099123_-_INTERIOR_PAINTING.pdf

IRS ENTERPRISE COMPUTER CENTER COOLING TOWER

250 Murall Drive

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

SECTION 099123 - INTERIOR PAINTING

GENERALPART 1 -

RELATED DOCUMENTS1.1

Drawings and general provisions of the Contract, including General and SupplementaryA.

Conditions and Division 01 Specification Sections, apply to this Section.

SUMMARY1.2

Section includes surface preparation and the application of paint systems on interiorA.

substrates.

Concrete.1.

Cement board.2.

Clay masonry.3.

Concrete masonry units (CMUs).4.

Steel and iron.5.

Galvanized metal.6.

Aluminum (not anodized or otherwise coated).7.

Copper.8.

Stainless steel.9.

Fiberglass.10.

Plastic.11.

Gypsum board.12.

Plaster.13.

Related Requirements:B.

Section 051200 "Structural Steel Framing" for shop priming structural steel.1.

Section 055000 "Metal Fabrications" for shop priming metal fabrications.2.

Section 055213 "Pipe and Tube Railings" for shop painting pipe and tube railings.3.

for shop priming metal gratings.4.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 1 Bid Documents

11 MARCH 2016

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

DEFINITIONS1.3

MPI Gloss Level 1: Not more than five units at 60 degrees and 10 units at 85 degrees,A.

according to ASTM D 523.

MPI Gloss Level 2: Not more than 10 units at 60 degrees and 10 to 35 units at 85B.

degrees, according to ASTM D 523.

MPI Gloss Level 3: 10 to 25 units at 60 degrees and 10 to 35 units at 85 degrees,C.

according to ASTM D 523.

MPI Gloss Level 4: 20 to 35 units at 60 degrees and not less than 35 units at 85 degrees,D.

according to ASTM D 523.

MPI Gloss Level 5: 35 to 70 units at 60 degrees, according to ASTM D 523.E.

MPI Gloss Level 6: 70 to 85 units at 60 degrees, according to ASTM D 523.F.

MPI Gloss Level 7: More than 85 units at 60 degrees, according to ASTM D 523.G.

ACTION SUBMITTALS1.4

Product Data: For each type of product. Include preparation requirements and applicationA.

instructions.

Include Printout of current "MPI Approved Products List" for each product category1.

specified, with the proposed product highlighted.

Indicate VOC content.2.

Samples for Initial Selection: For each type of topcoat product.B.

Samples for Verification: For each type of paint system and in each color and gloss ofC.

topcoat.

Submit Samples on rigid backing, 8 inches (200 mm) square.1.

Apply coats on Samples in steps to show each coat required for system.2.

Label each coat of each Sample.3.

Label each Sample for location and application area.4.

Product List: Cross-reference to paint system and locations of application areas. UseD.

same designations indicated on Drawings and in schedules. Include color designations.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 2

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

MAINTENANCE MATERIAL SUBMITTALS1.5

Furnish extra materials, from the same product run, that match products installed andA.

that are packaged with protective covering for storage and identified with labels describing contents.

Paint: 5 percent, but not less than 1 gal. (3.8 L) of each material and color applied.1.

DELIVERY, STORAGE, AND HANDLING1.6

Store materials not in use in tightly covered containers in well-ventilated areas withA.

ambient temperatures continuously maintained at not less than 45 deg F (7 deg C).

Maintain containers in clean condition, free of foreign materials and residue.1.

Remove rags and waste from storage areas daily.2.

FIELD CONDITIONS1.7

Apply paints only when temperature of surfaces to be painted and ambient airA.

temperatures are between 50 and 95 deg F (10 and 35 deg C).

Do not apply paints when relative humidity exceeds 85 percent; at temperatures less thanB.

5 deg F (3 deg C) above the dew point; or to damp or wet surfaces.

PRODUCTSPART 2 -

MANUFACTURERS2.1

Manufacturers: Subject to compliance with requirements, provide products by one of theA.

following:

Benjamin Moore & Co.1.

Coronado Paint; Benjamin Moore Company.2.

Glidden Professional.3.

M.A.B. Paints.4.

PPG Architectural Finishes, Inc.5.

Sherwin-Williams Company (The).6.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 3 Bid Documents

11 MARCH 2016

http://www.specagent.com/LookUp/?uid=123457035134&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123457035137&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123457035143&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123457035146&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123457035148&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123457035152&mf=04&src=wd

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Products: Subject to compliance with requirements, provide one of the products listed inB.

the Interior Painting Schedule for the paint category indicated.

PAINT, GENERAL2.2

MPI Standards: Products shall comply with MPI standards indicated and shall be listed inA.

its "MPI Approved Products Lists."

Material Compatibility:B.

Materials for use within each paint system shall be compatible with one another and1.

substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience.

For each coat in a paint system, products shall be recommended in writing by2.

topcoat manufacturers for use in paint system and on substrate indicated.

VOC Content: For field applications that are inside the weatherproofing system, paintsC.

and coatings shall comply with VOC content limits of authorities having jurisdiction and the following VOC content limits:

Flat Paints and Coatings: 50 g/L.1.

Nonflat Paints and Coatings: 50 g/L.2.

Primers, Sealers, and Undercoaters: 100 g/L.3.

Rust-Preventive Coatings: 100 g/L.4.

Zinc-Rich Industrial Maintenance Primers: 100 g/L.5.

Pretreatment Wash Primers: 420 g/L.6.

Colors: As selected by Architect from manufacturer's full range.D.

Thirty percent of surface area will be painted with deep tones.1.

SOURCE QUALITY CONTROL2.3

Testing of Paint Materials: Owner reserves the right to invoke the following procedure:A.

Owner will engage the services of a qualified testing agency to sample paint1.

materials. Contractor will be notified in advance and may be present when samples are taken. If paint materials have already been delivered to Project site, samples may be taken at Project site. Samples will be identified, sealed, and certified by testing agency.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 4

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Testing agency will perform tests for compliance with product requirements.2.

Owner may direct Contractor to stop applying paints if test results show materials3.

being used do not comply with product requirements. Contractor shall remove noncomplying paint materials from Project site, pay for testing, and repaint surfaces painted with rejected materials. Contractor will be required to remove rejected materials from previously painted surfaces if, on repainting with complying materials, the two paints are incompatible.

EXECUTIONPART 3 -

EXAMINATION3.1

Examine substrates and conditions, with Applicator present, for compliance withA.

requirements for maximum moisture content and other conditions affecting performance of the Work.

Maximum Moisture Content of Substrates: When measured with an electronic moistureB.

meter as follows:

Concrete: 12 percent.1.

Fiber-Cement Board: 12 percent.2.

Masonry (Clay and CMUs): 12 percent.3.

Gypsum Board: 12 percent.4.

Plaster: 12 percent.5.

Gypsum Board Substrates: Verify that finishing compound is sanded smooth.C.

Plaster Substrates: Verify that plaster is fully cured.D.

Verify suitability of substrates, including surface conditions and compatibility, with existingE.

finishes and primers.

Proceed with coating application only after unsatisfactory conditions have beenF.

corrected.

Application of coating indicates acceptance of surfaces and conditions.1.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 5

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

PREPARATION3.2

Comply with manufacturer's written instructions and recommendations in "MPIA.

Architectural Painting Specification Manual" applicable to substrates and paint systems indicated.

Remove hardware, covers, plates, and similar items already in place that are removableB.

and are not to be painted. If removal is impractical or impossible because of size or weight of item, provide surface-applied protection before surface preparation and painting.

After completing painting operations, use workers skilled in the trades involved to1.

reinstall items that were removed. Remove surface-applied protection if any.

Clean substrates of substances that could impair bond of paints, including dust, dirt, oil,C.

grease, and incompatible paints and encapsulants.

Remove incompatible primers and reprime substrate with compatible primers or1.

apply tie coat as required to produce paint systems indicated.

Concrete Substrates: Remove release agents, curing compounds, efflorescence, andD.

chalk. Do not paint surfaces if moisture content or alkalinity of surfaces to be painted exceeds that permitted in manufacturer's written instructions.

Masonry Substrates: Remove efflorescence and chalk. Do not paint surfaces if moistureE.

content or alkalinity of surfaces or mortar joints exceeds that permitted in manufacturer's written instructions.

Steel Substrates: Remove rust, loose mill scale, and shop primer, if any. Clean usingF.

methods recommended in writing by paint manufacturer but not less than the following:

SSPC-SP 2.1.

SSPC-SP 3.2.

SSPC-SP 7/NACE No. 4.3.

SSPC-SP 11.4.

Shop-Primed Steel Substrates: Clean field welds, bolted connections, and areas whereG.

shop paint is abraded. Paint exposed areas with the same material as used for shop priming to comply with SSPC-PA 1 for touching up shop-primed surfaces.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 6

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Galvanized-Metal Substrates: Remove grease and oil residue from galvanized sheetH.

metal by mechanical methods to produce clean, lightly etched surfaces that promote adhesion of subsequently applied paints.

Aluminum Substrates: Remove loose surface oxidation.I.

APPLICATION3.3

Apply paints according to manufacturer's written instructions and to recommendations inA.

"MPI Manual."

Use applicators and techniques suited for paint and substrate indicated.1.

Paint surfaces behind movable equipment and furniture same as similar exposed2.

surfaces. Before final installation, paint surfaces behind permanently fixed equipment or furniture with prime coat only.

Paint front and backsides of access panels, removable or hinged covers, and3.

similar hinged items to match exposed surfaces.

Do not paint over labels of independent testing agencies or equipment name,4.

identification, performance rating, or nomenclature plates.

Primers specified in painting schedules may be omitted on items that are factory5.

primed or factory finished if acceptable to topcoat manufacturers.

Tint each undercoat a lighter shade to facilitate identification of each coat if multiple coatsB.

of same material are to be applied. Tint undercoats to match color of topcoat, but provide sufficient difference in shade of undercoats to distinguish each separate coat.

If undercoats or other conditions show through topcoat, apply additional coats until curedC.

film has a uniform paint finish, color, and appearance.

Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brushD.

marks, roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks.

Painting Fire Suppression, Plumbing, HVAC, Electrical, Communication, and ElectronicE.

Safety and Security Work:

Paint the following work where exposed in equipment rooms:1.

Equipment, including panelboards and switch gear.a.

Uninsulated metal piping.b.

Uninsulated plastic piping.c.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 7

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Pipe hangers and supports.d.

Metal conduit.e.

Plastic conduit.f.

Tanks that do not have factory-applied final finishes.g.

Duct, equipment, and pipe insulation having cotton or canvas insulationh.

covering or other paintable jacket material.

Paint the following work where exposed in occupied spaces:2.

Equipment, including panelboards.a.

Uninsulated metal piping.b.

Uninsulated plastic piping.c.

Pipe hangers and supports.d.

Metal conduit.e.

Plastic conduit.f.

Duct, equipment, and pipe insulation having cotton or canvas insulationg.

covering or other paintable jacket material.

Other items as directed by Architect.h.

Paint portions of internal surfaces of metal ducts, without liner, behind air inlets and3.

outlets that are visible from occupied spaces.

FIELD QUALITY CONTROL3.4

Dry Film Thickness Testing: Owner may engage the services of a qualified testing andA.

inspecting agency to inspect and test paint for dry film thickness.

Contractor shall touch up and restore painted surfaces damaged by testing.1.

If test results show that dry film thickness of applied paint does not comply with2.

paint manufacturer's written recommendations, Contractor shall pay for testing and apply additional coats as needed to provide dry film thickness that complies with paint manufacturer's written recommendations.

CLEANING AND PROTECTION3.5

At end of each workday, remove rubbish, empty cans, rags, and other discardedA.

materials from Project site.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 8

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

After completing paint application, clean spattered surfaces. Remove spattered paints byB.

washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces.

Protect work of other trades against damage from paint application. Correct damage toC.

work of other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, and leave in an undamaged condition.

At completion of construction activities of other trades, touch up and restore damaged orD.

defaced painted surfaces.

INTERIOR PAINTING SCHEDULE3.6

Concrete Substrates, Nontraffic Surfaces:A.

High-Performance Architectural Latex System MPI INT 3.1C:1.

Prime Coat: Primer, alkali resistant, water based,MPI#3.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3), MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4),MPI#140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5),MPI MPI #141.

Concrete Stain System :2.

First Coat: Stain, interior, matching topcoat.a.

Topcoat: Stain, interior,MPI#58.b.

Concrete Substrates, Traffic Surfaces:B.

Concrete Stain System :1.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 9

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

First Coat: Stain, interior, for concrete floors, matching topcoat.a.

Topcoat: Stain, interior, for concrete floors, MPI #58.b.

Water-Based Concrete Floor Sealer System MPI INT3.2G:2.

First Coat: Sealer, water based, for concrete floors, matching topcoat.a.

Topcoat: Sealer, water based, for concrete floors,MPI#99.b.

Cement Board Substrates:C.

High-Performance Architectural Latex System MPI INT 3.3B:1.

Prime Coat: Primer, alkali resistant, water based, MPI #3.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3),MPI MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4), MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5),MPI#141.

Clay Masonry Substrates:D.

High-Performance Architectural Latex System MPI INT 4.1L:1.

Prime Coat: Primer, alkali resistant, water based, MPI #3.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3),MPI#139.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 10

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4),MPI#140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5), MPI #141.

CMU Substrates:E.

High-Performance Architectural Latex System MPI INT 4.2D MPI INT 4.2P:1.

Block Filler: Block filler, latex, interior/exterior, MPI #4.a.

Prime Coat: Primer, alkali resistant, water based,MPI#3.b.

Intermediate Coat: Latex, interior, high performance architectural, matchingc.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 3),MPI#139.

Topcoat: Latex, interior, high performance architectural (MPI Glossf.

Level 4), MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossg.

(MPI Gloss Level 5),MPI#141.

Steel Substrates:F.

High-Performance Architectural Latex System MPI INT 5.1R MPI INT 5.1RR:1.

Prime Coat: Primer, alkyd, quick dry, for metal, MPI #76.a.

Prime Coat: Primer, alkyd, anti-corrosive, for metal,MPI#79.b.

Prime Coat: Shop primer specified in Section where substrate is specified.c.

Intermediate Coat: Latex, interior, high performance architectural, matchingd.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 2), MPI #138.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 11

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Topcoat: Latex, interior, high performance architectural (MPI Glossf.

Level 3), MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glossg.

Level 4),MPI MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossh.

(MPI Gloss Level 5), MPI #141.

Galvanized-Metal Substrates:G.

High-Performance Architectural Latex System MPI INT 5.3M:1.

Prime Coat: Primer, galvanized, water based,MPI#134.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3),MPI#139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4), MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5),MPI#141.

Aluminum (Not Anodized or Otherwise Coated) Substrates:H.

High-Performance Architectural Latex System MPI INT 5.4F:1.

Prime Coat: Primer, quick dry, for aluminum, MPI #95.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3),MPI#139.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 12

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4), MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5),MPI#141.

Copper Substrates:I.

High-Performance Architectural Latex System MPI INT 5.5F:1.

Prime Coat: Primer, quick dry, for aluminum, MPI #95.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3),MPI MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4), MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5),MPI MPI#141.

Stainless-Steel Substrates:J.

High-Performance Architectural Latex System MPI INT 5.6G:1.

Prime Coat: Primer, bonding, solvent based, MPI #69.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2),MPI MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3), MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4),MPI#140.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 13

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5), MPI #141.

Fiberglass Substrates:K.

High-Performance Architectural Latex System MPI INT 6.7H:1.

Prime Coat: Primer, bonding, water based,MPI#17.a.

Prime Coat: Primer, bonding, solvent based, MPI #69.b.

Intermediate Coat: Latex, interior, high performance architectural, matchingc.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 2),MPI#138.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 3), MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glossf.

Level 4), MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossg.

(MPI Gloss Level 5),MPI MPI#141.

Plastic Substrates:L.

High-Performance Architectural Latex System MPI INT 6.8A:1.

Prime Coat: Primer, bonding, solvent based,MPI MPI#69.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3), MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4),MPI MPI #140.

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 14

Kearneysville, West Virginia

GSA # GS-P-03-15-DX-5027

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5), MPI #141.

Gypsum Board and Plaster Substrates:M.

High-Performance Architectural Latex System MPI INT 9.2B:1.

Prime Coat: Primer sealer, latex, interior,MPI#50.a.

Intermediate Coat: Latex, interior, high performance architectural, matchingb.

topcoat.

Topcoat: Latex, interior, high performance architectural (MPI Glossc.

Level 2), MPI #138.

Topcoat: Latex, interior, high performance architectural (MPI Glossd.

Level 3), MPI #139.

Topcoat: Latex, interior, high performance architectural (MPI Glosse.

Level 4),MPI MPI #140.

Topcoat: Latex, interior, high performance architectural, semi-glossf.

(MPI Gloss Level 5),MPI#141.

Insulation-Covering Substrates: Including pipe and duct coverings.N.

END OF SECTION 099123

INTERIOR PAINTING

PROPERTY OF THE U.S. GOVERNMENT - FOR OFFICIAL USE ONLY

Do not remove this notice - Properly destroy documents when no longer needed

099123 - 15

Products: Subject to compliance with requirements, provide one of the products listed in the Interi