1.6.1 Vendor shall provide all reports/data per drawing number 3257783 Note 5.

3.3.1.6.2 Vendor shall provide all reports/data per drawing number 3257783 Note 11.

3.3.1.7 2904953-4 – Waveguide Assembly W2

3.3.1.7.1 Vendor shall provide all reports/data per drawing number 2904953 paragraph 7.4.

3.3.1.8 3257782 – Waveguide Assembly W3

3.3.1.8.1 Vendor shall provide all reports/data per drawing number 3257782 Note 5.

3.3.1.8.2 Vendor shall provide all reports/data per drawing number 3257782 Note 12.

3.3.1.9 3257781 – Waveguide Assembly W4

3.3.1.9.1 Vendor shall provide all reports/data per drawing number 3257781 Note 5.

3.3.1.9.2 Vendor shall provide all reports/data per drawing number 3257781 Note 12.

3.3.1.10 3257779 – Waveguide Assembly W5

3.3.1.10.1 Vendor shall provide all reports/data per drawing number 3257779 Note 7.

3.3.1.10.2 Vendor shall provide all reports/data per drawing number 3257779 Note 14.

3.3.1.10.3 Coordinate Measurement of all dimensions in accordance with the applicable drawing.

3.3.1.11 3257780 – Waveguide Assembly W6

3.3.1.11.1 Vendor shall provide all reports/data per drawing number 3257780 Note 7.

3.3.1.11.2 Vendor shall provide all reports/data per drawing number 3257780 Note 15.

3.3.1.12 2917420 – Waveguide Assembly W7

3.3.1.12.1 Vendor shall provide all reports/data per drawing number 2917420 Note 8.

3.3.1.12.2 Vendor shall provide all reports/data per drawing number 2917420 Note 11.

3.3.1.13 2917419 – Waveguide Assembly W8

3.31.13.1 Vendor shall provide all reports/data per drawing number 2917419 Note 8.

3.3.1.13.2 Vendor shall provide all reports/data per drawing number 2917419 Note 11.

3.3.1.14 5204696 – Waveguide Assembly W5

3.3.1.14.1 Vendor shall provide all reports/data per drawing number 5204696 Note 6.

3.3.1.14.2 Vendor shall provide all reports/data per drawing number 5204696 Note 13.

3.4 Waveguide Assembly Manufacturing

3.4.1 Newly manufactured waveguide sections shall be tuned to meet Voltage Standing Wave Ratio (VSWR) specifications per the drawings provided. Insertion of any ceramic, ferrite, dielectric or tuning posts is prohibited.

Mechanical dimensions prescribed by the referenced drawings shall drive electrical performance.

3.4.2 Dent tuning is permissible as required. Accompanying test data shall indicate if dent tuning was performed.

All dents resulting from dent tuning shall be filled and painted so that the end items have a smooth, clean, and new appearance. (CDRL A003, Test Inspection Report)

3.4.3 As indicated by delivery order, material finishing requirements of WS9778 specified within the applicable documents of paragraph 2.0 are to be waived to meet requirements of paragraphs 3.4.3.1 thru 3.4.3.3.

3.4.3.1 Aluminum Surfaces

3.4.3.1.1 Surface Preparation

3.4.3.1.1.1 Per NACE 3/SSPC-SP6

3.4.3.1.2 Coating System

3.4.3.1.2.1 First Coat – Ameron Amercoat 68HS zinc-rich primer, 3-5 mils (Dry-Film Thickness) DFT

3.4.3.1.2.2 Second Coat – Ameron PSX 700 Engineered Siloxane coating, 3-5 mils DFT 3.4.3.1.2.3 Third Coat – Ameron PSX 700 Engineered Siloxane coating, FED-STD-595 Color

#26270, 3-5 mils DFT

3.4.3.2 Cooper Surfaces

3.4.3.2.1 Surface Preparation

3.4.3.2.1.1 Per NACE 2/SSPC-SP10

3.4.3.2.2 Coating System

3.4.3.2.2.1 First Coat – Ameron PSX 700 Engineered Siloxane coating, 3-5 mils DFT

3.4.3.2.2.2 Second Coat – Ameron PSX 700 Engineered Siloxane coating, FED-STD-595 Color #26270, 3-5 mils DFT

3.4.3.3 Notes

3.4.3.3.1 Only dry abrasive blast cleaning techniques shall be used.

3.4.3.3.2 Use aluminum oxide, sponge-jet aluminum oxide silver sponge, mineral quartz sand, or nonquartz abrasive media. Size shall be selected to give an anchor tooth profile of 1.5 -2.5 mils.

3.4.3.3.3 Obtain accurate Volatile Organic Compounds (VOC) level of thinners from coating manufacturer. Use thinners specified by coating manufacturer for each product (coating) being applied.

3.4.3.3.4 In order to achieve good flow (wetting) characteristics for thin coatings, atomization of paint spray gun without exceeding local maximum allowable VOC levels may be required.

3.4.3.3.5 Avoid mixing partial kits. Partial kits may only be used when performing local touch up/repairs. Mixing ratio of each coating component (i.e., base (resin), zinc powder, catalyst (cure), etc.) shall be in accordance with coating manufacturer specifications.

3.4.3.3.6 Applies to 3.4.3.1 ONLY. When applying zinc-rich coatings, constant mixing of the paint is required during application. If a pressure tank is used during application, it must be equipped with an agitator assembly to continuously stir the paint. If a High Volume Low Pressure (HVLP) pressure assist cup or a siphon cup is used, clean 3/8" diameter 316 stainless steel balls must be placed into the cup and the gun frequently (i.e., every 2 minutes) agitated by hand.

3.4.3.3.7 Applies to 3.4.3.1 ONLY. The high concentration of zinc metal powder inhibits the ability of Wet Film Thickness (WFT) gages to produce an accurate reading. WFT gage shall be used to obtain approximate WFT readings. WFT gage will yield a lower result than actual WFT.

3.4.3.3.8 When performing coating preparation, application, and cure operations, ambient and prepared metal substrate surface temperatures shall be between 60°F and 90°F, surface temperature shall be a maximum of 5°F above dew point temperature and relative humidity shall be less than 85%.

3.4.3.3.9 Dry-to-recoat window is defined as a window in which reactivation (i.e., washing, abrading, etc.)

of the previously applied coating is not required to attain a strong chemical and mechanical bond to a new paint coat. In addition, sufficient solvents have evaporated and the previously applied coating has solidified enough to safely allow application of more coatings. Do not exceed a 65 hour recoat window for zinc-rich epoxy coatings.

3.4.3.3.10 If the dry-to-recoat window of the previously applied coating is exceeded, all surfaces must be reactivated before applying another coating by either following the manufacturer instructions for reactivating the surface or cleaning the entire surface using a fresh water and detergent wash, followed by a fresh water rinse. After allowing the surface to dry, the surface shall be lightly abraded using a brush-off abrasive blast, power sanding, or hand sanding followed by vacuuming and SSPC-SP1 solvent wipe using reagent grade isopropyl alcohol (99% minimum alcohol content).

3.4.3.3.11 Dry-to-hard cure time is defined as the time required for an applied coating to reach a fully cured condition through the entire cross-section of the coating film. At this point, a new coating will not chemically bond (adhere) to the previous coat.

3.4.3.3.12 After mixing and thinning, all coatings must be filtered through a paint strainer.

3.4.3.3.13 Use a dedicated fluid hose for zinc-rich epoxy coatings and a second fluid hose for other coatings to minimize contamination.

3.4.3.3.14 To provide contrast and thus help ensure that an even, uniform Wet Coating Film is being applied, each coating layer shall be of a different contrasting color.

3.4.4 The contractor shall manufacture Dummy Load AT1, PN 2904954-1 per the drawing specification of the assembly and subassemblies.

3.4.5 The contractor shall manufacture Directional Coupler DC1, PN 2902469 per the drawing specification of the assembly and subassemblies.

3.4.6 The contractor shall manufacture Directional Coupler DC2, PN 5204716 per the drawing

3.4.7 The contractor shall manufacture Waveguide Horn E1, PN 7253197-50 per the drawing

3.4.8 The contractor shall manufacture Waveguide Horn E2, PN 7253199-50 per the drawing

3.4.9 The contractor shall manufacture Waveguide Assembly W1, 7265503-1 per the drawing

3.4.10 The contractor shall manufacture Waveguide Assembly W2, 2904954-1 per the drawing

3.4.11 The contractor shall manufacture Waveguide Assembly W3, 3257782 per the drawing

3.4.12 The contractor shall manufacture Waveguide Assembly W4, 3257781 per the drawing

3.4.13 The contractor shall manufacture Waveguide Assembly W5, 3257779 per the drawing

3.4.14 The contractor shall manufacture Waveguide Assembly W6, 3257780 per the drawing

3.4.15 The contractor shall manufacture Waveguide Assembly W7, 2917420 per the drawing

3.4.16 The contractor shall manufacture Waveguide Assembly W8, 2917419 per the drawing

3.4.17 The contractor shall manufacture MK82 Waveguide Assembly W5, 5204696 per the drawing

3.4.18 Counterfeit Parts and Materiel

Counterfeit materiel is a serious threat to the safety and operational effectiveness of DoD systems. The Contractor (and subcontractors at all tiers) shall implement a risk mitigation process when obtaining critical or high risk materiel in accordance with paragraphs (a) and (b) below:

(a) If the materiel is currently in production or currently available, the materiel shall be obtained only from authorized sources. Authorized sources are the original manufacturer, a source with the express written authority of the original manufacturer or current design activity, or an authorized aftermarket manufacturer.

(b) If the materiel is not in production or currently available from authorized sources, the materiel shall be obtained from suppliers that meet appropriate counterfeit avoidance criteria. Counterfeit avoidance criteria can be found in the following Industry Standards - SAE AS5553A; SAE AS6462; SAE AS6081; SAE ARP6178; SAE AS6174A; and SAE AS6301.

Contractors shall notify the contracting officer when critical or high risk materiel cannot be obtained from an authorized source. The contractor shall take mitigating actions to authenticate the materiel if purchased from another source.

The contractor shall report instances of counterfeit and suspect counterfeit materiel to the Contracting Officer and the Government-Industry Data Exchange Program (GIDEP) as soon as the contractor becomes aware of the issue.

4.0 GOVERNMENT FURNISHED ITEMS

4.1 GOVERNMENT FURNISHED INFORMATION (GFI): The documents/drawings listed in Section 2 of this SOW will be provided along with associated part lists, subassembly drawings, and specifications owned by the government.

4.2 GOVERNMENT FURNISHED MATERIAL (GFM): The Government will not provide any manufacturing, parts or materials for this tasking.

5.0 DATA DELIVERABLES

The contractor shall submit the following data deliverables shall in accordance with the requirements listed in the Contractor Data Requirements Lists (CDRLs).

CDRL: A001

DID Number: DI-SESS-80776A DID Title: Technical Data Package DID Sub-Title: Technical Data Package SOW Paragraph: 3.1.6

CDRL: A002

DID Number: DI-SESS-80639D DID Title: Engineering Change Proposal (ECP) DID Sub-Title: Manufacturing ECP SOW Paragraph: 3.1.6

CDRL: A003

DID Number: DI-NDTI-80809B DID Title: Test Inspection Report DID Sub-Title: Test Report SOW Paragraph: 3.2.1, 3.4.2

6.0 SPECIAL CONDITIONS

6.1 Quality:

6.1.1 Quality Program. The contractor shall have a quality program that is ISO 9001-2008 compliant or meets the following requirements: monitor and control critical processes; continuously improve processes; establish mechanisms for performance feedback; and maintain an effective root cause analysis and corrective action system.

6.1.2 Quality Assurance. The contractor shall ensure each manufactured subassembly meets all specifications IAW the applicable drawings and subsequent referenced documents. The contractor shall ensure that only approved vendor manufactured parts were used to fulfill requirements of this SOW. The contractor shall ensure that each manufactured assembly has a “Like New” appearance. Workmanship defects and/or transportation damage found upon delivery to the Government will not be accepted.

Workmanship defects and/or transportation damage shall be reworked by the contractor at no additional cost to the Government.

6.2 Security Requirements. Performance on this contract will require the contractor employees who perform VSWR testing to have access to classified information. The contractor shall store classified information up to and including the SECRET level. DD254 Security guidance is applicable and is an attachment in Section J of the contract. SPEC 2898001 Electrical Test is a classified document.

6.2.1 Facility Security Clearance Required. The contractor is required to maintain a SECRET facility security clearance.

6.2.2 Level of Safeguarding for Classified Information/Material Required at Contractor Facility. The contractor is required to maintain a level of safeguarding for classified information/material at the SECRET level.

6.2.3 Controlled Unclassified Information (CUI) (Formerly for Official Use Only Information).

The contractor will be required to have access to Controlled Unclassified Information.

6.2.4 Receive and store classified documents only. The contractor will only receive classified documents for reference purposes. There will be no generation or derivative classification of classified material at the contractor facility.

6.2.5 Operations Security Requirements. The contractor is required to protect critical information associated with this contract to prevent unauthorized disclosure and will observe OPSEC requirements.

Section D - Packaging and Marking

D-211-H001 PACKAGING OF DATA (NAVSEA) (OCT 2018)

Data to be delivered by Integrated Digital Environment (IDE) or other electronic media shall be as specified in the contract.

All unclassified data to be shipped shall be prepared for shipment in accordance with best commercial practice.

Classified reports, data, and documentation shall be prepared for shipment in accordance with National Industrial Security Program Operating Manual (NISPOM), DOD 5220.22-M dated 28 February 2006 incorporating Change 2 dated 18 May 2016.

D-247-H001 ADDITIONAL MARKING REQUIREMENTS FOR FMS ITEMS (NAVSEA) (OCT 2018)

(a) The following identifying marks shall appear on the outside of each box, parcel and/or crate and all shipping papers included in each shipment:

NAVY

FMS CASE _________________________________________________________

REQUISITION NO. ___________________________________________________

ITEM DESCRIPTION _____________________________________________

If a consolidated shipment of several items in one container is forwarded, add to the above information

"CONSOLIDATED SHIPMENT, CONTAINS ____ ITEMS".

(b) The inscription "UNITED STATES OF AMERICA" shall be affixed in a suitable size indelible stencil, label or printed form on all external shipping containers or the exterior surface of uncrated items.

(c) All invoices, correspondence, reports and other documents shall be identified with the appropriate FMS case designator, requisition number(s), and item description(s).

D-247-H002 PACKAGING OF SUPPLIES—BASIC (NAVSEA) (DEC 2020)

Item(s) 0001 through 0017 The supplies furnished hereunder shall be packaged in accordance with ASTM-D-3951-18, Standard Practice for Commercial Packing.

D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018)

The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use.

Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLIN INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY

0001 Destination Government Destination Government 0002 Destination Government Destination Government 0003 Destination Government Destination Government 0004 Destination Government Destination Government 0005 Destination Government Destination Government 0006 Destination Government Destination Government 0007 Destination Government Destination Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 0010 Destination Government Destination Government 0011 Destination Government Destination Government 0012 Destination Government Destination Government 0013 Destination Government Destination Government 0014 Destination Government Destination…