Havana Utility Body Specs~3.pdf

Office of Water Resources is soliciting bids for a Utility Body to be installed on the Chassis of a Dual Rear Wheel 2024 model year F-550 with a 108” Cab to Axle length. Vehicle will be delivered to vendor and picked up from the vendor.

Vendor should provide product literature with the quote. Delivery shall be F.O.B. (freight on board) destination, and shipping costs to be included with bid. The use of a brand name is for describing the standard of quality, performance, and characteristics desired and is not intended to limit or restrict competition. Or Equal submissions will not be rejected because of minor differences in design, construction or features that do not affect the suitability of the product for its intended use. Burden of proof that the product is equal is on the bidder.

DIMENSIONS

1) Compatible with a MY 2024 Ford F-550 diesel 4x4 with a 108” Cab to Axle length.

2) Body Length 156” to 158”

3) Body Width 94” to 96”

4) Compartment Depths 20” to 21”

5) Floor Width 54”

6) Body Height 40” to 42”

7) Transverse and Bottle Gas Compartment Height 60”

ACCESSORIES

1) Heavy duty, stainless steel 3 point D ring door latches with rollers on slide rods.

2) All locks shall be keyed the same.

3) Master locking system for both sides.

4) Rear, high position lights with external protection/guards shall be installed outside of body compartments.

5) All compartments must be installed with full perimeter seals to provide weatherproofing to all compartments.

6) Flared fenders above dual rear wheels

7) All doors shall be equipped with gas shock door retainers and safety chains.

8) Horizontal doors will be one piece, drop down style with continuous stainless steel hinge.

9) Vertical doors to be equipped with a minimum of 3 stainless steel hinges or a single continuous stainless steel hinge.

10) All lights, including stop, tail, turn, back up, side lights and markers, and license plate light and bracket shall be provided and installed. Rear lights shall be outfitted with optional flashers.

11) Back-up Camera to be installed.

12) Rear recessed, step bumper with vice mount to be installed. Class V receiver hitch mounted under and flush to bumper with safety chain hooks.

Mounting shall transfer tongue weight of trailer to truck frame.

13) A 2 5/16” gooseneck hitch rated for 30,000 lbs. to be installed. Hitch shall be a turnover style hitch, or other underbed/recessed style mounting. Hitch shall be mounted over axles to properly transfer weight to truck frame.

14) Rubber Mud flaps

15) All light, camera, and other electrical wiring shall be connected to OEM truck wiring in a water tight junction box. All electrical splices shall be made with water tight manufactured plugs or contained in watertight junction boxes.

No intermittent wiring splicing will be allowed.

16) Back of the body shall be outfitted with a tailgate.

17) Floor shall be outfitted with four 6000 lbs. capacity recessed tie-down D-rings. Front rings shall be installed a minimum of 45” from the back of the transverse compartment. The rear rings shall be installed 6” to 10” from the rear of the body.

18) Floor shall be outfitted with tread plating.

19) 7-pin wiring harnesses for trailer connections shall be included at the bumper hitch and at gooseneck frame hitch.

COMPARTMENTS

1) Included sketches contain dimensions for the body and all compartments.

Dimensions are for the overall compartment height/width and depth.

2) Front compartments shall be raised compartments.

3) Compartments shall be 20” to 21” in depth.

4) All shelves shall be removable and adjustable within their compartments.

5) All shelves shall be rated to a minimum of 250 lbs. load capacity.

DRIVER’S SIDE

A) Compartment A is to be a raised, transverse or pass through style compartment 32” to 34” in width and 60” in height. Compartment shall contain three pullout drawers.

B) Compartment B shall be a minimum of 24” wide. Compartment shall be outfitted with steel mechanics drawers for tools. Compartment shall be outfitted with a minimum of 6 drawers.

C) Compartment C shall be outfitted with steel mechanics drawers for tools.

Compartment shall be outfitted with a minimum of 6 drawers. Compartment B and C can be combined into single compartment with double doors. If a double compartment configuration is proposed, the combined compartment shall be outfitted with a minimum of 6 steel mechanic drawers.

D) Compartment D shall be a horizontal style compartment over the wheel well.

E) Compartment E shall be outfitted with a minimum of 2 divider shelves.

PASSENGER SIDE

A) Compartment A is to be a raised compartment 32-34” in width and 60” in height. Compartment will be a bottle cylinder storage compartment and shall be vented and outfitted with a bottle cylinder retainer.

B) Compartment B shall be a minimum of 24” wide. Compartment shall be outfitted with 2 shelves.

C) Compartment C shall be outfitted with 2 shelves. Compartment B and C can be combined into single compartment with double doors. If a double compartment configuration is proposed, the combined compartment shall be outfitted with 2 shelves.

D) Compartment D shall be a horizontal style compartment over the wheel well.

E) Compartment E shall be outfitted with a minimum of 2 divider shelves.

PAINT AND WARRANTY

1) Prime Coat: a cured corrosion resistant primer shall be utilized.

2) Undercoat: Non-hardening rust preventative

3) Exterior paint shall be painted anti-matter Blue to match the cab.

4) Vendor shall provide a standard manufacturer’s no rust warranty.

5) Vendor shall provide a minimum 1-year standard manufacturer’s warranty

6) Vendor must be the authorized dealer to provide the body, installation and service.

7) Vendor shall provide any shop drawings, literature and users/owner’s manuals.