Product Description Sweat Suits 20 Jan 2010.rtf
RTF text file 17 MB Posted
- Attached to
- Men's Sweat Suits
- Solicitation number
- FA7000-11-T-0016
About this file
Attachment 1 - Purchase Description 185 10LGR/LGRI Sweat Suits
Text of this file
UNITED STATES AIR FORCE ACADEMY
PURCHASE DESCRIPTION 185
10LGR/LGRI
SWEAT SUIT, CADET
20 January 2010
UNITED STATES AIR FORCE ACADEMY PURCHASE DESCRIPTION
I. SWEAT SUIT, CADET
A. Scope
This purchase description covers a two-piece silver gray sweat suit in a heavy weight cotton/polyester fabric; to be worn by cadet personnel at the United States Air Force Academy, see Figure 3 & 4.
B. First Article
Before production is commenced the contractor shall submit to the contracting office for quality control evaluation approval a First Article. One sweatshirt size large (L), and one pair of sweat pants size large (L) complying with the salient characteristics described in this purchase description, shall be submitted to the contracting office for evaluation after the awarding of the contract and prior to the beginning of production. The First Articles shall be constructed, in the requested color and fabric as described by this purchase description. First articles may be tested for compliance to this specification.
II. SWEAT SHIRT
A. Fabric
Base Sweatshirt Fleece Fabric - Extra heavy 90 % preshrunk cotton, 10% polyester, reverse weave, sweatshirt fleece. Fiber blend may vary with +5% in either the cotton percent or polyester %, with the understanding that the variance shall be +5%, only. Variation of weight may range from 11.0 to 12.0 oz per square yard. These variations are acceptable with the understanding that the minimum weight shall be 11. oz per square yard. Shrinkage may not exceed 6%.
Note: The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract.
Rib Knit Fabric - The rib trim is 1 X 1 cotton/polyester or cotton/nylon. Due to fabric manufacturing, the variation is from 90%/10% to 99%/1% cotton polyester or cotton/nylon; either one is acceptable. Up to 10% spandex is acceptable as long as cotton content is at least 90% of composition.
B. Thread
A three ply thread made of 90% cotton, 10% polyester shall be used. Alternately, two-ply polyester cord, polyester wrapped or 100% spun polyester will be acceptable.
C. Design
1. Hood: The hood shall be a double thick attached hood made of ribbed material with brass grommets for a drawstring. The drawstring shall be 60 inches long, 100% cotton, rounded of appropriate weight with a white barrel lock to hold it in place.
2. Sleeves: The Sweat shirt shall have set in sleeves.
3. Cuffs/Waistband: The shirt shall have ribbed cuffs, waistband, and action side inserts. The rib trim is 1 X 1 cotton/polyester or cotton/nylon. Due to fabric manufacturing, the variation is from 90%/10% to 99%/1% cotton polyester or cotton/nylon; either one is acceptable. Small amounts of spandex content are acceptable.
4. Muff Pockets: The muff pockets will vary among shirt sizes. The large size muff pocket shall be 15" at the bottom, 12" at the top, 10" high, and 7" opening, with a +¼" tolerance on any measurement, see figure 1. The contractor shall grade the size of the pocket according to Table 1 below.
Table I Cadet Muff Pockets Finished Measurements
Measurement S M L
XL
XXL
XXXL
Bottom of pocket Tolerance: +1/2" 14" 14" 15" 17" 18" 20" Top of pocket Tolerance: +1/2" 11" 11" 12" 13" 14" 15" Height Tolerance: +1/2" 10" 10" 10" 11" 12" 13" Opening Tolerance: +1/4" 7" 7" 7" 8" 9" 10"
5. Silk-Screening: Lettering shall be screen printed into the garment with silver gray light retro-reflective ink. The letters shall be block style letters 4" in height and 13 ½" long, measured at the bottom of the letters. The letters shall be centered on the front of the shirt +3/8", see Figure 1. The chevron design on the back shall be screen printed into the garment with silver gray light retro-reflective ink. The width of the chevron shall be 2" wide, and shall be placed to scale with a gap 1/8" to 5/8" from the top of the shoulder, see Figure 2. The retro-reflective stripe shall not go into the sleeve seam. The ink shall be bonded to the fabric so that reflective quality remains for the normal life of the product.
6. Color: The color shall be silver gray; also described as ash or birch.
D. Sizes:
The sizes shall be standard commercial sizes Extra Small (XS), Small (S), Medium (M), Large (L), Extra Large (XL), Extra, Extra Large (XXL), Extra, Extra, Extra Large (XXXL). For finished measurements see Table II.
Table II Cadet Sweat Shirt Finished Measurements Measurement
XS
S M L
XL
XXL
XXXL
Chest (1/2) Tolerance: +1/2" 23 ½ 26 ½ 29 ½ 32 ½ Sleeve Length Tolerance: +1/2" 38 ½ 41 ½ Back Length Tolerance: +1/2" Across Shoulder Tolerance: +1/4" 19 ¼ 20 ¼ 21 ¼ 22 ¼ 23 ¼ 24 ¼ 25 ¼ Hood Height Tolerance: +1/4" 16 ¾ 17 ¼ 17 ½ 17 ¾ 18 ¼ Hood Width Tolerance: +1/4" 10 ½ 11 ½ 12 ½
Measuring: All measurements shall be done with the garment laying flat on a surface.
Chest: Measure across the front of the sweatshirt level with the underarm area.
Sleeve Length: Measure from center back, around the neck, across shoulder, down the sleeve to include the cuff.
Back Length: Measure from center back down to the bottom hem, to include the rib waistband.
Across Shoulder: Measure from one side of the armhole seam, along the shoulder seam, across the neck, to the other armhole seam.
Hood Height: Fold hood in half and measure at front of the hood, starting from bottom to the top.
Hood Width: The hood width shall be measured 7" down the top, front of the hood when folded.
III. SWEAT PANTS
A. Fabric
Extra heavy 90 % preshrunk cotton, 10% polyester, reverse weave, sweatshirt fleece. Fiber blend may vary with +5% in either the cotton percent or polyester %, with the understanding that the variance shall be +5%, only. Variation of weight may range from 11.0 to 12.0 oz per square yard. These variations are acceptable with the understanding that the minimum weight shall be 11oz per square yard. Shrinkage may not exceed 6%.
Note: The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract.
B. Thread
Three ply thread made of 90% cotton, 10% polyester shall be used. Alternately, two-ply polyester cord, polyester wrapped or 100% spun polyester will be acceptable.
C. Design
1. Waistband: The sweat pants shall have an elastic waistband with a drawstring cord with a barrel lock. The drawstring opening shall be enforced using brass grommets. The drawstring shall be 100% cotton of appropriate weight shall be at least 60" long. The barrel lock for the waist drawstring shall be white plastic, adjustable, and shall prevent the drawstring from pulling into the waist tunnel. The leg bottoms shall also have elastic bottoms. The width of the elastic waistband shall be 1-1/2" wide.
2. Crotch: The sweat pants shall have an extended crotch gusset. The gusset shall be 3-1/4" in width and 8" in length, with a tolerance of 1/4".
3. Hems: The pants shall have elasticized leg bottoms with the elastic being ½" wide.
4. Silk-Screening: The inverted chevron design on the lower half of the leg will be silk-screened with silver gray light retro-reflective ink and shall be 2” wide. The silk-screening shall be placed approximately 10" up from the bottom of the leg +3/8". The point of the chevrons shall be in the center front and center back of the leg. The distance from the point of the chevron to the bottom shall be 8" + ¼". The stripe shall be aligned at the inseam + ¼". See figures 3 and 4. The outside leg needs to be a continuous screening. The ink shall be bonded to the fabric so that reflective quality remains for the normal life of the product.
5. Color: Color shall be silver gray.
D. Sizes
1. Sizes shall be standard commercial sizes Extra Small (XS), Small (S), Medium (M), Large (L), Extra Large (XL), Extra Extra Large (XXL) and Extra Extra Extra Large (XXXL). For finished measurements see Table III.
Table III Cadet Sweat Pants Finished Measurements
Measurement S M L
XL
XXL
XXXL
Waist Relaxed (1/2) Tolerance: +1/2" Hip/Seat (1/2) Tolerance: +1/2" Thigh (1/2) Tolerance: +1/2" Inseam Tolerance: +1/2" Bottom (1/2) Tolerance: +1/4" 5 ¾ 6 ½ 7 ¼
Measuring: All measurements shall be done with the garment laying flat on a surface.
| Waist Relaxed: Fold pants in half at the side seams and measure ½ of waist. |
| Hip/Seat: Measured with the pants folded in half at the side seams, 10" from the top of the waistband. |
| Thigh: The thigh shall be measured at the leg area of the pants. Fold pant in half at the side seams and measure, 1" below the extended gusset found at the crotch area. |
Inseam: The inseam shall be measured from the lower edge of the seat seam at the extended gusset, to the bottom leg hem, (The gusset is not measured).
Bottom: The bottom of the pants shall be measured relaxed with the pants folded in half at the side seams.
IV. OTHER REQUIREMENTS
A. Instruction Label
1. Standard labels shall be placed in all garments giving size, care instructions and manufacturer name. A Code 39 bar code label shall also be affixed to the individual garment package. The Code 39 bar code shall be a removable paper ticket of commercial quality with the USAFA 10ABW/LGLC stock number and Code 39 bar code. The paper ticket shall contain a short item description to include size in plain text.
B. Patterns.
A master pattern in size medium will be furnished by the Government. The patterns provide for a 3/8” seam allowance for all seams unless otherwise specified here-in. The standard patterns shall not be altered in any way, and are to be used as a guide for cutting the contractor’s working patterns. The working patterns shall be identical to the standard pattern. The contractor shall have the ability to develop and grade working patterns to all sizes required by the procuring activity.
C. Regulatory Requirements
The contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).
1. Flammability Requirements: The basic material shall conform to the rules and regulations of the Flammable Fabrics Act without the application of a flame retardant finish to the material or to the end item.
2. Workmanship: The finished Sweat suit outfit shall conform to the quality of product established by this document. The occurrence of defects shall not exceed the contractor’s own quality assurance standards and the quality assurance standards defined by this purchase description and the technical data in the bid package.
3. Certification: The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producer’s own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Reliance on contractor quality assurance systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract.
4. Certification of Compliance: Unless otherwise specified in the contract or purchase order, certificates of compliance shall be requested by government on all components, if the government deems necessary.
5. Inspection: The contractor shall inspect the finished products 100% for compliance with this purchase description prior to submitting to the USAFA for final inspection by 10 MSG/LGRI Quality Control personnel.
6. Final Inspection: The point of final inspection and acceptance of the finished articles shall be at the USAF Academy, using ANSI/ASQC Z1.4-1993 and this purchase description.
D. Inspection Levels And Acceptable Quality Level
1. Inspection levels and acceptable quality levels (AQL’s) expressed in defects per hundred units (DHU) shall be in accordance with ANSI/ASQC Z1.4-1993. To get an accurate understanding of defects per hundred the inspector shall follow ANSI/ASQC Z1.4 Inspection Levels and it’s instructions. To obtain a copy of ANSI/ASQC Z1.4 call: American National Standard, at 1-800-854-7179 or write to: American Society for Quality Control, 611 East Wisconsin Avenue, Milwaukee, WI 53202.
3. AQL levels and inspection levels for defects listed in Table IV and V (General and Detailed Defects, and Silk Screening Defects):
AQL
INSPECTION
LEVEL
LEVEL
Major 2.5
II
Major and Minor A 15.0
II
Major, Minor A and 40.0
II
Minor B (combined)
For defects listed in Size and Measurement, Table I, II, and III:
One Class 4.0 S-3
TABLE IV. GENERAL AND DETAILED DEFECTS
MINOR
MAJOR
A B A Inferior material or workmanship defects such as distortion due to fabric manufacturing: slubs, thread breaks, holes, cuts, or any defect on the fabric attributed to the manufacturing of the fabric.
X
B Component and assembly - any component part or required operation omitted or not performed in accordance with specification. Includes but not limited to poor serging, stitching, and misalignment of components.
C
Defects such as holes, cuts, and or tears due to workmanship qualities or fabric quality.
D Loose thread, ends not removed, or instruction label miss printed.
E Discoloration, stains or spots due to material or workmanship
F Color not conforming to the color specified
G Incorrect, or illegible measurements. Inspection will be scored using the Size & Measurement Table I, & II, and III.
H Missing Instruction Label or Code 39 Bar label. Bar code 39 not scannable and or not readable by government system
TABLE V. SILK SCREENING DEFECTS
I Alignment of USAFA, or chevrons off centered, backwards, or misaligned.
J USAFA, or chevron missing, or not conforming to Figure 1, 2, 4, or 5.
K Smudging, or misprint such as double print, ghost images, or blurry prints
L Bad ink, thick and thin areas
E. Preservation, Packing, and Marking: The preservation, packing, and marking shall be as specified in the contract or order.
F. Source of Government Documents: Copies of military and Federal documents available from:
Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094
G. Source of non-Government Documents:
1. ASTM Test Methods: Applications for copies should be addressed to American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.
2. AATCC Test Method: Application for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), PO Box 12215, Triangle Park, NC 27709-2215.
4. Sample. For access to standard sample for shade, address the contracting activity issuing the invitation for bid.
CUSTODIAN
USAF Academy, CO 80840-8210
PREPARING ACTIVITY
Cadet Uniform, 10LGRCU
REVIEWING ACTIVITY
Flight Chief, 10LGRC Cadet Logistics Flight
12” Sweatshirt front and pocket file_0.wmf
Sweathshirt back chevron file_1.wmf file_2.png file_3.wmf
Figure 3.
file_4.png file_5.wmf
Figure 4.
file_6.png file_7.wmf
Figure 5.
Other files
| File | Type | Posted |
|---|---|---|
| Past Performance Survey Sweat Suits.doc | DOC document | |
| Amendment Solicitation Sweat Suits.pdf | ||
| Bar Code Sample.pdf | ||
| First Article Approval FAR 52.209-4.docx | DOCX document | |
| Solicitation Sweat Suits.doc.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
File details come from the government source that posted it. Updated .