Mobil DTE 732 Oil.pdf

base oil and additives

SAFETY DATA SHEET

Product description

Section 1. Identification

MOBIL DTE 732

Relevant identified uses of the substance or mixture and uses advised against

Identified uses

Uses advised against

: Turbine oil

: This product is not recommended for any industrial, professional or consumer use other than the identified uses above.

MOBIL DTE 732Product name :

Supplier :

22777 Springwoods Village Parkway Spring, TX 77389 USA

24-Hour emergency telephone number

Product Technical Information

800-662-4525

SDS Internet Address www.sds.exxonmobil.com

1-800-424-9300 / +1 703-741-5970 / +1-703-527-3887 (CHEMTREC)

EXXON MOBIL CORPORATION

Section 2. Hazards identification

Not classified.Classification of the substance or mixture

Hazards not otherwise classified

: None known.

OSHA/HCS status : While this material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the safe handling and proper use of the product. This SDS should be retained and available for employees and other users of this product.

This material should not be used for any other purpose than the intended use in Section 1 without expert advice. Health studies have shown that chemical exposure may cause potential human health risks which may vary from person to person.

Note :

Section 3. Composition/information on ingredients Substance/mixture :

Occupational exposure limits, if available, are listed in Section 8.

Mixture

There are no ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Get medical attention if irritation occurs.

Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical attention if symptoms occur.

Section 4. First aid measures

Eye contact

Inhalation :

Description of necessary first aid measures

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 1/10

MOBIL DTE 732

Section 4. First aid measures

Wash out mouth with water. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Do not induce vomiting unless directed to do so by medical personnel. Get medical attention if symptoms occur.

Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency.

Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.

Skin contact

Ingestion :

Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training.

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.

Specific treatments : No specific treatment.

Most important symptoms/effects, acute and delayed

Inhalation : No known significant effects or critical hazards.

No known significant effects or critical hazards.:Ingestion

Skin contact : No known significant effects or critical hazards.

No known significant effects or critical hazards.:Eye contact

Over-exposure signs/symptoms

Skin contact

Ingestion

Inhalation No specific data.

No specific data.

Local necrosis as evidenced by delayed onset of pain and tissue damage a few hours after injection.

Eye contact : No specific data.

Potential acute health effects

See toxicological information (Section 11)

Indication of immediate medical attention and special treatment needed, if necessary

Section 5. Fire-fighting measures

Use standard firefighting procedures and consider the hazards of other involved materials. Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. Assure an extended cooling down period to prevent re-ignition.

Prevent runoff from fire control or dilution from entering streams, sewers, or drinking water supply. No action shall be taken involving any personal risk or without suitable training.

Hazardous combustion products

Specific hazards arising from the chemical

In a fire or if heated, a pressure increase will occur and the container may burst.

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Special protective equipment for fire-fighters

Use dry chemical, CO₂, water spray (fog) or foam.

Extinguishing media

Do not use water jet.

Suitable extinguishing media

Unsuitable extinguishing media

Special protective actions for fire-fighters

Aldehydes, Incomplete combustion products, Oxides of carbon, Smoke, Fume, sulfur oxides

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 2/10

Section 6. Accidental release measures

Environmental precautions

Personal precautions, protective equipment and emergency procedures

Stop leak if without risk. Move containers from spill area. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Confine the spill immediately with booms. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist before using dispersants. Warn other shipping. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.

: No action shall be taken involving any personal risk or without suitable training.

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Put on appropriate personal protective equipment.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).

Large spill :

Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.

Small spill :

Methods and materials for containment and cleaning up

For non-emergency personnel

For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non-emergency personnel".

NOTIFICATION PROCEDURES

In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations. US regulations require reporting releases of this material to the environment which exceed the applicable reportable quantity or oil spills which could reach any waterway including intermittent dry creeks. The National Response Center can be reached at (800)424-8802.

Water spill and land spill recommendations are based on the most likely spill scenario for this material; however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local regulations may prescribe or limit action to be taken.

Section 7. Handling and storage

Advice on general occupational hygiene

Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.

Protective measures Put on appropriate personal protective equipment (see Section 8).:

Precautions for safe handling

Static Accumulator : This material is a static accumulator. A liquid is typically considered a nonconductive, static accumulator if its conductivity is below 100 pS/m (100x10E-12 Siemens per meter) and is considered a semiconductive, static accumulator if its conductivity is below 10,000 pS/m. Whether a liquid is nonconductive or semiconductive, the precautions are the same. A number of factors, for example liquid temperature, presence of contaminants, anti-static additives and filtration can greatly influence the conductivity of a liquid.

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 3/10

Section 7. Handling and storage Conditions for safe storage, including any incompatibilities

Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

severely hydrotreated heavy paraffinic distillate NIOSH REL (United States, 10/2020) [OIL MIST MINERAL] TWA 10 hours: 5 mg/m³. Form: Mist.

STEL 15 minutes: 10 mg/m³. Form: Mist.

OSHA PEL (United States, 5/2018) [Oil mist, mineral] TWA 8 hours: 5 mg/m³.

ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and severely refined] TWA 8 hours: 5 mg/m³. Form: Inhalable fraction.

Section 8. Exposure controls/personal protection

Ingredient name Exposure limits

Hand protection

Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary.

Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side-shields.

Eye/face protection

Respiratory protection :

Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Environmental exposure controls

: Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.

Appropriate engineering controls

: Good general ventilation should be sufficient to control worker exposure to airborne contaminants.

Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.

Hygiene measures :

Control parameters

Individual protection measures

Occupational exposure limits

Skin protection

Other skin protection : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

NOTE: Limits/standards shown for guidance only. Follow applicable regulations.

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 4/10

Section 9. Physical and chemical properties and safety characteristics

Physical state

Melting point/freezing point

Vapor pressure

Relative density

Relative vapor density

Solubility in water

Liquid.

Not available.

0.86

>2 [Air = 1]

<0.1 mm Hg [20 °C]

Negligible

CharacteristicOdor pH

AmberColor

Evaporation rate Not available.

Auto-ignition temperature

Flash point

Not available.

Open cup: >215°C (>419°F) [ASTM D-92]

>3.5

Not applicable.

Viscosity 31.5 cSt [40 °C] [ASTM D 445]

5.68 cSt [100 °C] [ASTM D 445]

Not available.Odor threshold

Partition coefficient: n-octanol/water

Appearance

Boiling point or initial boiling point and boiling range

: >315.56°C (>600°F)

Flammability : Ignitable

Lower and upper explosion limit/flammability limit

: Lower: 0.9% Upper: 7%

Decomposition temperature :

The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Note: Physical and chemical properties are provided for safety, health and environmental considerations only and may not fully represent product specifications. Contact the Supplier for additional information.

Not available.

DMSO Extract (mineral oil only), IP-346

: <3 % by weight

Pour point : -18°C

Particle characteristics

Median particle size : Not applicable.

Section 10. Stability and reactivity

Hazardous decomposition products

Conditions to avoid High energy sources of ignition. Excessive heat.

The product is stable.Chemical stability

Strong oxidizers

Incompatible materials :

Possibility of hazardous reactions

: Under normal conditions of storage and use, hazardous reactions will not occur.

Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Under normal conditions of storage and use, hazardous decomposition products should not be produced.

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 5/10

Section 11. Toxicological information

Acute toxicity

Inhalation : Minimally Toxic. No end point data for material. Based on assessment of the components.

Carcinogenicity

Conclusion/Summary : Not expected to cause cancer. No end point data for material. Based on assessment of the components.

Mutagenicity

Conclusion/Summary : Not expected to be a germ cell mutagen. No end point data for material. Based on assessment of the components.

Reproductive toxicity

Conclusion/Summary : Not expected to be a reproductive toxicant. No end point data for material. Based on assessment of the components.

Irritation/Corrosion

Conclusion/Summary

Skin : Negligible irritation to skin at ambient temperatures. No end point data for material.

Based on assessment of the components.

Eyes : May cause mild, short-lasting discomfort to eyes. No end point data for material. Based on assessment of the components.

Respiratory : Negligible hazard at ambient/normal handling temperatures. No end point data for material.

Respiratory or skin sensitization

Conclusion/Summary

Skin : Not expected to be a skin sensitizer. No end point data for material. Based on assessment of the components.

Respiratory : Not expected to be a respiratory sensitizer. No end point data for material.

Other information

: Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung non-specific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitizing in test animals.

Specific target organ toxicity (single exposure)

Specific target organ toxicity (repeated exposure)

Product/ingredient name Category

MOBIL DTE 732 Not applicable. -

Aspiration hazard

Target organs

Information on toxicological effects

Dermal : Minimally Toxic. No end point data for material. Based on assessment of the components.

Oral : Minimally Toxic. No end point data for material. Based on assessment of the components.

Conclusion/Summary

Conclusion/Summary : Not expected to cause organ damage from a single exposure. No end point data for material.

Conclusion/Summary : Not expected to cause organ damage from prolonged or repeated exposure. No end point data for material. Based on assessment of the components.

Conclusion/Summary : Not expected to be an aspiration hazard. Based on physico-chemical properties of the material. Data available.

Contains

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 6/10

Section 12. Ecological information

Mobility Base oil component -- Expected to partition to sediment and wastewater solids. Low solubility and floats and is expected to migrate from water to the land.

Bioaccumulative potential

Other adverse effects : No known significant effects or critical hazards.

Toxicity

Conclusion/Summary

: Not expected to be harmful to aquatic organisms.

Persistence and degradability

: Base oil component -- Expected to be inherently biodegradable

Mobility in soil

Acute toxicity

Chronic toxicity : Not expected to demonstrate chronic toxicity to aquatic organisms.

Biodegradability

Conclusion/Summary : Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may reduce the bioconcentration or limit bioavailability.

Other ecological information

The information given is based on data for the material, components of the material, or for similar materials, through the application of bridging principals.

Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction.

Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Empty Container Warning (where applicable): Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY

EXPLODE AND CAUSE INJURY OR DEATH.

:Disposal methods

Section 14. Transport information

Not regulated.

Not regulated. Not regulated.

DOT Classification

UN number

UN proper shipping name

Transport hazard class(es)

Packing group

Environmental hazards

No. No. No.

Not regulated.

No.

TDG Classification IMDG IATA

Label(s) / Marks

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 7/10

Section 14. Transport information Special precautions for user Transport within user’s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage.

Transport in bulk according to IMO instruments

: Not applicable.

Section 15. Regulatory information U.S. Federal regulations

The following components are listed: OIL MIST, MINERAL

TSCA 4(a) proposed test rules: 1h-benzotriazole, methyl-

Clean Water Act (CWA) 307: 1-methylnaphthalene; 2-methylnaphthalene; naphthalene;

ethyl benzene

Clean Water Act (CWA) 311: naphthalene; aniline; xylenes; potassium hydroxide; ethyl benzene; propylene oxide

Massachusetts

SARA 313

Clean Air Act Section 112

(b) Hazardous Air Pollutants (HAPs)

: Listed

Clean Air Act Section 602 Class I Substances

: Not listed

Clean Air Act Section 602 Class II Substances

: Not listed

DEA List I Chemicals (Precursor Chemicals)

: Not listed

DEA List II Chemicals (Essential Chemicals)

: Not listed

New York : None of the components are listed.

New Jersey : None of the components are listed.

Pennsylvania : None of the components are listed.

State regulations

TSCA 8(a) PAIR: 1-naphthylamine, n-phenyl-; diphenylamine; naphthalene; siloxanes and silicones, di-me

TSCA 8(a) CDR Exempt/Partial exemption: Not determined

SARA 302/304

SARA 304 RQ : 3360215053.8 lbs / 1525537634.4 kg [468609775.9 gal / 1773880970.2 L] aniline <0.1 Yes. 1000 117.6 5000 587.9 propylene oxide <0.1 Yes. 10000 1444.3 100 14.4 ethylene oxide <0.1 Yes. 1000 - 10 -

Composition/information on ingredients

Name % EHS (lbs) (lbs)(gallons) (gallons)

SARA 302 TPQ SARA 304 RQ

SARA 311/312

Classification : Not applicable.

This material contains no chemicals subject to the supplier notification requirements of the SARA 313 Toxic Release Program.

Illinois : None of the components are listed.

Not applicable.

TSCA 12(b) - Chemical export notification

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 8/10

Section 15. Regulatory information Inventory list

Australia inventory (AIIC) :

Canada inventory (DSL-NDSL) :

China inventory (IECSC) :

Japan inventory (CSCL) :

Korea inventory (KECI) :

New Zealand Inventory of Chemicals (NZIoC)

Philippines inventory (PICCS) :

Taiwan Chemical Substances Inventory

(TCSI)

United States inventory (TSCA 8b) :

Japan inventory (Industrial Safety and Health Act)

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are active or exempted.

Section 16. Other information

History

Date of issue/Date of revision

Version

Date of previous issue

16 July 2024

4 June 2024

1.02

Hazardous Material Information System (U.S.A.)

National Fire Protection Association (U.S.A.)

Health

Flammability

Physical hazards

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc.

The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Procedure used to derive the classification

Not classified.

severely hydrotreated heavy paraffinic distillate 64742-54-7 2,6-di-tert-butylphenol 128-39-2 solvent naphtha (petroleum), heavy arom. 64742-94-5 1-naphthylamine, n-phenyl- 90-30-2 alkarylamine 36878-20-3

New Jersey Right to Know Disclosure

Name CAS #

/ 0

0Health

Special hazards

Instability

Flammability

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 4 June 2024 Version : 1.02 9/10

Section 16. Other information

The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current available from ExxonMobil. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law, re-publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any affiliates in which they directly or indirectly hold any interest.

Notice to reader

Indicates information that has changed from previously issued version.

References : Not available.

Key to abbreviations : ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group UN = United Nations

Product code : 201560302015_1159467