Q-A_Package.pdf

Buy # 919876_03

© 2001 - 2018 FedBid, Inc. All rights reserved. Page 7 / 11

Quest. # Timestamp Description Asked By Seller Organization

05/10/2018 06:32

REVISED SELLER QUESTION

1. What is building slab thickness and concrete psi and soil conditions for seismic footplate requirements and allowable loads? 2. Per specs pallets will be worked in the Drive-In with the Pallets 40” wide x 48” deep.

FEMA would have to a fork truck to fit thru the Drive-In arms. 3. Upright frame: specs state for the pallet rack height 20’ high however it should be 24’ high. If the pallet is 55” high and the beam is 5” high there would be 4 openings up to the top of the beam of 60” x 4 levels = 20’ high, there is NO space between the top of the pallet and the bottom of the beam.

4. 45 days is too short for completion.

BUYER RESPONSE

1. Per building owner, the slab thickness varies from 8 to 12 inches.

No information is currently available on concrete psi or soil conditions.

The warehouse has been previously used for installed racking systems. 2.

Yes, pallets will be worked in a drive -in / drive through with the pallets 40" wide x 48" deep. Both stand up and sit-down counter balance forklifts will be used within the warehouse. 3.

Correction. Upright frame 24' high 4.

Requirement of 45 days is to complete in installation for loading and preparedness of racking system for hurricane season response.

Hurricane season beings June 1. See answer to previous question concerning the 45 days. In your required response and attachment state how many days you anticipate completion if greater than 45 days.

545093 05/09/2018 10:02

05/09/2018 19:55

REVISED SELLER QUESTION

1. Please provide the zip code to determine seismic requirements for the area? 2. Should we deviate from the floorplan to add more pallet positions? 3. There are no dimensions shown on the plan for the racked areas. Please confirm a

© 2001 - 2018 FedBid, Inc. All rights reserved. Page 8 / 11

Quest. # Timestamp Description Asked By Seller Organization minimum of 110’ area width to accommodate drive in pallet widths of 48”. 4. -What is a “structural roll formed” rail as described for the drive in rail? Typical is either structural or roll formed. Which is being requested? 5. Will the same forklift for selective rack be used for the drive in rack requiring the same 12’-6” right angle turning radius? 6.

To determine Drive in system requirements there is a need forklift dimensions or specs. Tread width, cage width, cage and mast height, guard height etc. 7 Clear height between pallets and beams in selective rack is 10”. Is there a clear height requirement for the drive in rack? 8. Tunnel bays are not noted on the floorplan or in the spec. How many beam levels will there be in the 12’ wide tunnel bays? 9. Is there a spec for the end of aisle guards? 10.

Is there a specific guard requirement?

BUYER RESPONSE

1. 00961 2. Floor plan layout provided with SOW is a draft / sample. The minimum of 4500 pallet positions may require space deviation from the draft / sample layout. The minimum 10' traffic zone along interior perimeter is required and a minimum of 30' traffic zone along dock bay doors area (indicated on draft / sample layout as "40' Traffic Zone") is required. 3 Dimensions shown on plan for racked areas are draft / sample dimensional representation and not specific. The minimum of 4500 pallet positions may require space deviation from the draft / sample layout. The minimum 10' traffic zone along interior perimeter is required and a minimum of 30' traffic zone along dock bay doors area (indicated on draft / sample layout as "40' Traffic Zone") is required. 4. Correction to read "structural or roll formed". 5. Yes, both stand up and sit-down counter balance forklifts will be used within the warehouse. Counter balance forklifts are frequently rental units and vary. Sample models in use include CAT GP25N, Nissan MCPLO2A25LV, and Hyster H40XM. 6.

Forklifts are normally rental equipment and dimensions can vary.

Sample forklifts in use includeCAT GP25N, Nissan MCPLO2A25LV, and Hyster H40XM. 7. 10" minimum clear height requirement for drive in rack between pallets and beams. 8.

Quest. # Timestamp Description Asked By Seller Organization

Tunnel bays are not anticipated as required for minimum 4500 pallet positions. The detail is provided as specification if vendors layout is to include tunnel bays for minimum of 4500 pallet positions. 9.

Requirements for column guard state they must be floor anchored type, but also states anchors cannot protrude into the pallet space area.

10. Aisle guards should anchor behind guard and not protrude into the pallet space area.

545010 05/08/2018 14:51

FedBid FedBidREVISED SELLER QUESTION

1. Please clarify: Are Pallets being worked 40" deep x 48" wide"? 2.

BUYER RESPONSE

1. Yes - this is a correction to earlier question answered: Pallets being worked are 40" deep x 48" wide"

Previous Questions / Responses

Quest. # Timestamp Description Asked By Seller Organization

545231 Late

05/09/2018 20:09

REVISED SELLER QUESTION

Please confirm minimum aisle width for forklifts at all heights

BUYER RESPONSE

12 foot, 6 inch