IRPOD_2026.pdf

05/26/2026

ITEM NAMENATIONAL STOCK NUMBER

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY

1H 5330-01-325-3506 X3 GSKT MATL SH,NPRN 20240222112329

AMERICAN SOCIETY FOR TESTING AND MATERIA ASTM-D1056/24X24X0.125 A

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 1RPTR01A

9A589102020140

TECHNICAL CONTACT

1.0 SCOPE

ADDITIONAL IDENTIFYING INFORMATION:

THE SUBJECT SHEET GASKET MATERIAL IS SIMILAR TO AMERICAN NATIONAL

RUBBER COMPANY P/N ANR4219-N.

THIS IRPOD PROVIDES THE REQUIREMENTS FOR A REPAIR PART CONSISTING

OF ONE PIECE.

2.0 LIST OF APPLICABLE DOCUMENTS

IF A SUPPLIER QUOTES TO A LATER REVISION OF THE DRAWING (OR CATALOG ITEM) THAN

SPECIFIED BELOW, SUBMITTAL OF QUOTE SHALL INCLUDE TWO (2) COPIES OF THE REVISED

DOCUMENT AND AN EVALUATION OF THE INTERCHANGEABILITY. THE FOLLOWING DOCUMENTS AND

CHANGE DATA ARE APPLICABLE TO THE EXTENT SPECIFIED IN THIS IRPOD, THE DRAWINGS, OR

OTHER DOCUMENTS INVOKED BY THIS IRPOD. CONTRACTING AGENCY APPROVAL IS REQUIRED TO

USE EARLIER SPECIFICATION VERSIONS THAN THOSE LISTED HEREIN, EXCEPT AS IDENTIFIED

BELOW. IF NO DOCUMENT VERSION IS LISTED, THEN ANY VERSION OF THE DOCUMENT MAY BE

USED.

RAW MATERIAL REQUIRED HEREIN MAY HAVE BEEN PROCESSED OR TESTED (FOR EXAMPLE, HEAT

TREATED OR ULTRASONICALLY TESTED) AS REQUIRED BY THE RAW MATERIAL SPECIFICATION

PRIOR TO RECEIPT OF THIS ORDER USING PREVIOUS VERSIONS OF PROCESSING OR TESTING

SPECIFICATIONS. THIS PROCESSING AND TESTING NEED NOT BE REPEATED IF:

1.IT COMPLIED WITH THE APPLICABLE REQUIREMENTS OF THE

PROCESSING/TESTING SPECIFICATION VERSIONS IN EFFECT AT THE TIME OF

THE ACTUAL PROCESSING OR TESTING AND;

2.ALL REQUIREMENTS OF THE RAW MATERIAL SPECIFICATION VERSION LISTED

HEREIN HAVE BEEN SATISFIED.

SECTION 6.0 IDENTIFIES SPECIAL REQUIREMENTS FOR SUBMITTAL OF THE PROCEDURES USED

FOR COMPLETED PROCESSING AND TESTING. ALL PROCESSING AND TESTING PERFORMED AFTER

RECEIPT OF THIS ORDER SHALL CONFORM TO THE PROCESSING/TESTING SPECIFICATION

VERSIONS LISTED HEREIN.

DOCUMENT NUMBER VERSION TITLE

MILITARY STANDARDS

MIL-STD-129 R AND R (CH. 2) MARKING FOR SHIPMENT AND STORAGE

OTHERS

ASTM D 1056 85 SPECIFICATION FOR FLEXIBLE CELLULAR

MATERIALS-SPONGE OR EXPANDED RUBBER

3.0 TECHNICAL REQUIREMENTS

3.1 MATERIAL REQUIREMENTS

GSKT MATL SH,NPRN ASTM-D1056/24X24X0.125

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY

1H 5330-01-325-3506 X3 GSKT MATL SH,NPRN 20240222112329

AMERICAN SOCIETY FOR TESTING AND MATERIA ASTM-D1056/24X24X0.125 A

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 2RPTR01A

9A589102020140

TECHNICAL CONTACT

THE SUBJECT GASKET SHALL BE OF NEOPRENE CELLULAR SPONGE MATERIAL,MID-DENSITY SCE

42 IN ACCORDANCE WITH SPECIFICATION ASTM-D-1056TY. 2, CL. C, GR 2.DIMENSIONAL

TOLERANCES SHALL BE +/- 1/16 INCH FOR THE THICKNESS AND +/- 3/4 INCH FOR THE

LENGTH AND WIDTH DIMENSIONS IN ACCORDANCE WITH ASTM D1056 FOR EXPANDED RUBBERS.

THE SHEET MATERIAL SHALL BE SUPPLIED WITH A PRESSURE SENSITIVE

ADHESIVE BACKING ON ONE SIDE.

THE SHEET MATERIAL SHALL BE 24 INCHES IN WIDTH, 24 INCHES IN

LENGTH AND 0.125 INCH THICK.

SHELF LIFE OF THIS ITEM IS THIRTY-SIX MONTHS.

THIS ITEM SHALL BE SUPPLIED WITH AT LEAST 85 PERCENT OF ITS

SHELF LIFE REMAINING AT TIME OF SHIPMENT.

3.2 MANUFACTURING AND PROCESS REQUIREMENTS

GSKT MATL SH,NPRN ASTM-D1056/24X24X0.125

CLEANLINESS REQUIREMENTS:

PART(S) SHALL BE CLEANED BY ANY PROCESS OR COMBINATION OF

PROCESSES WHICH WILL ACCOMPLISH THOROUGH CLEANING WITHOUT

DAMAGE TO THE PART(S). SURFACES SHALL BE EXAMINED VISUALLY

TO DETERMINE FREEDOM FROM DIRT, CORROSION, OIL, GREASE OR

FOREIGN RESIDUE. PRESERVATIVES SHALL NOT BE USED ON PART(S)

WHICH ARE VULNERABLE TO DAMAGE BY CONTACT PRESERVATIVES.

MERCURY CONTAMINATION:THIS ITEM SHALL NOT CONTAIN AND SHALL NOT BE CONTAMINATED BY

MERCURY OR MERCURY COMPOUNDS. THIS REQUIREMENT MUST BE PASSED ON TO ALL

SUBCONTRACTORS. (FOR PROCURING ACTIVITY USE ONLY,INCLUDE MERCURY CONTROL CLAUSE

FROM NAVSEAINST 5100.3 (SERIES)).

4.0 QUALITY ASSURANCE PROVISIONS

INTENTIONALLY LEFT BLANK

5.0 PREPARATION FOR DELIVERY

GSKT MATL SH,NPRN ASTM-D1056/24X24X0.125

MARKING REQUIREMENTS:

MARKING AND LABELING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

BAR CODE MARKING SUITABLE FOR HAND SCANNING IS REQUIRED.

IN ADDITION TO THE STANDARD MARKING REQUIREMENTS OF MIL-STD-129,

THE SELLER SHALL INCLUDE THE MANUFACTURER'S COMMERCIAL AND

GOVERNMENT ENTITY (CAGE) CODE AND THE MANUFACTURER'S REFERENCE/

PART NUMBER (MFR/PN) ON INTERMEDIATE AND UNIT PACKS.

MODIFY MARKINGS IN MIL-STD-129 TO INCLUDE:

A. TYPE I SHELF LIFE ITEM

B. CURE DATE

C. EXPIRATION DATE

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY

1H 5330-01-325-3506 X3 GSKT MATL SH,NPRN 20240222112329

AMERICAN SOCIETY FOR TESTING AND MATERIA ASTM-D1056/24X24X0.125 A

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 3RPTR01A

9A589102020140

TECHNICAL CONTACT

PACKAGING AND PACKING REQUIREMENTS:PACKAGING CODES FOR MIL-STD-2073-1 SHALL BE AS

SPECIFIED ELSEWHERE IN THE CONTRACT.

IN ADDITION TO THE EXISTING REQUIREMENTS OF MIL-STD-129, THIS PART SHALL CONTAIN

BAR CODES THAT IDENTIFY SHELF LIFE INFORMATION (CURE DATE, SHELF LIFE CODE) ON THE

UNIT PACKING ONLY.

6.0 CONTRACT DATA REQUIREMENTS

INTENTIONALLY LEFT BLANK

6.1 PROCEDURES AND REPORTS

INTENTIONALLY LEFT BLANK

6.2 OTHER CONTRACT DATA REQUIREMENTS

INTENTIONALLY LEFT BLANK