TR-1075_Datasheet_090407.pdf

The Massa Model TR-1075 Family consists of rugged high-power under-water transducers designed to operate in the 2.5 to 10 KHz frequency range. They are ideal for use in bottom mapping and sub-bottom profiling applications.

The transducers are designed to be driven with a maximum input power of 600 Watts using up to a 30% duty cycle, or 200 Watts maximum for continuous operation. In shallow water, the maximum output is cavita-tion limited. Minimum water depths of approximately 30 and 100 feet are recommended for input power of 200 and 600 Watts respectively to avoid cavitation.

All of the transducers in the family utilize the same resonant structure containing a circular piston for the radiating source that is ½ wavelength in diameter at 4 KHz. The transducers are designed to be bolted directly through their 4-corner integral shock mounts to a simple frame structure. This modular design allows the transducers to easily be assembled into arrays to achieve any desired beam pattern and source level. Each transducer is terminated with a Massa C1F2 Female Underwater Connector and has a locking ring included. Mating C1M2 Male Connectors can be purchased separately.

The TR-1075E consists of the basic resonator with no electrical tuning.

Its nominal frequency of resonance is 3.5 KHz. Massa has fabricated TR-1075 Transducers with a wide variety of different internal tuning networks. They have included transformers to produce different output impedance magnitudes. Transducers have been made with both series and parallel tuning to produce a nominal phase angle of 0 at different frequencies. A separate inductor is required for series tuning, while the inductance of the primary windings of the transformer is used for parallel tuning.

In some cases, damping resistors have been connected across the transducer to lower its Q, which allows the use of a short tone burst excitation pulse with reduced sensitivity for operation when very close to the sea floor. These transducers can be driven with greater input power because some of the energy is dissipated by the resistor. Massa can customize a tuning network to meet any requirement, but one of the standard models will usually meet the needs of most customers.

FEATURES

� High Power

- Up to 600 Watts @ 30% Duty Cycle

- Up to 200 Watts CW

� Broadband

- 2.5 to 10 kHz

� MaximumOperating Depth is 2,000 ft.

� True Piston Radiating Source

- 1/2 Wavelength Diameter at 4 kHz

- 80° Conical Beam Angle

� Module Design

- Shock Mounted

- Easily Assembled into

Arrays

� Weight is 25 lbs.

� Terminated with Proven Reliable C1F2 Underwater Connector

� Mates to Massa C1M2 Underwater Connector

APPLICATIONS

� Sub-Bottom Profiling

� Bottom Mapping

Massa TR-1075 Sub-Bottom Profiling Transducers

Page 1 of 4 090407

TR-1075 Transducer Family Outline Drawing (Dimensions in Inches)

Massa TR-1075 Data

Page 2 of 4 All Specifications subject to change without notice. 090407

Chart Showing the Tuning Circuits for the Standard Models of the TR-1075 Transducer Family

Transducer Model

Number

Frequency Tuned for 0° Phase

(nominal)

Impedance Magnitude (nominal)

Power Rating % Duty Cycle Tuning Circuit

TR-1075E No Tuning 4,500 Ohms @ 3.5 kHz

600 Watts @ 30% 200 Watts @ 100%

No Tuning

TR-1075A 4 kHz 100 Ohms @ 4 kHz

600 Watts @ 30% 200 Watts @ 100%

Parallel

TR-1075H 3.5 kHz 250 Ohms @ 3.5 kHz

600 Watts @ 30% 200 Watts @100%

Series

TR-1075D 3.5 kHz 200 Ohms @ 3.5 kHz

1,000 Watts @ 30% 335 Watts @ 100%

Series with Shunt Resistor

MASSA PRODUCTS CORPORATION

Page 3 of 4 All Specifications subject to change without notice. 090407

Transmitting Voltage Responses

Receiving Voltage Sensitivities

Impedance Magnitudes

Massa TR-1075 Nominal Response Curves

Massa C1M2 male and C1F2 female 2-conductor in-line Underwater Connectors were developed for the oceanographic community to provide highly reliable underwater connection. Massa has manufac-tured and sold over 100,000 connector pairs, and some have been successfully used for over 20 years in the ocean. There has never been a failure of a connector reported to Massa.

Massa typically supplies transducers with C1F2 Female Connectors attached. C1M2 Male Connectors can be purchased separately to complete the mating connection. The standard C1M2 is attached to a 5 foot cable with a retaining ring included, but connectors can be fabricated with any length of cable required.

Massa C1M2/C1F2 Underwater Connectors

090407

MASSA PRODUCTS CORPORATION

280 Lincoln St., Hingham, MA 02043 U.S.A.

Tel: 781-749-4800 Fax: 781-740-2045 Toll Free in USA: 800-962-7543

E-mail: sales@massa.com Web Site: www.massa.com

Photograph of C1M2 and C1F2 Connectors with Retaining Rings