FuelCells_PID_Pack_text.pdf

*** Product Number: 001467701

** PID Text

TANK, FUEL, AIRCRAFT

***** CRITICAL APPLICATION ITEM *****

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT:

htp://www.dla.mil/HQ/Acquisi�on/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RD002, COVERED DEFENSE INFORMATION APPLIES

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS

(MANUFACTURERS AND NON-MANUFACTURERS)

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL

REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to export-control of either the Interna�onal Traffic in Arms regula�ons

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal employees and U.S. companies and their foreign subsidiaries. DFARS

252.225-7048 is applicable to this data.

The Defense Logis�cs Agency (DLA) limits distribu�on of export-control technical data to DLA contractors that have an approved US/Canada Joint

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the export-controlled data can be found at:

htps://www.dla.mil/Logis�cs-Opera�ons/Enhanced-Valida�on/

To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP cer�fica�on and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data.

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

A NORTHROP GRUMMAN LICENSE AGREEMENT 14 RESTRICTED TECHNICAL DATA

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

T-38, F-5" LICENSE AGREEMENT FOLDER AVAILABLE AT

htps://pcf1x.bsm.dla.mil/cFolders

SHELF LIFE MONTHS 48

MATERIAL REFERENCE NUMBER__14-52901-1

******** ENGINEERING DATA LIST DTD 09 JAN 2019 REV 5 *******

14-52901__98C0534-H

3-00933__W/AP A, B, C, D<(>,<)>

THE CONTRACTOR SHALL USE THE MOST CURRENT AMENDMENTS APPLICABLE TO EACH

DRAWING, MIL SPEC, MIL STD, INDUSTRY SPEC OR INDUSTRY STD AS OF THE

EFFECTIVE DATE OF THIS CONTRACT UNLESS OTHERWISE NOTED.

***** ENGINEERING DATA REQUIREMENTS DTD 09 JAN 2019 *****

(ATTACHMENT "A")

1-3 NOT APPLICABLE

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF

THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO

INDICATED.

5. MARKING PER MIL-STD-130.

6. IUID (ITEM UNIQUE IDENTIFIER) IS REQUIREMENTS AND EXPECTATIONS WHICH

THE CONTRACTOR MUST ENSURE

ARE COMPLIED WITH.

7. CONTRACTORS DRAWINGS SHALL BE CHANGED OR SUPPLEMENTED BY CONTRACTOR

FOR IUID COMPLIANCE.

A. LABEL SHALL CONTAIN ALL DATA ON EXISTING LABEL, (IF EXISTING LABEL IS

TO BE REPLACED), ONLY

DELETE EXISTING LABEL WITH GOVERNMENT ENGINEERING PERMISSION.

B. USE HRI (HUMAN READABLE) AND MACHINE READABLE MATRIX. (USAF NOT

EQUIPPED TO READ BARCODE).

C. IUID MATRIX NEEDS TO BE HIGHLY VISIBLE, IN A LOCATION EASILY

ACCESSIBLE.

D. IUID MARKING MUST BE PERMANENT.

E. MIL-STD-130, ANSI/AIM BCII, ISO 15434, ISO 15415, AND ISO 15418

F. IUID MARKING SPECIFICATIONS<(>,<)>

1. MINIMUM 1/8 INCH LETTERING ON HUMAN READABLE TO INCLUDE:

A. CAGE (17V)

B. P/N (1P)

C. SERIAL NUMBER (IS)

2. MINIMUM 1/4 INCH SQUARE ON MACHINE READABLE 2D MATRIX -CONSTRUCT 2 -

TO INCLUDE:

A. CAGE (17V)

B. P/N (1P)

C. SERIAL NUMBER (IS)

FIRST ARTICLE

==================NOTIFY TEST SITE 30 DAYS===================

=============PRIOR TO SHIPMENT OF FIRST ARTICLE==============

=======MARK FOR FIRST ARTICLE INSPECTION AND TESTING=========

=========================DO NOT POST=========================

Government First Ar�cle Preproduc�on approval required. Tes�ng will be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding the first ar�cle test requirements must be submited through the contrac�ng officer.

Addi�onal Wide Area Workflow (WAWF) instruc�ons for government first ar�cle test CLIN: The contractor shall code the receiving report for government first ar�cle test CLIN in WAWF as Follows:

A: Inspec�on at origin (Source) - Enter the DCMA office DODAAC listed on page 1 of the contract.

B: Acceptance by other - Enter the issue by office DODAAC listed on page

1 of the contract.

C: Ship to code - Enter the DODAAC of the test facility listed for the government first ar�cle test CLIN in the contract (See FAR Clause

52.209-4).

FIRST ARTICLE TEST MARKING INSTRUCTIONS:

FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one addi�onal side of the package.

RS058: Shelf life requirement RS001 for a TYPE 2 (CODE 6) item with a shelf life of 24 month (extendable) applies to this item.

CRITICAL APPLICATION ITEM

NORTHROP GRUMMAN TECHNICAL SERVICES, 0JRC1 P/N 14-52901-1

LINDEN STREET CAPITAL CORP 4U536 P/N 14-52901-1

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 14-52901-1

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 47500-1

IAW REFERENCE DRAWING NR 76823 3-00933

REVISION NR B DTD 01/29/1971

PART PIECE NUMBER:

REVISION NR B DTD 09/07/1971

IAW REFERENCE DRAWING NR 76823 14-52901

REVISION NR 28 DTD 06/17/1983

REVISION NR G DTD 10/17/1978

PART PIECE NUMBER: 14-52901-1

IAW REFERENCE DRAWING NR 76823 P-234

REVISION NR B DTD 11/11/1980

REVISION NR A DTD 01/01/1939

REVISION NR G DTD 03/17/1998

*** Product Number: 001467703

** PID Text

TANK, FUEL, AIRCRAFT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)

RT001: MEASURING AND TEST EQUIPMENT

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

Waivers for the coa�ng requirement on ballis�c foam items for the A-10 aircra� are no longer valid. Please refer to Spec 162S900705 for the use of coa�ngs.

Government First Ar�cle Preproduc�on approval required. Tes�ng will be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

This item requires Item Unique Iden�fica�on (IUID) in accordance with the enclosed/referenced IUID technical requirements and MIL-STD-130.

DFARS 252.211-7003 clause applies.

RS061: Shelf life requirement RS001 for a TYPE 2 (CODE 8) item with a shelf life of 48 month (extendable) applies to this item.

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 47502-1

ROYAL HOLDINGS, INC. 00333 P/N FCR56942

LINDEN STREET CAPITAL CORP 4U536 P/N 14-52903-1

NORTHROP GRUMMAN SYSTEMS CORPORATION 76823 P/N 14-52903-1

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 14-52903-1

IAW REFERENCE DRAWING NR 76823 14-52903

REVISION NR E DTD 04/12/1995

IAW REFERENCE DRAWING NR 76823 14-52903

REVISION NR E DTD 10/17/1978

PART PIECE NUMBER: 14-52903-1

IAW REFERENCE DRAWING NR 76823 10Y201

REVISION NR AG DTD 09/27/1985

REVISION NR B DTD 09/07/1971

IAW REFERENCE DRAWING NR 98747 200925111

REVISION NR E DTD 10/19/2012

REVISION NR E DTD 06/21/2018

IAW REFERENCE DRAWING NR 76823 10Y201

REVISION NR AG DTD 08/06/2020

IAW REFERENCE DRAWING NR 13873 EI-001467703

REVISION NR DTD 09/06/2023

IAW REFERENCE QAP 13873 SQAP-001467703

*** Product Number: 001761247

** PID Text

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

Item Unique Iden�fica�on is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N FCE63979

BELL TEXTRON INC 97499 P/N 205-062-635-103

*** Product Number: 001761248

** PID Text

TANK, FUEL AIRCRAFT

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

MEGGITT (ROCKMART), INC. 56221 P/N 2F1637011-2

BELL TEXTRON INC 97499 P/N 205-062-635-2

*** Product Number: 001761249

** PID Text

TANK, FUEL, AIRCRAFT ---

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

Contractor first ar�cle/preproduc�on approval tes�ng required. Use

DI-NDTI-80809B in prepara�on of the first ar�cle report. Current revision of MIL-HDBK-831 may also be used for report format guidance.

First ar�cle tes�ng shall be conducted IAW applicable drawings and drawing notes, specifica�on, engineering instruc�ons and specific requirements set forth in the contract. Addi�onally, 100% dimensional characteris�cs check shall be performed and results provided to the contrac�ng officer. The first ar�cle offered must be manufactured at the facili�es in which produc�on quan��es are procured under the contract. Contractor shall provide a statement along with objec�ve evidence that test and produc�on items meet the material and process requirements of the contract. If applicable, DD form 1423 documenta�on shall be provided as required. Unless F.A.T sample(s) is degraded or destroyed in tes�ng or submited for government fit, form, func�on verifica�on (when specified by contract), the F.A.T. samples(s) may be deliverable with the last produc�on run of the contract.

Addi�onal Wide Area Workkflow (WAWF) instruc�ons for contractor first contractor first ar�cle test CLIN in WAWF as follows:

A. Inspec�on at origin (source)- Enter the DCMA DODAAC listed on page 1 of the contract.

B. Acceptance at des�na�on- Enter the issue by office DODAAC listed

C. Ship to code - Enter the issue by office DODAAC listed on page 1 of the contract.

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

ATTACHMENTS DETAILING CONTRACTOR

FIRST ARTICLE TESTING AND/OR PRODUCTION LOT

TESTING AND/OR TECHNICAL REQUIREMENTS PACKAGE TO

INCLUDE CDRL FORM DD 1423 APPLY. ACCESS

ATTACHMENTS ON DSCR WEBSITE

htp://www.dscr.dla.mil/userweb/dscrbat/cdrls.htm

TO FIND UNDER APPLICABLE NIIN.

IAW BASIC DRAWING NR 81996 205-062-635

REVISION NR E DTD 01/10/2006

IAW REFERENCE DRAWING NR 81996 SS205-062-635

REVISION NR B DTD 06/15/2011

IAW REFERENCE QAP 13873 QAP-106

REVISION NR B DTD 07/09/2012

*** Product Number: 001761251

** PID Text

TANK, FUEL, AIRCRAFT CRITICAL APPLICATION ITEM

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

PART NUMBER_205-062-635-13 THE CONTRACTOR SHALL USE THE MOST CURRENT

AMENDMENTS APPLICABLE TO EACH DRAWING, MIL SPEC, MIL STD, INDUSTRY SPEC

OR INDUSTRY STD AS OF THE EFFECTIVE DATE OF THIS CONTRACT UNLESS

OTHERWISE NOTED. -- BELL HELICOPTER CO,. CAGE 97499 SOURCES:

MEGGITT INC., CAGE 56221 NO ALTERNATE ALLOWED --

ACQUISITION OF THIS PART IS RESTRICTED TO THE SOURCE(S) SPECIFIED ON THE

SOURCE CONTROL DRAWING. ALTERNATE OFFERS WILL NOT BE ACCEPTED. USE

PROCUREMENT NOTE L22.

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

RQ042: Non-Tailored Higher-Level Quality Requirements (ISO 9001:2015) for Manufacturers and Non-Manufacturers

IAW BASIC DRAWING NR 97499 205-062-635

REVISION NR Y DTD 08/21/1992

PART PIECE NUMBER: 205-062-635-13

IAW REFERENCE DRAWING NR 97499 205-062-635

REVISION NR Y DTD 10/08/1991

IAW REFERENCE DRAWING NR 97499 205-062-635

REVISION NR Y DTD 08/15/2011

*** Product Number: 007398336

** PID Text

TANK,FUEL,AIRCRAFT AFT DORSAL

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS

DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE

TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN

THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR

HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM),

THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM

DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON

STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS

OF THE UNDIMENSIONED DRAWING.

THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR

DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE

DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE

INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND

(+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-)

0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH

DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO

WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY.

REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED

TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY.

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

A NORTHROP GRUMMAN LICENSE AGREEMENT 14 RESTRICTED TECHNICAL DATA

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

T-38, F-5" LICENSE AGREEMENT FOLDER AVAILABLE AT

htps://pcf1x.bsm.dla.mil/cFolders

EXCEPTION:

PRODUCT VERIFICATION TESTING REQUIRED:

100% INSPECTION OF FUEL CELLS FOR BLISTERS AND HARDWARE INSTALLATION.

REQUIRE CONTRACTOR DOCUMENTATION OF PRESSURE TESTING TO BE INCLUDED

WITH DOCUMENTATION PROVIDED WITH MATERIAL INDIVIDUALLY

DRAWING EXCEPTIONS:

SEE DRAWING 007398336-13100 FOR EXCEPTIONS

3-52916 - W/EO'S 13C0214, 07A0403

Government First Ar�cle Preproduc�on approval required. Tes�ng will be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 3-52916-1

MEGGITT (ROCKMART), INC. 56221 P/N 320-4-51586-103

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 7C101-02704

IAW REFERENCE DRAWING NR 76823 NAI57-84

REVISION NR E DTD 01/01/1939

IAW REFERENCE DRAWING NR 76823 3-52916

REVISION NR J DTD 02/16/1972

PART PIECE NUMBER: 3-52916-1

IAW REFERENCE DRAWING NR 76823 3-52916

REVISION NR J DTD 03/28/2007

REVISION NR E DTD 06/30/2005

IAW REFERENCE DRAWING NR 13873 EI-007398336

REVISION NR DTD 06/27/2023

IAW REFERENCE DRAWING NR 81755 3-52916

REVISION NR DTD 01/01/1939

IAW REFERENCE QAP 13873 SQAP-007398336

REVISION NR DTD 09/07/2023

*** Product Number: 007398341

TANK, FUEL, AIRCRAFT CENTER

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

SHELF LIFE REQUIREMENT APPLIES:

RS023: Shelf-life requirement RS001 for a TYPE I (CODE S) item with a shelf life of 60 months (non-extendable) applies to this item.

NORTHROP GRUMMAN LICENSING AGREEMENT APPLIES:

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

IUID REQUIRED:

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

ENGINEERING DATA REQUIREMENTS:

THE ENGINEERING DATA REQUIREMENTS ARE UNDER DRAWING:8042013-EI-007398341

IN DMS

SOURCE APPROVAL PACKAGE REQUIRED

TO ENSURE CONTINUED PRODUCT INTEGRITY OF THE ITEM, PROCUREMENT IS

RESTRICTED TO SOURCES LISTED IN THE AMPL THESE SOURCES ARE KNOWN TO HAVE

THE REQUIRED EXPERIENCE AND CAPABILITY. FAILURE OF THIS ITEM COULD

RESULT IN LOSS OF AIRCRAFT AND CREW PERSONNEL.

THEREFORE, NEW SOURCES MUST BE APPROVED BY THE COGNIZANT SYSTEM ENGINEER

PRIOR TO CONTRACT AWARD.

A TECHNICAL DATA PACKAGE IS AVAILABLE AND MAY

BE OBTAINED FOR USE IN DEVELOPING A SOURCE

APPROVAL REQUEST (SAR) FOR ENGINEERING

SOURCE APPROVAL. TO OBTAIN A COPY OF THE

TECHNICAL DATA PACKAGE (TDP), CALL TECHNICAL

DATA MANAGEMENT CUSTOMER SERVICE

Website: htps://www.pdmd.dla.mil/cs/

(804)279-3477

FAX:(804)279-6299

e-mail:DSCR.PDMDDistribu�on@dla.mil

GOVERNMENT FIRST ARTICLE TESTING REQUIREMENTS:

Government First Ar�cle Preproduc�on approval required. Tes�ng will be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

A.PERFORMANCE OR OTHER CHARACTERISTICS WHICH THE FIRST ARTICLES MUST

MEET ARE

CONFORMANCE WITH ALL DRAWINGS AND FORM, FIT AND FUNCTION.

B. THE DETAILED TECHNICAL REQUIREMENTS FOR FIRST ARTICLE APPROVAL TESTS

ARE CONTAINED IN

DRAWINGS AND EDL. THE GOVERNMENT RESERVES THE RIGHT TO TEST TO ANY

SPECIFICATION IN THE CONTRACT.

FIRST ARTICLE DELIVERY ADDRESS:

DODAAC:FB2029

MARK AS "FIRST ARTICLE.

DO NOT SEND TO SUPPLY.

OO-ALC/809 MXSS/MXDEB

BLDG 849 ATTN: NON-ACCOUNTABLE BAY

HILL AIR FORCE BASE, UT 84056-5713

PLEASE ENSURE THE WORDS 'FIRST ARTICLE' ARE MARKED ON THE OUTSIDE OF THE

BOX IN LARGE CONSPICUOUS LETTERS.

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 3-52902-503

MEGGITT (ROCKMART), INC. 56221 P/N 320-4-51619-103

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 7C101-02701

CAE USA INC. 50237 P/N 67C101-02272

IAW REFERENCE DRAWING NR 76823 3-52902

REVISION NR K DTD 02/15/1972

PART PIECE NUMBER: 3-52902-503

IAW REFERENCE DRAWING NR 76823 3-52902

REVISION NR K DTD 01/24/2013

IAW REFERENCE DRAWING NR 79U29 RE-3-52902-503

REVISION NR DTD 01/01/1939

IAW REFERENCE QAP 13873 SQAP-007398341

REVISION NR DTD 08/14/2023

IAW REFERENCE DRAWING NR 13873 EI-007398341

REVISION NR DTD 08/01/2023

*** Product Number: 007398342

** PID Text

TANK,FUEL,AIRCRAFT (T-38 A AFT MAIN)

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

SHELF LIFE APPLIES:

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

1.SEE ENGINEERING DATA REQUIREMENTS UNDER DRAWING:

8020214-EI-007398342

2.W/EO'S 13C0211-H, 07A0402-H

3.IUID REQUIRED

IUID IS REQUIRED IAW MIL-STD-130. SPECIFIC INSTRUCTIONS FOR MARKING

METHOD, LOCATION, CONTENT

AND FORMAT SHALL BE SPECIFIED BY THE SUPPLIER AND SUBMITTED TO THE

GOVERNMENT FOR APPROVAL

PRIOR TO CONTRACT AWARD. THE SUPPLIER MUST DEMONSTRATE THAT THE MARKING

DOES NOT ADVERSELY

AFFECT ITEM INTEGRITY OR PERFORMANCE AND WILL REMAIN READABLE AND

ATTACHED THROUGHOUT THE

USABLE LIFE OF THE ITEM.

THE REQUIRED EXPERIENCE AND CAPABILITY. FAILURE OF THIS ITEM COULD

RESULT IN LOSS OF AIRCRAFT AND CREW PERSONNEL.

THEREFORE, NEW SOURCES MUST BE APPROVED BY THE COGNIZANT SYSTEM ENGINEER

PRIOR TO CONTRACT AWARD.

A TECHNICAL DATA PACKAGE IS AVAILABLE AND MAY

BE OBTAINED FOR USE IN DEVELOPING A SOURCE

APPROVAL REQUEST (SAR) FOR ENGINEERING

SOURCE APPROVAL. TO OBTAIN A COPY OF THE

TECHNICAL DATA PACKAGE (TDP), CALL TECHNICAL

DATA MANAGEMENT CUSTOMER SERVICE

Website: htps://www.pdmd.dla.mil/cs/

(804)279-3477 be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

MARK AS "FIRST ARTICLE.

DO NOT SEND TO SUPPLY.

OO-ALC/809 MXSS/MXDEB

BLDG 849 ATTN: NON-ACCOUNTABLE BAY

HILL AIR FORCE BASE, UT 84056-5713

PLEASE ENSURE THE WORDS 'FIRST ARTICLE' ARE MARKED ON THE OUTSIDE OF THE

BOX IN LARGE CONSPICUOUS LETTERS.

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 3-52901-1

MEGGITT (ROCKMART), INC. 56221 P/N 320-51692-103

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 7C101-02702

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 7C101-02702-1

IAW REFERENCE STD NR MIL-STD-129R(3)

REVISION NR R DTD 02/25/2023

IAW REFERENCE DRAWING NR 76823 3-52901

REVISION NR G DTD 02/15/1972

PART PIECE NUMBER: 3-52901-1

IAW REFERENCE DRAWING NR 76823 3-52901

REVISION NR G DTD 01/22/2013

IAW REFERENCE DRAWING NR 13873 EI-007398342

REVISION NR DTD 07/06/2023

*** Product Number: 007398343

** PID Text

TANK,FUEL,FORWARD DORSAL

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

THIS MATERIAL DOES NOT HAVE A SHELF LIFE REQUIREMENT

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

Waivers for the coa�ng requirement on ballis�c foam items for the A-10 aircra� are no longer valid. Please refer to Spec 162S900705 for the use of coa�ngs.

Government First Ar�cle Preproduc�on approval required. Tes�ng will be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE

TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN

THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR

HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM),

THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM

DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON

STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS

OF THE UNDIMENSIONED DRAWING.

THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR

DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE

DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE

INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND

(+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-)

0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH

DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO

WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY.

REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED

TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY.

SHELF-LIFE:

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

RS058: Shelf life requirement RS001 for a TYPE 2 (CODE 6) item with a shelf life of 24 month (extendable) applies to this item.

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 3-52915-501

IAW REFERENCE DRAWING NR 76823 3-52915

REVISION NR J DTD 01/24/2013

IAW REFERENCE DRAWING NR 76823 3-52915

REVISION NR J DTD 02/16/1972

PART PIECE NUMBER: 3-52915-501

IAW REFERENCE DRAWING NR 98747 3-52915

REVISION NR DTD 09/23/2020

IAW REFERENCE DRAWING NR 76823 3-52915/1

REVISION NR DTD 08/31/1960

IAW REFERENCE QAP 13873 SQAP-007398343

IAW REFERENCE DRAWING NR 13873 EI-007398343

*** Product Number: 008913601

TANK,FUEL,AIRCRAFT

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in be in accordance with applicable drawings, specifica�ons and/or

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N FCD47944

IAW REFERENCE DRAWING NR 71379 9900072

REVISION NR H DTD 03/27/1973

IAW REFERENCE DRAWING NR 71379 9900072

REVISION NR H DTD 03/20/1973

PART PIECE NUMBER: 9900072-1

IAW REFERENCE DRAWING NR 71379 CES2033

REVISION NR B DTD 09/13/1963

IAW REFERENCE DRAWING NR 13873 EI-008913601

IAW REFERENCE QAP 13873 SQAP-008913601

*** Product Number: 009816138

** PID Text

TANK,FUEL,AIRCRAFT T-38 MAIN

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

SHELF LIFE APPLIES:

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

1.SEE ENGINEERING DATA REQUIREMENTS UNDER DRAWING: 8016358-EI-009816138

IN DMS.

2. LABEL UNIQUE IDENTIFICATION (UID)REQUIRED:

the enclosed/referenced IUID technical requirements and MIL-STD-130.

DFARS 252.211-7003 clause applies.

DRAWINGS: ARE UNDER:

6122224-200925111

6478801-200925111 IN DMS

3. W/ E'OS 13C0210-H,07A0407-H, 98C0889-H.

THE REQUIRED EXPERIENCE AND CAPABILITY. FAILURE OF THIS ITEM COULD

RESULT IN LOSS OF AIRCRAFT AND CREW PERSONNEL.

THEREFORE, NEW SOURCES MUST BE APPROVED BY THE COGNIZANT SYSTEM ENGINEER

PRIOR TO CONTRACT AWARD.

A TECHNICAL DATA PACKAGE IS AVAILABLE AND MAY

BE OBTAINED FOR USE IN DEVELOPING A SOURCE

APPROVAL REQUEST (SAR) FOR ENGINEERING

SOURCE APPROVAL. TO OBTAIN A COPY OF THE

TECHNICAL DATA PACKAGE (TDP), CALL TECHNICAL

DATA MANAGEMENT CUSTOMER SERVICE

Website: htps://www.pdmd.dla.mil/cs/

(804)279-3477

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

MARK AS "FIRST ARTICLE.

DO NOT SEND TO SUPPLY.

OO-ALC/809 MXSS/MXDEB

BLDG 849 ATTN: NON-ACCOUNTABLE BAY

HILL AIR FORCE BASE, UT 84056-5713

PLEASE ENSURE THE WORDS 'FIRST ARTICLE' ARE MARKED ON THE OUTSIDE OF THE

BOX IN LARGE CONSPICUOUS LETTERS.

NORTHROP GRUMMAN SYSTEMS CORPORATION 79U29 P/N 3-52900-1

MEGGITT (ROCKMART), INC. 56221 P/N 320-51691-103

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 7C101-02271-1

IAW REFERENCE DRAWING NR 76823 3-52900

REVISION NR H DTD 01/24/2013

IAW REFERENCE DRAWING NR 76823 3-52900

REVISION NR H DTD 08/08/1972

PART PIECE NUMBER: 3-52900-1

REVISION NR E DTD 10/19/2012

REVISION NR E DTD 06/21/2018

IAW REFERENCE DRAWING NR 13873 009816138-18180

REVISION NR DTD 06/29/2018

IAW REFERENCE DRAWING NR 13873 EI-009816138

REVISION NR DTD 06/28/2023

*** Product Number: 010389880

** PID Text

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

Engineering instruc�ons. The first ar�cle offered shall be manufactured at the facili�es in which produc�on quan��es are procured and produced under this contract. When submi�ng the first ar�cle(s) for government tes�ng, a copy of the contract and all applicable drawings, specifica�ons, engineering instruc�ons, cer�fica�ons, and inspec�on sheets shall be provided. Upon receipt and evalua�on of the test report from the responsible government tes�ng loca�on, the contrac�ng officer will provide final no�fica�on to the manufacturer. Any ques�ons or concerns regarding

EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contras�ng color to the packaging. Marking shall be located adjacent to

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N 47500-503

AMERICAN FUEL CELL AND COATED FABRICS 05476 P/N FCR58207

REVISION NR G DTD 10/17/1978

PART PIECE NUMBER: 14-52901-503

REVISION NR G DTD 03/17/1998

IAW REFERENCE DRAWING NR 13873 EI-010389880

IAW REFERENCE QAP 13873 SQAP-010389880

*** Product Number: 010447141

** PID Text

TANK, FUEL, AIRCRAFT

*************** CRITICAL APPLICATION ITEM ******************

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

RQ039: Non-Tailored Higher-Level Quality Requirements (SAE AS9100) for

Manufacturers and Non-Manufacturers

PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION

CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN

THE "14 NORTHROP GRUMMAN CORP

T-38, F-5" LICENSE AGREEMENT FOLDER AVAILABLE AT

htps://pcf1x.bsm.dla.mil/cFolders

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

(ITAR) or the Export Administra�on Regula�ons (EAR), and cannot be exported without prior authoriza�on from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and na�onals whether located in the United

States or abroad. This requirement applies equally to foreign na�onal

Cer�fica�on Program (JCP) cer�fica�on, have completed the

Introduc�on to Proper Handling of DOD Export-Controlled Technical Data

Training and the DLA Export-Controlled Technical Data Ques�onnaire

(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instruc�ons for obtaining access to the been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in

MATERIAL REFERENCE NUMBER__ 18-52901-1

******** ENGINEERING DATA LIST DTD 31 AUG 2015 REV 3 *******

DWG: 18-52901, W/EO 98C0533

DWG: 14-00933, W/AP A,K

DWG: P-234

THE CONTRACTOR SHALL USE THE MOST CURRENT AMENDMENTS APPLICABLE TO EACH

DRAWING, MIL SPEC, MIL STD, INDUSTRY SPEC OR INDUSTRY STD AS OF THE

EFFECTIVE DATE OF THIS CONTRACT UNLESS OTHERWISE NOTED.

***** ENGINEERING DATA REQUIREMENTS DTD 31 AUG 2015 *****

(ATTACHMENT "A")

NOTES: 1-3 NOT APPLICABLE

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF

THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO

INDICATED.

5. MARKING PER MIL STD-130.

6. THIS ITEM IS A CRITICAL APPLICATION COMPONENT. THE STRUCTURAL AND

FUNCTIONAL INTEGRITY OF THIS ITEM CAN BE AFFECTED BY INDIVIDUAL

MANUFACTURES PROCESSES AND TECHNIQUES.

7. TO ENSURE CONTINUED PRODUCT INTEGRITY OF THE ITEM, PROCUREMENT IS

RESTRICTED TO APPROVED SOURCES LISTED ON THE SCREENING ANALYSIS

WORKSHEET. THESE SOURCES ARE KNOWN TO HAVE THE REQUIRED EXPERIENCE AND

CAPABILITY TO MANUFACTURE THIS ITEM.

8. FAILURE OF THIS ITEM COULD RESULT IN LOSS OF AIRCRAFT AND CREW

PERSONNEL; THEREFORE, NEW SOURCES MUST BE APPROVED BY THE ESA PRIOR TO

CONTRACT AWARD.

9. ALL WAIVERS/DEVIATIONS MUST BE SUBMITTED TO DSCR CONTRACTING OFFICER,

COORDINATED THROUGH DSCR TECH/QUALITY WITH CONCURRENCE…