F-15 Support Rack Steel Drawings.pdf

Part # Title Material Spec Qty (per set) Notes: Total Quantity 971069-01 W BEAM, WIDE FLANGE W8 x 24 lb/ft steel beam (8.00 x 6.5) ASTM A-36 1 8 971069-03 TUBE, RAIL 2 x 4 x 3/16 wall tube ASTM A-500, Grade B 1 8 971069-05 PLATE, BRACKET 1/4 thk plate ASTM A-36 8 64 971069-07 BRACE, LOWER 2 x 4 x 1/8 wall tube ASTM A500, Grade B 2 16 971069-11 BRACE, BOTTOM, END 2 x 4 x 1/8 wall tube ASTM A500, Grade B 2 16 971069-13 SUPPORT, VERTICAL 2 x 4 x 1/8 wall tube ASTM A500, Grade B 4 32 917069-15 BRACE, UPPER, CENTER 2 x 4 x 1/8 wall tube ASTM A500, Grade B 1 8 971069-17 BRACE, SUPPORT, -17 2 x 4 x 1/8 wall tube ASTM A500, Grade B 2 16 971069-21 BRACE, UNDER SUPPORT 2 x 4 x 1/8 wall tube ASTM A500, Grade B 2 16 971069-23 BRACE, BOTTOM CENTER 2 x 4 x 1/8 wall tube ASTM A500, Grade B 1 8 971069-25 BRACE, SUPPORT, -25 2 x 4 x 1/8 wall tube ASTM A500, Grade B 2 16 971069-27 GUSSET, LARGE 1/4 thk plate ASTM A-36 2 16 971069-31 GUSSET, SMALL 1/4 thk plate ASTM A-36 6 48 971069-33 PLATE, SUPPORT 1/4 thk plate ASTM A-36 4 32 971069-35 PAD, CASTER 1/4 thk plate ASTM A-36 4 32 971069-37 COVER, CAP, -37 16 GA (.059) thk HR steel sheet AISI C1008/C1010 8 64 971069-41 COVER, CAP, -41 16 GA (.059) thk HR steel sheet AISI C1008/C1010 1 8 971070-01 RELEASE PIN COLLAR 11 GA STAINLESS STEEL ASTM A240 4 Quote Flat part: 1.00 X 7.00 X 0.12 32 20173106-01 SHAFT Ø1/4, 17-4PH SS ASTM A693 4 Quote solid round only 32 20173106-03 HANDLE Ø1/4, 17-4PH SS ASTM A693 4 Quote solid round only 32

L. BRATTON 971228

1:8

NOTES:

1. INTERPRET DRAWING IAW ASME Y14.100 AND ASME Y14.5-2018.

2. REMOVE ALL BURRS AND SHARP EDGES.

3. WELD IAW ANSI/AWS D1.1/D1.1M-2020. UNLESS OTHERWISE NOTED, ALL JOINTS ARE TO BE WELDED WITH A CONTINUOUS FILLET WELD. THE SIZE OF THE FILLET WELD SHALL BE EQUAL TO THE THICKNESS OF

THE THINNEST PART BEING WELDED.

4. ALL DIMENSIONS APPLY BEFORE APPLICATION OF COATING.

5. BEFORE APPLICATION OF PAINT DRILL .25 DIAMETER WEEP/DRAIN HOLE THROUGH BOTTOM OF ALL

SEALED TUBES TO PERMIT CONDENSATION DRAINAGE.

6 CAP COVER, (FIND NO. 16) TO BE CENTERED ON TUBES (FIND NOS. 2, 5 & 9 AS SHOWN.

7 CENTER CAP COVER (FIND NO. 17) ON OPENING OF TUBE (FIND NO. 7) AND WELD AS SHOWN.

8 OPTIONAL TO WELD PLATES (FIND NO. 14) IN PLACE AND THEN CUT 4-INCH HOLES IN PLATE (FIND NO.

14) AND BEAM (FIND NO. 1).

9. PRIMER ALL EXTERIOR SURFACES AND EDGES IAW MIL-PRF-23377, TYPE II, CLASS C1, C2 OR N. PAINT ALL PRIMED SURFACES IAW MIL-PRF-85285, TYPE II, COLOR GRAY, COLOR NO. 26173 IAW FED-STD-595.

10. WORKMANSHIP:

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES, PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES, NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT, CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER. THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO ANY PART OR TO THE ENVIRONMENT, NOR SHALL ANY PART BE CONTAMINATED BY THE CLEANING

AGENT.

E. ZAMORSKI 980623

E. ZAMORSKI 980623

971068971068

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

E REDRAWN WITH CHANGE: CHANGED NOTE 8 TO

PROVIDE OPTIONAL FAB. ML 20210708 7/8/2021

-10 CAGE IDENTIFYING NO MATERIAL / SPECIFICATION ZONE FN

1 COVER, CAP -41 16 GA (.059) THK HR STEEL SHEET IAW AISI

C1008/C1010 4B6 17

8 COVER, CAP -37 16 GA (.059) THK HR STEEL SHEET IAW AISI

C1008/C1010 2A4 16

4 PAD, CASTER -35 1/4 THK STEEL PLATE IAW ASTM A-36 2A4 15

4 PLATE, SUPPORT -33 1/4 THK STEEL PLATE IAW ASTM A-36 4D2 14

6 GUSSET, SMALL -31 1/4 THK STEEL PLATE IAW ASTM A-36 2C7 13

2 GUSSET, LARGE -27 1/4 THK STEEL PLATE IAW ASTM A-36 2C7 12

2 BRACE, SUPPORT -25 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2C7 11

1 BRACE, BOTTOM CENTER -23 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2D6 10

2 BRACE, UPPER SUPPORT -21 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2D6 9

2 BRACE, SUPPORT -17 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2B7 8

1 BRACE, UPPER, CENTER -15 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2D4 7

4 SUPPORT, VERTICAL -13 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2C2 6

2 BRACE, BOTTOM, END -11 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2A3 5

2 BRACE, LOWER -07 2 X 4 X 1/8 WALL STEEL TUBE IAW ASTM A-500 GR B 2B2 4

8 PLATE, BRACKET -05 1/4 THK STEEL PLATE IAW ASTM A-36 2D5 3

1 TUBE, RAIL -03 2 X 4 X 3/16 WALL STL TUBE IAW ASTM A-500 GR B 2D4 2

1 W BEAM, WIDE FLANGE -01 W8 X 24 LB/FT STEEL BEAM (8.00 X 6.5) IAW ASTM A-36 2D7 1

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

A

D

C

B

A

1345678 2

U.S. AIR FORCE

APPLICATION

PARTS LIST

SHEETSCALE:

SIZE

TITLE

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

.03

.010 .5°

D

X971069-10_E

MATERIAL:

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

QUANTITY REQUIRED PER DASH NO.

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

EGLIN A.F.B. FL-

18894

D

C

B

A

D

C

B

A

1345678 2

U.S. AIR FORCE

APPLICATION

PARTS LIST

SHEETSCALE:

SIZE

TITLE

THIRD ANGLE PROJECTION

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

.03

.010 .5°

D

X971069-10_E

MATERIAL:

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 7 JULY 2021. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

X971069 E

STORAGE RACK WELDMENT,

F-15 PYLON

X9

E

2X 1.50 2X 1.50

2X 1.50 .25

2X 1.50

2X .88 2X .88

SECTION B-B

3B6

REF

REF

REF

REF

REF

REF

REF

REF

REF

143.50

.25

22.25 29.00 29.00 29.00

2X 1.88 4X 3.96

70.75

C

C

SECTION A-A

14 4X

SEE DETAIL -33

3C1

REF

REF

REF

REF 7A3

4X .25

SECTION C-C

SCALE 1 : 4

1 12

16 REF

REF

REF

REF

REF

.06 ALL AROUND

VIEW E-E

SCALE 1 : 4

17SEE DETAIL -41

3D8

REF

7B7

1:8

REF

REVISIONS

LTR DESCRIPTION DATE APPROVED

E SEE SHEET 1. 7/8/2021

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEETSCALE:

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X971069-10_E

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEET

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 7 JULY 2021. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

X9

X971069 E

3.97

29.00 29.00 29.00 4X 4.00

28.25

DETAIL -018 2D7

143.50

2.25 2.25

7.93 (STK)

6.49 (STK)

.40 (STK)

4X 3.12

2.00 (STK)

4.00 (STK)

"W " (STK) "L" DIM

2.02+ .03 .00

.99

.50

4.00

2.88

.50

.500+ .006 .001

4X .50 X 45°

2.00 2.00

1.25

2X R

10-24 UNC-2B

.25 (STK)

4.00 (STK)

2.00 (STK)

.13 (STK)

44.13

2.00

.88

DETAIL -15

SCALE: 1:2

2D4

TABLE A

DETAIL -05

1:8

SCALE: 1:2

2D5

REVISIONS

LTR DESCRIPTION DATE APPROVED

E SEE SHEET 1. 7/8/2021

DASH NO. "L" DIM "W" DIM

-03 143.50 .188 -07 139.00 .125 -11 72.00 .125 -13 59.00 .125 -21 50.37 .125 -23 47.12 .125

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEETSCALE:

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X971069-10_E

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEET

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 7 JULY 2021. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

X9

2.00 (STK)

4.00 (STK)

.13 (STK)

SCALE: 1:2

2B7

2X 45°

20.00

2X 45°

25.50

DETAIL -25

2.00 (STK)

4.00 (STK)

.13 (STK)

.25

.25

45°

10.00

10.00

.38 X 45°

.25 (STK)

.25

.25

45°

6.00

6.00

.38 X 45°

.25 (STK)

DETAIL -17

DETAIL -27

DETAIL -31

SCALE: 1:2

SCALE: 1:2

SCALE: 1:2

1:8

2B7

2B7

REVISIONS

LTR DESCRIPTION DATE APPROVED

E SEE SHEET 1. 7/8/2021

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEETSCALE:

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X971069-10_E

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEET

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 7 JULY 2021. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

X971069 E

X9

3.375

5.250 .875

5.13

7.00 4X R.38

4X .531+ .008 .001

.875

B

C

.25 (STK)

A

1.88

3.88

4X R.25

.06 (STK)

1.88

.75

2X R.25

.06 (STK)

6.00

3.56

12.00

7.13

4.00

.25 (STK)

DETAIL -35

DETAIL -33

DETAIL -37

DETAIL -41

SCALE: 1:1

SCALE: 1:1

SCALE: 1:2

SCALE: 2:1

1:8

2A4

4B6

2A4

2C2

.030 M A B C

REVISIONS

LTR DESCRIPTION DATE APPROVED

E SEE SHEET 1. 7/8/2021

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEETSCALE:

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X971069-10_E

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEET

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 7 JULY 2021. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

X9

1.00

4.00

.13 (STK) 15°

A

A

1.00 .50

.50 .250+ .005 .001

4X .25 X 45°

.188+ .005 .001

.38

.50

VIEW A-A

L. BRATTON 971228

1:1

E. ZAMORSKI 980623

E. ZAMORSKI 980623

971068971068

NOTES:

INTERPRET DRAWING IAW ASME Y14.100 AND ASME Y14.5-2018.1.

MATERIAL: 316 STAIN STEEL SHEET, 11 GAGE (.120).2.

REMOVE ALL BURRS AND SHARP EDGES3.

4. WORKMANSHIP:

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE

FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES, PITS,

VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES,

NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT

AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL

DIRT, CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN

MATTER. THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO

ANY PART OR TO THE ENVIRONMENT, NOR SHALL ANY PART BE CONTAMINATED BY

THE CLEANING AGENT.

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

C REDRAWN WITH CHANGE; REMOVED PART ID. 7/6/2021

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

A

D

C

B

A

1345678 2

U.S. AIR FORCE

APPLICATION

PARTS LIST

SHEETSCALE:

SIZE

TITLE

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

.03

.010 .5°

D

X971070_C

MATERIAL:

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

QUANTITY REQUIRED PER DASH NO.

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

EGLIN A.F.B. FL-

18894

D

C

B

A

D

C

B

A

1345678 2

U.S. AIR FORCE

APPLICATION

PARTS LIST

SHEETSCALE:

SIZE

TITLE

THIRD ANGLE PROJECTION

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

.03

.010 .5°

D

X971070_C

MATERIAL:

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 7 JULY 2021. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

X971070 C

RELEASE PIN COLLAR

X9

C

QUOTE 1.00 X 7.00 X 0.12 BAR (NO HOLES/CHAMFERS/BENDS)

2 2A5

12C5

SEE DETAIL -03

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

3.00

1.38

1.00

10.88

8.98

.25

.25

M. SHARPE 20170306

1/1

NOTES:

1. INTERPRET DRAWING IAW ASME Y14.100 AND ASME Y14.5-2018.

2. REMOVE ALL BURRS AND SHARP EDGES .06 MAX

3. WORKMANSHIP:

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES, PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES, NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT, CHIPS, GREASE, OIL, FLUX

CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER.

4. CLEAN PART(S) USING CLEANING METHOD AND AGENTS, WHICH SHALL NOT BE INJURIOUS TO THE PART(S) OR THE ENVIRONMENT NOR SHALL ANY PART BE CONTAMINATED BY THE CLEANING AGENT. PRETREAT WITH CHEMICAL

CONVERSION COATING IAW SAE-AMS-2473.

5. WELD IAW ANSI/AWS D1.1/D1.1M-2020.

6. EQUIVALENT, INTERCHANGEABLE COMMERCIAL HARDWARE ACCEPTABLE.

7 MAY BE PURCHASED FROM McMASTER-CARR SUPPLY, CAGE CODE 0KVE6, PO BOX 740100, ATLANTA GA, 30374-0100.

8 PASSIVATE IAW SAE AMS-QQ-P-35, TYPE II OR VII.

20173105 971068

SEE DETAIL -01

N. P. WIGGINS 20170518

B. CHAMBLISS 20170711

B. CHAMBLISS 20170711

C. VON BIEBERSTEIN 20170711

REVISIONS

LTR DESCRIPTION DATE APPROVED

-10 NOMENCLATURE CAGE IDENTIFYING NO MATERIAL / SPECIFICATION ZONE FN

1 WASHER 0KVE6 98370A046 18-8 CRES STEEL, 1.50 OD, .281 ID, .25 THK 1C2 3

1 HANDLE -03 17-4 CRES STEEL ROD, .25 DIA 1C1 2

1 SHAFT -01 17-4 CRES STEEL ROD, .25 DIA 1D4 1

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

EGLIN A.F.B. FL-

18894

D

C

B

A

D

C

B

A

1345678 2

U.S. AIR FORCE

APPLICATION

PARTS LIST

SHEETSCALE:

SIZE

TITLE

THIRD ANGLE PROJECTION

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

.03

.010 .5°

D

X20173106-10

MATERIAL:

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 06 MARCH 2017. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

OR RECONSTRUCTION OF THE DOCUMENT.

APPV

AF FORM 2602 IN MMHE, EGLIN AFB

SIGNATURES ARE ON FILE ON

QUANTITY REQUIRED PER DASH NO.

UNLESS OTHERWISE SPECIFIED

REV

FILENAME:GENERATED USING SOLIDWORKS

EGLIN A.F.B. FL-

18894

D

C

B

A

D

C

B

A

1345678 2

U.S. AIR FORCE

APPLICATION

PARTS LIST

SHEETSCALE:

SIZE

TITLE

THIRD ANGLE PROJECTION

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

FRACTIONS ANGLESDECIMALS

.XX±

.XXX±

DR

CHK

ENG

AIR FORCE AUTHENTICATION AIR FORCE CODE IDENT NO. DRAWING NO.

CURRENT

CODE IDENT NO.

AF FORM

FEB 74 1655

NEXT ASSEMBLY USED ON

ENGINEERING DRAWING LAYOUT D

AIR FORCE RELEASE

.03

.010 .5°

D

X20173106-10

MATERIAL:

X20173106

ALTERNATE F15, PYLON

RACK PIN WELDMENT

X2

X20173106

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEETSCALE:

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X20173106-10

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEET

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEETSCALE:

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X20173106-10

REV

FILENAME:GENERATED USING SOLIDWORKS

18894

D

C

B

D

C

B

A

1345678 2

SHEET

SIZE AIR FORCE CODE IDENT NO. DRAWING NO.

AF FORM

FEB 74 1655 ENGINEERING DRAWING LAYOUT D

D

X2

OR RECONSTRUCTION OF THE DOCUMENT.

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S.

GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON:

ADMINISTRATIVE OR OPERATIONAL USE. DATE: 06 MARCH 2017. OTHER

REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL

POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT

IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC.

2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE

SUBJECT TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS,

DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS

1/1

REVISIONS

LTR DESCRIPTION DATE APPROVED

DETAIL -03

SCALE 4:1

1C1

DETAIL -01

SCALE 4:1

1D4

.38

.094

10.63

.06 X 45°

.125 2X .06 X 45°

3.00

.38

.25 (STK)

.25 (STK)

DO NOT QUOTE HOLES/CHAMFERS