Exhibit A - FINAL CDs - APPROVED-ALTC-2025-02674.pdf

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\CS00 VRR COVER.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

GENERAL NOTES DRAWING INDEX ABBREVIATIONS

KEY PLAN

SYMBOLS AND LEGENDS

ADA ACCESSIBLE ROUTES VICINITY MAP

PROJECT SCOPE

QC BLOCK

MEP ENGINEER:

BOWMAN ENGINEERING

13461 SUNRISE VALLEY. STE 500

HERNDON, VA 20171

FAIRFAX COUNTY

FINAL SUBMITTAL

PROJECT #2305-01

VIENNA RESTROOM RENOVATION

127 CENTER STREET SOUTH,

VIENNA, VIRGINIA 22180

ARCHITECT:

PECK, PECK AND ASSOCS.

12506 LAKE RIDGE DRIVE SUITE C

WOODBRIDGE, VA 22192

1. THE CONTRACTOR IS RESPONSIBLE FOR BEING FAMILIAR WITH ALL DRAWINGS AND SPECIFICATIONS.

2. PRIOR TO BEGINNING OF WORK, THE CONTRACTOR SHALL VISIT THE SITE AND FULLY ACQUAINT HIMSELF WITH

CONDITIONS RELATING TO CONSTRUCTION, TO INCLUDE DIFFICULTIES AND RESTRICTIONS RELATED TO EXECUTION OF

THE WORK, AND EXISTING CONDITIONS.

3. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR SECURING ALL TRADE PERMITS AS REQUIRED FOR WORK HE IS TO PERFORM AND WILL OBTAIN AND PAY FOR ALL REQUIRED INSPECTIONS DURING THE DURATION OF THE WORK.

4. CONTRACTOR SHALL VERIFY ALL DIMENSIONS AND CONDITIONS IN THE FIELD AND SHALL NOTIFY THE COUNTY PROJECT MANAGER OF ANY DISCREPANCIES, OMISSIONS AND / OR ANY OTHER CONFLICTS OR IRREGULARITIES PRIOR TO THE

COMMENCEMENT OF ANY WORK.

5. DO NOT SCALE DRAWINGS. WRITTEN DIMENSIONS GOVERN.

6. ALL DIMENSIONS SHOWN ARE TO THE FINISHED SIDE OF WORK.

7. CONTRACTOR SHALL NOT SUBSTITUTE MATERIALS AND/OR CONSTRUCTION ITEMS SPECIFIED UNLESS APPROVED BY THE

OWNER / CITY PROJECT MANAGER.

8. CONTRACTOR SHALL BE RESPONSIBLE FOR REMOVAL AND DISPOSAL OF ALL CONSTRUCTION DEBRIS AND REFUSE

OFF-SITE IN A LEGAL MANNER.

9. PRIOR TO OCCUPANCY, CONTRACTOR SHALL BE RESPONSIBLE FOR: CLEANING ALL INTERIOR SURFACES, INCLUDING

GLASS SURFACES AND FLOOR SURFACES; REMOVAL OF ALL TRASH, CONST. DEBRIS AND TOOLS, ETC.

10. WORK NOT IN COMPLIANCE WITH THESE CONSTRUCTION DOCUMENTS SHALL BE CORRECTED AT THE CONTRACTOR'S

EXPENSE.

11. THE CONTRACTOR SHALL PROVIDE AND MAINTAIN SAFE WORKING CONDITIONS AT ALL TIMES, INCLUDING BUT NOT

LIMITED TO APPROPRIATE TOOLS, EQUIPMENT, SCAFFOLDING, SHORING, ETC.

12. THE CONTRACTOR SHALL CLEAN UP DAILY TO KEEP THE PROJECT SITE CLEAN AND FREE FROM HAZARDS AT ALL TIMES.

UPON COMPLETION OF THE PROJECT THE CONTRACTOR SHALL REMOVE ALL TRASH AND DEBRIS, BROOM CLEAN THE

ENTIRE PROJECT AREA, AND LEAVE THE SITE IN A CLEAN CONDITION.

13. THE CONTRACTOR SHALL FIELD COORDINATE WITH THE MECHANICAL AND ELECTRICAL DRAWINGS FOR ALL RELATED

WORK REQUIRED BY THOSE TRADES.

14. THE WORDS "PROVIDE" AND "APPLY" INDICATE NEW WORK THAT WILL BE PROVIDED AND INSTALLED BY THE

CONTRACTOR.

15. ALL INSTALLATIONS SHALL BE PERFORMED WITHIN STRICT ACCORDANCE WITH THE MATERIAL, EQUIPMENT, AND/OR

APPLIANCE MANUFACTURER'S SPECIFICATIONS.

16. ALL DAMAGE TO EXISTING CONSTRUCTION AND PROPERTY RESULTING FROM DEMOLITION WORK, NEW WORK, OR OTHER ACTIONS OF THE CONTRACTOR SHALL BE PATCHED, PAINTED, AND REPAIRED WITH NEW MATERIALS TO MATCH

EXISTING ADJACENT CONSTRUCTION.

17. ALL CUTTING AND PATCHING SHALL BE PERFORMED IN A NEAT AND PROFESSIONAL MANNER. ANY EXISTING FINISHES DISTURBED OR DAMAGED BY THE CONTRACTOR DURING THE COURSE OF THE WORK SHALL BE PREPARED TO MATCH

EXISTING IN KIND AND FINISH.

18. NORMAL FUNCTIONS OF THE ADJACENT OCCUPIED AREAS MUST CONTINUE DURING THE CONSTRUCTION PHASES, EVERY EFFORT SHALL BE MADE TO ENSURE SUCH FUNCTIONS ARE NOT DISTURBED. SCHEDULE ANY WORK WHICH MAY BE REQUIRED IN OCCUPIED AREAS DURING UNOCCUPIED HOURS, AND OBTAIN PRIOR APPROVAL FROM THE OWNER.

19. NOISE PRODUCING WORK TO BE SCHEDULED WITH MANAGEMENT BEFORE 8 AM OR AFTER 6PM. PAINT, CARPET GLUE

AND OTHER ODOR PRODUCING WORK MUST BE SCHEDULED WITH MANAGEMENT FOR AFTER HOURS.

20. GC TO NOTIFY OWNER OF ANY EXISTING CONDITIONS THAT MAY CAUSE ISSUES WITH THE EXECUTION OF NEW WORK.

OBSERVE CONDITIONS OF ALL SUBSTRATES FOR CONDITION AND SUITABILITY TO ACCEPT NEW MATERIALS.

DEMOLITION NOTE

A1 A1

NUMBER INDICATES DETAIL

DETAIL

SHEET NUMBER WHERE DRAWN

SHEET NUMBER WHERE INDICATED

NUMBER INDICATES ELEVATION

INTERIOR ELEVATION

SHEET NUMBER WHERE DRAWN

SHEET NUMBER WHERE INDICATED

NUMBER INDICATES SECTION

SHEET NUMBER WHERE DRAWN

SHEET NUMBER WHERE INDICATED

A1 A1

A1 A1

DETAIL SECTION

PARTITION TYPE

NEW WORK NOTE#

WHEN MULTIPLE NEW WORK

NOTES ARE GROUPED, ALL

NOTES APPLY TO

ITEM/AREA INDICATED

ADA

ADJ.

AFF.

ANSI

AWG

AV

BLDG.

B.O.C.A.

CLG.

CLR.

COLR.

CONC.

CONST.

DEMO.

DBL.

EA.

EB.

EXIST.

EXT.

FOW

FRT

FSD

G.F.I.

GYP. BD.

HDWR.

HT.

H.M.

IBC

INFO.

INSUL.

ICC

LB

MAX.

MEP

MTL.

MIN.

MON.

N.

N.F.P.A.

NIC

N.T.S.

NO.

OCC.

O.C.

OFF

PTD.

PLAM.

P.

PR.

RCPT.

RENO.

REQ'D

R.C.P.

RCP

AMERICANS WITH DISABILITIES ACT

ADJUSTABLE

ABOVE FINISH FLOOR

AMERICAN NATIONAL STANDARDS INSTITUTE

AMERICAN WIRE GAUGE

AUDIO VISIUAL

BUILDING

BUILDING OFFICIALS AND CODE

CEILING

CLEAR

COLOR

CONCRETE

CONSTRUCTION

DEMOLITION

DOUBLE

EACH

EXISTING

EXTENSION

FACE OF WALL

FIRE RETARDANT TREATED

FIRE SEPARATION DISTANCE

GROUND FAULT INTERRUPTER

GYPSUM BOARD

HARDWARE

HEIGHT

HOLLOW METAL

INTERNATIONAL BUILDING CODE

INFORMATION

INSULATION

INTERNATIONAL CODE COUNCIL

MAXIMUM

MECHANICAL ELECTRICAL PLUMBING

METAL

MINIMUM

MONITORED

NORTH

NATIONAL FIRE PROTECTION ASSOCIATION

NOT IN CONTRACT

NOT TO SCALE

NUMBER

OCCUPANTS

ON CENTER

OFFICE

PAINTED

PLASTIC LAMINATE

PHASE

PAIR

RECEPTION

RENOVATION

REQUIRED

REFLECTED CEILING PLAN

REFLECTED CEILING PLAN

RM

RR

STO.

S.A.T

SF

SIM.

STRUCT.

THK

THRS.

T.B.D.

T.O.

TYP.

UL

U.N.O.

VDC

V.I.F.

VUSBC

W.

W/

ROOM

RESTROOM

STOREROOM

SUSPENDED ACOUSTIC TILE

SQUARE FEET

SIMILAR

STRUCTURE

THICK

THRESHOLD

TO BE DETERMINE

TOP OF

TYPICAL

UNDERLAYMENT

UNLESS NOTED OTHERWISE

VIRTUAL DESIGN & CONSTRUCTION

VERIFY IN FIELD

VIRGINIA UNIFORM

STATEWIDE BUILDING CODE

WIDTH

WITH

AGENCIES REFERENCED

UL UNDERWRITERS LABORATORIES INC

RAL RIVERBANK ACOUSTICAL LABORATORIES

CK CEDAR KNOLLS ACOUSTICAL LABORATORIES

USG UNITED STATES GYPSUM COMPANY

SA SHINER & ASSOCIATES

C00

GT VD

CO

VE

R

SH

EE

T

NTS

NEW PLUMBING FIXTURE AND

ACCESSORY

LEVEL 2 ALTERATION TO IMPROVE THE SANITARY AND SAFETY CONDITIONS OF THE 1ST

AND 2ND FLOOR RESTROOMS WITH THE ADDITION OF FLOOR DRAINS.

RESTROOMS IN THE BASEMENT (290.57 SF), 1ST (194.67 SF) AND 2ND FLOOR (196.67 SF)

SHALL RECEIVE NEW FINISHES, PLUMBING AND LIGHTING FIXTURES. ALL FIXTURES AND

FINISHES WILL BE REPLACED IN-KIND.

IT IS TECHNICALLY INFEASIBLE TO MODIFY THE MEN'S RESTROOM ON THE 2ND FLOOR TO

PROVIDE AN ACCESSIBLE WATER CLOSET. THEREFORE TO PROVIDE AN ACCESSIBLE

TOILET TO ALL SEXES ON THIS LEVEL, THE EXISTING 2ND FLOOR WOMEN'S RESTROOM

SHALL BE RE-DESIGNATED AS A FAMILY RESTROOM WITH THE ADDITION OF A BABY

CHANGING STATION.

EXISTING BUILDING USE, OCCUPANT LOAD, AND EGRESS PATHS SHALL REMAIN THE SAME.

z 5/13/2026

ALTC-2025-02674

C O

D E

D A

TA

GT VD

G00

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

2026 02 17

1ST FLOOR PLAN

1/8" = 1'-0" G00G00

BASEMENT FLOOR PLAN

1/8" = 1'-0" G00G00

2ND FLOOR PLAN

1/8" = 1'-0" G00G00

PROJECT AREA

PROJECT

AREA

PROJECT AREA

BUILDING DATA / CODE DATA DESIGN NARRATIVE

LEVEL 2 ALTERATION TO IMPROVE THE SANITARY AND SAFETY CONDITIONS OF

THE 1ST AND 2ND FLOOR RESTROOMS WITH THE ADDITION OF FLOOR DRAINS.

RESTROOMS IN THE BASEMENT (290.57 SF), 1ST (194.67 SF) AND 2ND FLOOR

(196.67 SF) SHALL RECEIVE NEW FINISHES, PLUMBING AND LIGHTING FIXTURES.

ALL FIXTURES AND FINISHES WILL BE REPLACED IN-KIND.

IT IS TECHNICALLY INFEASIBLE TO MODIFY THE MEN'S RESTROOM ON THE 2ND

FLOOR TO PROVIDE AN ACCESSIBLE WATER CLOSET. THEREFORE TO PROVIDE AN

ACCESSIBLE TOILET TO ALL SEXES ON THIS LEVEL, THE EXISTING 2ND FLOOR

WOMEN'S RESTROOM SHALL BE RE-DESIGNATED AS A FAMILY RESTROOM WITH

THE ADDITION OF A BABY CHANGING STATION.

EXISTING BUILDING USE, OCCUPANT LOAD, AND EGRESS PATHS SHALL REMAIN THE

SAME.

BW

WOMEN'S RESTROOMBM

MEN'S RESTROOM

1GN

TOILET ROOM

1W

WOMEN'S RESTROOM

2F

TOILET ROOM

2M

MEN'S RESTROOM

DOOR HARDWARE NOTES

1. ALL DOOR HARDWARE EXISTING TO REMAIN.

2. ALL DOORS TO HAVE FREE EGRESS AT ALL TIMES.

3. ROOMS BM, BW, 1GN, 1W, 2M: ADA ACCESSIBLE LEVER WITH THUMBTURN ON

INTERIOR AND KEYED LOCK ON EXTERIOR. FREE EGRESS AT ALL TIMES. 3 PR

HINGES, KICKPLATE ON EXTERIOR.

4. ROOM 2F: ADA ACCESSIBLE LEVER WITH PUSH BUTTON ON INTERIOR AND KEYED

LOCK ON EXTERIOR. FREE EGRESS AT ALL TIMES. 3 PR HINGES, KICKPLATE ON

EXTERIOR.

INTERIOR FINISHES

BUSINESS

EXIT ENCLOSURES &

PASSAGEWAYS

CORRIDORS

ROOMS & ENCLOSED SPACES

CLASS A

CLASS B

CLASS C

2 2 z 5/13/2026

ALTC-2025-02674

AutoCAD SHX Text

SHEET

AutoCAD SHX Text FILE No.

AutoCAD SHX Text

OF

AutoCAD SHX Text

DRAWN

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE :

AutoCAD SHX Text JOB No.

AutoCAD SHX Text

SCALE

AutoCAD SHX Text

DESIGN

AutoCAD SHX Text

DATE

AutoCAD SHX Text

CHKD

AutoCAD SHX Text

PLAN STATUS

AutoCAD SHX Text

COUNTY PROJECT NUMBER

AutoCAD SHX Text Cad file name :

AutoCAD SHX Text

7'-21 2"

7'-71 2"

6'-11"

7'-1"

7'-41 2"

6'-10"

BASEMENT

MEN & WOMEN DEMOLITION PLAN

1/4=1'-0" A01A01

A01

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A01 BASEMENT DEMO PLN & RCP.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

BASEMENT

MEN & WOMEN DEMOLITION REFLECTED CEILING PLAN

1/4=1'-0" A01A01

GRAPHIC SCALE

2 0 2' 4' 8

1/4" = 1'-0"

KEY PLAN

GENERAL NOTES

1. DEDUCT 1: DEDUCT ALL DEMOLITION WORK FROM BASE BID FOR WOMEN &

MEN'S BASEMENT LEVEL RESTROOMS.

2. COORDINATE WITH MEP DRAWINGS FOR FULL EXTENT OF NEW WORK.

3. PROTECT EDGES OF EXISTING FLOOR FINISHES FROM DAMAGE UNTIL NEW

FLOORING AND TRANSITION STRIPS ARE INSTALLED.

4. EXISTING GRAB BARS IN ACCESSIBLE STALLS SHALL BE REMOVED AND

STORED FOR REINSTALLATION.

5. EXISTING SAT GRID SHALL REMAIN.

6. EXISTING SPRINKLER HEADS ARE EXISTING TO REMAIN AND SHALL BE

PROTECTED DURING ALL PHASES OF CONSTRUCTION. COORDINATE WITH

OWNER REGARDING FIRE WATCH REQUIREMENTS.

7. ALL DIMENSIONS SHALL BE FIELD VERIFIED.

9. NOT ALL KEYNOTES APPLY TO EVERY SHEET.

10. REMOVE AREA OF CEILING AS REQUIRED TO INSTALL NEW PIPING FOR

FLOOR DRAINS OF THE SUBSEQUENT FLOOR LEVEL.

LEGEND

PARTITION

DEMOLITION KEY NOTE#

2 X 2 SAT GRID

2 X 4 LIGHT FIXTURE

2 X 2 CEILING DIFFUSER

1 X 4 LIGHT FIXTURE & EGG CRATE

LIGHT DIFFUSER

12 X 6 EXHAUST GRILLE

THERMO DETECTOR

EXISTING

TO REMAINDEMO

TOILET PARTITION

DEMOLITION KEY NOTES

PROJECT

AREA

REMOVE MIRROR, LAMINATE COUNTERS, (2) SURFACE MOUNTED SOAP

DISPENSERS FROM THE MEN'S ROOM ,AND (2) SURFACE MOUNTED SOAP

DISPENSERS FROM THE WOMEN'S ROOM.

REMOVE TOILET SEAT COVER DISPENSER, STORE FOR

REINSTALLATION.3

REMOVE TOILET PAPER DISPENSER AND SANITARY

WASTE RECEPTACLE.4

REMOVE RECESSED PAPER TOWEL DISPENSER / TRASH

RECEPTACLE.5

REMOVE PAPER TOWEL DISPENSER, STORE FOR

REINSTALLATION.6

REMOVE TOILETS, URINALS AND ALL ASSOCIATED

PARTS. CAP ALL PIPING.

7 7

WOMEN'S RESTROOM

BW

WOMEN'S RESTROOM

BM

MEN'S RESTROOM

BM

MEN'S RESTROOM

REMOVE EGG CRATE LOUVER AND FLUORESCENT LUMINARIES IN LIGHT

COVE. EXISTING GYP. BD. BULKHEAD SHALL REMAIN.

BW

GT VD

BS

M

T D

EM

O P

LA

N

RC

P

ROOM NAME AND NUMBERXXX

XXX

RETAIN THERMO DETECTOR, STORE FOR

REINSTALLATION.

FILLING STATION / DRINKING FOUNTAIN

REMOVE SAT CEILING TILES AS INDICATED BY:

CEILING GRID SHALL REMAIN.

REMOVE ALL VERTICAL AREAS OF SAT CEILING IN LOCATIONS

WHERE THERE IS A CEILING HEIGHT CHANGE.

REMOVE TILE FLOOR AND ENTRY THRESHOLDS AS DESIGNATED BY:

INCLUDING AREAS UNDER ALL FIXTURES AND ACCESSORIES. REMOVE WALL

TILE +/- 4'-6" AFF ALONG ENTIRE PERIMETER OF RESTROOM.

REMOVE LIGHT FIXTURES AS DESIGNATED BY THE LEGEND. REFER TO

MEP DRAWINGS FOR MORE INFORMATION.

REMOVE TOILET PARTITIONS AND ALL ASSOCIATED

HARDWARE.

12 12

2 X 2 SAT CEILING TILE

'-8

"-V .I.F

16'-3 1/2"-V.I.F.

'-8

"-V .I.F

16'-3 1/2"-V.I.F.

z

T

7'-11" 7'-9"

1ST FLOOR

WOMEN'S DEMOLITION PLAN

1/4=1'-0" A02A02

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A02 1ST FLOOR DEMO PLN & RCP.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

GRAPHIC SCALE

2 0 2' 4' 8

1/4" = 1'-0"

KEY PLAN

GENERAL NOTES

LEGEND

PARTITION

DEMOLITION KEY NOTE#

1 X 4 SURFACE MOUNTED LIGHT FIXTURE

2 X 2 CEILING DIFFUSER

1 X 4 WALL MOUNTED LIGHT FIXTURE

12 X 6 EXHAUST GRILLE

EXISTING TO REMAINDEMO

TOILET PARTITION

DEMOLITION KEY NOTES

NTS

PROJECT

AREA

1ST FLOOR

WOMEN'S DEMOLITION RCP

1/4=1'-0" A02A02

1ST FLOOR

TOILET ROOM DEMO PLAN

1/4=1'-0" A02A02

1ST FLOOR

TOILET ROOM DEMO RCP

1/4=1'-0" A02A02

REMOVE TILE FLOOR AND ENTRY THRESHOLDS AS INDICATED BY:

INCLUDING AREAS UNDER FIXTURES AND ACCESSORIES. REMOVE

WALL TILE +/- 4'-6" AFF ALONG ENTIRE PERIMETER OF RESTROOM.

REMOVE MIRROR, LAMINATE COUNTERS, AND

LAVATORIES.

REMOVE TOILET PAPER DISPENSER AND SANITARY

WASTE RECEPTACLE, STORE FOR REINSTALLATION.4

REMOVE RECESSED PAPER TOWEL DISPENSER / TRASH

RECEPTACLE.5

REMOVE PAPER TOWEL DISPENSER, STORE FOR

REINSTALLATION.6

REMOVE TOILET SEAT COVER DISPENSER.

A02

GT VD

1S T F

L D

EM

O P

LA

N

RC

P

1. COORDINATE WITH MEP DRAWINGS FOR FULL EXTENT OF NEW WORK.

2. PROTECT EDGES OF EXISTING FLOOR FINISHES FROM DAMAGE UNTIL NEW

FLOORING AND TRANSITION STRIPS ARE INSTALLED.

4. EXISTING GRAB BARS IN ACCESSIBLE TOILETS SHALL BE REMOVED AND

STORED FOR REINSTALLATION.

5. EXISTING GYPSUM BOARD CEILING REMAIN.

6. EXISTING SPRINKLER HEADS ARE EXISTING TO REMAIN AND SHALL BE

PROTECTED DURING ALL PHASES OF CONSTRUCTION. COORDINATE WITH

OWNER REGARDING FIRE WATCH REQUIREMENTS.

7. ALL DIMENSIONS SHALL BE FIELD VERIFIED.

8. EXISTING THERMOSTAT AND WIRE MOLD SHALL BE REMOVED AND STORED

FOR REINSTALLATION.

9. NOT ALL KEYNOTES APPLY TO EVERY SHEET.

T

MECHANICAL UNIT

THERMOSTAT @ 5' AFF

1GN

TOILET ROOM1W

WOMEN'S RESTROOM

1GN

TOILET ROOM

1W

WOMEN'S RESTROOM

GYPSUM BOARD CEILING

REMOVE WALL HUNG LAVATORY, FAUCET, MIRROR

AND ALL ASSOCIATED PARTS.7

2 X 2 CEILING RETURN

ROOM NAME AND NUMBERXXX

XXX

HIGH / LOW DRINKING FOUNTAIN

REMOVE AND STORE (2) SURFACE MOUNTED SOAP DISPENSERS FROM

WOMEN'S ROOM, (1) FROM TOILET ROOM, AND FAUCETS FOR

REINSTALLATION.

8 9

REMOVE TOILETS AND URINALS. REMOVE AND STORE

TOILET AND URINAL FLUSH VALVES FOR

REINSTALLATION.

5'-9"

1'- 6"

REMOVE PORTION OF EXISTING CONCRETE SLAB AS INDICATED

BY: FOR INSTALLATION OF NEW PLUMBING

DRAINS. AREAS OF REMOVAL ARE APPROXIMATE. EXISTING

CONSTRUCTION ASSUMED TO BE 2 12"CONCRETE SLAB ON

CORRUGATE METAL SHEET PER EXISTING DRAWINGS. REFER TO

MEP DRAWINGS FOR MORE INFORMATION.

2'-11"

1'- 6"

REMOVE LIGHT FIXTURES AS DESIGNATED BY THE

LEGEND. REFER TO MEP DRAWINGS FOR MORE

INFORMATION.

2 X 4 SURFACE MOUNTED LIGHT FIXTURE

REMOVE TOILET PARTITION AND ALL ASSOCIATED

HARDWARE.

12'-6 1/2"-V.I.F.

9'- 9 1

/2 "-V

.I.F

6'-7"-V.I.F.

9'- 9"

-V .I.F

12'-6 1/2"-V.I.F.

9'- 9 1

/2 "-V

.I.F

6'-7"-V.I.F.

9'- 9"

-V .I.F z

7'-91

7'-111 2"

T

2ND FLOOR

WOMEN'S DEMOLITION PLAN

1/4=1'-0" A03A03

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A03 2ND FLOOR DEMO PLN & RCP.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

GRAPHIC SCALE

2 0 2' 4' 8

1/4" = 1'-0"

KEY PLAN

GENERAL NOTES

LEGEND

PARTITION

DEMOLITION KEY NOTE#

GYPSUM BOARD CEILING

1 X 4 SURFACE MOUNTED LIGHT FIXTURE

2 X 2 CEILING DIFFUSER

12 X 6 EXHAUST GRILLE

EXISTING TO REMAINDEMO

TOILET PARTITION

DEMOLITION KEY NOTES

NTS

PROJECT

AREA

2ND FLOOR

WOMEN'S DEMO RCP

1/4=1'-0" A03A03

2ND FLOOR

MEN'S DEMOLITION PLAN

1/4=1'-0" A03A03

2ND FLOOR

MEN'S DEMO RCP

1/4=1'-0" A03A03

A03

GT VD

2N D

FL

D

EM

O

P

LA

N

RC

P

1. DEDUCT 2: DEDUCT ALL DEMOLITION WORK FROM BASE BID FOR WOMEN

& MEN'S 2ND FLOOR RESTROOMS.

2. COORDINATE WITH MEP DRAWINGS FOR FULL EXTENT OF NEW WORK.

3. PROTECT EDGES OF EXISTING FLOOR FINISHES FROM DAMAGE UNTIL NEW

FLOORING AND TRANSITION STRIPS ARE INSTALLED.

4. EXISTING GRAB BARS IN ACCESSIBLE STALLS SHALL BE REMOVED AND

STORED FOR REINSTALLATION.

5. EXISTING GYPSUM BOARD CEILING REMAIN.

6. EXISTING SPRINKLER HEADS ARE EXISTING TO REMAIN AND SHALL BE

PROTECTED DURING ALL PHASES OF CONSTRUCTION. COORDINATE WITH

OWNER REGARDING FIRE WATCH REQUIREMENTS.

7. ALL DIMENSIONS SHALL BE FIELD VERIFIED.

8. PROVIDE SCHLUTER S1 ON ALL EXPOSED EDGES OF TILE.

9. EXISTING THERMOSTAT AND WIRE MOLD SHALL BE REMOVED AND STORED

FOR REINSTALLATION.

9. NOT ALL KEYNOTES APPLY TO EVERY SHEET.

10. REMOVE AREA OF CEILING AS REQUIRED TO INSTALL NEW PIPING FOR

FLOOR DRAINS OF THE SUBSEQUENT FLOOR LEVEL.

REMOVE TILE FLOOR AND ENTRY THRESHOLDS AS DESIGNATED BY:

INCLUDING AREAS UNDER FIXTURES AND ACCESSORIES. REMOVE

WALL TILE +/- 4'-6" AFF ALONG ENTIRE PERIMETER OF RESTROOM.

6 5

T

MECHANICAL UNIT

THERMOSTAT @ 5' AFF

2M

WOMEN'S RESTROOM 2M

MEN'S RESTROOM

XXX

XXX

2M

WOMEN'S RESTROOM

2M

MEN'S RESTROOM

ROOM NAME AND NUMBER

ROOF HATCH

REMOVE MIRROR, LAMINATE COUNTERS, AND

LAVATORY SINK.

REMOVE TOILET PAPER DISPENSER AND SANITARY

WASTE RECEPTACLE, STORE FOR REINSTALLATION.4

REMOVE RECESSED PAPER TOWEL DISPENSER / TRASH

RECEPTACLE.5

REMOVE SURFACE MOUNTED PAPER TOWEL

DISPENSER, STORE FOR REINSTALLATION.6

REMOVE TOILET SEAT COVER DISPENSER.

REMOVE PEDESTAL LAVATORY, MIRROR AND ALL

ASSOCIATED PARTS.7

8 REMOVE AND STORE (1) SURFACE MOUNTED SOAP DISPENSERS FROM

MEN'S RR, (1) FROM WOMEN'S RR, AND FAUCETS FOR REINSTALLATION.

REMOVE TOILETS AND URINALS. REMOVE AND STORE

TOILET AND URINAL FLUSH VALVES FOR

REINSTALLATION.

REMOVE TOILET PAPER DISPENSER AND STORE FOR

REINSTALLATION.10

5'-9"9

1'- 6"

2'-11" 1'- 6"

REMOVE AND STORE ROOF HATCH LADDER FOR

REINSTALLATION.

REMOVE LIGHT FIXTURES AS INDICATED, REFER TO

LEGEND FOR MORE INFORMATION.

13 13

REMOVE WOMEN'S RESTROOM SIGN.14

REMOVE TOILET PARTITION AND ALL ASSOCIATED

HARDWARE.

REMOVE PORTION OF EXISTING CONCRETE SLAB AS INDICATED

BY: FOR INSTALLATION OF NEW PLUMBING

DRAINS. AREAS OF REMOVAL ARE APPROXIMATE. EXISTING

CONSTRUCTION ASSUMED TO BE 2 12"CONCRETE SLAB ON

CORRUGATE METAL SHEET PER EXISTING DRAWINGS. REFER TO

MEP DRAWINGS FOR MORE INFORMATION.

6'-4 1/2"-V.I.F.

9'- 8 1

/2 "-V

.I.F

14'-6"-V.I.F.

'-2

1/ 2"

-V .I.F

6'-4 1/2"-V.I.F.

9'- 8 1

/2 "-V

.I.F

14'-6"-V.I.F.

'-2

1/ 2"

-V .I.F z

7'-21

7'-71 2"

6'-11"

7'-1"

7'-41 2"

6'-10"

BASEMENT

MEN & WOMEN RR NEW WORK PLAN

1/4=1'-0" A04A04

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A04 BASEMENT NEW WORK PLN & RCP.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

GRAPHIC SCALE

2 0 2' 4' 8

1/4" = 1'-0"

KEY PLAN

GENERAL NOTES

1. DEDUCT 1: DEDUCT ALL WORK FROM BASE BID FOR WOMEN & MEN'S BASEMENT

LEVEL RESTROOMS.

2. PROVIDE NEW PLUMBING FIXTURES, COORDINATE WITH MEP DRAWINGS FOR FULL

EXTENT OF NEW WORK.

3. PROTECT EDGES OF EXISTING FLOOR FINISHES FROM DAMAGE UNTIL NEW

FLOORING AND TRANSITION STRIPS ARE INSTALLED.

4. REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.

5. PROVIDE NEW TOILET PARTITIONS. REFER TO COLOR SCHEDULE FOR MORE

INFORMATION.

6. PROVIDE TOILET ACCESSORIES, REFER TO FIXTURE SCHEDULE ON A07 FOR MORE

INFORMATION.

7. PAINT DIFFUSER AND RETURN GRILLES WITH P4

8. ALL EXISTING DOORS, HARDWARE AND FRAMES SHALL REMAIN.

9. REFER TO COLOR SCHEDULE AND FINISH SCHEDULE.

10. ALL DIMENSIONS SHALL BE FIELD VERIFIED.

11. PROVIDE SCHLUTER S1 ON ALL EXPOSED OUTSIDE CORNERS OF TILE.

14. REPLACE ALL EXISTING WALL MOUNTED 9"X9"ACCESS PANELS IN-KIND. ALL ACCESS

PANELS SHALL BE WHITE AND LOCKEABLE. FLUSH MOUNT WITH TILE.

15. PATCH AND PREPARE EXISTING WALL TO RECEIVE NEW WALL TILE.

16. PROVIDE TRANSITION, DOUBLE BEVELED, THRESHOLDS AT ALL RESTROOM ENTRIES.

CHANGES IN LEVEL BETWEEN 14" HIGH MINIMUM AND 12" HIGH MAXIMUMS SHALL BE

BEVELED WITH A SLOPE NOT STEEPER THAN 1:2.

LEGEND

PARTITION

NEW WORK KEY NOTE

2X4 LED LIGHT FIXTURE

2 X 2 CEILING DIFFUSER

12 X 6 EXHAUST GRILLE

EXISTING

TO REMAIN

TOILET PARTITION

KEY NOTES

NTS

PROJECT

AREA

BASEMENT

MEN & WOMEN RR NEW REFLECTED CEILING PLAN

1/4=1'-0" A04A04

BASEMENT

MEN'S RR NEW WORK ELEVATIONS

3/8"=1'-0" 3/A041/A04

BASEMENT

WOMEN'S RR NEW WORK ELEVATIONS

3/8"=1'-0" 4/A041/A04

FINISH SCHEDULE

XXX ROOM NAME AND NUMBERXXX

BW

WOMEN'S RESTROOM

B

A

NEW

WORK

2X2 CEILING RETURN

BW

WOMEN'S RESTROOM

BM

MEN'S RESTROOM

BM

MEN'S RESTROOM

1X4 WALL MOUNTED LED LIGHT FIXTURE

B

A

PREP CONCRETE TO RECEIVE NEW FINISHES. INSTALL FLOOR TILE T1.

PROVIDE NEW MIRROR M1, LAVATORY SINKS AND SOLID SURFACE

COUNTERS L1. REINSTALL SURFACE MOUNTED SOAP DISPENSER

TA3, AND FAUCETS. REFER TO INTERIOR ELEVATIONS ON A&B /A04

AND MEP DRAWINGS FOR MORE INFORMATION.

3 INSTALL TOILET SEAT COVER DISPENSER TS1.

REINSTALL SURFACE MOUNTED PAPER TOWEL

DISPENSER TA4.

NOT USED

PROVIDE NEW CEILING TILES C1 AND LED LIGHT

FIXTURES. REFER TO MEP FOR MORE INFORMATION.

1 1

3 3

4 4

5 5

XXX PLUMBING FIXTURE / ACCESSORY

7 PAINT BULKHEAD AND LIGHT COVE WITH P3.

ROOM NAMEROOM #

MEN'S

RESTROOMBM

FLOOR BASE CEILING

TILE

CLNG HEIGHT

T1

BASE

T2

SAT CEILING

TILES

C1/PNT

VARIES

COMMENTS

NORTH WALL SOUTH WALL EAST WALL WEST WALL

TILE/PAINT TILE/PAINT TILE/PAINT TILE/PAINT

ROOM NAMEROOM #

WOMEN'S

RESTROOMBW

FLOOR BASE CEILING

TILE

CLNG HEIGHT

T1

BASE

T2

VARIES

COMMENTS

NORTH WALL SOUTH WALL EAST WALL WEST WALL

TILE/PAINT TILE/PAINT TILE/PAINT TILE/PAINT

SEE ELEVATION T3/ P1

A04

GT VD

BS

M

T N W

W O

RK

P

LN

EL

EV

A

B

A

TA1

B

THERMO DETECTOR

FILLING STATION / DRINKING FOUNTAIN

2' 2'0 4'

3/8" = 1'-0"

REINSTALL SURFACE MOUNTED SANITARY NAPKIN

DISPOSAL TA2.

SAT CEILING TILES

A04 A07

A04 A07

SEE ELEVATION

10 PROVIDE T3 AS FIELD TILE , INSTALLED HORIZONTALLY.

11 PROVIDE ACCENT TILE T6, INSTALLED VERTICALLY,

CENTERED ON FIXTURE.

12 PROVIDE ACCENT TILE T5, INSTALLED VERTICALLY

CENTERED ON FIXTURE.

TYP.

TYP.

TYP.

TYP.

13 PROVIDE SCHLUTER S2 AS COVE TRIM ALONG ENTIRE

PERIMETER.

14 PROVIDE ACCENT TILE T4 ABOVE COUNTER.

TYP.

TYP.

TYP. 10

TYP.

T1 T1 T1U1U1

F1 F2

F3

TS1 TS1

TS1

F1 F2

M1

15 16

15 PROVIDE 3'-10" WIDE X 2'-6" HIGH, CUSTOM SHEET MIRROR M1.

INSTALLED CENTERED OVER COUNTER AT 3'-4" AFF.

16 PROVIDE 5'-0" WIDE X 2'-6" HIGH, CUSTOM SHEET MIRROR M1.

INSTALLED CENTERED OVER COUNTER AT 3'-4" AFF.

M1

TA1 TA1TA2

F3

TA1 L1 L1L1 L1

T3/ P1 T3/ P1

T3/ P1 T3/ P1 T3/ P1

SAT CEILING

TILES

C1/PNT

GYPSUM BOARD CEILING / BULKHEAD

INFILL PARTITION USING METAL STUDS @ 16" O.C. AND GYP. BD. WHERE

RECESSED PAPER TOWEL DISPENSER/ TRASH RECEPTACLE HAS BEEN

REMOVED. ALIGN INFILL WITH OUTER FACE OF EXISTING PARTITION.

TYP.

TYP.

TA1

F1

F2

F1

F2 6'-

8 3 /4

19'-8 3/16"

7'-10 1/2"

6'-

6 3

/4

7'-10 1/2"

6'-

6 3

/4

7'- 1"

19'-8 3/16"

Ø60" TYP.

ADA TURNING RADIUS @ 60"

z

7'-9"7'-9"7'-9"

7'-11"7'-11"7'-11"

TTT

METALBATHROOM SINK FAUCETCORALAISK-15182-4RA

1ST FLOOR

TOILET ROOM NEW WORK PLAN

1/4=1'-0" A05A05

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A05 1ST FLOOR NEW WORK PLN & RCP.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

KEY PLAN

NTS

1ST FLOOR

TOILET ROOM RCP

1/4=1'-0" A05A05

1ST FLOOR

WOMEN'S RR NEW WORK PLAN

1/4=1'-0" A05A05

1ST FLOOR

WOMEN'S RR NEW WORK RCP

1/4=1'-0" A05A05

B

A

1ST FLOOR

TOILET ROOM NEW WORK ELEVATIONS

3/8"=1'-0" 3A051/A05

1ST FLOOR

WOMEN'S RR NEW WORK ELEVATIONS

3/8"1'-0" 4/A052/A05

1GN

TOILET ROOM

1W

WOMEN'S RESTROOM

1GN

TOILET ROOM

C

A

1W

WOMEN'S RESTROOM

GRAPHIC SCALE

2 0 2' 4' 8

1/4" = 1'-0"

KEY PLAN

GENERAL NOTES

1. PROVIDE NEW PLUMBING FIXTURES, COORDINATE WITH MEP DRAWINGS FOR FULL

EXTENT OF NEW WORK.

2. PROTECT EDGES OF EXISTING FLOOR FINISHES FROM DAMAGE UNTIL NEW

FLOORING AND TRANSITION STRIPS ARE INSTALLED.

3. REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.

4. PROVIDE NEW TOILET PARTITIONS. REFER TO COLOR SCHEDULE FOR MORE

INFORMATION.

5. PROVIDE TOILET ACCESSORIES, REFER TO FIXTURE SCHEDULE ON A07 FOR MORE

INFORMATION.

6. PAINT ALL DIFFUSER AND RETURN GRILLES WITH P4.

7. ALL EXISTING DOORS, HARDWARE AND FRAMES SHALL REMAIN.

8. ALL DIMENSIONS SHALL BE FIELD VERIFIED.

9. DOORS AND FRAMES SHALL ONLY RECEIVE PAINT ON THE INTERIOR SIDE OF THE

RESTROOMS.

10. PROVIDE SCHLUTER S1 ON ALL EXPOSED OUTSIDE CORNERS.

13. REFER TO COLOR SCHEDULE AND FINISH SCHEDULE.

14. REINSTALL EXISTING THERMOSTAT AND WIRE MOLD.

14. REPLACE ALL EXISTING WALL MOUNTED 9"X9"ACCESS PANELS IN-KIND. ALL

ACCESS PANELS SHALL BE WHITE AND LOCKABLE. FLUSH MOUNT WITH TILE.

15. PATCH AND PREPARE EXISTING WALL TO RECEIVE NEW WALL TILE.

16. PROVIDE TRANSITION, DOUBLE BEVELED, THRESHOLDS AT ALL RESTROOM ENTRIES.

CHANGES IN LEVEL BETWEEN 14" HIGH MINIMUM AND 12" HIGH MAXIMUMS SHALL BE

BEVELED WITH A SLOPE NOT STEEPER THAN 1:2.

LEGEND

PARTITION

NEW WORK KEY NOTE

2X4 LED LIGHT FIXTURE

2 X 2 CEILING DIFFUSER

12 X 6 EXHAUST GRILLE

EXISTING

TO REMAIN

TOILET PARTITION

KEY NOTES

PROJECT

AREA

FINISH SCHEDULE XXX ROOM NAME AND NUMBERXXX

NEW

WORK

2X2 CEILING RETURN

1X4 WALL MOUNTED LED LIGHT FIXTURE

XXX PLUMBING FIXTURE / ACCESSORY

ROOM NAMEROOM #

GENDER

NEUTRAL RR1GN

FLOOR BASE CEILING

TILE

CLNG HEIGHT

T1

BASE

B1

EXIST. GYP

TO REMAIN

P3 7'-9"

COMMENTS

NORTH WALL SOUTH WALL EAST WALL WEST WALL

TILE TILE TILE TILE

ROOM NAMEROOM #

WOMEN'S

RESTROOM1W

FLOOR BASE CEILING

TILE

CLNG HEIGHT

T1

BASE

B1 7'-11"

COMMENTS

NORTH WALL SOUTH WALL EAST WALL WEST WALL

TILE TILE TILE TILE

T3 T3T3

T3 T3T3

A05

GT VD

1S T F

L N

EW

W O

RK

P

LA

N

EL

EV

A

B

A B 2'

2'

4'

3/8" = 1'-0"

INSTALL TOILET SEAT COVER DISPENSER TS1, REINSTALL

SURFACE MOUNTED SANITARY NAPKIN DISPOSAL TA2,

AND TOILET PAPER DISPENSER TA1.

REINSTALL SURFACE MOUNTED PAPER TOWEL

DISPENSER TA4.

PAINT CEILING WITH P3.

INFILL PARTITION USING METAL STUDS @ 16" O.C. AND GYP. BD. WHERE

RECESSED PAPER TOWEL DISPENSER/ TRASH RECEPTACLE HAS BEEN

REMOVED. ALIGN INFILL WITH OUTER FACE OF EXISTING PARTITION.

13 PROVIDE S2 SCHLUTER COVE TRIM ALONG ENTIRE

PERIMETER.

14 PROVIDE T4 ABOVE COUNTER AS AN ACCENT 1 TILE.

15 PROVIDE 1'-6" WIDE X 2'-6" HIGH, CUSTOM SHEET MIRROR M1.

INSTALL CENTERED OVER LAVATORIES AT 3'-4" AFF.

16 PROVIDE 3'-6" WIDE X 2'-6" HIGH, CUSTOM SHEET MIRROR M1.

INSTALL CENTERED OVER LAVATORY AT 3'-4" AFF.

PREP CONCRETE TO RECEIVE NEW FINISHES. INSTALL FLOOR TILE T1.

PROVIDE NEW MIRROR M1, LAVATORY SINKS AND SOLID SURFACE

COUNTERS L1. REINSTALL SURFACE MOUNTED SOAP DISPENSER

TA3, AND FAUCETS. REFER TO INTERIOR ELEVATIONS ON A&B /A04

AND MEP DRAWINGS FOR MORE INFORMATION.

TYP.

PROVIDE BABY CHANGING STATION CS1.

PROVIDE NEW MIRROR M1, WALL MOUNTED LAVATORY SINK L2.

REINSTALL SURFACE MOUNTED SOAP DISPENSER TA3, AND

FAUCETS. REFER TO INTERIOR ELEVATIONS ON A&B /A05 AND MEP

DRAWINGS FOR MORE INFORMATION.

PAINT MECHANICAL UNIT WITH ELECTROSTATIC PAINT P4.

A05 A07

TYP.

TYP.

T1

F3

C

B

TYP. 10

TYP.

TYP.

TYP.11

TYP.

TYP.14

TS1

F1

F2

TA1 TA2

TA3

TA4

TA3

TA4

L1 T1

SEE ELEVATION

SEE ELEVATION

EXIST. GYP

TO REMAIN

P3

TS1

TA1

A05 A07

GYPSUM BOARD CEILING / BULKHEAD

TYP.

17 PROVIDE P.LAM PL1 REMOVABLE APRON PANEL.

L1

TA3

PROVIDE T3 AS FIELD TILE , INSTALLED HORIZONTALLY.

PROVIDE ACCENT TILE T6, INSTALLED VERTICALLY,

CENTERED ON FIXTURE.

PROVIDE ACCENT TILE T5, INSTALLED VERTICALLY

CENTERED ON FIXTURE.

7'- 9"

9'-9"

7'- 9"

6'-6 15/16"

10'-1 3/4"

7'-

7'-

13'-10 1/2" 6'-2 1/8"

7'-

18 REPAIR EXISTING AREA AT EXISTING SLAB AND CORRUGATED

METAL AS REQUIRED PRIOR TO INSTALLING FLOOR FINISH.

2'-1" 8'- 5"

1X4 LED LIGHT FIXTURE

19 PROVIDE T3 AS FIELD TILE WITHIN ALL SIDES OF THE WINDOW WELL.

USE SCHLUTER S1 ON OUTSIDE CORNER OF PERIMETER OF

WINDOW. PAINT WINDOW MULLION USING P2.

2'-0"

ADA TURNING RADIUS @ 60"

Ø60" TYP.

z

7'-91

7'-111 2"

T

2ND FLOOR

TOILET ROOM NEW WORK PLAN

1/4=1'-0" A06A06

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A06 2ND FLOOR NEW WORK PLN & RCP.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

KEY PLAN

NTS

2ND FLOOR

TOILET ROOM NEW WORK RCP

1/4=1'-0" A06A06

2ND FLOOR

MEN'S RR NEW WORK PLAN

1/4=1'-0" A06A06

2ND FLOOR

MEN'S RR NEW WORK RCP

1/4=1'-0" A06A06

B

A

2ND FLOOR

TOILET ROOM NEW WORK ELEVATIONS

3/8"1'-0" 5/A061/A06

2ND FLOOR

MEN'S NEW WORK ELEVATIONS

3/8"=1'-0" 6/A062/A06

2F

TOILET ROOM

2M

MEN'S RESTROOM

2F

TOILET ROOM 2M

MEN'S RESTROOM

B

A

GRAPHIC SCALE

2 0 2' 4' 8

1/4" = 1'-0"

KEY PLAN

GENERAL NOTES

1. DEDUCT 2: DEDUCT ALL WORK FROM BASE BID FOR WOMEN & MEN'S 2ND FLOOR

RESTROOMS.

2. PROVIDE NEW PLUMBING FIXTURES, COORDINATE WITH MEP DRAWINGS FOR FULL

EXTENT OF NEW WORK.

3. PROTECT EDGES OF EXISTING FLOOR FINISHES FROM DAMAGE UNTIL NEW

FLOORING AND TRANSITION STRIPS ARE INSTALLED.

4. REFER TO INTERIOR ELEVATIONS FOR MORE INFORMATION.

5. PROVIDE NEW TOILET PARTITIONS. REFER TO COLOR SCHEDULE FOR MORE

INFORMATION.

6. PROVIDE TOILET ACCESSORIES, REFER TO FIXTURE SCHEDULE ON A09 FOR MORE

INFORMATION.

7. PREP, PATCH AND REPAIR ALL GYPSUM WALLBOARD SURFACES TO RECEIVE NEW

PAINT.

8. PAINT ALL DIFFUSER AND RETURN GRILLES.

9. DOORS AND FRAMES SHALL ONLY RECEIVE PAINT ON THE INTERIOR SIDE OF THE

RESTROOMS.

10. ALL DIMENSIONS SHALL BE FIELD VERIFIED

11. ALL EXISTING DOORS, HARDWARE AND FRAMES SHALL REMAIN.

12. PROVIDE SCHLUTER S1 ON ALL EXPOSED OUTSIDE CORNERS.

13. REINSTALL EXISTING THERMOSTAT AND WIRE MOLD.

14. REPLACE ALL EXISTING WALL MOUNTED 9"X9"ACCESS PANELS IN-KIND. ALL

ACCESS PANELS SHALL BE WHITE AND LOCKABLE. FLUSH MOUNT WITH TILE.

16. PATCH AND PREPARE EXISTING WALL TO RECEIVE NEW WALL TILE.

16. PROVIDE TRANSITION, DOUBLE BEVELED, THRESHOLDS AT ALL RESTROOM ENTRIES.

CHANGES IN LEVEL BETWEEN 14" HIGH MINIMUM AND 12" HIGH MAXIMUMS SHALL BE

BEVELED WITH A SLOPE NOT STEEPER THAN 1:2.

LEGEND

PARTITION

NEW WORK KEY NOTE

2X4 LED LIGHT FIXTURE

2 X 2 CEILING DIFFUSER

12 X 6 EXHAUST GRILLE

EXISTING

TO REMAIN

TOILET PARTITION

KEY NOTES

PROJECT

AREA

FINISH SCHEDULE XXX ROOM NAME AND NUMBERXXX

NEW

WORK

2X2 CEILING RETURN

1X4 LED LIGHT FIXTURE

XXX PLUMBING FIXTURE / ACCESSORY

ROOM NAMEROOM #

TOILET ROOM2F

FLOOR BASE CEILING

TILE

CLNG HEIGHT

T1

BASE

S1

EXIST.

TO REMAIN

P3 7'-91

2"

COMMENTS

NORTH WALL SOUTH WALL EAST WALL WEST WALL

TILE/PAINT

T2

TILE/PAINT

T2

TILE/PAINT

SEE ELEVATION

TILE/PAINT

T2

ROOM NAMEROOM #

MEN'S

RESTROOM2M

FLOOR BASE CEILING

TILE

CLNG HEIGHT

T1

BASE

S1

EXIST.

TO REMAIN

P3 7'-111

2"

COMMENTS

NORTH WALL SOUTH WALL EAST WALL WEST WALL

TILE/PAINT TILE/PAINT TILE/PAINT TILE/PAINT

ROOF HATCH

T2 T2 SEE ELEVATION SEE ELEVATION

A

B

A

B

A06

GT VD

2N D

FL

N

EW

W

O

RK

EL

EV

INSTALL TOILET SEAT COVER DISPENSER TS1, REINSTALL SURFACE MOUNTED

SANITARY NAPKIN DISPOSAL TA2, AND TOILET PAPER DISPENSER TA1.

REINSTALL SURFACE MOUNTED PAPER TOWEL DISPENSER TA4.

PAINT CEILING WITH P3.

PROVIDE T4 ABOVE COUNTER AS AN ACCENT TILE.

PROVIDE 1'-6" WIDE X 2'-6" HIGH, CUSTOM SHEET MIRROR M1, INSTALLED

3'-4" AFF.

PROVIDE 3'-6" WIDE X 2'-6" HIGH, CUSTOM SHEET MIRROR M1.

INSTALL CENTERED TO THE LAVATORIES AT 3'-4" AFF.

PAINT MECHANICAL UNIT WITH ELECTROSTATIC PAINT P4.

PREP CONCRETE TO RECEIVE NEW FINISHES. INSTALL FLOOR TILE T1.

PROVIDE NEW MIRROR M1, LAVATORY SINKS AND SOLID SURFACE

COUNTERS L1. REINSTALL SURFACE MOUNTED SOAP DISPENSER

TA3, AND FAUCETS. REFER TO INTERIOR ELEVATIONS ON A&B /A06

AND MEP DRAWINGS FOR MORE INFORMATION.

PROVIDE NEW MIRROR M1, WALL MOUNTED LAVATORY SINK L2.

REINSTALL SURFACE MOUNTED SOAP DISPENSER TA3, AND FAUCETS.

REFER TO INTERIOR ELEVATIONS ON A&B /A06 AND MEP DRAWINGS FOR

MORE INFORMATION.

4 6

9 9

REINSTALL EXISTING SURFACE MOUNTED ROOF HATCH ACCESS

LADDER. PAINT LADDER AND INTERIOR SIDE OF ROOF HATCH WITH

P2. PAINT ROOF HATCH SHAFT WITH P3 WITH GLOSS FINISH.

17 INSTALL TOILET SEAT COVER DISPENSER TS1, AND

REINSTALL TOILET PAPER DISPENSER TA1.

TYP.

18 REINSTALL EXISTING THERMOSTAT. REFER TO MEP

DRAWINGS FOR MORE INFORMATION.

TYP.

TYP.

L1T1T1

U1 U1 L2L2

TYP.

TYP.

INFILL PARTITION USING METAL STUDS @ 16" O.C. AND GYP. BD. WHERE

RECESSED PAPER TOWEL DISPENSER/ TRASH RECEPTACLE HAS BEEN

REMOVED. ALIGN INFILL WITH OUTER FACE OF EXISTING PARTITION.

A05 A07

A05 A07

19 PROVIDE NEW SIGNAGE FOR TOILET ROOM. MATCH

BUILDING STANDARD.

PROVIDE SCHLUTER S2 AS COVE TRIM ALONG ENTIRE PERIMETER.

20 PROVIDE P.LAM PL1 REMOVABLE APRON PANEL.

TA4

2' 2'0 4'

3/8" = 1'-0"

PROVIDE T3 AS FIELD TILE , INSTALLED HORIZONTALLY.

PROVIDE ACCENT TILE T6, INSTALLED VERTICALLY, CENTERED ON FIXTURE.

PROVIDE ACCENT TILE T5, INSTALLED VERTICALLY CENTERED ON FIXTURE.

PROVIDE T3 AS FIELD TILE WITHIN ALL SIDES OF THE WINDOW WELL.

USE SCHLUTER S1 ON OUTSIDE CORNER OF PERIMETER OF

WINDOW. PAINT WINDOW MULLION USING P2.

GYPSUM BOARD CEILING / BULKHEAD

7'- 9"

9'-9"

7'- 9"

6'-8"

7'-

14'-6"

10'-1 7/8"

7'-

1/ 2"

2'-0"

ADA TURNING RADIUS @ 60"

Ø60" TY

P.

z

EXISTING TOILET PAPER

DISPENSER

SHEET MIRROR

CUSTOM SIZES

" M

AX

. T

O

RE

FL

EC

TIV

E

SU

RF

AC

E

EXISTING SIDE

WALL GRAB

36"

42"

EXISTING VERTICAL

GRAB BAR

CL

OF

WATER CLOSET

12"12"

FOW @ REAR OF TOILETFOW @ REAR OF TOILET

CL

40"

EXISTING SURFACE

MOUNTED SANITARY

NAPKIN DISPOSAL

TOILET SEAT COVER, METPAR CORP.

TSC-100

FINISH: STAINLESS STEEL

EXISTING SURFACE

MOUNTED SOAP

DISPENSER

EXISTING REAR

WALL GRAB

BABY CHANGING

STATION, KOALA

KARE, KB310-SSWM

FINISH: STAINLESS

STEEL, SURFACE

MOUNTED

3 4"

BO

TTO

M O

F

CL

O

SE

D

BE

D A.

F.F

CLFRONT

OF

W.C.

8"

HOOK, BOBRICK, B-9542,

FINISH: SATIN STAINLESS

STEEL, SURFACE MOUNTED

T.O. CLOTHES

HOOK MOUNT TO

AND CENTERED

HORIZONTALLY AT

ALL RESTROOM

DOORS

L1 L2T1

TA1 TA2

F3F2F1 TS1

TA3

M1

CS1

TA5

24" STANDARD

INSTALLATION

17" MAX ADA

INSTALLATION

U1WATERCLOSET

REFER TO MEP DWGS FOR

SPECIFICATIONS

URINAL

REFER TO MEP DWGS FOR

SPECIFICATIONS

FOW @ REAR OF TOILET

EXISTING SURFACE

MOUNTED PAPER

TOWEL DISPENSER

TA4

FOW

UNDER-MOUNT LAVATORY

REFER TO MEP DWGS FOR

SPECIFICATIONS

WALL MOUNT LAVATORY

REFER TO MEP DWGS FOR

SPECIFICATIONS

MOUNTING HEIGHTS

3/8"=1'-0" A08A08

B ow m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

S:\Projects\Active\Vienna RR\CAD\SHEET SETS\sheets\A07 SCHEDULES.dwg

AS NOTED

2'

GRAPHIC SCALE: 1/4" = 1'-0"

4' 0' 4' 8'

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

GRAPHIC SCALE

GENERAL NOTES

1. COORDINATE WITH MEP DRAWINGS FOR FULL EXTENT OF NEW WORK.

2. PROVIDE BLOCKING AS REQUIRED FOR ALL NEW AND REINSTALLED EXISTING

ACCESSORIES.

LEGEND

NTS

XXX NEW PLUMBING FIXTURE

AND ACCESSORY

KEY PLAN

2'-

REINSTALL EXISTING

FAUCET

SOLID SURFACE SS1 FINISH ON 12" EXT.

GRADE PLYWOOD

ACCENT TILE T4

L1 LAVATORY , REFER TO PLUMBING PLAN

P.LAM PL1 ON 34" TREATED PLYWOOD REMOVABLE APRON

PANEL W/Z-CLIPS MOUNTED TO 3x3 CLEAT EACH END

A07

SC

HE

DU

LE

S & D

ET

AI

LS

SECTION DETAIL

1/2"=1'-0" A07

2' 2'0 4'

3/8" = 1'-0"

4'2'01'

1/2" = 1'-0"

SECTION DETAIL

1/2"=1'-0" A07

2'-0 3/8"

9" CL

R.

MIRROR M1

ADHERED TO TILE

6" 2'-

EXISTING FAUCET

TILE - REFER TO ELEVATIONS FOR TILE

L2 WALL MOUNTED LAVATORY,

REFER TO PLUMBING PLAN

MIRROR M1

ADHERED TO TILE

6"

P-TRAP, REFER TO PLUMBING PLAN

P-TRAP WITH INSULATION, REFER

TO PLUMBING SHEETS

FLOOR TILE T1

CONC.3"X3"X1/4" STL. ANGLE W/ WELDED END PLATES. SECURE

AND PLATE W/ E.B. TO MASONRY PARTITIONS AND W/ LB. TO

MTL. STUD PARTITION

2X4 PRESSURE TREATED WD. 3'-0" O.C., MAX., CENTERED

BETWEEN SINKS & EACH END WALL

COVE TRIM S2

EXISTING PARTITION

NEW 2x PRESSURE TREATED WD, PAINTED P2. BLOCKING BETWEEN

EXISTING METAL STUD

FLOOR TILE T1

COVE TRIM S2

8"

EXISTING PARTITION

SEALANT ALONG ENTIRE

PERIMETER ON BOTH

SIDES OF S2 TRIM

SEALANT ALONG ENTIRE

PERIMETER ON BOTH

SIDES OF S2 TRIM

COMPLY WITH ALL APPLICABLE AWI STANDARDS

z m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

J:\T\140339-01-003 Town Hall Bathroom Reno Vienna\Drawings\CADD\ELEC\E00 COVER SHEET-ELEC.dwg

AS NOTED

C

EN

TE

R

S

TR

EE

T

SO

U

TH

VI

EN

N A, V

IR

G

IN

IA

12/12/2025PERMIT RESUBMITTAL1

DC JM

ELECTRICAL NOTES AND SPECIFICATIONS

DRAWING LIST

1. ALL WORK SHALL BE DONE IN CONFORMANCE WITH ALL LOCAL AND STATE CODES RULES AND REGULATIONS, THE LATEST ADOPTED JURISDICTIONAL CODES, AND OF THE AUTHORITY HAVING JURISDICTION.

2. OBTAIN AND PAY FOR ALL PERMITS, ALL FEES AND ALL TAXES.

3. IT IS THE INTENTION OF THE SPECIFICATIONS AND DRAWINGS TO CALL FOR FINISHED WORK, TESTED AND READY FOR OPERATION. WHENEVER THE WORD "PROVIDE" IS USED, IT SHALL MEAN "FURNISH AND INSTALL

COMPLETE AND READY FOR USE".

4. PROVIDE ALL LABOR, MATERIAL, EQUIPMENT, FIXTURES, SERVICES AND PERFORM ALL OPERATIONS REQUIRED FOR A COMPLETE AND SAFE INSTALLATION OF THE ELECTRICAL SYSTEMS AND RELATED WORK.

ELECTRICAL SYSTEMS AND EQUIPMENT SHALL IN GENERAL INCLUDE THE FOLLOWING:

4.A. GENERAL PROVISIONS FOR ELECTRICAL WORK

4.B. WIRING, DISTRIBUTION EQUIPMENT, RACEWAYS AND DEVICES

4.C. LIGHTING FIXTURES AND LAMPS

4.D. GROUNDING SYSTEM

4.E. TELEPHONE CONDUIT

4.F. MECHANICAL EQUIPMENT, MOTORS AND PLUMBING EQUIPMENT, WIRING AND CONDUIT

4.G. FIRE ALARM SYSTEM

4.H. INSTALLATION AND ALL CONNECTIONS.

5. PROVIDE ALL MATERIAL AND EQUIPMENT NOT INDICATED AS EXISTING IN THE CONTRACT DOCUMENTS. ALL MATERIAL SHALL BE NEW AND THE BEST PRODUCTS OF REPUTABLE MANUFACTURERS AND SHALL BE IN NEW

CONDITION AT ACCEPTANCE OF WORK.

6. PROVIDE A GUARANTEE TO COVER ALL MATERIALS, LABOR AND EQUIPMENT. GUARANTEE SHALL BE FOR A PERIOD OF ONE YEAR FROM THE DATE OF ACCEPTANCE BY THE OWNER. GUARANTEE SHALL COVER PAYMENT FOR ANY REPAIRS OR REPLACEMENTS CAUSED BY DEFECTIVE WORKMANSHIP OR FAULTY

MATERIALS WITHIN THE PERIOD COVERED BY THE GUARANTEE.

7. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH NECA-1 GOOD WORKMANSHIP IN ELECTRICAL

CONSTRUCTION.

8. THE CONTRACTOR SHALL WALK THE WORK SITE PRIOR TO BIDDING AND VERIFY EXISTING CONDITIONS.

DRAWINGS ARE DIAGRAMMATIC AND REPRESENT THE ENGINEERING ASSESSMENT AT THE TIME OF DESIGN.CIRCUITS SHOWN ARE BASED ON RECORD DRAWING AND FIELD CONDITIONS. CONDUIT SHALL NOT BE CONSIDERED AS DIRECT PATH STRAIGHT RUNS. THE CONTRACTOR SHALL EXPECT TO ROUTE CONDUIT AROUND EXISTING STRUCTURAL COMPONENTS AND ALL EQUIPMENT. THE CONTRACTOR SHALL PROVIDE REQUIRED PULL BOXES TO MAINTAIN NO MORE THAN FOUR 90 DEGREE EQUIVALENT BENDS IN EACH CONDUIT

RUN.

9. PROVIDE ALL SCAFFOLDING, RIGGING, HOISTING, AND SERVICES NECESSARY FOR ERECTION AND DELIVERY INTO THE PREMISES OF ANY EQUIPMENT AND APPARATUS, WHETHER FURNISHED BY THIS CONTRACT OR

OWNER, AND REMOVAL OF SAME FROM PREMISES WHEN NO LONGER REQUIRED.

10. INSTALL ALL WORK IN A NEAT AND ORDERLY MANNER, USING ONLY WORKMEN THOROUGHLY QUALIFIED IN

THE TRADE OR DUTIES THEY ARE TO PERFORM. ROUGH WORK WILL BE REJECTED.

11. UNLESS OTHERWISE REQUIRED BY TRADE CUSTOM OR SPECIFIED UNDER ANOTHER SECTION OF THE SPECIFICATIONS, CUTTING AND PATCHING SHALL BE DONE BY THE APPROPRIATE TRADE. PROVIDE SKETCHES

SHOWING THE LOCATIONS AND SIZES OF ALL OPENINGS, CHASES ETC. REQUIRED.

12. DO NOT CUT STRUCTURAL MEMBERS WITHOUT THE APPROVAL OF THE ARCHITECT/ENGINEER, AND ALL SUCH

CUTTING SHALL BE DONE IN MANNER DIRECTED BY HIM.

13. MAINTAIN CLEAN WORK AREA AT ALL TIMES DURING CONSTRUCTION.

14. TEST ALL LIGHTING, POWER, FIRE ALARM AND OTHER SYSTEMS. SYSTEMS SHALL OPERATE SATISFACTORILY

AS DESIGNED AND INTENDED. REPORT ANY DEFICIENCIES TO THE ARCHITECT/ENGINEER.

15. PROVIDE A FIELD-APPLIED WARNING LABEL ON EACH SWITCHBOARD, PANELBOARD, CONTROL PANEL, STARTER, VFD, AND MOTOR CONTROL CENTER TO WARN QUALIFIED PERSONS OF POTENTIAL ELECTRIC ARC

FLASH HAZARD, PER NEC 110.16.

16. GENERAL PROVISION FOR ELECTRICAL WORK:

16.A. DRAWINGS: ELECTRICAL DRAWINGS ARE CONSIDERED DIAGRAMMATIC AND INDICATE GENERAL

ARRANGEMENT OF WORK AND SYSTEMS. REFER TO ARCHITECTURAL DRAWINGS TO VERIFY

LOCATION OF EQUIPMENT, ETC. COORDINATE ROUGH-IN REQUIREMENTS AND INSTALLATION

REQUIREMENTS WITH OTHER TRADES.

16.B. QUALITY OF MATERIALS: NEW, BEST OF THEIR RESPECTIVE KIND, FREE FROM DEFECTS, AND LISTED

BY UNDERWRITERS LABORATORIES, INC. AND BEARING THEIR LABEL.

16.C. VOLTAGE CHARACTERISTICS: 277/480 VOLT AND 120/208 VOLT, 3 PHASE, 4 WIRE, 60 HERTZ WITH

GROUNDED NEUTRAL AS NOTED.

16.D. SHOP DRAWINGS:

16.D.1. SUBMIT ELECTRONIC SHOP DRAWINGS FOR ALL FIXTURES AND DEVICES. OBTAIN

APPROVAL BEFORE EQUIPMENT IS ORDERED, BUILT OR INSTALLED. CATALOGS,

PAMPHLETS, OR OTHER DOCUMENTS SUBMITTED TO DESCRIBE ITEMS FOR WHICH

APPROVAL IS BEING REQUESTED SHALL BE AS SPECIFIED AND IDENTIFICATION CATALOG,

PAMPHLET, ETC., OF ITEM SUBMITTED SHALL BE CLEARLY NAMED IN INK. DATA OF A

GENERAL NATURE AND FAXES WILL NOT BE ACCEPTED. SUBMITTAL SHALL INCLUDE

CONTRACTOR'S NAME AND NAME OF JOB.

16.D.1.a. LIGHTING FIXTURES 16.D.1.b. LIGHTING CONTROLS 16.D.1.c. WIRING DEVICES 16.D.1.d. WIRING DEVICE PLATES 16.D.1.e. BUILDING WIRE 16.D.1.f. DISTRIBUTION EQUIPMENT (PANEL BOARDS, TRANSFORMERS, ETC) 16.D.1.g. SAFETY SWITCHES 16.D.1.h. FIRE ALARM APPLIANCES AND PANELS 16.D.1.i. RGS, IMC, EMT, PVC CONDUIT

16.D.2. PROVIDE LIGHTING CONTROLS SHOP DRAWINGS THAT SHALL INCLUDE, BUT NOT LIMITED

TO, ALL THE FOLLOWING:

16.D.2.a. MANUFACTURER DATA SHEETS ON EACH PRODUCT TO BE USED INCLUDING:

16.D.2.a.a. CATALOG SHEETS AND SPECIFICATIONS.

16.D.2.a.b. RATINGS, CONFIGURATIONS, STANDARD WIRING DIAGRAMS, DIMENSIONS, COLORS, SERVICE CONDITION REQUIREMENTS, AND

INSTALLED FEATURES.

16.D.2.a.c. INSTALLATION INSTRUCTIONS.

16.D.2.a.d. WARRANTY INFORMATION.

16.D.2.b. PROVIDE WIRING DIAGRAMS AND DIMENSIONED FLOOR PLANS THAT

INCLUDE THE VARIOUS COMPONENTS OF THE SYSTEM SPECIFIED

INCLUDING:

16.D.2.b.a. COMPOSITE WIRING AND/OR SCHEMATIC DIAGRAM OF EACH CONTROL

CIRCUIT AS PROPOSED TO BE INSTALLED.

16.D.2.b.b. FLOOR PLANS THAT SHOW LOCATION OF ALL DEVICES, INCLUDING AT

MINIMUM SENSORS, LOAD CONTROLLERS, AND SWITCHES/DIMMERS

FOR EACH AREA ON REFLECTED CEILING PLANS.

16.D.2.b.c. FLOOR PLANS THAT SHOW THE DIFFERENT LIGHTING CONTROL ZONES

PER ROOM OR SPACE AS SHOWN ON THE LIGHTING PLANS, ENLARGED

PLANS, AND SEQUENCE OF OPERATIONS.

16.D.2.b.d. PROVIDE ROOM/SPACE DETAILS INCLUDING PRODUCTS AND SEQUENCE

OF OPERATION FOR EACH ROOM OR SPACE. ILLUSTRATE TYPICAL

ACCEPTABLE ROOM/SPACE CONNECTION TOPOLOGIES.

16.D.2.b.e. NETWORK RISER DIAGRAM INCLUDING FLOOR AND BUILDING LEVEL

DETAILS. INCLUDE NETWORK CABLE SPECIFICATION. ILLUSTRATE

POINTS OF CONNECTION TO INTEGRATED SYSTEMS. COORDINATE

INTEGRATION WITH MECHANICAL AND/OR OTHER TRADES.

16.E. INSTALL ALL NEW WORK WITH MINIMUM INTERFERENCE TO EXISTING FACILITIES.

16.F. VISIT SITE AND INSPECT EXISTING FACILITIES BEFORE BID IN ORDER TO ENSURE PROPER

EVALUATION OF WORKING CONDITIONS AND LOCATION OF EXISTING EQUIPMENT.

17. WIRING, DISTRIBUTION EQUIPMENT AND DEVICES:

17.A. CONDUCTORS: COPPER, IN ACCORDANCE WITH ASTM STANDARDS, SIZE REFERENCES AWG.

CONDUCTORS ARE BASED ON 90°C RATING. NO. 10 AND SMALLER - SOLID, THHN OR THHW 600 VOLT;

NO. 8 AND LARGER - STRANDED THHW OR THHN 600 VOLT. MINIMUM SIZE: NO. 12.

17.A.1. TYPE MC CABLE SHALL BE INTERLOCKED STEEL ARMOR WITH INSULATED GROUNDING

CONDUCTOR FOR BRANCH CIRCUITING AND FEEDERS, UP TO A MAXIMUM OF 20 AMPS PER

CIRCUIT, MAY BE SUBSTITUTED FOR CONDUCTORS IN CONDUIT. SUPPORT CABLE EVERY

6'-0" AND WITHIN 12" OUTLET AND IN ACCORDANCE WITH THE NEC. CABLE MUST BE

SUPPORTED IN A NEAT AND ORDERLY MANNER.

CONTRACTOR SHALL PROVIDE NEUTRAL CONDUCTOR IN SWITCH BOXES COMPLYING WITH NEC

404.2(C).

17.A.1. ALL CONDUCTORS SHALL BE IDENTIFIED BY COLOR AS INDICATED IN THE COLOR CODE

CHART.

COLOR CODE CHART

PHASE A PHASE B PHASE C NEUTRAL GROUND

120/208V BLACK RED BLUE WHITE GREEN

277/480V BROWN ORANGE YELLOW GRAY GREEN

17.B. RACEWAYS: (ROUTE CONCEALED BEHIND OR ABOVE BUILDING FINISHES UON)

17.B.1. ELECTRIC METALLIC TUBING (EMT), THIN WALL PIPE, GALVANIZED, MINIMUM 1/2" EXCEPT

AS NOTED OR REQUIRED FOR WIRING.

17.B.2. ALL FITTINGS AND COUPLINGS SHALL BE STEEL - CAST FITTINGS PROHIBITED.

17.B.3. BELOW GRADE: MINIMUM 1" SCHEDULE 40 PVC, RIGID GALVANIZED STEEL CONDUIT,

INTERMEDIATE METAL CONDUIT, EMT WITH COMPRESSION FITTINGS IS NOT ACCEPTABLE.

17.C. TERMINATIONS: ALL EQUIPMENT PROVIDED ON THE PROJECT, INCLUDING PANELBOARDS AND

DISCONNECT SWITCHES, SHALL HAVE MANUFACTURER TERMINATIONS RATED AT 75°C.

17.D. CIRCUIT BREAKERS: CIRCUIT BREAKERS SHALL BE MOLDED CASE, THERMAL-MAGNETIC

QUICK-MAKE, QUICK-BREAK, BOLT-ON TYPE WITH MANUALLY OPERATED INSULATED TRIP-FREE

HANDLE. MULTI-POLE TYPES WITH INTERNAL COMMON TRIP BAR. TERMINALS SUITABLE FOR

COPPER CONDUCTORS.

17.E. DISCONNECT SWITCHES: DISCONNECT SWITCHES SHALL BE HEAVY-DUTY, ENCLOSED SAFETY

SWITCHES AS MANUFACTURED BY SIEMENS. SWITCHES SHALL BE OF THE QUICK-MAKE,

QUICK-BREAK TYPE WITH INTERLOCKING COVERS AND STEEL BOXES OF THE TYPE ENCLOSURE

REQUIRED FOR EACH LOCATION. SQUARE D, CUTLER HAMMER WILL BE CONSIDERED. MATCH BASE

BUILDING DISTRIBUTION EQUIPMENT.

17.F. OUTLET BOXES: OUTLET BOXES SHALL BE RECESSED MOUNTED AND SHALL BE CODE GAUGE STEEL

AND OF SIZE REQUIRED FOR SPECIFIC CONDITIONS.

18. LIGHTING FIXTURES AND LAMPS:

18.A. PROVIDE COMPLETE SYSTEM OF LIGHTING FIXTURES, LAMPS, ACCESSORIES AND SUPPORTS AS

SPECIFIED AND SHOWN. FOR TYPES, REFER TO SCHEDULE.

18.B. COORDINATE THE LIGHTING FIXTURE LAYOUT WITH THE ARCHITECTURAL REFLECTED CEILING PLAN.

ALL LIGHTING FIXTURES MOUNTED IN OR ON LAY-IN CEILING TILES SHALL BE LOCATED IN CENTER

OF TILE UNLESS OTHERWISE APPROVED BY ARCHITECT.

19. GROUNDING SYSTEM:

19.A. EQUIPMENT: GROUND NON-CURRENT CARRYING METAL PARTS OF THE ELECTRICAL SYSTEM.

PROVIDE A SEPARATE GREEN INSULATED EQUIPMENT GROUNDING CONDUCTOR WITH ALL FEEDERS AND BRANCH CIRCUITS, SIZED IN ACCORDANCE WITH THE OVERPROTECTIVE DEVICE SERVING THAT

FEEDER OR BRANCH CIRCUIT.

20. DEMOLITION:

20.A. DEMOLITION DRAWINGS ARE BASED ON ARCHITECTURAL PLANS, EXISTING PLANS AND FIELD

SURVEY. COORDINATE DEMOLITION WORK WITH ALL DISCIPLINES TO AVOID CONFLICTS.

20.B. FOR PLAN LINETYPE DESIGNATIONS OF REMOVED, RELOCATED, EXISTING AND NEW DEVICES REFER

TO THE ELECTRICAL SYMBOLS LIST.

20.C. DEVICES BEYOND REMODELED AREAS OF THIS CONTRACT THAT ARE WIRED THROUGH OR FROM

OUTLETS TO BE REMOVED OR ABANDONED SHALL REMAIN AND REMAIN OPERABLE.

20.D. REMOVE ALL ACCESSIBLE EXISTING CONDUIT INCLUDING FITTINGS, MOUNTING DEVICES, MOUNTING HARDWARE ETC. NOT BEING USED. PROVIDE CONDUIT CAPS FOR ALL ABANDONED CIRCUITS THAT

ARE TO REMAIN.

20.E. THE CONTRACTOR SHALL REMOVE THE CONDUIT FEEDING DEMOLISHED RECEPTACLES AND

ELECTRICAL DEVICES THAT ARE FED FROM UNDER THE FLOOR SLAB OR ARE EMBEDDED IN A WALL NOT SCHEDULED TO BE DEMOLISHED TO 2" BELOW EXISTING FLOOR LEVEL OR WITH THE WALL.

20.F. REMOVE ALL EXISTING WIRE AND CABLE NOT BEING USED.

20.G. WHERE EXISTING ELECTRICAL DEVICES ARE SHOWN BEING REMOVED AND JUNCTION BOXES ARE

NOT BEING RE-USED, REMOVE EXISTING WIRE AND CABLE, PROVIDE BLANK COVERPLATE.

20.H. ITEMS TO BE SALVAGED FOR REUSE OR DELIVERY TO OWNER SHALL BE PROTECTED AND STORED IN CONDITIONED SPACE BY CONTRACTOR UNTIL REUSED OR TRANSFERRED TO OWNER. PROVIDE A TYPEWRITTEN INVENTORY TO OWNER INCLUDING ALL ELECTRICAL DEVICES BEING REMOVED: I.E.

FIXTURES, SWITCHES, ETC. ALL MATERIALS REMOVED UNDER DEMOLITION THAT ARE NOT

DESIGNATED TO BE RETURNED TO THE OWNER SHALL BE PROPERLY AND LEGALLY DISPOSED FROM

THE PROJECT SITE.

20.I. ALL DEMOLITION WORK SHALL BE SCHEDULED AND COORDINATED AT TIMES CONVENIENT TO THE

OWNER OR BUILDING MANAGEMENT.

21. INSTALLATION:

21.A. SECURE ALL SUPPORTS TO BUILDING STRUCTURE. SUPPORT HORIZONTAL RUNS OF CONDUIT NOT MORE THAN 10 FEET APART. RUN EXPOSED RACEWAYS PARALLEL WITH OR AT RIGHT ANGLES TO

WALLS.

21.B. CUT CONDUIT ENDS SQUARE, REAM SMOOTH AND DRAW UP TIGHT WITH CONDUIT COUPLINGS.

PROVIDE NYLON BUSHING AT ALL OPEN CONDUIT ENDS.

21.C. LEAVE WIRE SUFFICIENTLY LONG TO PERMIT MAKING FINAL CONNECTIONS.

21.D. SET BOXES SQUARE AND TRUE WITH BUILDING FINISH.

21.E. ALL BRANCH CIRCUIT WIRING, CONDUIT AND FEEDERS SHALL BE INSTALLED CONCEALED BEHIND

BUILDING FINISHES UNLESS OTHERWISE NOTED.

21.F. ALL TELEPHONE/DATA CIRCUIT WIRING, AND CONDUIT SHALL BE INSTALLED CONCEALED BEHIND

BUILDING FINISHES UNLESS OTHERWISE NOTED.

21.G. COORDINATE LIGHT SWITCH LOCATIONS WITH DOOR SWINGS. SWITCHES SHALL BE INSTALLED ON

LATCH SIDE OF DOOR AS CLOSE AS POSSIBLE TO FRAME.

21.H. PROVIDE PULL STRING IN ALL EMPTY CONDUITS.

21.I. JUNCTION AND PULL BOXES: LOCATED GENERALLY NOT EXPOSED IN FINISHED SPACES WHERE

NECESSARY, REROUTE CONDUITS OR MAKE OTHER ARRANGEMENTS FOR CONCEALMENT. PROVIDE

PULL BOXES WHEREVER NECESSARY TO FACILITATE PULLING OF WIRE. COVERS OF JUNCTION AND

PULL BOXES SHALL BE ACCESSIBLE. COORDINATE LOCATIONS WITH OTHER TRADES. PROVIDE

CAST METAL JUNCTION BOXES FOR EXTERIOR LOCATIONS.

21.J. PROVIDE ACCESS PANELS IN ALL INACCESSIBLE CEILING SPACES, AS REQUIRED, BY THE NEC.

21.K. MAINTAIN CODE REQUIRED CLEARANCES FOR DISTRIBUTION EQUIPMENT AND DEVICES IN ALL

LOCATIONS.

21.L. ALL WALL, FLOOR, CEILING OR ROOF PENETRATIONS SHALL BE PERPENDICULAR SO THEY CAN BE

PROPERLY CAULKED AND/OR FIRE SEALED TO MAINTAIN THE RATING OF THE ASSEMBLY OR A

MINIMUM 2-HOUR RATING PENETRATION.

21.M. THE CIRCUIT NUMBERS ARE FOR IDENTIFICATION ONLY. HOMERUNS OF SIMILAR SINGLE PHASE CIRCUITS MAY BE COMBINED IN ONE CONDUIT WITH A COMMON NEUTRAL. PROVIDE NEUTRAL FOR EACH GFI CIRCUIT. ONLY THREE SINGLE PHASE CIRCUITS (120V OR 277V) MAY BE COMBINED IN ANY

ONE CONDUIT. ON COMPLETION OF THE PROJECT, BALANCE THE PANEL LOAD UNDER NORMAL

OPERATING CONDITIONS. (MAXIMUM 10% DEVIATION BETWEEN PHASES).

21.N. 120 VOLT BRANCH CIRCUITS OVER 100 FEET FROM PANEL TO FIRST OUTLET SHALL HAVE

CONDUCTORS ONE SIZE LARGER THAN INDICATED WHETHER INDICATED IN THE PANEL SCHEDULE

OR NOT.

21.O. THE QUANTITY OF WIRES MAY NOT BE INDICATED FOR ALL CIRCUITS. ONLY THOSE WHERE CLARIFICATION IS NECESSARY ARE INDICATED. PROVIDE ALL WIRES NECESSARY FOR THE PROPER

FUNCTION OF THE SYSTEM WHETHER INDICATED ON PLANS OR NOT.

21.P. ALL EQUIPMENT, SUCH AS STARTERS, RELAYS, CONTACTORS, SWITCHES, PANELS, AND OTHER DISTRIBUTION EQUIPMENT SHALL HAVE IDENTIFICATION PLATES OF BLACK LAMINATED PLASTIC WITH 1/2" WHITE LETTERS. EQUIPMENT IDENTIFICATION SHALL MATCH THE CONTRACT DOCUMENTS.

21.Q. ELECTRICAL METALLIC TUBING SHALL BE USED FOR EMERGENCY AND LIFE SAFETY LOADS.

21.R. ALL PHASE LOADS ON PANELBOARDS (NEW AND EXISTING) THAT ARE PART OF THE SCOPE OF WORK

SHALL BE BALANCED AND MAXIMUM DIFFERENCE SHALL NOT EXCEED 10 PERCENT.

21.S. LABEL CIRCUIT NUMBERS IN BACK BOXES OF ALL DEVICES.

21.T. INSTALL DIGITAL LIGHTING CONTROL SYSTEM IN ACCORDANCE WITH APPROVED SHOP DRAWINGS

AND MANUFACTURER'S INSTRUCTIONS.

CO

VE

R

SH

EE

T

- E

LE

C

10/24/210/29/2512/19/25 z m an

C on su lti ng G ro up

L td

W or ld ga te

D riv e

S ui te

H er nd on

, V A

P ho ne

3)

-0

F ax

3)

-9

LE

VE

LS

B

AS

EM

EN

T, ST

, 2 N

D

TO

W

N

HA

LL

B

AT

HR

O O

M R

EN

O

VA

TI

O N

PROJECT NO

140339-01-003

09.23.2025

FILE NO

bo w m an

.c om

B ow m an

C on su lti ng G ro up

L td

J:\T\140339-01-003 Town Hall Bathroom Reno…