IFB 276154 Heavy Equipment.pdf

PDF 139 KB Posted

Attached to
Furnish and Deliver Heavy Equipment
Solicitation number
B27000694
Issued by
Hawaii County, Hawaii

About this file

This is an Invitation for Bids (IFB) issued by the University of Hawaii at Hilo, Board of Regents, for the furnishing and delivery of heavy equipment to support the Center for Maunakea Stewardship. The solicitation requires bidders to supply four separate pieces of new equipment: one backhoe loader (CAT420, Case 590 SN, John Deere 410P, or acceptable alternate), one front-end loader (CAT926, Komatsu WA380, Case 721G, John Deere 524P, or acceptable alternate), one road grader (John Deere 872P, CAT 150, Komatsu GD655-7, or acceptable alternate), and one skid steer sweeper (CAT 272D, Kubota SSV75, Case SV340B, or acceptable alternate). All equipment must be new with a model year of 2026 or later and meet detailed mandatory technical specifications including engine requirements, hydraulic systems, safety features, and operator amenities. Electronic bids must be submitted through Hawaii's electronic procurement system (HIePRO) no later than 2:30 p.m. on November 25, 2026. Questions and clarifications must be submitted through HIePRO by November 9, 2026 at 4:00 p.m. Hawaii Standard Time, with responses posted on November 18, 2026. Delivery of all equipment must occur within 120 consecutive calendar days from the Notice to Proceed, with delivery to Hale Pohaku at 44-374 Maunakea Access Road, Maunakea State Park, Hawaii 96720.

Award will be made to the lowest responsive and responsible bidder on each individual item. All equipment must be fully fueled and operational upon delivery with on-site driver orientation provided by the contractor. Each item includes a 36-month or 3,000-hour warranty, during which the contractor must replace or repair defective equipment at no cost to the University, provided defects are not due to abuse or negligence. Bidders must be the manufacturer or an authorized reseller and must provide manufacturer documentation of authorization. Technical data and manufacturer literature must be submitted in duplicate with bids. Damaged or defective equipment will be rejected and replaced at no additional cost to the University. Invoices for payment should be submitted to the Office of Contracts, Procurements and Payments at University of Hawaii at Hilo within 30 calendar days following receipt or acceptance of goods. Both out-of-state and Hawaii bidders are advised that bids are subject to general excise tax under Hawaii Revised Statutes Chapter 237 and use tax under Chapter 238, and no adjustments to bid prices will be allowed for these taxes.

View the file

Other files

File Type Posted
IFB 276154 Heavy Equipment MBF.pdf PDF

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

INVITATION FOR BIDS (IFB) NO. 27-6154

TO

FURNISH AND DELIVER HEAVY EQUIPMENT

FOR

CENTER FOR MAUNAKEA STEWARDSHIP

UNIVERSITY OF HAWAII AT HILO

UNIVERSITY OF HAWAII

HILO, HAWAII

OCTOBER, 2026

BOARD OF REGENTS

HONOLULU, HAWAII

IFB NO. 27-6154

P a g e | 1

TABLE OF CONTENTS

IFB No. 27-6154 to Furnish and Deliver Heavy Equipment for Center for Maunakea Stewardship, University of Hawaii at Hilo, University of Hawaii, Hilo, Hawaii

Section Pages

Notice to Bidders………………………………………………………………………... 2

Bid Requirements………………………………………………………………………. 3 – 4

Technical Specifications……………………………………………………………….. 5 – 11

Special Provisions………………………………………………………………………. 12 – 14

ATTACHMENT - Mandatory Bid Form……………………………………………….. 1 – 6

IT IS THE RESPONSIBILITY OF ALL BIDDERS TO CHECK THE TABLE OF CONTENTS

TO CONFIRM THAT ALL PAGES LISTED THEREIN ARE REVIEWED AND THAT THE

MANDATORY BID FORM IS SUBMITTED AS PART OF THEIR BID PACKAGE.

P a g e | 2

NOTICE TO BIDDER

NOTICE TO BIDDERS

The University of Hawaii IFB No. 27-6154, to Furnish and Deliver Heavy Equipment for Center for Maunakea Stewardship, University of Hawaii at Hilo, University of Hawaii, Hilo, Hawaii is issued and will be awarded through the State of Hawaii’s electronic procurement system (HIePRO). All bid responses must be submitted electronically through HIePRO no later than 2:30 p.m., November 25, 2026. Bids received after the due date and time or received in a form other than electronically through HIePRO will not be considered.

Bidders are advised that they should not wait until the last minute to submit their bid through HIePRO. Bidders are solely responsible for ensuring that their electronic submission through HIePRO is complete and all necessary files (Mandatory Bid Form) are attached to their bid prior to the IFB due date and time. The University shall not be responsible for any delay or failure of any Bidder to submit any materials updated through the IFB process on a timely basis.

Electronic Procurement Bidders interested in responding to this electronic solicitation must be registered on HIePRO.

To register, visit the following link:

https://hiepro.ehawaii.gov/videos/video/vendor_registration.html. Reference the Vendor Quick Reference Guide for additional information at https://hiepro.ehawaii.gov/static-resources/VendorQuickReferenceGuide.pdf.

HIePRO will be the system of record for the issuance of the IFB, to receive the Mandatory Bid Form and other Bid requirements, issue Amendments, and make award for the IFB.

Amendments and other information and materials provided through HIePRO, may include additions or changes with respect to the due date and time.

Special instructions in HIePRO related to this solicitation are incorporated herein and made a part of this IFB through reference. Bidders shall review all special instructions located in HIePRO.

Questions and Clarifications All questions and requests for clarifications must be submitted electronically through HIePRO.

Questions must be submitted by November 9, 2026 at 4:00 p.m., Hawaii Standard Time.

Responses will be posted on November 18, 2026. The University may refuse to answer any questions received outside of HIePRO or after the Questions/Answers deadline.

Luis Salaveria Chief Procurement Officer University of Hawaii

Posting Date: October 30, 2026

Vendors are responsible for notifying the Procurement Specialist Trisha Shibuya (e-mail: tnishino@hawaii.edu) for accessibility concerns related to this IFB.

P a g e | 3

BID REQUIREMENTS

FURNISH AND DELIVER HEAVY EQUIPMENT

FOR

CENTER FOR MAUNAKEA STEWARDSHIP

UNIVERSITY OF HAWAII AT HILO

HILO, HAWAII

By attaching The Mandatory Bid Form to HIePRO, the bidder has carefully examined the

INVITATION FOR BIDS (IFB) NO. 27-6154, TO FURNISH AND DELIVER HEAVY

EQUIPMENT FOR CENTER FOR MAUNAKEA STEWARDSHIP, UNIVERSITY OF HAWAII

AT HILO, UNIVERSITY OF HAWAII, HILO, HAWAII, and offers to furnish and deliver the heavy equipment for Center for Maunakea Stewardship, University of Hawaii at Hilo, as required by the University in strict accordance with the true intent and meaning of the Invitation for Bids (IFB), and shall complete delivery within ONE HUNDRED TWENTY (120) consecutive calendar days from the date designated in the Notice to Proceed, as follows:

TAX LIABILITY

Both out-of-state and Hawaii bidders are advised that the amount bid on this solicitation is subject to the general excise tax imposed by Chapter 237, Hawaii Revised Statutes (HRS) and, if tangible property is being imported into the State of Hawaii for resale, the use tax (currently 1/2%) imposed by Chapter 238, HRS. (Refer to Taxes in the General Provisions.)

Bidders are therefore cautioned to consider such taxes in formulating their bids since no adjustments to the prices bid shall be allowed.

BASIS FOR AWARD

The award of contract, if awarded, shall be made to the lowest responsive and responsible bidder on EACH ITEM.

P a g e | 4

NOTE TO BIDDERS

An acceptable bid must conform in all material respects to this Invitation for Bids. Any of the following may be grounds for disqualification:

1. Taking exception to any of the specifications, terms or conditions contained in the IFB.

2. Placing conditions on the furnishing of solicited goods or services.

3. Inclusion of a quotation or order form containing additional specifications, terms or conditions.

4. Referencing external documents containing additional specifications, terms or conditions.

Bidders are advised that bids are evaluated as submitted and requests by bidders to delete conditions contained in their bids after bid opening cannot be considered.

P a g e | 5

TECHNICAL SPECIFICATIONS

This section indicates the Technical Specifications for the heavy equipment. The Technical Specifications listed herein are the minimum requirements and are mandatory for an accepted bid.

Item No. 1 - Furnish and Deliver ONE (1) New, Backhoe Loader, CAT420, Case 590 SN, John Deere 410P, or acceptable alternate, with the following specifications:

Category Mandatory Specifications

Condition & Year New, 2026 or later

Type Four Wheel Drive or All Wheel Drive Backhoe Loader

Engine Diesel 4 Stroke Turbo Charged, Minimum 100hp

Fuel System Direct High Pressure Fuel Injection

Drive Train 1-4 Speed Forward and Reverse

Cabin ROPS/FOPS Cab

Steering Hydraulic Power Steering

Bucket 4 in 1 Bucket, Minimum 1 yd3

Backhoe Bucket Universal Bucket, Minimum 3.4 ft3

Gauges and Alarms

Engine Water Temperature Converter Oil Temperature Fuel Level Tachometer Hour Meter Engine Oil Pressure Parking Brake Engagement Low Fuel Back Up Alarm

Lights

Back Up Light LED Stop and Tail Light LED Turn Signal Lamps: Two (2) Front and Two (2) Rear with Hazard

Switch Working Lights Halogen: Two (2) Front Cab Mount

Mirrors

Rear View Mirrors: Two (2) Inside, Two (2) Outside

P a g e | 6

Operator Environment

Tilt Steering Wheel Mechanical Suspension Seat with 180-degree Swivel Retractable Seat Belt Closed Cabin with Hearting and AC Defroster

Operating Conditions

Must maintain full operating capacity up to 10,000 feet above sea level without power derating, and shall not exceed more than 10 percent power derating at 14,000 feet above sea level

Keys and Manual Three (3) Sets of Original Keys Two (2) Operator and Service Manuals in hard copy and One (1)

Operator and Service Manual in digital format (pdf)

Delivery Fully fueled and operational with on-site driver’s orientation for safe operation and maintenance upon delivery

Warranty 36 months or 3,000 hours

Item No. 2 - Furnish and Deliver ONE (1) New, Front-End Loader, CAT926, Komatsu WA380, Case 721G, John Deere 524P, or acceptable alternate, with the following specifications:

Type Four Wheel Drive Front-End Loader

Engine 4 or 6 Cylinder Diesel, Minimum 150hp

Aspiration Turbocharged After-cooled or Air-cooled

Drive Train 1-4 Speed Forward and Reverse

Cabin ROPS/FOPS Cab Level 2

Steering Hydraulic Power Steering

Brakes

Service Brakes:

Hydraulically Activated Wet Disc Brakes Actuate on Four (4) Wheels

Parking Brake:

Wet Disc Brake

Bucket Minimum 3.5 yd3

P a g e | 7

Air Conditioning and Heating

Manufacturer’s Standard

Gauges and Alarms

Engine Coolant Temperature Fuel Level Speed Transmission Shift Indicator Engine Tachometer Oil Temperature Parking Brake Reverse Alarm

Lights

Back Up Light LED Stop and Tail Light LED Turn Signal Lamps: Two (2) Front and Two (2) Rear with Hazard

Switch Working Lights Halogen: Two (2) Front Cab Mount, Two (2) Front

Fender Mount, Two (2) Rear Grill Mount

Mirrors

Rear View Mirrors: Two (2) Inside, Two (2) Outside

Operator Environment

Telescopic Steering Wheel Center Rear View Mirror Two (2) Side Rear View Mirrors Rear Defroster Retractable Seat Belt Windshield Wiper Rear View LCD Monitoring System

Operating Conditions

Must maintain full operating capacity up to 10,000 feet above sea level without power derating, and shall not exceed more than 10 percent power derating at 14,000 feet above sea level

Keys and Manual Three (3) Sets of Original Keys Two (2) Operator and Service Manuals in hard copy and One (1)

Operator and Service Manual in digital format (pdf)

Delivery Fully fueled and operational with on-site driver’s orientation for safe

P a g e | 8

Item No. 3 - Furnish and Deliver ONE (1) New, Road Grader, John Deere 872P, CAT 150, Komatsu GD655-7, or acceptable alternate, with the following specifications:

Type All Wheel Drive Motor Grader

Mainframe Welded Box Construction

Engine 6 Cylinder Diesel, Minimum 240hp

Aspiration Turbocharged Fuel Injection

Drive Train 1-7 Speed Forward and Reverse

Cabin Low Profile Cab with ROPS (ISO 3471-2008) and FOPS Cab

(ISO3449-2005)

Front Axle Minimum 30-degree oscillation, and minimum 20-degree wheel lean angle

Steering Hydraulic Power Steering

Brakes

Foot-controlled Hydraulically Operated Effective on all Four (4) Tandem Wheels

Parking Brake:

Automatically Spring Applied Hydraulically Released Oil Cooled Self-Adjusting

Moldboard Minimum 14-foot Blade

Circle 60-inch Diameter 360-degree Rotation

Rear Ripper/Scarifier Minimum 7-foot Width Maximum Depth 16-inch (Ripper)/12-inch (Scarifier)

Air Conditioning and Heating

Manufacturer’s Standard

P a g e | 9

Gauges and Alarms

Engine Coolant Temperature Fuel Level Speed Transmission Shift Indicator Engine Tachometer Oil Temperature Parking Brake Reverse Alarm

Lights Two (2)-High and Two (2)-Low Driving Halogen Headlights Front and Rear LED Turn Signals and Marker Lights LED Brake and Hazard Light

Mirrors One (1) Center Rear View Mirror

Operator Environment

Telescopic Steering Wheel Center Rear View Mirror Two (2) Side Rear View Mirrors Fan Defroster Retractable Seat Belt

Operating Conditions

Must maintain full operating capacity up to 10,000 feet above sea level without power derating, and shall not exceed more than 10 percent power derating at 14,000 feet above sea level

Keys and Manual Three (3) Sets of Original Keys Two (2) Operator and Service Manuals in hard copy and One (1)

Operator and Service Manual in digital format (pdf)

Delivery Fully fueled and operational with on-site driver’s orientation for safe

Item No. 4 - Furnish and Deliver ONE (1) New, Skid Steer Sweeper, CAT 272D, Kubota SSV75, Case SV340B, or acceptable alternate, with the following specifications:

Type All Wheel Drive Skid Steer Loader

Engine Diesel 4 Stroke Turbocharged, Minimum 70hp

Fuel System Direct High Pressure Fuel Injection

P a g e | 10

Drive Train Two (2) Speed Hydrostatic All Wheel Drive with Forward and Reverse

Coupler Hydraulic or Mechanical

Cabin ROPS/FOPS Cab with Side Screens

Steering Hydraulic Power Steering

Tipping Load Minimum 5,000 pounds

Maximum Overall Operating Height

120-inches

Ground Clearance Minimum 8-inches

Gauges and Alarms

Gauges:

Fuel Level Hour meter Tachometer

Alarms:

Engine Coolant Temperature Engine Oil Pressure Hydraulic Oil Temperature Back up Alarm

Lights Two (2) Rear Tail Lights Two (2) Halogen Working Lights Dome Light

Mirrors Rear View Mirrors: Two (2) Inside, Two (2) Outside

Operator Environment

Enclosed Cab with Air Conditioning and Heating Windshield Wiper Windshield Defroster Tilt Steering Wheel Retractable Seat Belt

Operating Conditions

Must maintain full operating capacity up to 10,000 feet above sea level without power derating, and shall not exceed more than 10 percent power derating at 14,000 feet above sea level

Attachments Original Equipment Manufacturer (OEM) 84-inch Angle Broom Pallet Fork 4 in 1 Bucket

Keys and Manual Three (3) Sets of Original Keys Two (2) Operator and Service Manuals in hard copy and One (1)

Operator and Service Manual in digital format (pdf)

P a g e | 11

Delivery Fully fueled and operational with on-site driver’s orientation for safe

All questions pertaining to the Technical Specifications must be submitted electronically through HIePRO. Questions must be submitted by November 9, 2026. Responses will be posted on November 18, 2026.

The University may refuse to answer any questions received outside of HIePRO or after the Questions/Answers deadline.

Bidders are cautioned to review the Technical Specifications carefully and thoroughly.

Objections to or requests for clarification of the specifications shall be made through HIePRO as a Question or in writing in accordance with the General Provisions to the Office of Procurement Management prior to the submittal of a bid. The submittal of a bid shall be considered as acceptance of the specifications as published.

P a g e | 12

SPECIAL PROVISIONS

1. SCOPE

The Furnishing and Delivery of Heavy Equipment for Center for Maunakea Stewardship, University of Hawaii at Hilo, University of Hawaii, Hilo, Hawaii shall be in accordance with the terms and conditions of IFB No. 27-6154 and the General Provisions dated September 2013 included by reference. Copies of the General Provisions are available at the Office of Procurement Management, University of Hawaii, 1400 Lower Campus Road, Room 15, Honolulu, Hawaii 96822 or the General Provisions may be viewed at:

https://www.hawaii.edu/procurement/vendor-info/terms-and-conditions/general-provisions-for-goods-and-services/

2. AUTHORITY

IFB No. 27-6154 is issued under the provisions of Hawaii Revised Statutes, Chapters 103 and 103D. All prospective bidders are charged with presumptive knowledge of all requirements of the cited legal authorities. Submission of a valid executed bid by any prospective bidder shall constitute an affirmation of such knowledge on the part of such prospective bidder.

3. TECHNICAL REPRESENTATIVE OF THE PROCUREMENT OFFICER (TRPO)

The Technical Representative of the Procurement Officer is Alika Toledo, Center for

Maunakea Stewardship Utilities Manager, University of Hawaii at Hilo, phone: (808) 935-0193, cellular phone: (808) 756-1282.

4. BIDDER'S QUALIFICATIONS

To qualify to bid on the specified goods and/or services, the bidder must be engaged in a business whose primary and customary interest is to provide the specified goods and/or services. The bidder must also have the requisite experience, appropriate forms of insurance, and proper licenses. In addition, the bidder shall be the manufacturer or its authorized reseller of the brand of equipment offered by the bidder. The bidder shall provide to the University documentation from the manufacturer that the bidder is an authorized reseller. The University reserves the right to disqualify any potential bidder if, in its discretion, the University determines that the bidder does not have the requisite experience, expertise to provide the goods and/or services, or is not the manufacturer or authorized reseller.

5. SUBMITTAL OF TECHNICAL DATA

With their bids, bidders shall submit, in duplicate, manufacturer's literature or brochures with technical data and illustrations of the equipment being offered.

P a g e | 13

6. BRAND NAME OR ACCEPTABLE ALTERNATE

The brand name(s) identified in the Technical Specifications are used as a measure of quality and performance. Any brand of comparable or better quality and performance than that specified will be considered for acceptance by the University. However, the University reserves the right to reject or deny any substitution that it may, in its discretion, deem unacceptable, and the findings in this regard shall be accepted by the bidder as final and binding.

7. MANUALS AND INSTRUCTIONS

The Contractor shall provide the University with operating and maintenance manuals of the equipment furnished under this contract.

8. DISCONTINUED EQUIPMENT MODELS

If any of the equipment models are discontinued at the time of delivery, the Contractor shall provide to the University a letter from the manufacturer, on company letterhead, stating the item number and manufacturer model being discontinued, the replacement manufacturer and model number, and verifying statement that the replacement meets or exceed the minimum Technical Specifications. The Contractor shall furnish and deliver the replacement equipment model at the original bid price.

9. DAMAGED/DEFECTIVE EQUIPMENT

The University reserves the right to reject damaged or defective equipment, which shall be promptly and satisfactorily replaced by the Contractor at no additional cost of the University.

10. DELIVERY

Delivery of all equipment shall be made within ONE HUNDRED TWENTY (120) consecutive calendar days from the date designated in the Notice to Proceed. The Contractor shall contact the Technical Representative to coordinate delivery for the equipment being furnished under this contract. All equipment shall be delivered to Hale Pohaku, 44-374 Maunakea Access Road (Mile Marker 6), Maunakea State Park, Hawaii 96720.

P a g e | 14

11. WARRANTY

The equipment furnished shall be new and as specified. The Contractor shall warrant that all equipment furnished under this contract shall be guaranteed for the period as designated in the Technical Specifications from the date of acceptance. The Contractor shall replace and/or repair any defective equipment and/or parts at no cost to the University during the period of warranty, provided such defects are not due to abuse or negligence on the part of the University. Repair services must be available locally, shall be prompt, effective, and performed by qualified technicians.

12. PAYMENT

The Contractor shall be remunerated upon submission of a properly executed original invoice indicating the contract number, to Office of Contracts, Procurements and Payments, University of Hawaii at Hilo, 200 W. Kawili Street, Hilo, Hawaii 96720, no later than THIRTY (30) calendar days following receipt of invoice or acceptance of goods, whichever is later.

File details come from the government source that posted it. Updated .