DD_1423_and_Data_Item_Description_(DID).pdf

CONTRACT DATA REQUIREMENTS LIST Form Approved ( 1 Data Item) 0MB No. 0 704-0188

The public reporting burden for t his collection of information is estimated to average 110 hours per response, including the time for re viewing instructions, searc h ing existing data sources , gathering and maint ain ing the data needed , and completing and reviewing the collection of information. Send co mments regarding t his burden est imate or any other aspect of this co llection of in fo rmation , including suggestions for reducing t he burden, to the Department of Defense , Executive Services and Communications Directorat e (0704-0 188). Respondents should be aw are that notw it hstanding any other provision of law, no person sha ll be subject to any penalt y fo r fa iling t o comp ly w ith a collection of info rmation if it does not display a c urrently v al id 0MB control number. Please do not return your form to the above organization. Send completed form to the Government Iss uing Cont rac.t ing Officer fo r the Contract/PR No . listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

A(FY 19) TDP TM X OTHER --- --

D. SYSTEM/ITEM I E. CONTRACT/PR NO. F.CONTRACTOR

CCG 715 - Dual Axis Angle Generator

1. DATA ITEM NO. 2 . TITLE OF DATA ITEM 3 . SUBTITLE

AOOI AOO I Technical Manual Contract Requirements (TMCR)

4. AUTHORITY (Data Acquisition Document No.) , 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

TM-86-01 SOW 19C-234A-OP Atch AFLCMC/WNMM 7 . DD 250 REQ 9. DIST STATEMENT 10. FREQUENCY 12. DATE OF FIRST SUBMISSION 14. DISTRIBUTION

NIA

REQUIRED ASREQ See BLK 16 b. COPIES

8 . APP CODE 11 . AS OF DATE 13. DATE OF SUBSEQUENT a. ADDRESSEE Final

NIA D

ASREQ

SUBMISSION Draft See BLK 16 Reg Repro

16. REMARKS

BLK 8: The Government has 30 calendar days to review the preliminary draft. The I. AFMETCAL contractor has 10 calendar days after receipt of Government comments to prepare Attn: Tom Carson and deliver revised data. Criteria for approval shall meet the Government 813 lrving Wick Dr., W. Horton Building comments. Reference the contract number in all correspondence. Heath. OH 43056

BLK 9: The following statement shall be included on the manuals:

DISTRIB UTION STATEMENT D: DoD and US DoD contractors only

Blk 13: Concurrent with delivery of production units contractor shall furnish and Ship with unit 1 pack one (1) set of the manuals with each unit. Manual shall be on CD/DVD in indexed Portable Document Format (iPDF). Ship with unit.

15. TOTAL 0 1 0

G. PREPARED BY H. DATE I. APPROVED BY J. DATE

CAPUANO.FRAN Digitally signed by SKINNER.KEVIN ~~,'~·~~~~;;i,~,\ 11 102•22122 CAPUANO.FRANK.R.140320965 2/6/ 19 2/6/19 K. R.1403209658 8 . L.11 .1024227223 3

Date: 2019.02.06 12:18:18-05'00' Date: 2019.02.06 12: 19:28-05'00' . , DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED. Page of 1 Pages

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

Attachment 2

TM-86-01Q 27 Oct 2017 1-01: AF TMSS Linear TMs

Air Force Technical Manual Contract Requirements (TMCR) for

AIR FORCE CALIBRATION AND METROLOGY (AFMETCAL) PROGRAM

CCG 715 - Dual Axis Angle Generator

ATTACHMENT DD FORM 1423, TO CDRL SEQUENCE NUMBER 001, EXHIBIT A REQUEST FOR

PROPOSAL/CONTRACT:

Date: 16 January 2019

SECTION 1. TECHNICAL ORDER (TO) PROGRAM REQUIREMENTS

1. TMCR Tailoring. This TMCR has been tailored by the program office, including the associated tables, matrices and Specification/Standard Interface Records (SIRs). The Contractor may propose and submit, in writing, additional tailoring to the Technical Order Manager Agency/Agent (TOMA), Government Program Manager (PM), and Procuring Contracting Officer (PCO) for consideration. The tailored TMCR shall be attached to the Contract Data Requirements List (CDRL) for Technical Order (TO) delivery, and shall be included in the proposal as a separate exhibit, referenced in the proposal Statement Of Work (SOW). Air Force (AF) TO Acquisition procedures, including procedures for tailoring this document, are found in TO 00-5-3, AF Technical Order Life Cycle Management, located at http://www.tinker.af.mil/Home/TechnicalOrders.aspx. A copy may also be obtained from the Program TO Manager. Any terms or procedures found in this document may be researched there.

2. TO Program Scope. The Contractor shall develop and deliver technical manuals in accordance with (IAW) this TMCR that supports the AFMETCAL requirements for technically usable manuals. The technical manuals will include Operation and Maintenance Instructions, Illustrated Parts Breakdown, and Calibration Process/Procedure in a Portable Document Format (PDF). PDF TO Publications may be produced and distributed as physical media (Paper/CD) or electronically via Enhanced Technical Information Management System (ETIMS) electronic TO Viewer (eTOV).

3. Commercial Manuals. Contractors shall recommend the use of existing commercial manuals to the maximum extent possible without impairing program support objectives. All proposed commercial manuals are subject to Government review and approval. Contractors shall use Data Item Description (DID) DI-TMSS-80067C, Technical Manual (TM) Contractor Furnished Aeronautical Equipment or Contractor Furnished Equipment (CFAE/CFE) Notices, to provide recommendation data. A copy is available through ASSIST at http://quicksearch.dla.mil/qsSearch.aspx.

3.1. The AF requests the ability to electronically store, print, distribute, update and decollate the commercial manual to allow for printing. Commercial manuals shall be delivered as Portable Document Format (PDF) unless otherwise specified.

3.2. Approved Commercial-Off-The-Shelf (COTS) Manuals shall be delivered with an Identifying TO Publication Sheet (ITPS), IAW MIL-PRF-32216, Performance Specification: Evaluation Of Commercial Off-The-Shelf (COTS) Manuals And Preparation Of Supplemental Data. All PDF files of commercial data shall be non-password protected to allow the AF to decollate the manual for printing.

Attachment 2 http://www.tinker.af.mil/Home/TechnicalOrders.aspx http://quicksearch.dla.mil/qsSearch.aspx

3.3. If the proposed COTS data is found to be insufficient after review by the Government, the Contractor shall prepare supplemental data for the COTS manual as required IAW Military Standard (MIL-STD)-38784. If the COTS data cannot be supplemented sufficiently the Contractor may be tasked to develop new TM data IAW the applicable TMSS listed in Section 2, Table 1.

4. Technical Manual Specifications and Standards (TMSS) Tailoring. The contractor shall develop all TMs IAW most current version of applicable TMSS for the type manual being developed and comply with the Specification/Standard Interface Records (SIRS) provided within Section 3.

5. Subsequent TO/Data Requirements. (Deleted)

6. TO Development. TOs shall be written to a scope and depth of coverage to support the AFMETCAL operations and maintenance concepts.

6.1. Standard Generalized Markup Language (SGML) tagged TO files shall include required illustration (graphics) files in an approved graphics exchange format. Illustration files developed and delivered for other purposes shall be used in lieu of developing special TM illustration files whenever possible. All delivered graphics shall conform to the approved graphic creation and format guidelines listed in Attachment 1, Graphics Format Guidelines. For assistance with illustration requirements contact AF TMSS via (e-mail: SGMLSupport@us.af.mil).

6.2. (Deleted)

7. TO Numbering. (Deleted)

8. Data Rights. Contractors shall comply with 10 U.S.C. 2320 and cognizant Defense Federal Acquisition Regulation Supplement (DFARS) provisions and clauses in providing Unlimited Rights for all source data, TO publications, and TO updates prepared specifically for the contract. Government rights in data are specified in the DFARS, 252.227-7013, Rights in Technical Data, Noncommercial Items, 252.227- 7014, Rights in Noncommercial Computer Software and Noncommercial Computer Software Documentation, and 252.227-7015, Technical Data-Commercial Items. The Government shall be given Unlimited Rights for all Government-funded business rules (tailoring and application methods and procedures) and documented business processes developed under the contract for the purpose of TO development. For all data delivered to the Government with other than Unlimited Rights, the Contractor shall assert their data rights IAW DFARS 252.227-7017, Identification and Assertion of Use, Release, or Disclosure Restrictions. The Contractor shall pass through and enforce all requirements in this TMCR to all sub-Contractors.

9. Classification, Distribution, Destruction, Disclosure, Export Control Notices, and Cyber Security.

Contractors shall recommend the correct markings and controls for classified and restricted distribution data and TOs IAW the program’s Security Classification Guide (SCG) and Department of Defense Manual (DODM) 5200.01, Department of Defense Instruction (DODI) 5230.24, Department of Defense Directive (DODD) 5230.25, Air Force Instruction (AFI) 16-1404, and MIL-STD-38784 (available at http://www.e-publishing.af.mil/ or https://assist.dla.mil/online/start/index.cfm). The markings and notices shall be reviewed during In-Process Reviews (IPR). The Contractor shall also apply policy and procedures for Cyber Security Protection IAW AFI 33-200, Information Assurance (IA) Management, AFMAN 17-1301, Computer Security (COMPUSEC), and MPTO 00-33B-5008, Remanence Security for Information Systems. NOTE: Distribution limitations will be determined on a case-by-case basis as TOs are developed, dependent upon TO content.

Attachment 2 mailto:SGMLSupport@us.af.mil http://www.e-publishing.af.mil/ https://assist.dla.mil/online/start/index.cfm

10. TO Quality. Contractor proposals shall describe how the Government will be allowed to interact with the Contractor’s TO development team. The Contractors shall ensure prepared TOs are: a) technically accurate and safe; b) written to a scope and depth of coverage to support the operations and maintenance concepts; c) properly classified and marked with export control and distribution limitation statements.

11. TO Delivery. TO file delivery requirements are located in Section 2, Table 3 of this document.

11.1. MIL-SPEC (SGML) Tagged Files. The Contractor shall parse all SGML files required for the TOs prior to Government delivery and shall verify the SGML is compliant with the appropriate DTD.

NOTE: The Government will parse the files prior to acceptance using the public domain SGML parser (http://www.jclark.com/sp/).

12. Source Data Maintenance. (Deleted)

13. TO Maintenance. (Deleted)

14. Schedules. (Deleted)

15. Time Compliance Technical Orders (TCTOs). (Deleted) http://www.jclark.com/sp/

SECTION 2. TM TYPE AND DELIVERY REQUIREMENTS

NOTES:

• Mark the TM Type Selection Tables indicating the applicable TO types and related specifications.

(NEW DEVELOPMENT) LINEAR TM TYPE (PUBLICATION) SELECTION TABLES.

TABLE 1

TMSS REQUIREMENTS FOR THE AFMETCAL

(CCG 715 -Dual Axis Angle Generator)

Title or Type of Manuals Specification Required

1. Inspection TOs MIL-DTL-5096

a. Inspection and Maintenance Requirements (-6) Manual

b. Acceptance and Functional Check Flight (FCF) Procedures (-6CF)

Manual

c. Acceptance and Functional Check Flight (-6CL) Checklist

d. Inspection Workcards (-6WC)

e. Maintenance/Operations Checklists

2. Cargo Aircraft Loading and Offloading TOs MIL-DTL-5288

a. Loading Instructions Manual

b. Nuclear Weapon Cargo Loading Manual

c. Checklists

3. Weight and Balance (Aircraft) MIL-DTL-5920

a. Loading Data Manual

b. Sample Basic Weight Checklists

4. Flight Manuals MIL-DTL-7700

a. Flight Manual

b. Performance Data Manual

c. Mission Crew Manual

d. Supplemental Manual

e. Abbreviated Flight Crew Checklist

5. List of Applicable Publications MIL-DTL-8031

6. Structural Repair Manuals (for Aircraft) MIL-DTL-9854

7. Munitions/Weapons Loading Procedures, Non- nuclear and Nuclear TOs MIL-DTL-9977

a. Nuclear Weapons Basic Information and Loading Procedures

b. Nuclear Weapons Loading Procedures

c. Non-nuclear Munitions Basic Information

d. Non-nuclear Loading Procedures

e. Non-nuclear Munitions Loading Standard Data Packages (SDPs)

f. Loading Procedures Checklist

g. Single Loading Procedures Checklist

h. Integrated Loading Procedures Checklists

i. Family Group Loading Procedures Checklist

j. Nuclear Weapons Loading Procedure Checklists

k. Functional Check Procedures Checklist

l. NATO Stage B Cross-Servicing Checklists

m. End of Runway (EOR) Procedures Checklist

8. Space Operations and Support Documentation TOs

TABLE 1

TMSS REQUIREMENTS FOR THE AFMETCAL

(CCG 715 -Dual Axis Angle Generator)

Title or Type of Manuals Specification Required -- MIL-SPEC (Intercontinental Ballistic Missiles) -- MIL-SPEC (Space)

MIL-PRF-38311

MIL-PRF-38314

a. Operations Manual

b. Operations Checklists

c. Technical Manuals and Related Checklists

9. Nuclear and Non-nuclear Weapon Delivery and Aircrew Procedures Manuals and Checklists

MIL-DTL-38384

a. Non-nuclear Weapon Delivery Manual

b. Aircrew Nuclear Bomb Delivery Manual (Strategic Bomber Aircraft)

c. Aircrew Nuclear Missile Delivery Manual (Strategic Bomber Aircraft)

d. Aircrew Nuclear Bomb Delivery Manual (Tactical Aircraft)

e. Non-nuclear Weapon Delivery Checklist

f. Nuclear Weapon Delivery Checklist (Strategic Bomber Aircraft)

g. Aircrew Nuclear Bomb Delivery Checklist (Tactical Aircraft)

h. Non-nuclear Weapon Delivery Source Data Packages

10. Work Unit Code Manual

a. Standard WUC Manual

b. Two Chapter Manual

c. Three Chapter Manual

MIL-DTL-38769

11. Calibration Procedures MIL-DTL-38793

12. Time Compliance Technical Orders (TCTOs)

a. TCTO

b. TCTO Supplement

MIL-DTL-38804

13. Aircraft Battle Damage Assessment and Repair TOs MIL-DTL-87158

14. Illustrated Parts Breakdown MIL-DTL-38807

15. On-Equipment Organizational Maintenance Manual Set MIL-DTL-83495

a. General Equipment (GE) Manual

b. General System (GS) Manuals

c. Combined GE & GS Manual

d. Job Guide (JG) Manuals

e. Fault Reporting (FR) Manual

f. Fault Isolation (FI) Manual

g. Wiring Data (WD) Manual

h. Schematic Diagram (SD) Manual

TABLE 1

TMSS REQUIREMENTS FOR THE AFMETCAL

(CCG 715 -Dual Axis Angle Generator)

Title or Type of Manuals Specification Required

16. Operation and Maintenance Instructions in Work Package Format MIL-DTL-87929

a. Maintenance Manuals

(1) Organizational Maintenance

(2) Intermediate Maintenance

(3) Depot Maintenance

(4) Combined (I&D) Maintenance

(5) On Condition Maintenance

b. Operation & Maintenance Instruction Manuals

c. Special Manuals

(1) Aircraft Engine Testing and Trending Procedures

(2) Aircraft Power Package Testing Procedures

(3) Static Firing of Missile Motors

(4) System Peculiar Corrosion Control

(5) Nondestructive Inspection (NDI)

(6) Aircraft Structural Integrity Program (ASIP)

(7) ATE Operator Test Procedures

(8) Special Requirements for Storage and Maintenance Procedures;

AUR Munitions/Launchers and Associated Support Equipment, Conventional Components and CMBR Agents

(9) Parachute Packing Procedures

(10) Operators Instructions (Hand-Held Flight Computers)

(11) Installation-Engineering Facility (Ground C-E Equipment)

d. Checklists (IAW MIL-DTL-5096)

e. With Illustrated Parts Breakdown

17. Commercial Manuals (Evaluate according to MIL-PRF-32216)

18. Aircraft Cross-servicing Guide MIL-DTL-22202

TABLE 3 – LINEAR TM DELIVERY REQUIREMENTS

FOR THE AFMETCAL

CCG 715 -Dual Axis Angle Generator

NOTES:

• For Paper media delivery indicate required quantity

DELIVERY SCHEDULE

Event Number of days data required prior to event Technical Review(s)

( DACA)

First Article/First Production Unit

( DACA)

Administrative (Logistics)

DAFAOK)

Final TO Distribution (Ship With Prod Units)

(730

DACA)

Enter physical mailing address, electronic delivery location or web access point

Legend: DACA - After Contract Award DAFAOK - Days after First Article accepted (passes Acceptance testing)

Engineering (Draft) Copy AFLCMC/WNMRP/AFMETCAL Division ATTN: Tom Carson thomas.carson.2@us.af.mil 813 Irving Wick Drive West, Bldg 2 Heath, Ohio 43056

IPDF / IPDF / IPDF / IPDF /

First Production Copies (ship w/1st Prod.)

Bionetics Transportation ATNN: Carol Cooperrider 813 Irving Wick Drive West, Bldg 4, Door 15 Heath, Ohio 43056

IPDF / IPDF / IPDF / IPDF /

Administrative (Logistics) Copies AFLCMC/WNMRP/AFMETCAL Division ATTN: Tom Carson thomas.carson.2@us.af.mil 813 Irving Wick Drive West, Bldg 2 Heath, Ohio 43056

IPDF / IPDF / IPDF / IPDF /

Final (Production) Copies (ship w/ unit) Bionetics Transportation ATTN: Deanna Neece 813 Irving Wick Drive West, Bldg 4, Door 15 Heath, Ohio 43056

IPDF / IPDF / IPDF / IPDF / 1

Total Paper Copies Required: 1

SECTION 3. DELETED