MILC19516gAMEND1.pdf

lrNCH-POUNDI

MIL-C-19516G(MC)

AMENDMENT-1

MA.Y G 4 1982

MILITARY SPECIFICATION

COAT, MAN'S: POLYESTER/WOOL, GABARDINE; BLUE

This amendment forms a part of Military Specification MIL-C- 19516G(MC), dated 6 March 1991, and is available for use by all Departments and Agencies Of the Department of Defense.

3.3.5.1.1 - At the end of operation add the following:

"As an alternate, needle punch fabric in lieu of flannel is permitted " .

3.3.9, line 5 - after ''3/4'', add "to 1 inch wide''.

Line 6 after "be" delete ''l-1/8'' and add "1 to 1 1/8''.

3. 3 .15 .1. 2, line 4, - after "washer" add •, composite undercollar cloth, needle punch or felt, may be used".

Under Pattern Nomenclature, After "item 38", add the following:

"39. Left Front shaper".

AMSC N/A FSC' 8405

DISTRIBUTION STATEMENT A. Approved for public release;

distribution is unlimited.

AMENDMENT-1

Operation 1, paragraph E, 4th line - After number "3/4" add "to 1 inch wide".

Operation 18, last line - Delete ''6'' and substitute "8".

Operation 29a, line 2 - Delete "wool".

At end of operation 46i, add the following:

"or when the alternate fusible front is used the following operations for the floating chest piece are required:

Make floating chest piece (see figure 10).

a. Spread the shoulder dart on the haircloth stitch to wedge piece with edges overlapped.

piece pattern parts show spread of dart.

304 FSa-1 or LSa 4-8 70-2 chest piece and Notches on wedge

70-2

b. Abut or overlap 1/8 inch of the edge of the neckline and lower armhole darts on the haircloth chest piece and stitch together.

304 FSa-1 or LSa-1 4-8 70-2 70-2 c, Position the haircloth reinforcement piece at the top front corner on the underside of the chest piece. Place the polyester/cotton cloth covering for the front edge on top of the haircloth chest piece with front and neckline edges even.

Position the flannel/felt padding on the under side of chest piece and quilt together with vertical rows of stitching 3/8 to 3/4 inch apart and with curved rows toward the armhole. The padding shall extend beyond the armhole and the shoulder portion shall be left open to accommodate the shoulder pads.

304 4-8 70/2 70/2"

Operation 54b, ·· tine 16 c. After --"the" add ·"armhole"-.------ Line 17, delete "bottom" and substitute "armhole".

Operation 59, line 15 - After "for'' delete ''size 35 to 46" and substitute "all larger sizes''.

Operation 72d, line 7 - Delete ''55" and substitute ''56''.

Table IV, Test Methods under "Rqmt. Para." for "Material Identification'', delete "3.3.5" and substitute "3.3.6''. Under "Rqmt. Para" for "Weight - oz. per sq. yd.", delete "3.3.5" and substitute "3.3.6''. Under ''Rqmt Para.'' for ''Color", delete "3.3.5'' and substitute "3.3.6".

4.5.3, under ''Coat Size (S)'' above "30 - 33'' add "30 - 31''.

Second line delete "30 - 33'' and substitute ''32 - 33". Under "Form Size 11 above "30" add 11 28 11

Defect C 6, Line 3. - After "Pleat:" delete remainder of table and add the following new information:

----------- Examine--

AMENDMENT-1

- - Defect ---- ----

- more than 3/16 inch

- more than 1/4 inch

7 . Top edge of flap not positioned midway between second and third buttonholes + 3/16 inch.

Classification ·Major (*) - - Minor '

A B

NOTE: Pockets must be in horizontal alignment with each other as required.

8. Staypiece not tacked 336 or not securely tacked to interlining across top edge of front center

9. Polyester and cotton I 272 staypiece omitted on underside of one or both pockets.

10. Top edge of pocket less 337 than 3/8 inch or more than 5/8 inch below the top stitching of flap.

11. Top edge of flap 273 crooked.

d. Upper pockets.

1. Binding on top edge 274 omitted or not securely caught to fabric, causing binding to pull away from fabric.

2. One or both pocket 275 corners not securely tacked.

3. Pleat off center 1/4 131 inch or more at lower edge of flap.

4 . Pleat formed crookedly, 276 affecting appearance.

5 . Poorly shaped, not in 18 conformity with pocket shaper.

Examine

6.

7 .

8 .

9 .

10.

11.

12.

13.

14.

15.

MIL-C-19516G(MC)

AMENDMENT-1

Defect

Constructed with fold of pleat on the under-side.

Pleat less than 1-1/8 inches or more than 1-3/8 inches wide (sizes 30-35) .

Pleat less than 1-3/8 inches or more than 1-5/8 inches wide (sizes 36-46).

Front edge of pleat below flap not parallel with front edge of pocket by more than 3/16 inch.

Pleat not stitched closed.

Bottoms of pockets out of horizontal alignment by:

- 1/4 inch or more but not more than 3/8 inch.

- more than 3/8 inch.

Front edge of pocket not parallel with front edge of coat when buttoned by:

0 - 3/16 inch or more but not more than 1/4 inch.

- more than 1/4 inch.

Excessive fullness or tightness at pocket opening, affecting appearance.

Button and buttonhole not aligned, causing noticeable bulge or twist on pocket or flap when buttoned, affecting appearance.

lower corner of pocket not trimmed.

Classification Major ( *) Minor

A B

Classification --1------------------------- Major- (*) Minor ·· -

Examine Defect

e. Upper pockets and flaps measurements:

1. Length of flap (at center point), length of flap (at sides), width of pocket (at top edge, side to side edge), width of pocket (at bottom edge, side to side edge), length of pocket (top to bottom edge). Any of the above dimensions and tolerances included in Table III:

Exceeding the+ 1/8 inch 135 tolerance

f. Lower pocket flaps (position):

1.

2.

3.

Out of horizontal alignment by 3/16 inch but not more than 3/8 inch.

- more than 3/8 inch Flap not covering pocket opening:

- Front corner of 1 or both pockets.

- back corner of 1 pocket.

- back corner of both pockets.

Lower side edge of flap extending beyond or both edges of or both pockets by more than 3/16 inch.

A B

MIL-C-19516G(MC)

AMENDMENT-1

Defect

4. Front edge of flap out of vertical alignment with front edge of upper pocket 1/4 inch or more.

5. Lower side edge of flap (excluding rounded corners) not covering side edge of pocket by 1/8 inch or more but not more than 1/4 inch:

- front edge of 1 or both pockets.

- back edge of 1 or both pockets.

6. More than 1/4 inch:

- front edge of 1 or both pockets.

- back edge of 1 or both pockets.

7. Front edge of flaps not parallel with front edge of coat by 1/4 inch or more when coat is buttoned.

8. Polyester and cotton staypiece not tacked or not securely tacked interlining at front corner.

9. Polyester and cotton staypiece omitted on underside of 1 or both pockets.

10. Top edge of flap not parallel with the waist seam by 1/4 inch or more.

g. Lower pockets:

Classification Major~-~(*)~~~ Minor

A B

1.

2.

3.

4.

5.

6.

7.

8.

MIL-C-19516G(MC)

AMENDMENT-1

Defects

Binding on top edge omitted or not securely caught in fabric, causing binding to pull away from fabric.

One or both pocket corners not securely stitched.

Pockets poorly shaped, not in conformity with pocket shaper.

Distance between bottom edge of lower pocket and bottom edge of coat:

- less than 1 inch but not less than 3/4 inch.

- less than 3/4 inch.

Bottom edge of pocket not parallel with bottom edge of coat by:

- 1/4 inch or more but not more than 3/8 inch.

- more than 3/8 inch.

Bottoms of pockets out of horizontal alignment by:

- more than 1/4 inch but not more than 1/2 inch.

- more than 1/2 inch.

Excessive fullness or tightness at pocket opening, affecting appearance.

Diagonal position of pocket (front edge from directly below flap to bottom edge) with front edge of coat.

- parallel with front edge.

- slanted more than 3/8 inch from front

Classification Major ( *) Minor

A B

Shoulder (construc tion)

Shoulder pads

MIL-C-19516G(MC)

AMENDMENT-1

Defect edge (i.e., towards side seam).

Classification Major (*} Minor

A B

- slanted 1/8 inch or 141

9.

more towards front edge.

Button and buttonhole not aligned, causing noticeable bulge or twist on pocket or flap.

h. Lower pockets and flaps measurements:

1. Length of flap (at center point), length of flap (at sides), width of flap (at top edge, side to side edge), width of pocket at bottom edge, (side edge to side edge) length of pocket (top to bottom edge) for Short, Regular Long and X-Long.

Any of the above dimen sions varying from nom-inal dimensions and tol- 142 erances included in Table III: Exceeding the + 1/8 inch tolerance.

Improper joined or set, causing shoulders or back to twist.

a. Not completely caught in armhole tacking.

b. Misplaced, not serving intended purpose, i.e., too far back or too far forward.

c. One or both pads omitted.

Shoulder a, straps b.

c.

d.

e, f.

MIL-C-19516G(MC)

AMENDMENT-1

Defect

Misplaced, i .e If one strap further forward or back from position of other strap affecting appearance.

Strap stitched to coat too full or twisted, or stitched to coat too tight, causing fullness or twist on front or back of coat.

Poorly shaped.

Shoulder seam exposed beyond back edge of shoulder strap (except rounded end) .

Width of shoulder strap at armhole seam (including piping):

- less than 2-1/4 inches but not less than 2-1/8 inches.

- more than 2-1/2 inches but not more than 2-5/8 inches.

- less than 2-1/8 inches or more than 2-5/8 inches, Width of shoulder strap across center of insignia button (including piping):

- less than 1-1/2 inches but not less than 1-3/8 inches.

- more than 2 inches but not more than 2-1/8 inches.

- less than 1-3/8 inches or more than 2-1/8 inches.

Classification Major ( *) Minor

A B

201a

202a

203a

204a g.

h.

i.

j.

Armholes a.

(construe-tion) b.

c.

d.

e.

f.

g.

MIL-C-19516G(MC)

AMENDMENT-1

Defect

Rounded end of shoulder strap positioned less than 1/4 inch or more than 3/8 inch from collar edge.

Piping irregular in width, affecting appearance.

Buttons not uniformly set from collar edge by more than 1/4 inch.

Center of buttons les's than 3/4 inch or more than 7/8 inch from rounded end of strap (including piping).

Badly stretched.

Taped too tight, causing puckering around armhole seam, affecting appearance.

Crooked seam.

Tape stitching exposed and visible on outside surface.

Sleeve head pads not com-pletely tacked to armholes, or misplaced, not serving intended purpose.

One or both sleeve head pads omitted.

Armhole not tacked com-pletely or insecurely tacked.

Classification Major ( *) Minor

A B

205a

206a

207a

208a

209a

Sleeves a, b.

MIL-C-19516G(MC)

AMENDMENT-1

Defect

Setting and hang:

1. Sleeve fullness mis-placed, affecting appearance.

2. Sleeve too far front, i.e., front edge of sleeve less than 1 inch more than 2-1/2 inches from center point of lower pocket flap button.

3. Sleeve too far back, i, 8, / front edge of sleeve more than 1 to 2-1/2 inch back from center point of lower pocket flap button.

4 . Hang of sleeves in opposite directions,

i. e,, one sleeve too far forward and one sleeve too far back, tolerance of 1-1/2 inches.

5. Sleeves tight in arm hole, i • 8, / roll effect not present at front or back of sleeve.

Sleeve lining:

1. Twisted, tight or short, causing bulge, twist or puckering on outside of sleeves.

2. Sleeve lining too long, causing lining to sag at bottom more than 1/2 inch.

Classification Major ( *) Minor

A B

210a c.

d.

3.

MIL-C-19516G(MC)

AMENDMENT-1

Defects

Sleeve lining seams out of alignment more than 3/8 inch with sleeve seams at arm holes or at bottom of sleeves, Construction of sleeves:

1. Wigan twisted, tight, or pleated, causing ridges or puckering on outside of bottom of sleeves, affecting appearance.

2. Tacking on bottom turn-up to wigan omitted or insecure.

3. Sleeve bottom edge uneven by more than 1/4 inch.

4 . Tacking on 1 or both sleeve lining seams to sleeve seams omitted or insecure.

5 . Bottom edge of sleeve lining turnup less than 1 inch or more than 1-1/2 inches up from bottom edge of sleeve.

Ornamental sleeve pieces:

1. Piping irregular, affecting appearance.

2. Ornamental piece stitched to sleeve too full or twisted, affecting appearance.

3. Length of ornamental piece (including piping)

- less than 5-7/8 inches or more than 6-3/8 inches.

Classification Major ( *) Minor

A B

211a

212a

213a

214a e.

4 .

5 .

6 .

7.

8.

9.

MIL-C-19516G(MC)

AMENDMENT-1

Defect

Width at top, center, and bottom points (including piping):

- less than 2-3/8 inches or more than 2-7/8 inches.

Poorly shaped, affect-ing appearance.

Set on crookedly, affecting appearance.

Misplaced, i.e., one piece further forward or back from position of other piece, affecting appearance.

Bottom edge not horizontal with bottom edge of sleeve by more than 1/8 inch or edge extends beyond bottom edge of sleeve.

Ornamental piece stitch-ed to sleeve with pointed ends toward forearm seam of sleeve.

Position of buttons on ornamental pieces (measure-ments made from center of button):

1. From top and bottom edges (including piped edge):

- less than 3/4 inch but not less than 1/2 inch.

- more than 1 inch but not more than 1-1/4 inches.

- less than 1/2 inch or more than 1-1/4 inches.

Classification Major ( *) Minor

A B

215a

216a

217a

218a

219a

Body a.

(outside) b, 2.

3.

4 .

MIL-C-19516G(MC)

AMENDMENT-1

Defect

Top or bottom button from scalloped edge including piped edge:

- less than 5/8 inch but not less than 3/8 inch.

- less than 7/8 inch but not more than 1-1/8 inches,

- less than 3/8 inch or more than 1-1/8 inches.

Center button from pointed edge (including piped edge):

- less than 1-1/8 inches but not less than l inch or more than 1-3/8 inches but not more than 1-1/2 inches.

- less than 1 inch or more than 1-1/2 inches.

Center button not in line with pointed edge by:

- more than 1/4 inch.

Fitting of body and yoke linings: Tight, short, or twisted, causing fullness or twist on outside of coat, affecting appearance.

Fitting of f·ront inter-lining:

1. Tight, short, or twisted, causing full-ness or twist on out-side of coat, affecting appearance.

2. Too full, causing coat front to have a wavy appearance.

Classification Major ( *) Minor

A B

220a

221a

222a

AMENDMENT-1

Defect

Waist seam a. Seam not pressed open.

b. Seam stretched, affecting appearance.

c. Tape set on tight, causing puckering on waist seam, affecting appearance.

Chest Darts a. One or more omitted.

b. Upper fold of 1 or more darts not facing toward front edge of coat.

c. One or more not extending below breast flap.

Waist dart a. Waist dart not pressed and side open.

panel

Front and bottom edge

b. Side panel seam not pressed open.

a. Front edges stretched, affecting appearance.

b. Tape or piping set on tight, causing puckering on front, affecting appearance.

c. Front or bottom piping irregular, affecting appearance. Piping shall be no more than 1/8 inch wide nor less than 1/16 inch wide.

d, Bottom edge stretched, puckering, or uneven, affecting appearance.

Classification Major (*) Minor

226a

227a

228a

229a

230a

231a

A B

223a

224a

225a

Front facings

Back side panel seam

Vent opening

MIL-C-19516G(MC)

AMENDMENT-I

Defect

e. Bottom corner of left front poorly shaped, affecting appearance.

f. Left front rolling outward below bottom button.

g. Front edge irregular, affecting appearance.

h. Left forepart overlapping right forepart at bottom.

To measure the coat lying flat, match the side seams with the bottoms even. The right shall be 3-1/2 + 1/4 inches from the outer finished edge of left front.

i. Piping tight on front or bottom edge, causing puckering outside of coat, affecting appearance.

Short, tight, or twisted, causing fullness or twists on fronts, affecting appearance.

a. Not pressed open.

b. Curved panel seam on back of coat stretched or distorted, affecting appearance.

a. Left vent edge stretched, causing vents to spread open, affecting appearance.

b. Row of stitching across top of vent opening omitted or insecure or not caught through vent lining.

Classification Major (*) Minor

A B

232a

233a

234a

235a

236a

237a

238a

AMENDMENT-1

Defect

c. Left vent 1/4 inch or more shorter than right vent,

d. Left vent 1/4 inch or more longer than right vent.

e. Tape on left edge set on tight, causing puckering on vent edge, affecting appearance.

f. Left vent edge crooked, affecting appearance.

g. Left vent backpart over lapping right vent back part at bottom edge:

- less than 3-1/4 inches or more than 3-3/4 inches.

h. Width of left vent measured at bottom piped edge:

- less than 1-7/8 inches or more than 2-1/8 inches wide.

i, Row of stitching across top of vent opening less than 1-5/8 inches or more than 2 inches long.

j. Piping exposed and visible on left vent edge.

k. Row of stitching across top of vent opening mis placed, not serving intended purpose.

Classification Major (*) Minor

A B

239a

240a

241a

242a

4,5.3.4 Detailed defects of inside of coat /with coat spread on table), Detailed defects of inside of coat (with coat spread on table) shall be classified as follows:

Examine Defect

Front a, Position from front edge buttonholes (including piped edge):

Front buttons (positioned and secure sewing)

- less than 1/2 inch or more than 3/4 inch. (sizes 36-46.)

- less than 3/8 inch or more than 5/8 inch. ( sizes 30 - 35. )

b. More than 1/4 inch from equal spacing.

c. Bottom buttonhole above or below waist seam.

d, Top buttonhole less than 3/4 inch or more than 1 inch from top edge of piping, e, Unevenly spaced from front edge by more than 3/16 inch.

a. Out of vertical alignment by 1/4 inch or more.

b. Center of buttons more than 3/8 inch off-center midway between front edge of upper pockets when buttoned.

c. Button stitching caught through interlining (canvas front) but not facing:

- on 1 button.

- on 2 or more buttons.

d. Button stitching not caught through interlining (canvas front) on 1 or more buttons.

Classification Major (*) Minor

A B

243a

244a

245a

246a

247a

248a

249a

250a

251a

Examine Defect

Belt loops a. Loops less than 3/8 inch or more than 5/8 inch wide.

Labels

b. Length of belt loop from top to bottom folded edge:

- less than 2-3/8 inches or more than 2-5/8 inches.

c. One or both belt loops placed less than 1/8 inch or more than 5/8 inch from back end of lower pocket flap(s).

d. Bottom folded end of loop more than 1/4 inch above top edge of lower flap.

e. Bottom end of loop bartack ed through double fold exposing bartack.

f. Omitted:

- 2 loops.

- 1 loop.

g. Loops not perpendicular by:

- more than 1/4 inch but not more than 1/2 inch.

- more than 1/2 inch.

h. Top folded end of loop bar tacked to forepart less than 1/8 inch or more than 1/4 inch from folded end.

a. Any required label missing, incorrect, illegible or size label not securely caught in stitching.

Classification Major (*) Minor

A B

252a

253a

254a

Hanger

Front facing

Back yoke lining

MIL-C-19516G(MC)

AMENDMENT-1

Defect b, Woven instruction or identification label not stitched on 4 sides or not positioned as specified to the outside of right facing.

a. Hanger omitted or ends not securely stitched.

b. Less than 1-7/8 inches or more than 2-1/8 inches long measured along collar seam.

c. Hanger not stitched to neck of coat prior to seaming collar to neck of coat.

a. Fullness or pleats on facings between buttons, buttonholes or between front edge and buttons or buttonholes when buttoned.

b. Tacking on back edge to 1 or both interlinings:

- omitted,

- insecure or incomplete for a distance of more than 5 inches below shoulder seams, or more than 4 inches above bottom edge of lining.

c. Tacking at back lower edge of facing caught through l or both pockets.

d. Tacking at back edge of 1 or both facings from bottom edge across scarlet piping omitted or insecure.

a. Excessive fullness or pleats.

Classification Major (*) Minor

A B

255a

256a

257a

Front body linings

MIL-C-19516G(MC)

AMENDMENT-1

Defect b, Twisted, not affecting smoothness on outside surface of back.

c. Hem twisted, or width less than 1/4 inch or more than 1/2 inch wide.

d. Bottom raw edge of yoke not turned under in stitching forming hem.

e. Pleat in center of yoke lining omitted.

f. Folded edge of center pleat facing the right side of coat.

g. Felling at lower edge of yoke lining to side seam outlet omitted or insecurely felled on one or both sides.

a. Excessive puckering or pleated.

b. Twisted, not affecting smoothness on outside of coat.

c. One or both chest pleats on shoulder omitted.

d. Folded edge of 1 or both chest pleats facing toward the shoulder.

Classification Major (*) Minor

A B

258a

259a

AMENDMENT-1

Defect

e. Felling on 1 or more front or back lower corners of forepart lining omitted or insecurely felled to facings or forepart side seam allowance.

f. Back stitch at lower arm hole edge from approximately 1-1/2 inches to front of forearm sleeve lining seam to side seam of body lining omitted.

g. Hem twisted, or width less than 1/4 inch or more than 1/2 inch wide.

h. Bottom raw edge of body lining not turned under in stitching forming hem.

Waist seam Tape on 1 or both waist seams omitted.

Collar lining and eyelet covers

a. Collar lining tab left end of collar omitted or extending beyond collar end for a distance of less than 3/4 inch.

b. Stitching on end, side edges, or across width of collar tab omitted,

c. Ends of collar lining not securely tacked.

d. 1 or both eyelet covers omitted.

e. 1 or both eyelet covers not covering eyelet.

Classification Major (*) Minor

A B

260a

261a

262a

263a

264a

265a

Right vent lining

Binding on seam out lets

MIL-C-19516G(MC)

AMENDMENT-I

Defect

f. Width of collar eyelet covers less than 1-5/8 inches or more than 1-7/8 inches.

g. Felling on front edge and along lower corner of 1 or both eyelet covers omitted.

h. Felling along lower corner of 1 or both eyelet covers extending for a distance of more than 3/4 inch.

i. Hand felling of lining across the full width at the left or right end of collar omitted.

a. Top edge not completely covering edges of center back seam outlets.

b. Felling at corners of vent openings omitted or insecure.

c. Folded edge of lining not extending beyond center seam allowance of right backpart.

d. Tight, short, or twisted, causing frillness or twist outside of coat.

a. Not securely caught on fabric, causing binding to pull away from fabric easily.

b. Binding tight, causing edge of seams to curl and not lie flat.

Classification Major (*) Minor

A B

398a

266a

399a

267a

268a

269a

?70a

271a

301a

Custodian:

Navy-MC

MIL-C-19516G(MC)

AMENDMENT-1

Preparing Activity:

DLA - CT

Project No. 8405-N177

MIL-C-19516G

(Amendment 1)

Front Covering (Poly/Cotton) Corner Reinforcement

(Hair Cloth)

Basic Fabric (Hair Cloth

Flannel or Felt

INSIDE FRONT OUTSIDE FRONT

ALTERNATE FLOATING CHEST PIECE

FOR FUSED FRONT, COAT, DRESS BLUE,

MAN'S MARINE CORPS

FIGURE 10

COAT, MAN'S: POLYESTER/WOOL, GABARDINE BLUE

Page 26 of 26 Pages

Basic Fabric (Hair Cloth)

STANDARD!( TION DOCUMENT IMPROVE'. :NT PROPOSAL

INSTRUCTIONS

1. The preparing activity must complete blocks 1, 2, 3, and 8 In block 1, both the document number and revision letter should be given.

2. The submitter of this form must complete blocks 4, 5, 6, and 7.

3. The preparing activity must provide a reply within 30 days from receipt of the form.

NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current contracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements.

3, DOCUMENT TITLE

1. DOCUMENT NUMBER

MIL-C-19516G

Coat, Man's: Polyester/Wool, Gabardine Blue

2, DOCUMENT DATE (YYMMDD)

92-05-04

4. NATURE OF CHANGE (Identify paragraph number and include propo!.ed rewrite, if pos.sible. Attach extra sheets as needed.)

5, REASON FOR RECOMMENDATION

6.

a,:

8, PREPARING ACTIVITY

a. NAME

DLA-CT

c. ADDRESS (Include Zip Code)

2800 South 20th Street Philadelphia, PA 19101-8419

DD Form 1426, OCT 89

b. THE PHONE (Include Area Code)

(1) Commercial

(215)737-8102

(1) AUTOVON

444-8102

If YOU DO NOT RECEIVE A REPLY WITHIN 45 OAYS, CONTACT:

Defense Quality and Standardization Office 5203 Lee~burg P1k.e, Suite 1403, fdlls Church, VA 22041-3Q66

Telephone (703) 756-2340 AUTOVON 289-2340

Prewous editions are obsolete. '98.}10