Drawings.pdf

OF SUPPLY AND WASTE LINES.

ESCUTCHEONS. ESCUTCHEONS SHALL BE PROVIDED AT ALL WALL PENETRATIONS

ALL PLUMBING FIXTURES ABOVE SHALL HAVE CHROME PLATED FINISH ON ALL

EXPOSED SUPPLY PIPING, VALVE STOPS, TAILPIECES, P-TRAPS, AND

COMPLETE INSTALLATION COMPLY WITH ALL ADAABAAG REQUIREMENTS.

CONTRACTOR SHALL VERIFY THAT ALL HANDICAPPED FIXTURES, ROUGH-INS AND

WATER HAMMER ARRESTOR WHA

BOTH CONTRACTOR AND ARCHITECT.

4. OR A WRITTEN REQUEST FROM THE ARCHITECT FOR MINOR

CHANGES TO REQUIRED WORK.

COSTS OF ALL WORK REJECTED BY THE ARCHITECT FOUND TO BE

DEFECTIVE OR NON-COMPLYING TO CONTRACT DOCUMENTS WHETHER

OR NOT FABRICATED, INSTALLED, OR COMPLETED.

NOTIFY THE ARCHITECT IN WRITING, A MINIMUM OF SEVEN (7)

CALENDAR DAYS PRIOR TO ANY WORK BEING COVERED. IF ANY

PORTION OF THE WORK SHOULD BE COVERED CONTRARY TO THE

THE ARCHITECTS OBSERVATION, AND SHALL BE REPLACED AT THE

SYSTEMS TO BE OBSERVED PRIOR TO COVERING:

1. SOIL, WASTE AND VENT PIPING.

3. DOMESTIC COLD AND HOT WATER PIPING.

1. A WRITTEN AMENDMENT TO THIS DOCUMENT AND SIGNED BY

3. A WRITTEN INTERPRETATION OF THE DOCUMENTS ISSUED BY THE

THE CONTRACTOR SHALL PROMPTLY CORRECT AND BEAR ALL ASSOCIATED

OBSERVED BEFORE, OR AFTER SUBSTANTIAL COMPLETION, AND WHETHER

ANY PORTION OF THE WORK TO BE COVERED MAY BE OBSERVED BY

THE ARCHITECT PRIOR TO COVERING OF WORK. CONTRACTOR SHALL

REQUIREMENTS SPECIFICALLY EXPRESSED IN THE CONTRACT DOCUMENTS,

IT MUST, IF REQUIRED IN WRITING BY THE ARCHITECT, BE UNCOVERED FOR

ALL AUTOMATIC OR SELF-CLOSING VALVES FOR FAUCETS SHALL BE ADJUSTED

IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS AND SUPERVISED,

AS NECESSARY, BY EQUIPMENT SUPPLIER'S REPRESENTATIVE AT THE REQUEST

ARCHITECT.

2. A CHANGE ORDER.

CONTRACTORS EXPENSE.

2. ROOF DRAINAGE PIPING.

4. FIRE PROTECTION PIPING.

OF THE ARCHITECT OR ENGINEER.

SYMBOL

THE CONTRACT DOCUMENTS.

GENERAL PLUMBING NOTE:

GOVERNING CODES PROVIDE MINIMUM REQUIREMENTS AND MAY NOT

MODIFICATION TO THE CONTRACT DOCUMENTS MAY OCCUR AS:

NECESSARILY MEET HIGHER STANDARD REQUIREMENT OF THE CONTRACT

DOCUMENTS: THEREFORE THE CONTRACTOR SHALL NOT BE RELIEVED OF

THE RESPONSIBILITY FOR ANY DEVIATION FROM THE REQUIREMENTS OF

LEGEND

DESCRIPTION ABBREVIATION

PER CURRENT UNIFORM PLUMBING CODE.

PROVIDE WATER HAMMER ARRESTOR FOR BOTH CW AND HW SUPPLY LINES

VTR

NG

NG

BRANCH - TOP CONNECTION

VENT THRU ROOF

BRANCH - SIDE CONNECTION

BRANCH - BOTTOM CONNECTION

VTR

SOIL, WASTE OR SANITARY SEWER

GAS PRESSURE REGULATOR

CLEAN-OUT TO GRADE WITH

CONCRETE COLLAR

GAS COCK, GAS STOP

RECESSED BOX WALL HYDRANT

HOSE BIB

UNION (SCREWED)

CAPPED OR PLUGGED TEE

BALL VALVE

GATE VALVE

NATURAL GAS - LOW PRESSURE (7"W.C.)

HOT WATER (120°F OR BELOW)

COLD WATER

VENT (SANITARY, GREASE, ETC.)

RISE OR DROP

RISER UP (ELBOW)

RISER DOWN (ELBOW)

VALVE IN RISER (TYPE AS SPECIFIED OR NOTED)

FLOW - IN DIRECTION OF ARROW

HB

WH

SAS

NG

HW

CW

V

HOT WATER RETURN HWR

STORM SEWER (ROOF DRAINAGE) SSSS

GREASE WASTE GWGW

GENERAL FIRE STOPPING NOTE

ALL PIPE PENETRATIONS OF FIRE RATED WALLS AND FLOORS SHALL BE

PROTECTED WITH APPROVED FIRE STOPPING ASSEMBLIES AS MANUFACTURED

BY 3M INDUSTRY, OR APPROVED EQUAL. THE ASSEMBLIES SHALL COMPLY

WITH LATEST APPLICABLE REQUIREMENTS OF UBC CODE, NFPA 13 AND

OWNER INSURANCE. PROPOSED APPLICABLE ASSEMBLIES SHALL BE UL

LISTED AND SHALL BE PART OF THE PLUMBING EQUIPMENT SUBMITTAL.

INSULATION NOTE

REQUIREMENTS FOR INSULATION (2021 UPC - 609.12.1 AND 609.12.2:

ALL HOT WATER LINES SHALL BE INSULATED. HW PIPE INSULATION SHALL HAVE A MINIMUM

COLD WATER LINES SHALL BE INSULATED THE SAME AS HOT WATER AS REQUIRED:

COLD WATER LINES LOCATED IN EXTERIOR WALLS SHALL BE INSULATED.

COLD WATER LINES LOCATED IN NON-RETURN AIR PLENUMS SHALL BE INSULATED.

COLD WATER LINES LOCATED IN RETURN AIR PLENUMS OR INTERIOR WALL CAVITIES

ARE NOT REQUIRED TO BE INSULATED.

ALL ROOF DRAIN LINES SHALL BE INSULATED MATCHING HOT WATER REQUIREMENTS.

MAY BE SLOPED AT 1/8" PER FOOT OR 1 PERCENT IF CONDITIONS OF UPC 2021 SECTION 708.0 ALL WASTE PIPE SHALL BE SLOPED 1/4" PER FOOT OR 2 PERCENT, 4" AND LARGER WASTE PIPE

SANITARY SEWER NOTE

ARE MET AND APPROVED BY THE AUTHORITY HAVING JURISDICTION.

THICKNESS OF NOT LESS THAN THE DIAMETER OF THE PIPE FOR PIPES UP TO 2" DIAMETER.

PIPES 2" AND LARGER SHALL BE INSULATED WITH NOT LESS THAN 2" WALL THICKNESS.

PLUMBING PIPE SCHEDULE

SERVICE SCHEDULE

DOMESTIC COLD WATER COPPER TYPE L

MATERIAL OR JOINT TYPE

BRAZED OR SOLDERED*

CONNECTION

DOMESTIC HOT WATER COPPER TYPE L BRAZED OR SOLDERED*

DOMESTIC HW RECIRC. COPPER TYPE L BRAZED OR SOLDERED*

NATURAL GAS BLACK STEEL SCH. 40 WELDED OR THREADED

SANITARY SEWER PVC (BELOW SLAB) SCH. 40 DWV SOLVENT WELD

VENT PVC (BELOW SLAB) SCH. 40 DWV SOLVENT WELD

VENT PVC OR CAST IRON (ABOVE SLAB) SCH. 40/DWV SOLV. WELD OR NO-HUB

COMMENTS

INSULATED PER NOTE

INSULATED PER NOTE

INSULATED PER NOTE

SANITARY SEWER PVC OR CAST IRON (ABOVE SLAB)

1) PIPE SCHEDULE FOR INFORMATION ONLY; SEE MATERIAL AND SERVICE SPECIFICATIONS FOR MATERIAL, STANDARDS, INSTALLATION, AND QUALIFICATIONS.

2) *WHERE COPPER PIPING IS CALLED FOR ON WATER LINES, "PRESS-FIT" COPPER TUBING CAN BE USED, WITH

EPDM SEALS.

3) *WHERE COPPER PIPING IS CALLED FOR ON WATER LINES, PEX TUBING CAN BE SUBSTITUTED .

CAST IRON (PLENUM)

PVC (NON-PLENUM)

SCH. 40/DWV SOLV. WELD OR NO-HUB

CAST IRON (PLENUM)

PVC (NON-PLENUM)

SEE PLUMBING SPECIFICATIONS FOR ADDITIONAL INFORMATION

PLUMBING SPECIFICATIONS:

1. GENERAL:

A. PROVIDE ALL NECESSARY LABOR, MATERIALS, EQUIPMENT, SERVICES AND INSURANCES TO COMPLETE THE PLUMBING

WORK WITHIN THE FULL INTENT OF THE DRAWINGS AND SPECIFICATIONS CONTAINED HEREON. PLUMBING CONTRACTOR

SHALL PROVIDE ALL NECESSARY PERMITS AND FEES.

B. ALL WORK SHALL BE IN ACCORDANCE WITH ALL APPLICABLE CODES, RULES AND LOCAL REQUIREMENTS.

C. GUARANTEE ALL WORK AND MATERIALS FOR A PERIOD OF ONE YEAR UNLESS NOTED OTHERWISE.

D. DRAWINGS ARE DIAGRAMMATIC AND SHOW BASIC SIZING. CONTRACTOR TO COORDINATE THE ROUTING OF ALL NEW

PIPING ABOVE THE CEILING WITH EXISTING/NEW DUCTWORK, PIPING, LIGHTING, STRUCTURE, ETC.

E. ANY MAJOR RE-ROUTING SHALL BE BROUGHT TO THE ATTENTION OF THE OWNER'S REPRESENTATIVE FOR APPROVAL.

2. DESCRIPTION OF WORK:

A. PROVIDE AND INSTALL WATER, WASTE, CONDENSATE, AND VENT PIPING, VALVES, PLUMBING FIXTURES, WATER HEATERS, AND ACCESSORIES, AS INDICATED.

3. SUBMITTALS:

A. FURNISH SUBMITTALS FOR ALL BUT NOT LIMITED TO THE FOLLOWING ITEMS:

a. PLUMBING FIXTURES,

b. WATER HEATERS,

c. PLUMBING FIXTURE BRASS AND SPECIALTIES,

d. PLUMBING PIPING,

e. INSULATION,

f. HANGERS AND SUPPORTS.

4. PIPING:

A. SANITARY SEWER AND VENT PIPING BELOW GRADE: ABS PIPE OR SCH 40 PVC. ABS PIPE SHALL BE ASTM D2661-2014

WITH ABS FITTINGS. JOINTS SHALL BE ASTM D2235-2016, SOLVENT WELD. PVC PIPE SHALL BE ASTM D2666-2017.

FITTINGS SHALL BE PVC ASTM D2855-2015 SOLVENT WELD WITH ASTM D2564-2018 SOLVENT CEMENT.

B. SANITARY SEWER AND VENT PIPING ABOVE GRADE: SERVICE WEIGHT CAST IRON CISPI 301, HUBLESS, SERVICE

WEIGHT. FITTINGS: CAST IRON. JOINTS: NEOPRENE GASKETS AND STAINLESS STEEL CLAME-AND-SHIELD

ASSEMBLIES. FITTINGS LOCATED WITHIN FIRE RATED WALLS MUST HAVE FULL COVERAGE SHIELDS APPROVED

FOR SUCH USE.

C. ALL VENT PIPING LOCATED ABOVE CEILING SHALL HAVE MIN. 2% SLOPE OR AS APPROVED BY THE

ENGINEER.

D. DOMESTIC WATER PIPING SHALL BE TYPE "L" HARD DRAWN COPPER WITH WROUGHT COPPER FITTINGS. USE 100% LEAD

FREE SOLDER ON PIPING 2'' AND UNDER AND SILVER BRAZED JOINTS ON PIPING OVER 2''. OMIT BRAZED JOINTS ON ANY

THREAD ADAPTERS AND CAST VALVES AND FLANGES - USE 95/5.

E. CONDENSATE DRAIN PIPING FOR FOR HVAC SYSTEMS SHALL BE TYPE "M" HARD DRAWN COPPER WITH WROUGHT

COPPER FITTINGS. COORDINATE INSTALLATION WITH ALL OTHER TRADES. PROVIDE END OF LINE CLEANOUTS AT EVERY

90 DEGREE ELL. COORDINATE INSTALLATION WITH THE MECHANICAL CONTRACTOR.

F. ALL HOT WATER STOPS AND TRAP PIPING LOCATED BELOW EACH LAV SHALL BE INSULATED WITH PRODUCTS AS

INDICATED.

G. CONCEAL ALL PIPING WHERE POSSIBLE.

H. ALL FITTINGS SHALL BE ACCEPTED FITTINGS FOR THE APPLICATION.

I. INSTALL SUFFICIENT HANGERS ON ALL HORIZONTAL PIPING NOT OVER 4 FEET APART AND AT ALL TURNS. PIPING SHALL

HAVE SUFFICIENT HANGERS TO KEEP SYSTEMS IN ALIGNMENT. ANCHOR PIPING AS REQUIRED.

J. INSTALL FIRST QUALITY BALL VALVES DESIGNED FOR THE APPLICATION. KITZ AND NIBCO ARE ACCEPTABLE

MANUFACTURER'S. VAVLES SHALL BE BRASS FULL PORT, TWO PIECE BLOW OUT PROOF, LEVER HANDLE SCREWED OR

SOLDER JOINT MAY BE USED IN LIEU OF GATE VALVE UNDER 2'' SIZE.

K. ALL NEW PIPING SHALL BE DOMESTIC. FORIEGN PIPING WILL NOT BE ALLOWED.

5. OTHER MATERIAL:

A. ALL OTHER MATERIAL, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR A COMPLETE JOB, SHALL BE NEW AND FIRST

QUALITY, FURNISHED AND INSTALLED BY THE PLUMBING CONTRACTOR.

6. WORKMANSHIP:

A. ALL WORK TO BE PERFORMED BY QUALIFIED PERSONNEL NORMALLY ENGAGED IN THE RESPECTIVE LINE OF WORK.

B. THIS CONTRACTOR IS RESPONSIBLE FOR PERFORMING ALL WORK ACCEPTABLE TO THE OWNER'S REPRESENTATIVE.

C. ENSURE THE EXPOSED ENDS OF ALL PLUMBING PIPING ARE PROVIDED WITH TEMPORARY CAPS DURING CONSTRUCTION.

7. SUPPORT:

A. SUPPORT ALL WATER AND VENT PIPING IN PLUMBING WALLS WITH HOLD-RITE PIPE SUPPORT SYSTEM OR EQUAL. ENSURE

ALL VERTICAL COPPER WATER PIPING WITHIN WALLS ARE TIGHTLY SECURED (LOSE PIPING INSTALLATION WILL NOT BE

ACCEPTED).

B. ALL PIPING AT FLUSH VALVES TO BE HELD SECURELY IN PLACE TO PREVENT MOVEMENT IN ANY DIRECTION.

C. ALL PIPING SERVING FAUCET SET AT THE SERVICE SINK TO BE HELD SECURELY IN PLACE TO PREVENT MOVEMENT IN ANY

DIRECTION.

8. ISOLATION:

A. ISOLATE ALL DISSIMILAR METALS WITH ISOLATORS EQUALING OR EXCEEDING THE QUALITY OF "EPCO" DIELECTRIC

UNIONS.

B. ISOLATE ALL COPPER PIPING FROM DISSIMILAR SUPPORTS.

C. ISOLATE ALL PIPING THROUGH CONCRETE WITH 1/2'' CLOSED CELL FOAM.

D. ISOLATE ALL PIPING AT STUDS WITH POLYETHYLENE PIPE INSULATORS MODEL P.I. AS MANUFACTURED BY SPECIALTY

PRODUCTS COMPANY OR EQUAL.

9. CUTTING AND PATCHING:

A. ALL WORK SHALL BE DONE BY QUALIFIED PERSONNEL NORMALLY ENGAGED IN THE RESPECTIVE WORK REQUIRED.

B. CUTTING OF ALL OPENINGS AT THE EXISTING SHELL BUILDING SHALL BE COORDINATED WITH THE GENERAL

CONTRACTOR.

10. TEST AND CHLORINATION:

A. ALL PIPING SHALL BE TESTED IBEFORE WORK IS CONCEALED. NOTIFY THREE DAYS PRIOR TO TESTS.

B. FLUSH ALL PIPING TO REMOVE ANY FOREIGN MATERIAL.

C. CHLORINATE ALL NEW WATER PIPING PRIOR TO USE FOR 24-HOUR PERIOD WITH A MINIMUM OF 50 PARTS PER MILLION OR

AS REQUIRED TO ACHIEVE A CHLORINE RESIDUAL OF 10 MILLIGRAMS PER LITER AT COMPLETION OF A 24-HOUR PERIOD.

ALL PROCEDURES SHALL BE IN ACCORDANCE WITH AWWA STANDARD C651 AND THE STATE HEALTH DEPARTMENT.

D. TEST NEWLY INSTALLED WATER PIPING PRIOR TO PROJECT CLOSEOUT IN ACCORDANCE WITH THE FOLLOWING

SCHEDULE:

WATER 100 P.S.I. W/WATER 24 HOURS

WASTE AND VENT 10' HIGH WATER COLUMN.

MK DATE DESCRIPTION

A1816.33

DECEMBER 09, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

01/22/2025

24568

GA

BR I EL A . LOWE

NEW MEX I CO

P

RO

F E S S I O NA L E NG I N E E R

P-001

PLUMBING

INFORMATION

HRM GL

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

A015

HALL

A016

OFFICE

A017

OFFICE

A001

CORRIDOR

A024

COURT

CLINICIAN

A023

ADMIN.

STORAGE

UP

UP TO

GROUND

LEVEL

EXISTING

STAIRS

EXISTING

HALLWAY

MK DATE DESCRIPTION

A1816.33

DECEMBER 09, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

01/22/2025

24568

GA

BR I EL A . LOWE

N

EW MEX I CO

P

RO

F E S S I O NA L E NG I N E E

R

4' 8'2'0

SCALE: 1/4" = 1'-0"

TRUE

NORTH

PROJECT

NORTH

PD-102

PLUMBING

DEMOLITION

FLOOR PLAN

BASEMENT LEVEL

HRM GL

A. THESE DRAWINGS REFLECT INFORMATION GATHERED BY SITE

INSPECTION AND PREVIOUS CONSTRUCTION DRAWINGS. IT IS POSSIBLE

THAT THE EXACT LOCATION OF PIPING AND EQUIPMENT MAY BE

DIFFERENT FROM LOCATIONS SHOWN ON THE DRAWINGS. PRIOR TO

BIDDING THE CONTRACTOR SHALL MAKE SITE VISIT TO REVIEW BUILDING

CONDITIONS AND REQUIREMENTS.

B. IN THE EVENTS OF UNFORESEEN CONDITIONS THE CONTRACTOR SHALL

NOTIFY THE ARCHITECT OR OWNER AND PROVIDE THE DOCUMENTATION

NECESSARY FOR RESOLUTION.

C. OWNER SHALL HAVE FIRST RIGHT FOR REFUSAL OF ANY REMOVED

EQUIPMENT.

D. THE OWNER IS ENTITLED TO SALVAGE AND OR REMOVE HARDWARE,

FIXTURES, AND EQUIPMENT FROM ALL AREAS OF THIS CONTRACT PRIOR

TO DEMOLITION.

E. EXISTING REMOVED EQUIPMENT AND MATERIALS SHALL BE REMOVED

FROM SITE AND DISPOSED OF BY CONTRACTOR PER STATE

REGULATIONS.

F. THE TERM "REMOVE" MEANS "REMOVE AND FULLY DISPOSED OF"

UNLESS NOTED OTHERWISE.

G. AT THE END OF THE PROJECT THE CONTRACTOR SHALL PROVIDE A

COMPLETE AS-BUILTS SET OF DRAWINGS.

1 COORDINATE UNITS WITH MECHANICAL WORK. DISCONNECT EXISTING

CONDENSATE DRAINS IF NEEDED. FIELD VERIFY EXISTING CONDITIONS.

AutoCAD SHX Text

PLUMBING DEMOLITION PLAN - BASEMENT LEVEL

AutoCAD SHX Text A1

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

GENERAL INFORMATION

AutoCAD SHX Text

KEY PLAN

KEYED NOTES

A016

OFFICE

A017

OFFICE

A001

CORRIDOR

A024

COURT

CLINICIAN

A023

ADMIN.

STORAGE

UP

UP TO

GROUND

LEVEL

EXISTING

STAIRS

EXISTING

HALLWAY

OFFICE

WORK

ROOM

OFFICE

OFFICE

MK DATE DESCRIPTION

A1816.33

DECEMBER 09, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

01/22/2025

24568

F E S S I O NA L E NG I NE E R

4' 8'2'0

SCALE: 1/4" = 1'-0"

TRUE

NORTH

PROJECT

NORTH

P-102

PLUMBING

ENLARGED

FLOOR PLAN

BASEMENT LEVEL

HRM GL

A PLUMBING PLANS ARE GENERALIZED AS TO THE OVERALL INTENT OF THE

PLUMBING WORK REQUIRED FOR NEW CONSTRUCTION INCLUDING

PLUMBING FIXTURES, HANGERS AND SUPPORTS, PIPING, EQUIPMENT,

ETC.

1 COORDINATE ALL HVAC UNITS WITH MECHANICAL. RECONNECT AND

REROUTE CONDENSATE DRAINS AS NEEDED. FIELD VERIFY CONDITIONS.

AutoCAD SHX Text

SSE-3

AutoCAD SHX Text 282cfm

AutoCAD SHX Text

SSE-2

AutoCAD SHX Text 282cfm

AutoCAD SHX Text

(E) SSE

AutoCAD SHX Text

AutoCAD SHX Text

(E) SSE

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

PLUMBING ENLARGED FLOOR PLAN - BASEMENT LEVEL

AutoCAD SHX Text A1

AutoCAD SHX Text

GENERAL NOTES

AutoCAD SHX Text

KEY PLAN

1. EQUIPMENT CAPACITIES BASED ON OPERATION AT SITE ELEVATION.

2. DUCT DIMENSIONS SHOWN ON DRAWINGS ARE NET INSIDE DIMENSIONS.

3. EXACT LOCATION OF ALL GRILLES, DIFFUSERS, AND REGISTERS SHALL BE COORDINATED WITH LIGHTING AND REFLECTED CEILING PLANS. WHERE INSTALLATIONS CONFLICT, FINAL LOCATION

SHALL BE APPROVED AND OBTAINED FROM ARCHITECT.

4. PROVIDE TURNING VANES IN ALL SQUARE (90 DEGREE) ELBOWS (EXCEPT R.A. DUCTWORK).

5. EACH ROUND BRANCH TAKE-OFF SHALL BE MADE WITH SPIN-IN DAMPER FITTING.

6. INSTALL SEISMIC BRACING AS REQUIRED ON ALL DUCT AND EQUIPMENT PER THE SEISMIC DESIGN CATEGORY AND IMPORTANCE FACTOR LISTED IN STRUCTURAL DRAWINGS.

7. JOINTS AND SEAMS ON LOW VELOCITY SUPPLY, RETURN AND EXHAUST DUCTS, ROUND OR RECTANGULAR, MUST BE SEALED AIR TIGHT.

8. CONTRACTOR SHALL COORDINATE AIR CONDITIONING DUCTWORK, PLUMBING, AND SPRINKLER PIPING WITH OTHER TRADES, TO AVOID CONFLICTS AND MAINTAIN EQUIPMENT ACCESS AND

SERVICEABILITY TO VALVES AND EQUIPMENT.

9. CONTRACTOR SHALL FURNISH ALL NECESSARY STRUCTURES, INSERTS, SLEEVES, AND HANGING DEVICES FOR INSTALLATION OF MECHANICAL AND PLUMBING EQUIPMENT, DUCTWORK AND PIPING, ETC.

CONTRACTOR SHALL COORDINATE INSTALLATION OF SUCH DEVICES WITH GENERAL CONTRACTOR. CONTRACTOR MUST FURTHER VERIFY WITH THE STRUCTURAL ENGINEER THAT THE DEVICES ARE ADEQUATE AS INTENDED AND DO NOT OVERLOAD THE BUILDING'S STRUCTURAL COMPONENTS IN ANY WAY.

11. EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS.

12. PROVIDE ALL NECESSARY FITTINGS FOR RISES AND OFFSETS IN DUCTWORK AND PIPING, WHETHER OR NOT SHOWN, FOR PROPER INSTALLATION. PROVIDE BALANCING DAMPERS AT EACH BRANCH

TAKEOFF.

13. DUCT GAUGE SHALL BE PER SMACNA SPECIFICATIONS.

15. PROVIDE FIRE DAMPERS IN ALL FIRE RATED WALL DUCT PENETRATIONS. PROVIDE FIRESTOPPING AT ALL FIRE WALL PENETRATIONS.

16. CONTRACTOR SHALL PROVIDE RETURN AIR OR TRANSFER AIR OPENINGS IN CEILING SPACE AT FULL HEIGHT WALLS TO CREATE AND/OR MAINTAIN A RETURN AIR PATH. FIRE/SMOKE DAMPERS SHALL BE

PROVIDED IN SUCH OPENINGS WHERE REQUIRED. COORDINATE THE LOCATIONS OF ALL DUCTWORK WITH ANY PLUMBING LINES AND ELECTRICAL CONDUIT.

17. IN THE EVENT THAT ANY DUCT CANNOT BE ROUTED AS SHOWN ON THE CONTRACT DRAWINGS, THE CONTRACTOR SHALL MODIFY THE DUCT AS REQUIRED, MAINTAINING THE SAME NET FREE AREA AS

THE DESIGNED DUCT. CONTRACTOR SHALL SUBMIT SHOP DRAWINGS SHOWING THE PROPOSED CHANGES FOR APPROVAL. THIS SHALL BE DONE AT NO COST TO THE OWNER.

18 THERMOSTATS SHALL BE WALL MOUNTED 4'-0" ABOVE FINISHED FLOOR. COORDINATE THE LOCATION OF ALL ROOF AND FLOOR PENETRATIONS WITH EXISTING STRUCTURAL CONDITIONS.

19. FRAME AROUND EACH PENETRATION PER ARCHITECTURAL / STRUCTURAL DRAWINGS.

20. DUCTWORK CONNECTIONS TO ALL AIR HANDLING EQUIPMENT SHALL BE MADE WITH WEATHERPROOF FLEXIBLE CONNECTIONS.

21. INSULATE EXPOSED EXTERIOR DUCTWORK WITH 1.5" FIBERGLASS DUCTWRAP INSULATION (R4) WITH VAPOR BARRIER, AND COVER WITH 0.016" EMBOSSED ALUMINUM JACKET.

22. INSULATE CONCEALED SUPPLY DUCTWORK WITH PLENUM RATED 1.5" FIBERGLASS DUCTWRAP INSULATION (R4) WITH VAPOR BARRIER.

GENERAL NOTES

1. GENERAL:

A. PROVIDE ALL NECESSARY LABOR, MATERIALS, EQUIPMENT, SERVICES

AND INSURANCES TO COMPLETE THE AIR CONDITIONING WORK WITHIN

THE FULL INTENT OF THE DRAWINGS AND SPECIFICATIONS CONTAINED

HEREIN AND TO THE COMPLETE SATISFACTION OF THE

ARCHITECT/ENGINEER.

B. ALL WORK SHALL BE IN ACCORDANCE WITH ALL APPLICABLE CODES,

RULES AND LOCAL REQUIREMENTS.

C. AIR CONDITIONING WORK SHALL BE IN ACCORDANCE WITH THE 2021

EDITION OF THE I.B.C., U.M.C., U.P.C., IECC, AND ALL APPLICABLE CODES,

RULES AND LOCAL REQUIREMENTS.

D. GUARANTEE ALL WORK AND MATERIALS FOR A PERIOD OF ONE YEAR.

2. SUBMITTALS:

A. SPECIFICATION SHEETS WILL BE REQUIRED ON ALL NEW EQUIPMENT TO

BE INSTALLED AND SHALL BE PRESENTED TO THE OWNER'S

REPRESENTATIVE BEFORE INSTALLATION. FURNISH SUBMITTALS FOR:

a. ROOFTOP UNITS AND EVAPORATIVE COOLERS

b. EXHAUST FANS

c. DUCTWORK , HANGERS, AND INSULATION

d. AIR DISTRIBUTION DEVICES

e. CONTROL DEVICES

3. EQUIPMENT:

A. ALL EQUIPMENT SHALL BE AS SCHEDULED ON DRAWINGS.

B. AT CONTRACTORS OPTION, EQUIPMENT OF EQUAL QUALITY,

CONSTRUCTION AND CAPACITIES CAN BE SUBMITTED FOR APPROVAL.

CONTRACTOR MUST SUBMIT AN ITEM-BY-ITEM LIST OF CAPACITY AND

CONSTRUCTION FEATURES TO SHOW THAT SUBSTITUTED EQUIPMENT IS

EQUAL OR BETTER THAN THAT SPECIFIED.

C. THE CONTRACTOR IS RESPONSIBLE FOR ALL REQUIRED MECHANICAL,

ARCHITECTURAL, STRUCTURAL AND ELECTRICAL CHANGES NECESSARY

TO ACCOMMODATE THE SUBSTITUTED EQUIPMENT.

4. HVAC WORK:

A. ADHERE TO GENERAL ROUTING AND METHODS OF DISTRIBUTION SHOWN,

FURNISHING ALL LABOR AND MATERIALS AND APPURTENANCES AS

REQUIRED FOR SATISFACTORY OPERATION FOR THE VARIOUS SYSTEMS.

B. INSTALL IN MOST DIRECT, NEAT AND WORKMANLIKE MANNER, EMPLOYING

ONLY MECHANICS SKILLED IN EACH TRADE. RUN EXPOSED LINES

PARALLEL WITH OR PERPENDICULAR TO BUILDING LINES. GROUP LINES

FOR EASY SERVICE.

5. OTHER MATERIAL:

A. OTHER MATERIAL, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR A

COMPLETE JOB, SHALL BE NEW AND FIRST QUALITY, FURNISHED AND

INSTALLED BY THE MECHANICAL CONTRACTOR.

6. WORKMANSHIP:

A. ALL WORK TO BE PERFORMED BY A QUALIFIED PERSONNEL NORMALLY

ENGAGED IN THE RESPECTIVE LINE OF WORK.

B. COORDINATE DEMOLITION OF SYSTEMS WITH THE GENERAL

CONTRACTOR AND OWNER.

C. THE CONTRACTOR SHALL BE RESPONSIBLE FOR MAINTAINING A NEAT

AND CLEAN WORK SITE DURING CONSTRUCTION.

D. CONTRACTOR IS RESPONSIBLE FOR COORDINATION OF OTHER TRADES

AND WORK SHALL BE ACCEPTABLE TO THE MECHANICAL ENGINEER AND

OWNER.

7. CUTTING, PATCHING, AND PAINTING:

A. ALL NECESSARY CUTTING AND PATCHING TO BE PERFORMED BY THE

GENERAL CONTRACTOR OR PRIME CONTRACTOR.

B. ALL WORK SHALL BE DONE BY QUALIFIED PERSONNEL NORMALLY

ENGAGED IN THE RESPECTIVE WORK REQUIRED AND SHALL HAVE

LICENSE AND INSURANCE FOR SUCH WORK.

C. CUTTING OF ALL OPENINGS SHALL BE COORDINATED WITH THE OWNER'S

ENGINEERING REPRESENTATIVE PRIOR TO COMMENCEMENT OF

CUTTING.

8. PRODUCT HANDLING:

A. PROTECTION: USE ALL MEANS NECESSARY TO PROTECT THE MATERIALS

OF THIS SECTION BEFORE, DURING, AND AFTER INSTALLATION AND

SHALL PROTECT THE MATERIALS AND WORK OF THE OTHER TRADES.

B. REPLACEMENTS: IN THE EVENT OF DAMAGE, IMMEDIATELY MAKE ALL

REPAIRS AND REPLACEMENTS NECESSARY TO THE APPROVAL OF THE

ENGINEER AND OWNER AT NO ADDITIONAL COST TO THE OWNER.

9. TEST AND BALANCE OF SYSTEMS:

A. AFTER COMPLETION OF THE INSTALLATION WORK, TEST AND REGULATE

ALL COMPONENTS OF THE NEW SYSTEMS AND MODIFIED SYSTEMS TO

THE SATISFACTION OF THE MECHANICAL ENGINEER AND OWNER.

B. SYSTEM SHALL BE BALANCED BY NEBB OR TABB CERTIFIED FIRM.

10. OPERATIONAL TEST AND ADJUSTMENTS:

A. CONTRACTOR SHALL BE RESPONSIBLE FOR THE ADDITIONAL ITEMS

NOTED BELOW:

B. TESTING AND START-UP OF MECHANICAL EQUIPMENT AND SYSTEMS WILL

BE REQUIRED UPON PROJECT COMPLETION. ALL PERSONNEL AND

INSTRUMENTS REQUIRED SHALL BE FURNISHED BY THE CONTRACTOR.

MECHANICAL CONTRACTORS SHALL COOPERATE WITH EACH OTHER AND

THE OWNER'S REPRESENTATIVES IN CONDUCTING TESTS.

C. ANY FINAL ADJUSTMENTS OR BALANCING FOUND NECESSARY TO BE

MADE TO THE EQUIPMENT OR SYSTEMS SO THAT THEY WILL BE PLACED

IN ACCEPTABLE OPERATING CONDITIONS AND MEET THE SPECIFIED

PERFORMANCE SHALL BE MADE DURING ANY OR ALL OF THE TESTS

SPECIFIED HEREIN.

D. ANY EQUIPMENT, SYSTEMS, OR WORK FOUND DEFICIENT DURING ANY

TESTS SHALL BE REPLACED OR REVISED AS REQUIRED, TO THE ENTIRE

SATISFACTION OF PERSONNEL.

E. BEFORE STARTING OR OPERATING ANY EQUIPMENT OF SYSTEMS, A

THOROUGH CHECK SHALL BE MADE TO DETERMINE THAT ALL SYSTEMS

HAVE BEEN FLUSHED AND CLEANED AS REQUIRED AND THAT ALL

EQUIPMENT HAS BEEN PROPERLY INSTALLED, LUBRICATED AND

SERVICED.

F. DURING TEST PERIOD, FINAL ADJUSTMENTS AND BALANCING SHALL BE

MADE TO EQUIPMENT, SYSTEMS, CONTROLS, AND CIRCUITS SO THAT ALL

ARE PLACED IN FIRST-CLASS OPERATING CONDITION.

G. UPON COMPLETION OF THE MECHANICAL WORK, OR AT SUCH A TIME

PRIOR TO COMPLETION AS MAY BE DETERMINED BY THE ENGINEER OF

RECORD, ALL MECHANICAL EQUIPMENT AND SYSTEMS SHALL BE

OPERATED AND TESTED FOR A PERIOD OF AT LEAST FIVE CONSECUTIVE

8 HOUR DAYS TO DEMONSTRATE THE SATISFACTORY OVERALL

OPERATION OF THE BUILDING OR PROJECT AS A COMPLETED UNIT.

H. CONTRACTOR SHALL PROVIDE THREE (3) PRINTED COPIES AND AN

ELECTRONIC COPY OF OPERATION AND MAINTENANCE MANUAL FOR ALL

NEW EQUIPMENT PROVIDED ON PROJECT.

MECHANICAL SPECIFICATIONS

USE

GENERAL NOTES:

COMMENTSTYPEMANUFACTURER MODELSYMBOL

GRILLES, REGISTERS, AND DIFFUSERS SHALL BE FABRICATED OF STEEL OR ALUMINUM, AS NOTED. ONLY ALUMINUM SHALL BE USED ON EXHAUST/RETURN REGISTERS OR GRILLES WHERE HEAVY CONCENTRATIONS OF MOISTURE ARE PRESENT (I.E. SHOWER ROOMS, DRYERS, ETC.) STEEL GRILLES, REGISTERS, AND DIFFUSERS SHALL BE PROVIDED WITH ZINC PHOSPHATE PRIME COAT AND BAKED WHITE ENAMEL FINISH. ALUMINUM GRILLES, REGISTERS, AND DIFFUSERS SHALL BE FINISHED WITH BAKED WHITE ENAMEL. THE TYPE OF GRILLE, REGISTER, OR DIFFUSER IS SHOWN BY SYMBOL ON THE DRAWINGS. ALL SYMBOLS SHALL BE COORDINATED BY THE CONTRACTOR WITH THE ARCHITECTURAL ROOM FINISH SCHEDULE, WHICH GOVERNS IN THE EVENT OF A CONFLICT. DISCREPANCIES WILL BE CLEARLY NOTED ON THE SUBMITTALS. FURNISH ADDITIONAL T-BAR FRAMING, AS REQUIRED TO SUPPORT CEILING MOUNTED GRILLES, REGISTERS, AND DIFFUSERS. ALL UNITS SHALL BE PROVIDED WITH CONCEALED TYPE FASTENING FRAMES. EQUIPMENT MANUFACTURED BY KRUEGER, TITUS, CARNES, PRICE, TUTTLE-BAILEY, AND ANEMOSTAT ARE ACCEPTABLE. OTHER MANUFACTURERS SHALL BE ACCEPTED BY PRIOR APPROVAL ONLY.

SUPPLY DIFFUSER LAY-INS1 ASCD 24"X24" ALUMINUM CONSTRUCTION, 3 CONE, WHITE FINISH.PRICE INDUSTRIES

SUPPLY DIFFUSER GYP BOARDS2 ASCDPRICE INDUSTRIES

REGISTER, GRILLE, DIFFUSER SCHEDULE

EXHAUST GRILLE GYP BOARDE1 80 12"X12", 1/2"GRID, ALUMINUM CONSTRUCTION, WHITE FINISH.PRICE INDUSTRIES

12"X12" ALUMINUM CONSTRUCTION, 3 CONE, WHITE FINISH.

UH-1

SYMBOL

HDS-30MODINE

MANUFAC.

505 30

CFMMODEL INPUT

115V/1PH/60HZ

VOLTAGE

24.9

OUTPUT

MBH

85 LBS

WEIGHT

UNIT COMMENTS

NATURAL GAS UNIT HEATER

FLA

3.75

MBH

NG SIZE

1/2"

RETURN GRILLE LAY-INR1 80CHPRICE INDUSTRIES

24"X12" CEILING RETURN OR TRANSFER GRILLE: ALUMINUM CONSTRUCTION, 1/2"X1/2"X1/2" (13X13X13) SQUARE EGGCRATE CORE WITH LAY-IN TYPE FRAME FOR T-BAR CEILING MOUNTING AND CONCEALED

FASTENING.

MFG'R

(O.A.E.)

MINI SPLIT EVAPORATOR (INDOOR) UNIT SCHEDULE

VOLTS/PH MCAESPMODEL CLNG HEATING

HIGH STATIC SETTINGMERV 8 FILTERS

HIGH CONDENSATE SENSOR

INSTALL PER MFGR'S DIRECTION

CFM REFRIG.

WEIGHT

BACNET INTERFACE

SOUND PRESS.TOTAL

BTUH BTUH dB(A)

CONDENSATE PUMP (if necessary) INTERFACE TO EXISTING BMS SYSTEM

SYMBOL (LBS) LEVEL

THERMOSTAT

SYMBOL MFG'R

(O.A.E.)

MINI SPLIT CONDENSING (OUTDOOR) UNIT SCHEDULE

VOLTS/PH MCA/MOCPMODEL R-410a AIRFLOW( CFM) SIZE WEIGHT

CHARGE

REFR LINE

GAS, LIQUID

MAX PIPE LENGTH

MISCELLANEOUS ITEMS

AND OPTIONS TO BE

FURNISHED BY

MECHANICAL CONTRACTOR:

SEER

SSE-1/2/3 MITSUBISHI PEAD-A09AA7 282 9000 14000R410A 1.45 58 28208-230/1.25 17.8

SSC-1/2/3 MITSUBISHI 1691SUZ-KA09NAHZ 22OZ 3/8, 1/4 208-230/1 14/24 129 LBS 65 FT

PROVIDE THERMOSTAT, DUCTED

COMBUSTION AIR AND VENT

D

C

B

A

1 2 3 4 5

1 2 3 4 5

MK DATE DESCRIPTION

A1816.33

DECEMBER 10, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

D

C

B

A

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

24568

F E S S I O NA L E NG I NE E R

12/10/2024

M-001

MECHANICAL

SCHEDULES

DH GL

A016

OFFICE

A017

OFFICE

A001

CORRIDOR

A024

COURT

CLINICIAN

A023

ADMIN.

STORAGE

UP

UP TO

GROUND

LEVEL

EXISTING

STAIRS

EXISTING

HALLWAY

OFFICE

WORK

ROOM

OFFICE

OFFICE

10"Ø

BD

8"X10"

6"Ø

10"Ø

BD

8"X10"

6"Ø

1. EXISTING HVAC UNIT TO REMAIN. MODIFY AIR DEVICES AS

REQUIRED FOR NEW LAYOUT. BALANCE EXISTING OUTSIDE

AIRFLOW TO THIS UNIT TO 40CFM. COORDINATE CEILINGS WITH

ARCHITECT BEFORE WORK BEGINS.

2. EXISTING HVAC UNT TO REMAIN. BALANCE EXISTING OUTSIDE AIR

FLOW TO THIS UNIT TO 20CFM. COORDINATE AIR DEVICES WITH

NEW CEILING LAYOUT, COORDINATE CEILING WITH ARCHITECT.

3. INSTALL NEW SPLIT SYSTEM IN NEW OFFICE AS SHOWN. ROUTE

OUTSIDE AIR TO SAME LOCATION AS EXISTING BASEMENT HVAC

UNITS. BALANCE OUTSIDE AIR AIRFLOW OF THIS UNIT TO 20cfm.

4. APPROXIMATE LOCATION OF CONDENSING UNIT LOCATED ON

ROOF. PROVIDE FACTORY FURNISHED ROOF CURB, AND

VIBRATION ISOLATION PADS. REFRIGERANT LINES SIZED PER

MANUFACTURER.

5. APPROXIMATE LOCATION OF RE-LOCATED THERMOSTAT. MOUNT

THERMOSTAT AT 48" ABOVE FINISHED FLOOR ELEVATION,

PROVIDE LOCKABLE PLASTIC COVER.

6. APPROXIMATE LOCATION OF THERMOSTAT. MOUNT THERMOSTAT

AT 48" ABOVE FINISHED FLOOR ELEVATION, PROVIDE LOCKABLE

PLASTIC COVER.

A. VERIFY EQUIPMENT CONFIGURATION REQUIREMENTS BEFORE

INSTALLATION. DUCT CONNECTIONS SHALL BE MADE AS

REQUIRED.

B. DUCT GAUGE AND HANGER SPACING SHALL BE PER SMACNA

STANDARDS.

C. MOUNT THERMOSTATS AT 60" ABOVE FINISHED FLOOR LEVEL.

D. WIRING OF SMOKE DETECTORS BY DIVISION 26.

E. ALL EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH

MANUFACTURERS RECOMMENDATIONS.

MK DATE DESCRIPTION

A1816.33

DECEMBER 09, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

01/22/2025

4' 8'2'0

SCALE: 1/4" = 1'-0"

TRUE

NORTH

PROJECT

NORTH

M-102

MECHANICAL

ENLARGED

FLOOR PLAN

BASEMENT LEVEL

DH GL

AutoCAD SHX Text

SSC-3

AutoCAD SHX Text 208/230/1

AutoCAD SHX Text

SSC-2

AutoCAD SHX Text 208/230/1

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text R1

AutoCAD SHX Text 24x24

AutoCAD SHX Text 225cfm

AutoCAD SHX Text S1

AutoCAD SHX Text 8"%%c

AutoCAD SHX Text R1

AutoCAD SHX Text 24x24

AutoCAD SHX Text 225cfm

AutoCAD SHX Text S1

AutoCAD SHX Text 8"%%c

AutoCAD SHX Text

SSE-3

AutoCAD SHX Text 282cfm

AutoCAD SHX Text

SSE-2

AutoCAD SHX Text 282cfm

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text 24568

AutoCAD SHX Text

MECHANICAL ENLARGED FLOOR PLAN - BASEMENT LEVEL

AutoCAD SHX Text A1

AutoCAD SHX Text

GENERAL INFORMATION

AutoCAD SHX Text

KEY PLAN

SYMBOL LEGEND

MECHANICAL EQUIPMENT SYMBOL

KEYED NOTE SYMBOL

G

PAD MOUNTED TRANSFORMERT

GROUND

EM

EMERGENCY EGRESS LIGHTING FIXTURE WITH BATTERY PACK,

SEE LIGHTING FIXTURE SCHEDULE, MH= 7'- 6" TO BOTTOM

THERMAL O.L. SWITCH

J

F

MOTOR CONNECTION WITH HP INDICATED. 3

A-1

HOME RUN TO PANEL, WITH BRANCH CIRCUIT NUMBERS INDICATED.

MOTOR CONNECTION, FRACTIONAL H.P (LESS THAN 1/3 HP)

SPECIAL SYSTEMS CABINET W/ HINGED DOOR AND KEYED LOCK

CEILING OR WALL BRACKET FIXTURE. SEE FIXTURE SCHEDULE.

LED OUTLET AND FIXTURE. SEE FIXTURE SCHEDULE.

SINGLE POLE WALL SWITCH, UP +48" TO TOP OF SWITCH.

KEYED SWITCH, UP +48" TO TOP OF SWITCH, SEE PLANS

THREE WAY SWITCH, UP +48" TO TOP OF SWITCH.

DIMMER SWITCH. SEE PLANS AND SPECS FOR CHARACTERISTICS

EXIT LIGHT. ARROWS INDICATE DIRECTIONAL ARROW ON FIXTURE.

JUNCTION BOX FLUSH IN WALL WITH CONNECTION TO EQUIPMENT.

J-BOX ABOVE LAY-IN CEILING W/ FLEX CONDUIT TO LAY-IN FIXTURES

BRANCH CIRCUIT IN WALLS OR CEILING WITH CONDUCTORS

INDICATED. (NEUTRAL, HOT, SWITCHED, AND GROUNDING

CONDUCTOR-LEFT TO

RIGHT RESPECTIVELY)

DUPLEX CONVENIENCE OUTLET, GROUNDING TYPE, UP +18"

UNLESS OTHERWISE INDICATED

FOURPLEX CONVENIENCE OUTLET, GROUNDING TYPE, UP +18"

UNLESS OTHERWISE INDICATED

250V-2P-4W SPECIAL PURPOSE GROUNDING OUTLET. AMPERAGE

AS INDICATED.

SURFACE MOUNTED PANEL. SEE PANEL SCHEDULE FOR

CHARACTERISTICS.

BRANCH CIRCUIT IN WALLS OR UNDER FLOOR, CONDUCTORS

INDICATED.

FLUSH MOUNTED PANEL. SEE PANEL SCHEDULE FOR

CHARACTERISTICS.

DISCONNECT SWITCH. SIZE AND POLES FOR LOAD

CONNECTED.NEMA 3R

OCCUPANCY SENSOR SWITCH UP AT STANDARD HEIGHT.OS

T

D

K

2X4 LED OUTLET AND FIXTURE. SEE FIXTURE SCHEDULE.

1X4 WALL MOUNT LED FIXTURE.

2X2 SURFACE MOUNTED LED.

EX

SINGLE OUTLET, ISOLATED GROUNDING TYPE, UP +18"

UNLESS OTHERWISE INDICATED

EMERGENCY EXIT LIGHTING FIXTURE WITH BATTERY PACK,

SEE LIGHTING FIXTURE SCHEDULE, MH= ABOVE DOOR EXIT.

A. THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR COORDINATING AND

PROVIDING ALL WORK INDICATED BY THESE DRAWINGS, INCLUDING; FURNISHING

ALL EQUIPMENT, SUPPLIES, MATERIALS AND LABOR, TO PROVIDE A COMPLETE

ELECTRICAL SYSTEM AS SHOWN/INTENDED. THE CONTRACTOR SHALL PERFORM

ALL OPERATIONS INCLUDING; CUTTING, PATCHING, CHANNELING, TRENCHING,

COMPACTION AND BACKFILLING THAT ARE NECESSARY FOR THE INSTALLATION OF

COMPLETE POWER, LIGHTING, OR OTHER ELECTRICAL SYSTEMS REPRESENTED IN

THESE DRAWINGS.

B. THE CONTRACTOR IS TO PERFORM ALL ELECTRICAL WORK IN NEAT WORKMANLIKE

MANNER IN FULL COMPLIANCE WITH ALL APPLICABLE NATIONAL, STATE, LOCAL

CODES; INCLUDING BUT NOT LIMITED TO; THE NATIONAL ELECTRICAL CODE (NEC),

ANY APPLICABLE STATE ELECTRICAL CODES, NFPA, NFPA-70E, UBC AND ADA.

FAILURE TO COMPLY WITH THESE CODES WILL BE REMEDIED AT CONTRACTOR

EXPENSE.

C. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCING WORK. NOTIFY THE

ENGINEER OF ANY DISCREPANCIES BEFORE PROCEEDING/INSTALLING. NO CLAIM

FOR ADDITIONAL MONIES/COST OR TIME EXTENSION WILL BE ALLOWED WITHOUT

PROPER NOTICE AND PRIOR DETERMINATION OF TIME AND COST TO THE

PROJECT.

D. AFTER COMPLETION OF THE INSTALLATION, THE ENTIRE SYSTEM SHALL BE

THOROUGHLY CLEANED, REMOVING ALL FOREIGN MATERIAL, PAINT, DIRT, GREASE

AND UNNEEDED LABELS OR STICKERS FROM FIXTURES, DEVICES AND EQUIPMENT.

REMOVE ALL RUBBISH AND DEBRIS THAT HAS ACCUMULATED DURING

INSTALLATION ON THE PREMISES.

E. ALL PHASES OF THE ELECTRICAL WORK SHALL BE COORDINATED WITH THE

ARCHITECT, OWNER AND THE GENERAL CONTRACTOR. WORK SHALL BE

PERFORMED TO CAUSE AS LITTLE INCONVENIENCE AS POSSIBLE TO THE OWNER.

F. THE ELECTRICAL CONTRACTOR SHALL VERIFY THE FINAL LOCATIONS OF ALL

SINKS AND PLUMBING FIXTURES WITH THE PROJECT PLUMBING CONTRACTOR

PRIOR TO ROUGH-IN. ANY ELECTRICAL DEVICES LOCATED BEHIND THE FINAL

LOCATIONS OF COUNTERS, SINKS OR OTHER PLUMBING FIXTURES, SHALL BE

SHIFTED A MINIMUM OF 8" (INCHES) TO EITHER SIDE OF THE SINK OR

OBSTRUCTION. ANY ELECTRICAL DEVICES LEFT BEHIND A COUNTER, SINK OR

OTHER PERMANENT PLUMBING FIXTURE AT THE TIME OF FINAL ELECTRICAL

WALK-THRU. SHALL BE RELOCATED AT THE ELECTRICAL CONTRACTOR'S

EXPENSE.

G. THE EXACT LOCATION OF ALL SYSTEMS AND EQUIPMENT SHALL BE FIELD

VERIFIED AND COORDINATED WITH OTHER TRADES PRIOR TO ANY INSTALLATION.

WHERE EXACT LOCATIONS ARE NECESSARY, THEY ARE DIMENSIONED ON THE

DRAWINGS. WHERE THERE IS A QUESTION OF ADEQUATE CLEARANCE OR

COORDINATION BETWEEN TRADES, THE ELECTRICAL CONTRACTOR SHALL

PREPARE "AS-BUILT" DRAWINGS APPLICABLE TO THE SITUATION FOR ENGINEERS

REVIEW.

H. SIZE ALL BOXES AND ENCLOSURES PER THE NATIONAL ELECTRICAL CODE.

WORKING SPACE FOR AND AROUND ALL ELECTRICAL EQUIPMENT AND DEVICES

SHALL BE DEFINED BY THE NATIONAL ELECTRICAL CODE.

I. THE ELECTRICAL CONTRACTOR MUST COORDINATE WITH ALL OTHER TRADES TO

INSURE THAT ALL REQUIRED COMPONENTS OF "CONTROL WORK" ARE INCLUDED

AND FULLY UNDERSTOOD IN ORDER TO PROVIDE A COMPLETE AND OPERATING

SYSTEM. NO ADDITIONAL COST SHALL BE ACCRUED BY THE OWNER AS A RESULT

OF LACK OF SUCH COORDINATION.

J. THE ELECTRICAL CONTRACTOR SHALL FAMILIARIZE HIMSELF WITH EXISTING

CONDITIONS ON THE PROJECT PRIOR TO SUBMITTING A BID, IN ORDER TO ALLOW

THE CONTRACTOR TO SUBMIT A COMPLETE BID WITHIN THE SCOPE OF THE PLANS

AND SPECIFICATIONS. THE CONTRACTOR, BY SUBMITTING A BID, IMPLIES THAT HE

HAS INVESTIGATED THE EXISTING PROJECT CONDITIONS TO HIS/HER

SATISFACTION. ANY QUESTIONS ARISING DURING THE BID PERIOD WITH REGARDS

TO THE CONTRACTOR'S FUNCTIONS, RESPONSIBILITIES, SCOPE OF WORK, OR ANY

OTHER ISSUE RELATING TO THIS PROJECT SHALL BE BROUGHT UP PRIOR TO THE

ACTUAL BID WITH THE ENGINEER FOR CLARIFICATION, NOT AFTER THE CONTRACT

HAS BEEN AWARDED.

K. ALL NEW MATERIAL INSTALLED ON THIS PROJECT IS TO BE "UL" LISTED, OR LISTED

BY ANOTHER AGENCY THAT IS RECOGNIZED BY AUTHORITY HAVING JURISDICTION.

SPECIAL OR CUSTOM BUILT DEVICES OR CONTROL PANELS ARE TO BE

ASSEMBLED USING "LISTED" COMPONENTS, AND ARE REQUIRED TO BE

RE-CERTIFIED TO PERFORM A CERTAIN TASK BY A "NATIONALLY RECOGNIZED

TESTING LAB" (NRTL).

L. ALL WIRING SHALL BE ROUTED IN CONDUIT AND SHALL BE CONCEALED IN WALLS

AND ABOVE CEILINGS UNLESS OTHERWISE INDICATED. THE CONDUIT RUNS AS

SHOWN ON THE PLANS ARE APPROXIMATE. EXACT LOCATIONS AND ROUTING

SHALL BE PER EXISTING FIELD CONDITIONS. GENERALLY, CONDUIT SHALL BE

"EMT", 1/2 " MINIMUM UNLESS NOTED OTHERWISE. WHERE REQUIRED TO PROTECT

FROM PHYSICAL DAMAGE, CONDUIT SHALL BE "GALVANIZED RIGID CONDUIT" (GRC)

OR "GALVANIZED INTERMEDIATE CONDUIT" (IMC) TYPE. USE "FLEXIBLE METALLIC

CONDUIT" ONLY WHERE INDICATED, OR IN FINAL CONNECTION POINT FOR

MECHANICAL EQUIPMENT. ALL FINAL CONNECTION TO MECHANICAL EQUIPMENT

SHALL BE MADE USING "LIQUID-TIGHT FLEXIBLE METALLIC CONDUIT" USING

STRANDED WIRE, OF WHICH THE LENGTH IS TO BE FIVE FEET (5'). SURFACE

MOUNTED RACEWAY SHALL BE USED ONLY WHERE INDICATED ON DRAWINGS AND

SHALL BE "WIREMOLD" TYPE OR EQUAL, OR AS SPECIFIED. SURFACE MOUNTED

RACEWAYS SHOULD BE MOUNTED IN CORNER OF THE WALL OR CEILING, UNLESS

OTHERWISE SHOWN. ALL EXPOSED RACEWAYS SHALL BE APPROVED BY THE

ARCHITECT PRIOR TO ROUGH-IN.

M. CONDUIT ROUGH-IN SHALL BE COORDINATED WITH THE MECHANICAL WORK TO

AVOID LOCATION CONFLICTS. PRIOR TO ROUGH-IN , CONDUIT LOCATIONS SHOULD

BE DISCUSSED WITH; THE MECHANICAL SUB-CONTRACTOR, THE CONTROLS

SUB-CONTRACTOR, AND THE MECHANICAL AND/OR ELECTRICAL ENGINEER.

INSTALL EXTERIOR WIRING IN APPROPRIATE, UTILIZING WEATHERPROOF FITTINGS,

BOXES AND COVERS. SUPPORT ALL CONDUIT FROM THE BUILDING STRUCTURE.

DO NOT SUPPORT CONDUIT FROM; VENTILATING DUCTS, MECHANICAL PIPING,

SUSPENDED CEILING GRIDS, OR THEIR HANGERS. USE ONLY ACCEPTABLE/LISTED

MEANS OF SUPPORT. EACH CONDUIT TERMINATION IS TO BE PROVIDED WITH AN

INSULATED PLASTIC BUSHING OR A CONNECTOR WITH AN INSULATED THROAT. NO

EXCEPTIONS.

N. THE CONTRACTOR SHALL REPAIR ALL DAMAGE TO WALLS,

CEILING, ETC. IN A PROFESSIONAL MANNER. ALL REPAIRS SHALL

BE MADE USING MATCHING MATERIALS AND SHALL BE

PROFESSIONALLY FINISHED TO MATCH THE EXISTING

CONDITIONS.

O. ALL EMT FITTINGS (COUPLING AND CONNECTORS) ARE TO BE

"STEEL, COMPRESSION TYPE". THE USE OF "DIE-CAST OR SET

SCREW" FITTINGS IS NOT ALLOWED. IN DAMP OR WET

LOCATIONS, EMT FITTINGS SHOULD BE "WP" WEATHERPROOF

FITTING AND MARKED.

P. THE INSTALLATION OF ALL ELECTRICAL DEVICES SHALL COMPLY

WITH THE "AMERICANS WITH DISABILITIES ACT" (ADA) AS

ADOPTED BY THE STATE OF NEW MEXICO.

Q. INSTALL ELECTRICAL EQUIPMENT AS NECESSARY OR AS

INDICATED ON THE DRAWINGS. EXTEND ALL CONDUIT AND

CONDUCTORS AND MAKE ALL FINAL CONNECTIONS MECHANICAL

AND OWNER FURNISHED EQUIPMENT AS REQUIRED. LEAVE ALL

EQUIPMENT OPERABLE CONDITION WITH APPROPRIATE

OVERLOAD AND SERVICE DISCONNECT PROTECTION AS

REQUIRED BY APPLICABLE CODES. FOLLOW THE

MANUFACTURER'S INSTALLATION GUIDELINES WHERE

APPLICABLE.

R. EXPOSED CONDUIT WILL NOT BE ACCEPTED EXCEPT IN "UTILITY

AREAS, OR WHERE SPECIFICALLY CALLED FOR ON THE

DRAWINGS.

S. IN ADDITION TO RACEWAY BONDING REQUIRED BY THE CODE AND

OUTLET BOX BONDING JUMPERS, THE CONTRACTOR SHALL

INSTALL A GREEN EQUIPMENT "GROUNDING" CONDUCTOR FOR

EACH BRANCH CIRCUIT. THE EQUIPMENT GROUNDING

CONDUCTOR SHALL BE BONDED AT ALL; JUNCTION BOXES, PULL

BOXES, DISCONNECT SWITCHES, STARTERS, VFD'S AND

MECHANICAL EQUIPMENT CABINETS, OR OTHER APPLICABLE

EQUIPMENT.

T. PROVIDE A 20 AMP, 120 VOLT "GFCI" PROTECTED RECEPTACLE

WITH A THREADED WEATHERPROOF BOX AND WEATHERPROOF

COVER, MOUNTED ON A PIECE OF PROPERLY SUPPORTED "IMC"

CONDUIT WITHIN TWENTY-FIVE FEET (25') OF EACH

ROOFTOP MECHANICAL UNIT.

U. WIRING DEVICES SHALL BE RATED FOR THE GIVEN APPLICATION

AS REQUIRED BY CODE. ALL SWITCHES AND RECEPTACLES

SHALL BE RATED A MINIMUM OF 20 AMPS, AND SHALL BE EQUAL

TO THE "HUBBELL CR AND CS" SERIES.

V. ALL CONDUCTORS SHALL BE COPPER, RATED FOR 600 VOLTS

WITH TYPE "THHN/THWN" INSULATION, UNLESS OTHERWISE

INDICATED OR SPECIFIED. MINIMUM WIRE SIZE SHALL BE #12 AWG

(SOLID OR STRANDED). WIRE SIZED #10 AWG AND LARGER IS TO

BE "STRANDED". ALL WIRING, INCLUDING LOW-VOLTAGE AND

CONTROL WIRING IS TO BE RUN IN CONDUIT, UNLESS OTHERWISE

NOTED.

W. ALL WIRES SHALL BE TAGGED AT ALL EQUIPMENT BOXES,

JUNCTION BOXES, PULL BOXES, AND CABINETS WITH APPROVED

PLASTIC TAGS BY "ACTION CRAFT", "BRADY", OR APROVED EQUAL.

X. PULL/JUNCTION BOXES ARE TO BE PROVIDED AS SHOWN OR AS

REQUIRED BY THE NEC.

Y. ALL DISCONNECT SWITCHES, STARTERS, VFD'S AND OTHER

"CONTROLLING DEVICES" SHALL BE PROVIDED WITH ENGRAVED

MICARTA NAMEPLATES INDICATING THE EQUIPMENT

CONTROLLED, THE CIRCUIT IT IS INSTALLED ON, AND THE PANEL

LOCATION IT IS FED FROM. NAMEPLATES ARE TO BE ATTACHED

WITH SCREWS, NOT ADHESIVES.

Z. INTERIOR EXHAUST FAN SWITCHES SHALL BE 20 AMP-SINGLE

POLE TOGGLE TYPE WITH A PILOT LIGHT. LABEL ALL INTERIOR

EXHAUST FAN SWITCHES WITH ENGRAVED MICARTA NAMEPLATES

READING "EXHAUST FAN". SEE THE SPECIFICATIONS TO

DETERMINE IF OTHER LABELING IS REQUIRED, WHICH SHALL TAKE

PRECEDENCE.

ELECTRICAL GENERAL NOTES

E-001

ELECTRICAL GENERAL

NOTES & SYMBOLS

FIXTURE SCHEDULE

MK DATE DESCRIPTION

A1816.33

NOVEMBER 01, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

12/09/2024

141 E. Palace Ave Garden Level Santa Fe, New Mexico 87501

Phone - 505.842.5787

B

A

FIXTURE SCHEDULE

REMARKSINSTRUCTIONS

MOUNTING

TYPE WATTS

LAMPS

LUMENSLOCATION

DESCRIPTION/CATALOG NUMBERMANUFACTURERTYPE

METALUX 4748#24EN-LD2-45-UNV

L840-CD-1 2X4 LED TROFFER RECESSEDLED

EXIT SURE-LITES ----- ----- -----EXIT LIGHT W/ DUAL

HEADS AND BATTERY

BACKUP

#APC-7-R-SQ

WALL

9224#8NLW4040C

8' LED SURFACE

WRAP

LED 76METALUX SURFACE

EM SURE-LITES ----- ----- -----

EMERGENCY LIGHT

W/ BATTERY BACKUP#CU2-LED CEILING

C 10321#8VRVT1-SL3C3

8' LED VANDAL

RESISTANT

LED 78FAIL-SAFE SURFACE

S1 SEE DETAIL

THIS SHEET

LUMARK 151.0 15,560#PRV-P-PA2-B-740-U-

T4W-SA-GM-PRVSA-BZ

LED AREA LIGHT W/ 20'

SQUARE STEEL POLE LED

AutoCAD SHX Text

LIGHT FIXTURE

AutoCAD SHX Text

GROUND LUG

AutoCAD SHX Text

BASE COVER

AutoCAD SHX Text

#2 BARE

AutoCAD SHX Text

CU GROUND

AutoCAD SHX Text

3/4 X 10' GND ROD

AutoCAD SHX Text 2'-0"

AutoCAD SHX Text 5'-0"

AutoCAD SHX Text

MINIMUM

AutoCAD SHX Text

3000 PSI CONCRETE

AutoCAD SHX Text

FOR ROUTING

AutoCAD SHX Text

UTILITY/SITE PLAN

AutoCAD SHX Text

CONDUIT FEEDER, SEE

AutoCAD SHX Text

FINISH GRADE

AutoCAD SHX Text

BUSH CONDUIT ENDS

AutoCAD SHX Text

INTEGRAL PART OF FIXTURE

AutoCAD SHX Text

PLATE FURNISHED AS

AutoCAD SHX Text

FIXTURE POLE AND BASE

AutoCAD SHX Text

CHAMFER EDGE 1" MINIMUM

AutoCAD SHX Text

CONTINUOUS AROUND BASE,

AutoCAD SHX Text

FINISH TO 6" BELOW, FINISH

AutoCAD SHX Text

GRADE SHALL BE AS DIRECTED

AutoCAD SHX Text

BY ARCHITECT

AutoCAD SHX Text

(4) GALVANIZED BOLTS

AutoCAD SHX Text

FURNISHED AS PART OF

AutoCAD SHX Text

FIXTURE, INSTALL BOLTS

AutoCAD SHX Text

PER MANUFACTURER'S

AutoCAD SHX Text

BOLT PATTERN

AutoCAD SHX Text

NO SCALE

AutoCAD SHX Text

POLE BASE DETAIL - TYPE "S1" FIXTURE

AutoCAD SHX Text 2'-6"

AutoCAD SHX Text 4#5 VERTICAL WITH 3#4 HORIZONTAL REBAR, TIES @ 12" O.C. WITH FIRST TIE @ 6" FROM BOTTOM

AutoCAD SHX Text

ACE

AutoCAD SHX Text

FJT

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

A C ENGINEERINGNGINEERING

AutoCAD SHX Text

ENTERPRISES, LLCNTERPRISES, LLC, LLC

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text W

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text D

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text O

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text X

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text O

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text C

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text F

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text K

AutoCAD SHX Text C

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text

AutoCAD SHX Text J

AutoCAD SHX Text K

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text E

T

UP TO

GROUND

LEVEL

EXISTING

STAIRS

EXISTING

HALLWAY

ED-102

ENLARGED

ELECTRICAL

DEMOLITION

FLOOR PLAN

BASEMENT LEVEL

PRE-TRIAL

SERVICES

MK DATE DESCRIPTION

A1816.33

NOVEMBER 01, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

12/09/2024

141 E. Palace Ave Garden Level Santa Fe, New Mexico 87501

Phone - 505.842.5787

AutoCAD SHX Text

ACE

AutoCAD SHX Text

ACE

AutoCAD SHX Text

ENLARGED ELECTRICAL DEMOLITION FLOOR PLAN

AutoCAD SHX Text A1

AutoCAD SHX Text 4'

AutoCAD SHX Text 8'

AutoCAD SHX Text 2'

AutoCAD SHX Text

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

KEY PLAN

AutoCAD SHX Text

BASEMENT LEVEL - PRE-TRIAL SERVICES SUITE

AutoCAD SHX Text

TRUE NORTH

AutoCAD SHX Text

PROJECT NORTH

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

A C ENGINEERINGNGINEERING

AutoCAD SHX Text

ENTERPRISES, LLCNTERPRISES, LLC, LLC

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text W

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text D

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text O

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text X

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text O

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text C

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text F

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text K

AutoCAD SHX Text C

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text

AutoCAD SHX Text J

AutoCAD SHX Text K

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text

GENERAL NOTES

AutoCAD SHX Text A. ALL ELECTRICAL DEVICES AND ASSOCIATED CONDUIT AND WIRE TO BE ALL ELECTRICAL DEVICES AND ASSOCIATED CONDUIT AND WIRE TO BE REMOVED COMPLETE UNLESS OTHERWISE NOTED. ALL EXISTING ELECTRICAL PANELS TO REMAIN UNLESS OTHERWISE NOTED.

AutoCAD SHX Text

KEYED NOTES

1. DISCONNECT AND REMOVE ALL EXISTING DEVICES IN THIS AREA, INCLUDING DISCONNECT AND REMOVE ALL EXISTING DEVICES IN THIS AREA, INCLUDING LIGHT FIXTURES, SWITCHES, RECEPTACLES, TELECOMMUNICATION DEVICES AND ASSOCIATED WIRING. VERIFY WITH EXISTING FIELD CONDITIONS AND COMPLY AS REQUIRED.

LEVEL

EXISTING

STAIRS

EXISTING

HALLWAY

A

A

AA

OS

O S

O S

AAO

S

AA

A

A

A A

EL-102

ENLARGED

LIGHTING

PLAN

BASEMENT LEVEL

PRE-TRIAL

SERVICES

MK DATE DESCRIPTION

A1816.33

NOVEMBER 01, 2024

CURRY COUNTY

SALLY PORT &

SECURE

PARKING

CLOVIS

NEW MEXICO

WWW.NCA-ARCHITECTS.COM

ARCHITECTS - PLANNERS - AIA

1306 RIO GRANDE BLVD NW

ALBUQUERQUE, NM 87104

505-255-6400 505-268-6954 FAX

12/09/2024

141 E. Palace Ave Garden Level Santa Fe, New Mexico 87501

Phone - 505.842.5787

1. CONNECT THE NEW INTERIOR LIGHTING BRANCH

CIRCUIT TO THE EXISTING LIGHTING BRANCH

CIRCUIT PREVIOUSLY REMOVED. VERIFY WITH

EXISTING FIELD CONDITIONS AND COMPLY AS

REQUIRED.

A. ALL LAY-IN GRID TROFFERS SHALL HAVE FLEXIBLE

CONDUIT CONNECTION WITH MINIMUM #12 BRANCH

CIRCUITS AND MINIMUM #12 GROUND - NO

EXCEPTIONS.

B. EMERGENCY LIGHT FIXTURES SHALL BE MOUNTED

MAXIMUM 8'-0" AFF.

C. PROVIDE DUAL LEVEL SWITCHING OF LAMPS IN

FIXTURES IN OFFICES. THE DUAL LEVEL SWITCHING

SHALL CONSIST OF SWITCHING INNER LAMP

SEPARATELY FROM OUTER LAMPS OF LIGHTS.

D. ALL DEVICE PLATES SHALL BE BRUSHED STAINLESS

STEEL TYPE. ALL DEVICES SHALL BE IVORY IN

COLOR.

E. COORDINATE THE EXACT LOCATIONS OF ALL

CEILING MOUNTED LIGHT FIXTURES WITH THE

ARCHITECTURAL REFLECTED CEILING PLANS.

F. ALL SWITCHES sHALL BE PROVIDED WITH

PERMANENT LABELING IDENTIFYING PANEL AND

BRANCH CIRCUIT CONNECTED TO.

G. ALL HOMERUNS OVER 100' TO BE MINIMUM 3/4"C

WITH MINIMUM #10 BRANCH CIRCUITS.

H. ALL EXTERIOR BUILDING MOUNTED LIGHT FIXTURES

SHALL COMPLY WITH NEW MEXICO DARK SKIES

ACT. REFER TO THE ARCHITECTURAL

ELEVATIONS FOR MOUNTING HEIGHTS AND

LOCATION PRIOR TO ROUGH-IN OF FIXTURES.

I. ALL LIGHTING BRANCH CIRCUITS SHALL BE

MINIMUM 2#12 + 1#12GR IN .5" CONDUIT, UNLESS

OTHER INDICATED.

WATTS PERMISSIBLEPERMISSABLE WATTS/SQFT AREA

LIGHTING POWER BUDGET

CHAPTER 5 - EXISTING BUILDINGS

C503.1 General

0.69 WATTS/SQ. FT. 922 636

WATTS CONNECTED

TENANT AREA

INTERNATIONAL ENERGY CONSERVATION CODE - 2021

OFFICE

NOTE: ALTERATIONS COMPLIES WITH THE REQUIREMENTS OF SECTION C503 AND ARE SUCH

THAT THE EXISTING BUILDING IS NOT LESS CONFORMING TO THE PROVISIONS OF THIS CODE

THAN THE EXISTING BUILDING WAS PRIOR TO THE ALTERATIONS.

ALTERATIONS CONFORM TO THE PROVISIONS OF THIS CODE AS THOSE PROVISIONS RELATE TO

NEW CONSTRUCTION WITHOUT REQUIRING THE UNALTERED PORTION OF THE EXISTING BUILDING

TO COMPLY WITH THIS CODE.

ALTERATIONS DO NOT CREATE AN UNSAFE CONDITION OR OVERLOAD EXISTING BUILDING

ELECTRICAL SYSTEMS.

WATTS/SF

.495

PASSES

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text #1

AutoCAD SHX Text

AutoCAD SHX Text

WORK

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text #3

AutoCAD SHX Text

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text #2

AutoCAD SHX Text

AutoCAD SHX Text

ACE

AutoCAD SHX Text

ACE

AutoCAD SHX Text

ENLARGED REFLECTED CEILING PLAN

AutoCAD SHX Text A1

AutoCAD SHX Text 4'

AutoCAD SHX Text 8'

AutoCAD SHX Text 2'

AutoCAD SHX Text

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

GENERAL INFORMATION

AutoCAD SHX Text

KEY PLAN

AutoCAD SHX Text

KEYED NOTES

AutoCAD SHX Text

BASEMENT LEVEL - PRE-TRIAL SERVICES SUITE

AutoCAD SHX Text

TRUE NORTH

AutoCAD SHX Text

PROJECT NORTH

AutoCAD SHX Text 7'-6"

AutoCAD SHX Text A.F.F.

AutoCAD SHX Text 7'-6"

AutoCAD SHX Text A.F.F.

AutoCAD SHX Text 7'-6"

AutoCAD SHX Text A.F.F.

AutoCAD SHX Text 7'-6"

AutoCAD SHX Text A.F.F.

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

A C ENGINEERINGNGINEERING

AutoCAD SHX Text

ENTERPRISES, LLCNTERPRISES, LLC, LLC

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text W

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text D

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text O

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text X

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text O

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text C

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text F

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text K

AutoCAD SHX Text C

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text T

AutoCAD SHX Text

AutoCAD SHX Text J

AutoCAD SHX Text K

AutoCAD SHX…