Draft SOW Coatings and Sealants.pdf

STATEMENT OF WORK Draft

Aircraft Coatings & Sealants

OO-ALC

Ogden Air Logistics Complex

Hill Air Force Base

TABLE OF CONTENTS

SECTION TITLE PAGE

1 SCOPE ……………………………………………………………….….……….3

2 DESCRIPTION………………………………………………………….…….…3

3 SERVICES SUMMARY………………………………………………….……..7

4 GENERAL INFORMATION………………………………………….………...8

5 COMMUNICATIONS SECURITY…………………………………….……….9

6 CONTRACTOR EMPLOYEES…………………………………………….…..10

7 HOURS OF OPERATION………………………………………………….…..10

8 ENVIRONMENTAL CONTROLS…………………………………………

9 SAFETY REQUIREMENTS……………………………………………….…...12

10 APPLICABLE DOCUMENTS…………………………………………….……13

11 QUALITY PROGRAM PLAN……………………………………………….….13

APPENDICES

A Acronyms List B Publications C Safety D Appendix D

1. Scope:

1.1 The purpose of this contract is to provide just in time delivery of aerospace coatings, sealants, and technical assistance to support the OO-ALC at Hill Air Force Base (AFB), Utah. The OO-ALC supports the 309th Aircraft Maintenance Group (309 AMXG), 309th Commodities Maintenance Group (309 CMXG), 309th Maintenance Support Group (309 MSXG), 309th Electronics Maintenance Group (309 EMXG).

1.2 The contractor shall provide all personnel, equipment, material, supervision, facilities, transportation, other items and services necessary to provide aerospace coatings, sealants and technical assistance and support.

2. Description:

2.1 Technical Requirements

2.1.1 The contractor shall provide aerospace coating(s) and sealant(s) from an authorized distributor listed in Appendix D.

2.1.2 The Aerospace coating(s) and sealant(s) products shall conform to Military Specifications as directed by Technical Orders in support of the workloads accomplished within OO-ALC at Hill AFB, Utah. The contractor shall use best commercial practices, documentation and standards, except as noted, in this Statement of Work (SOW).

2.1.2.1 Coatings

2.1.2.1.1 The aerospace coatings shall comply with the specifications for each coating in Appendix D. To ensure compliance the manufacturer and product name must be on the specification’s active qualified product list (QPL) or the manufacturer must provide a batch specific certificate of conformance (COC) to the applicable specification.

2.1.2.1.1.1 FMS 3600: FMS-3600 is an Advanced Spectrally Filled Polyurethane Topcoat, and is proprietary blended coating specification that is owned by Lockheed Martin. These coatings have special requirements on manufacturing, storage and shipping. Based on the Fort Worth Qualified Material List (FQML) for FMS-3600 Filled Advanced Spectral Topcoat, the only qualified product is FP-361 and is manufactured by CAAP Co. All vendors must be approved to purchase FP-361 by CAAP Co. before contract award.

2.1.2.1.1.2 The contractor shall notify the Government of any change in products, including change of manufacturer, and shall provide technical support and training to 309th AMXG production technicians. Request for this assistance will be made by the Government Program Manager or 309th AMXG Paint/Blast production supervisor and shall be provided within 24 hours of notification.

2.1.2.1.1.3 The contractor shall establish initial inventory within 60 calendar days after receipt of the contract, and shall subsequently deliver supplies to the Building 220 HAZMART within 24 hours of notification by the Authorized Hazardous Material (HAZMART) Operator. An increased stock level may be required based on depot schedule and customer needs. The Contractor will be given a minimum of 8 weeks’ notice prior to any stock level requirement changes.

2.1.2.1.1.4 The contractor shall store this coating in accordance with FMS-3600 security procedures and in an Original Equipment Manufacturer (OEM) approved facility. The FMS-3600 coating material shall be stored indoors from 40°F to 90°F unless otherwise specified. FMS-3600 coating material shall be used within its respective shelf life, and after the shelf life has expired, the material shall be discarded. For important storage requirements to meet export control compliance, EXPORT CONTROL COMPLIANCE REQUIREMENTS FMS-3600 coating is export controlled material that shall meet International Traffic in Arms Regulations (ITAR) requirements. Therefore, the coating shall be held in material storage under lock and key in the pharmacy at the respective United States Air Force bases. When the FMS-3600 coating is delivered to an air base, an appropriate ‘chain of custody’ shall be followed to ensure that the coating is not left unattended prior to pharmacy storage. Delivering and receiving personnel shall be present at the time of the FMS-3600 coating exchange. If this requirement cannot be met at a specific time, the coating shall stay under lock and key at its current location until the ‘chain of custody’ can be verified. REQUIREMENT CONDITION FMS-3600 coating material shall be held under lock and key at all time prior to usage. ‘Chain of custody’ Confirmation received for FMS-3600 material exchange. FMS-3600 coating shall be stored in pharmacy indoors between 40°F to 90°F. Storage shall meet all ITAR requirements.

2.1.2.1.1.5 The contractor shall notify Building 220 HAZMART POC specified on each delivery 30 minutes prior to delivery of product to allow for a Government HAZMART POC to prepare for delivery and accept the products. The products shall be properly secured during transportation and delivery in its original manufacturing packaging to 309th AMXG and accepted by a Government HAZMART POC.

2.1.2.1.1.6 The contractor shall include signed receipts with the invoices submitted on Procurement Integrated Enterprise Environment (PIEE) (Invoicing, Receipt, Acceptance, and Property Transfer) on the WAWF (Wide Area Work Flow). Accounting System may change at the Governments discretion; Government will notify Contractor of changes.

2.1.2.2 Sealants

2.1.2.2.1 The aerospace sealants furnished under this contract shall be qualified to the requirements of military and commercial specifications. Further refinement to the Military Specifications; incorporated to reflect the specific needs of Hill AFB concerning quality assurance, uniformity, consistency between batches, and requirements to meet local environmental conditions.

2.1.2.2.2 Specifications for the aerospace sealants shall comply as follows: the specifications for each sealant listed in Appendix D. To ensure compliance the manufacturer and product name must be on the specification’s active qualified product list (QPL) or the manufacturer must provide a batch specific certificate of conformance (COC) to the applicable specification.

2.1.2.3 Unique Sealant Packaging:

2.1.2.3.1 Cartridges containing Chromate shall have a red cap in color and non-Chromate shall have a green cap in color.

2.1.2.3.2 Premixed Frozen Material (PFM); shall be pre-mixed at manufacturer facility and immediately frozen to -80 degrees Fahrenheit. Contractor shall ensure this storage temperature requirement is met during all phases of delivery to end user.

2.1.2.3.3 The Contractor shall develop a color-coded inventory control system for stock rotation to ensure shelf life management to reduce waste. The Contractor shall provide the color-coded inventory control system to the Government initially and then when updated. (CDRL A001)

2.1.3 Delivery Requirements

2.1.3.1 The Government shall increase/decrease the types/quantities of aerospace coatings and aerospace sealants as listed in Appendix D quarterly due to workload requirements during the life of the contract.

2.1.3.2 The Contractor shall be responsible to deliver to Hill AFB coatings and sealants listed in Appendix D. The Contractor shall be required to provide Just in Time (as specified by delivery request) delivery to Hill AFB to preclude work stoppage, storage problems and to avoid a partial delivery to meet mission requirements unless; in the best interest of the Government and accepted by the Hazardous Material (HAZMART) Operator. The Contractor shall deliver coatings and sealants as described at the call level to Hill AFB to preclude work stoppage, storage problems and to avoid a partial delivery to meet mission requirements unless; in the best interest of the Government and accepted by the Government POC. In case of extreme events (vehicle accidents, weather, natural disaster, etc.), the contractor shall notify the delivery HAZMART Operator POC as outlined in the call as soon as possible; to provide an estimated delivery time/schedule. In the event any discrepancies in the quantity or kind of coatings and sealants arise, the contractor shall correct and deliver any inaccuracy no later than (NLT) the next business day and provide corrected invoice to the HAZMART Operator or POC. The Contractor shall provide a product Safety Data Sheet (SDS), product Technical Data Sheet (TDS), and an invoice for all deliveries. A Government HAZMART Operator at delivery location(s) shall sign all invoices.

2.1.3.3 The Manufacture date, Military or Commercial Specification shall be marked on all containers. To facilitate compliance with Department of Defense (DoD) Manual

4140.27 Vol 1, OO-ALCI23-113 paragraph 3.1.1.7, and DoDD 5134.12. The contractor shall process any returns to the manufacturer due to non-compliant material, incorrect shipments, and products delivered with less than 80% of original shelf life remaining from the date of the delivery unless waived on a case-by-case basis.

2.1.3.4 The Contractor shall provide a kit for each airframe as required. A kit comprises of the products as listed in Appendix D to complete the airframe in work. The Contractor shall also provide single line items for rework and smaller off-airframe components.

2.1.3.5 The Contractor shall deliver approved orders to locations throughout the OO- ALC. Location(s) to be determined at call level.

2.2 Technical Assistance and Support

2.2.1 The Contractor shall provide technical assistance within 24 hours after notification of a coating or sealant failure or problem.

2.2.2 The Contractor shall provide technical support and training for any approved product change(s). The Group Engineering team shall approve all product changes.

2.2.3 The Contractor shall provide weekly or as needed site visits for technical support, evaluation of materials, material processes, and inventory control.

2.2.4 The Contractor shall provide a monthly Quality Audit Site Visit Report of all technical assistance and support activities provided by the fifth business day of the month. (CDRL A002).

2.3 Additional Requirements

2.3.1 Post Award Conference. As part of this requirement, a Government provided post award conference shall be held within 10 days after award.

3. Services Summary

# Performance Objective PWS Reference

Performance Threshold

1 Color-coded inventory control system.

(CDRL A001) 2.1.2.3.1 - 2.1.2.3.3

Upon contract award and when updated.

2 Provide technical assistance of a coating or sealant failure or problem. 2.2.1

Technical assistance shall be provided within 24 hours after notification of coating/sealant failure or problem.

3 Provide technical support and training. 2.2.2

Technical support and training shall be provided with any approved product change.

Site visits for technical support, evaluation of materials and processes, and inventory control.

2.2.3

Weekly and/or as needed visits shall be provided for technical support, evaluation of materials, processes and inventory controls.

5 Quality Audit Site Visit Report (CDRL A002). 2.2.4

Reports received by the 5th business day of every month.

6 Incident/Mishap Report (CDRL A003) 4.3.4

Reported to the government

Security Manager within one (1) business day of loss.

7 Contractor Roster (CDRL A004) 6.3

No later than 10 business days after contract award.

Changes shall be provided 5 business days prior to the scheduled work

8 Quality Program Plan (CDRL A005) 11.1 – 11.5

Reviewed and approved ten (10) calendar days post contract award.

4. General Information

4.1 Security Requirements. Compliance with all security and force protection requirements is mandatory and enforced at Hill AFB.

4.2 Comply with each OO-ALC maintenance group identified in paragraph 1.1 in/out processing procedures for all contractor personnel to ensure proper security related briefing and debriefs are accomplished.

4.3 Contractor Identification Badges

4.3.1 Badge/Unescorted Entry Authorization, IAW Hill AFB Instruction 36-812.

The Government security manager shall complete an “Unescorted Entry Authorization Certificate” (AF Form 2586), for Controlled Area Line Badges requiring entry into controlled areas. Contractors granted controlled area access shall complete all necessary training and a local background check prior to requesting access, annually thereafter, until contract completion. The Contractor Representative shall complete a Form 496 for Defense Biometric Identification System (DBIDS), if required, for each employee and forward to applicable OO-ALC security officer for processing, annually thereafter until contract completion. The request shall be submitted to Security Forces Pass and Identification (building 430). The AF Form 2586 & 496 shall be returned to the Government security manager for accountability. NOTE: a valid DBIDS must be issued prior to requesting controlled area access.

4.3.1.1. Contractor employees who fail to complete annual training prior to anniversary date, and pass the written test, shall have their controlled area badge revoked and/or one shall not be issued.

4.3.1.2. If installation access is denied from a failed local file background check the contract employee/s shall be removed from the installation immediately and all credentials and access badges shall be returned to the issuing security manager the same day.

4.3.2 As required, the contractor employee shall obtain an access card from the appropriate Building Security Manager.

4.3.3 During performance of the contract and at the completion or termination of the contract, the contractor shall be responsible for prompt return of all access cards, credentials and controlled area badges within three business days to the appropriate security manager for any employee who no longer requires access to the work site, and for obtaining required identification of newly assigned personnel. Lost badges shall be reported to the Facility Security Officer (FSO) within one (1) business day of loss. The contractor shall create an Incident/Mishap report when a contract employee loses a DBIBs or Restricted/Controlled Area Badge Line badge (CDRL A003).

4.3.4 The Contractor shall follow local group procedures for reporting and safeguarding actions to include: immediately report security violation(s) to the Group Security Manager and Government PM all available facts related to each instance; and take such precautions as the Security Manager and Government PM may reasonably require for security purposes. Take reasonable and prudent action to establish control of the scene, prevent further violation, and to preserve evidence until released by proper authority;

cooperate fully and assist Government personnel as the Government conducts an investigation of the violation. Participation shall last until the investigation is completed.

4.3.5 The contractor understands that any contractor employee may be summarily and immediately removed from or denied access to any government property, facility, and installation at the sole discretion of competent government authority if that authority determines such action is necessary to protect or preserve government property, safety and security, or to maintain good order and discipline.

5. Communications Security

5.1 All communications with Department of Defense (DoD) organizations are subject to Communications Security (COMSEC) review.

5.2 The DoD authorizes the military departments to conduct COMSEC monitoring and recording of telephone calls originating from, or terminating at, DoD organizations.

5.3 The Government advises the contractor that at any time they place a call to, or receive a call from, a DoD organization, they are subject to COMSEC procedures.

5.4 The Contractor assumes the responsibility for ensuring wide and frequent dissemination of the above information to all employees dealing with official DoD information.

6. Contractor Employees

6.1 The Contractor shall not assign, to the contract or performance, any person including any employee of the U.S. Government if employing that person would create a conflict of interest under any law, regulation or policy of the United States Government.

Additionally, the Contractor shall not assign to the contract or performance, any person who is an employee of the Department of the Air Force, either military or civilian. Unless such person seeks and receives approval according to DoD Directive 5500.7-R and any other applicable regulation or policy of the Department of the Air Force or its subordinate commands.

6.2 All Contractor Management Staff or contractor personnel shall be clearly identified; at ALL times while working on Hill AFB. The Contractor identification shall include conversations, mail, email, teleconferences, video teleconferences, faxes, and/or other electronic communication whether with Government personnel, other contractor personnel, or with the public when supporting this contract where their status as contractor employees might not otherwise be apparent or where they might be mistaken for civil service employees.

Air Force issued identification badges and any contractor badges shall be worn at or above the waistline during the individual’s duty hours when not in a production or designated Foreign Object Damage (FOD) hazard area.

6.3 Contractor Roster

The Contractor shall include an updated Contractor Roster which identifies employees’ names, Government POC names, employees’ supervisor’s (or lead’s) names, date of hire, line badges, and security clearances no later than 10 business days after contract award.

Changes made to the list or status of employees shall be provided five business days prior to the scheduled work. This shall ensure the Government is aware of all contract employees on site (CDRL A004).

7. Hours of Operation

7.1 Normal hours of operation:

7.2 The Contractor shall deliver as required Monday through Friday between the hours of 0600 and 1630. The contractor shall not deliver to any drop stations between 1100 and 1200 unless otherwise specified by Contracting Officer (CO) or Program Manager (PM).

Shifts are susceptible to change during the Period of Performance (POP) due to Government worksite availability, i.e., Government furloughs, building/worksite closures. The contractor is responsible for communicating required work hours and ensuring their employees are at their designated delivery stations ready for pickup and delivery.

7.2.1 The Contractors technical personnel are authorized access to Hill AFB 24 hours a day.

7.2.2 Unless otherwise required by the Government, the contractor shall not have access to Government facilities to delivery or for technical support on the following federal holidays: New Year’s Day, Martin Luther King’s Birthday, President’s Day, Memorial Day, Juneteenth. Independence Day, Labor Day, Columbus Day, Veterans’ Day, Thanksgiving Day, and Christmas Day. If the federal holiday falls on Sunday, it is observed on Monday. If the holiday falls on Saturday, it is observed on Friday. There may also be weather related days and Government directed holidays. On these days, the Government PM shall notify the contractor and the contractor shall not be required to deliver or provide technical support; the contractor shall not bill the government for services not performed.

7.2.3 Down Days/Weather Days: The Government PM shall notify the contractor by either email or phone an official notice for Energy/Weather Down days. The contractor is not expected to provide services on Energy/Weather Down days.

7.2.4 Weekends/Holidays: Not normally expected to provide deliveries or services on weekends or holidays. Unless notified by the government shop supervisor or Engineering of a coatings or sealants failure requiring services from the contractor.

8. Environmental Controls.

8.1 Compliance with Laws and Regulations. The Contractor shall be knowledgeable of and comply with applicable Interstate, Federal, State, and Local laws, and regulations. In the event of a guidance conflict, the contractor shall follow the most stringent requirement. In the event environmental laws/regulations change during the term of this contract, the contractor is required to comply as such laws come into effect. If there is an increase or decrease in cost as a result of the change, the contractor shall inform the CO or PM pursuant to notice requirements and negotiate a modification to the contract.

8.2 The Contractor shall ensure their employees are made aware that the performance of these services shall occur in industrial areas. The OO-ALC (Ogden Air Logistics Complex) has the potential to expose workers to hazardous materials which may include, but is not limited to:

hexavalent chrome, cadmium, beryllium, lead and others. While the contractor shall not perform duties in a marked and signed regulated area [where exposures are expected to exceed the permissible exposure limits set by Occupational Safety & Health Administration (OSHA) 29 CFR 1910 Subpart Z], there may be contact hazards with these materials during cleanup of dust, metal shavings, etc. It is the contractor’s responsibility to identify such potential hazards to their contractor employees. The contractor shall ensure proper protective measures and training is taken to ensure contracted employees are protected from these hazards. Contractors should determine their own PPE requirements, after the Government informs them of the recognized hazards. Contractors shall adopt their own procedures, and shall adopt their own Contractor Hazard Assessment. The site location’s Bioenvironmental Engineering Flights have produced industrial hygiene assessments of these areas which are for information only and shall be provided at the contract level.

8.2.1 Notification of Environmental Spills. If the contractor spills or releases any substance into the environment, the contractor or its agent shall immediately report the incident to the Base Fire Department, as identified in each order. If the incident location is Hill AFB, the contractor shall contact the Hill AFB Fire Department at phone number 911. The liability for the spill or release of such substances rests solely with the contractor and its agent.

8.2.2 Material Storage and Use. The contractor shall follow manufacturer’s guidelines and professional recommendations for temperature, cleanliness, and materials handling, storage, and disposal. This may include hazardous waste/materials. The Contractor shall work with and dispose of various Hazardous Material Management IAW AFI32-7086_HILLAFBSUP, AFMAN 32-7002 chapter 3, Waste Management, AFMC and Base Supplements, and locally developed operating instructions. The Safety Data Sheet (SDS) shall be maintained on file IAW OSHA 29 CFR 1910 and shall be available to employees for review of safety and health information. The Contractor shall have a hazardous communication program developed and implemented. IAW OSHA 29 CFR 1910, to inform employees of potential hazards if and when chemicals are used, inform their employees of the labeling system, ensure their employees are trained on how to read a SDS, that the SDS is available for review, safety, and health information, and to determine the proper Personal Protective Equipment (PPE) required.

9. Safety Requirements

9.1 In performing work under this contract, the contractor shall:

9.1.1 Conform and comply with the safety requirements contained in the contract for all activities related to the accomplishment of the work. This includes the wearing of appropriate PPE. All required PPE shall be furnished by the contractor. Contractors shall conduct their own Hazard Assessment and determine what PPE they shall need.

9.1.2 Comply with all safety requirements including, but not limited to all those detailed in OSHA (Public Law 91-596), AFIs, local Operating Instructions, and process orders, Confined Space Standards, Technical Orders in relationship to safety, and Environmental Protection Agency (EPA) instructions for the protection of their employees. The contractor shall be responsible for the safety and accountability of all its employees. In the event there is conflicting guidance, the contractor shall follow the most stringent.

9.1.3 The Contractor shall always provide services in a manner, which prevents mishaps and is in compliance with all OSHA standards per AFI91-202.

9.1.4 The Contractor shall implement a safety program IAW Appendix C.

9.1.5 Ensure proper protective measures and training is taken to protect contract employees from these hazards identified in paragraph 8.2. The contractor shall instruct his/her employees to recognize potential hazards, and where necessary, inform them how to avoid the dangers associated with them. The site location Bioenvironmental Engineering Flight has produced industrial hygiene assessments of these areas in which the contractor may be working. These assessments shall be provided for contractor information only. IAW OSHA 29 CFR 1910, the contractor should be aware that the contractors are responsible for their own OSHA violations occurring in the performance of this contract. Any costs associated with issued citation are not an allowable cost under the contract or allocable to any other Government contract and production of any documentation as may be required by OSHA. The contractor shall ensure these OSHA requirements are requirements of any subcontractors.

10. Applicable Documents:

10.1 Compliance with all publications, regulations and operating instructions provided by the Government or referenced in this SOW and subsequent orders are required.

10.2 All Air Force Instruction (AFI) or AFI Supplements referenced in this SOW are attached and/or available via Air Force Epubs website https://www.e-publishing.af.mil/Product-Index/.

11. Quality Program Plan (QPP)

11.1 The Contractor shall provide a QPP. Updates shall be provided whenever there is a change in any of the following Quality System Elements: Management Responsibility Organization; Quality System Initial Quality Planning; Document Control; Process Control; Inspection & Testing; Corrective Action; Handling, Storage, Packaging, and Delivery; Quality Records; Internal Quality Audits; Training; and Quality System Effectiveness. (CDRL A005)

11.2 The Contractor shall establish and provide a complete Contractor’s QPP to ensure the requirements of this contract are provided as specified. The Contractor shall ensure quality service is maintained throughout the life of the contract. (CDRL A005)

11.3 The Contractor’s QPP shall reflect the contractor’s overall approach, internal management controls, processes, and procedures for reporting to the Government on identified aspects of quality issues. The plan shall identify the means by which the Contractor shall ensure quality effectiveness and demonstrate comprehensive management and review of data. The plan shall describe who reviews and assures that appropriate action is initiated when trends are unfavorable, who the Government shall contact for contractor quality issues. The plan shall identify how the contractor identifies and resolves deficiencies, identifies potential improvements, and maintains and makes available to the Government supporting documentation that reflects quality control inspections and corrective actions taken. The Contractor shall provide copies of all discrepancies to the Government Contracting Officer and the Government PM.

11.4 The Contractor’s QPP shall meet or exceed the minimum quality management systems elements specified in the American National Standards Institute (ANSI)/American Standards Organization (ASO)/International Standards Organization (ISO) family of standards.

11.5 The Contractors QPP shall be reviewed and approved ten (10) calendar days post contract award. (CDRL A005).

APPENDIX A

ACRONYMS

Acronym Definition AFB Air Force Base AFI Air Force Instruction ANSI American National Standards Institute AMXG Aircraft Maintenance Group ASO American Standards Organization CDRL Contract Data Requirements List CFR Code of Federal Regulations COMSEC Communications Security CMXG Commodities Maintenance Group CO Contracting Officer COC Certificate of Conformance DBIDS Defense Biometric Identification System DoD Department of Defense EMXG Electronics Maintenance Group FOD Foreign Object Damage FSO Facility Security Officer FQML Fort Worth Qualified Material List GR Government Representative HAZMART Hazardous Material Pharmacy HAZMAT Hazardous Material HAFB Hill Air Force Base IAW In Accordance With ISO International Standards Organization MXSG Maintenance Support Group NLT No Later Than OEM Original Equipment Manufacturer OO-ALC Ogden Air Logistics Complex OSHA Occupational Safety & Health Administration PFM Premixed Frozen Material PIEE Procurement Integrated Enterprise Environment POC Point of Contact PoP Period of Performance PM Program Manager PPE Personal Protective Equipment QPL Qualified Product Lists

QPP Quality Program Plan SDS Safety Data Sheets SOW Statement of Work TDS Technical Data Sheet WAWF Wide Area Work Flow

APPENDIX B

PUBLICATIONS

The Contractor shall reference and comply with most current versions of the below publications through https://www.e-publishing.af.mil/Product-Index/, https://www.esd.whs.mil/DD/, and https://www.osha.gov.

AFI 32-7086 HAFBSUP 1 HAZARDOUS MATERIAL MANAGEMENT

AFI91-202. THE US AIR FORCE MISHAP PREVENTION PROGRAM

DoDM (Department of Defense (DoD) Manual) 4140.27 Vol 1 DoD Shelf-Life Management Program: Program Administration DoDD (Department of Defense (DoD) Directive) 5134.12 Assistant Secretary of Defense for Logistics and Materiel Readiness (ASD (L&MR)) DoDD (DoD Directive) 5500.7-R Standards of Conduct “Joint Ethics Regulation” AFI32-7086_HILLAFBSUP Hazardous Material Management HILLAFBI36-812 (Hill AFB Instruction 36-812) Issue of Common Access Cards to Contractors Occupational Safety & Health Administration (OSHA) 29 CFR 1910 Subpart Z (https://www.osha.gov/laws-regs/regulations/standardnumber/1910) OO-ALCI 23-113 Shelf Life Management of Hazardous Materials (https://static.e-publishing.af.mil/production/1/oo-alc/publication/oo-alci23-113/oo-alci23- 113.docx.pdf) https://www.e-publishing.af.mil/Product-Index/ https://www.e-publishing.af.mil/Product-Index/ https://www.e-publishing.af.mil/Product-Index/ https://www.osha.gov/laws-regs/regulations/standardnumber/1910 https://static.e-publishing.af.mil/production/1/oo-alc/publication/oo-alci23-113/oo-alci23-113.docx.pdf https://static.e-publishing.af.mil/production/1/oo-alc/publication/oo-alci23-113/oo-alci23-113.docx.pdf

APPENDIX C

SAFETY, FIRE PROTECTION AND HEALTH

SPECIFICATION

INDUSTRIAL SAFETY REQUIREMENTS

OGDEN AIR LOGISTICS COMPLEX

UNITED STATES AIR FORCE

HILL AIR FORCE BASE, UTAH 84056

Aircraft Coatings & Sealants

7 April 2022

OO-ALC/SE

Control Number: KZ220401

SECTION I - GENERAL REQUIREMENTS

A. Safety Program Requirements.

The contractor will implement a safety program that ensures protection of Government personnel and property. The program will consist of, as a minimum:

1. Mishap reporting, as defined in paragraph B1 below.

2. Routine and recurring surveillance to ensure the safety requirements of this contract are enforced.

3. Identification of segregated work site locations for operations that cannot be co-mingled with general industrial operations and the process for ACO approval of operations and changes at these specific sites.

4. All contractor personnel shall be trained and qualified to perform their duties safely.

5. The contractor shall include a clause in all subcontracts requiring the subcontractors to comply with the safety provisions of this contract, as applicable.

B. Mishap Notification

1. The contractor shall notify the OO-ALC/SE workflow at OO-ALC.SE.Workflow@us.af.mil or the Hill AFB Command Post (801-777-3007) after normal duty hours, and the designated Government Representative (GR), i.e., the ACO, PCO, or DCMA COR (Contracting Officer's Representative) within one (1) hour of all mishaps or incidents at or exceeding $2,000 (material + labor) in damage to DOD property entrusted by this contract, even if the government is wholly or partially reimbursed. This notification requirement shall also include physiological mishaps/incidents. A written or email copy of the mishap/incident notification shall be sent within three calendar days to the GR, who will forward it to OO-ALC/SE. For information not available at the time of initial notification, the contractor shall provide the remaining information no later than 20 calendar days after the mishap, unless extended by the ACO.

Mishap notifications shall contain, as a minimum, the following information:

(a) Contract, Contract Number, Name and Title of Person(s) Reporting

(b) Date, Time and exact location of accident/incident

(c) Brief Narrative of accident/incident (Events leading to accident/incident)

(d) Cause of accident/incident, if known

(e) Estimated cost of accident/incident (material and labor to repair/replace)

(f) Nomenclature of equipment and personnel involved in accident/incident

(g) Corrective actions (taken or proposed)

(h) Other pertinent information

2. The contractor shall cooperate with any and all government mishap investigations.

Additionally if requested by government personnel or designated government representative (GR), i.e., the ACO, PCO, or DCMA COR (Contract Officers Representative), the contractor shall immediately secure the mishap scene/damaged property and impound pertinent maintenance and training records, until released by safety investigators.

3. The contractor shall provide copies of contractor data related to mishaps, such as contractor analyses, test reports, summaries of investigations, etc. as necessary to support the government investigation.

4. The contractor shall support and comply with the safety investigation and reporting requirements of DAFI91-204 or DAFI91-204_AFMCSUP.

C. General Safety Requirements:

The contractor is solely responsible for compliance with all federal, state and local laws, the Occupational, Safety and Health Act (OSHA) (Public Law 91-596) and the resulting standards, OSHA Standards 29 CFR 1910 and 1926, as applicable, and the protection of their employees. Additionally, the contractor is responsible for the safety and health of all subcontractor employees. All documents required as a result of OSHA 29 CFR 1910 and 1926 regulations, (i.e. certifications, training, respiratory protection program, workplace hazard assessments), shall be made available to the COR upon request.

The contractor shall ensure assigned personnel are adequately trained and qualified for the task being performed. Brief all personnel on the hazards involved with operations and applicable precautions to be taken. Should unidentified hazards arise, cease operations until actions are taken to eliminate or mitigate hazards to safe levels.

Contractor personnel must receive Explosive Safety Awareness Training if their duties require entry into the Explosive Clear Zone. This training will be provided by the OO-ALC Safety Office. Contact Tom Caygle at 586-0081.

A Risk Assessment will be required prior to any work being accomplished, if munitions will remain in the facility.

Compliance with OSHA and other applicable laws and regulations for the protection of contractor employees is exclusively the obligation of the contractor. Note: The government shall assume no liability or responsibility for the contractor's compliance or non-compliance with such requirements. The contractor shall furnish to each of his/her employees a place of employment, which is free from recognized hazards. The contractor shall brief his/her http://www.osha.gov/pls/oshaweb/owasrch.search_form?p_doc_type=STANDARDS&p_toc_level=0 employees on the safety requirements of this contract and on hazards associated with prescribed tasks. The contractor is responsible for compliance with OSHA Public Law and the resultant standards identified within. In addition, the contractor is required to flow down the safety requirements/specification to all subcontractors. This applies to Federal Acquisition Regulation (FAR) 12 commercial acquisitions as well. This contract shall in no way require persons to work in surroundings or under working conditions which are unsafe or dangerous to their health.

The contractor must coordinate and perform work so as not to impact the safety of government employees or cause damage to government property. This requires providing personnel with protective equipment and associated safety equipment as may be necessary. The contractor must also protect personnel from hazards generated by the work. If the contractor employs BILINGUAL speaking employees, they must post bilingual signs and have written procedures for specific tasks in applicable languages.

SECTION II – SPECIFIC REQUIREMENTS

PEDESTRIAN CROSSWALKS: All contractor personnel are required to use the closest crosswalk, or traffic controlled intersection when crossing the road. Pedestrians must look both ways to ensure the coast is clear before stepping out into the crosswalk.

Pedestrians DO NOT have the right of way unless they are already in the crosswalk.

Contractor vehicle operators have the same responsibilities as pedestrians, to share the road and mutually observe and yield to pedestrians.

MOTOR VEHICLES: Contractor shall comply with the standards in: DoD Directive 5525.4, Enforcement of State Traffic Laws on DoD Installations", Nov 2, 1981, Para 3-4;

DODI 6055.4, DoD Traffic Safety Program, 20 Jul 99; AFI 91-207, USAF Traffic Safety Program, 22 May 07; and AFI 91-207 AFMC SUP1, The US Air Force Traffic Safety Program, 1 Oct 07. Each applies to all persons at any time on an Air Force Installation and includes all leased, owned, or privatized property including housing areas. In addition: AFI 13-213, Airfield Management, applies to all contractors, sub-contractors, vendors, commercial delivery companies, and all other private business vehicles who operate anywhere on Hill Air Force Base, including the airfield (to include the industrial areas and any buildings or hangars located upon the airfield) in support of their mission.

HOUSEKEEPING: Housekeeping shall be conducted according to the requirements in OSHA Standard 29 CFR 1910.141. CLEAN AS YOU GO will be enforced.

Element/Requirement Referenced Benchmark

Operational Reporting (OPREP) Appendix C, Section I

AFMAN 10-206

Facility Prevention and Protection NFPA 13, 70, & 72

NFPA 409/410

DAFMAN91-203 Chapters 6, Handling, Storage and use of Flammable/ NFPA 30, 33

Hazardous Material Management AFI 32-7086

HAFBSUP 1

Flammables and Combustibles DAFMAN91-203 Chapter 22

Appendix D

Description/Noun Part Number 36473 Walkway Coating HENTZEN WALKWAY Ty II NON-CHROME Primer Hentzen 17176KEp 37038 GUNSHIP BLACK Topcoat Deft/PPG 99-BK-004 17178 SILVER TOPCOAT Deft/PPG 01-GY-93 35237 BLUE GRAY Topcoat K35603APX_G 36495 GRAY Topcoat K35601APX_G 36320 MEDIUM GRAY Topcoat K35602APX_G 36473 WALKWAY Hentzen Walkway

26492 SEMI GLOSS BLUE

GRAY PPG 9321/F26492

25237 SEMI GLOSS BLUE

GRAY PPG 9321/F25237

27038 SEMI GLOSS BLACK PPG 9321/F27038

Yellow Epoxy Primer PPG CA7233

37038 GUNSHIP BLACK 99-BK-004

Coast Guard Yellow Primer AKZO 10P20-13 New Coast Guard White AKZO ECL-T-46/TR-112FS17860 Coast Guard Blue AKZO ECL-G-2778 Coast Guard Orange AKZO ECL-G-3655 36320 Akzo Nobel Walkway AKZO ECM-F-6320 Griptex Coarse Anti-Skid AKZO AWL 73013Q 13538 YELLOW GLOSS Deft/PPG 03-Y-87 11136 RED FASTDRY Deft/PPG 03-R-064 15044 BLUE FASTDRY Deft/PPG 03-BL-139

17038 BLACK FASTDRY Deft/PPG 03-BK-071 17925 GLOSS WHITE Topcoat PPG 8201/F17925 Japanese Topcoat 15526 PPG 9311/F15526 Japanese Stencil 15107 PPG 9311/F15107 Tan Non-Chrome Primer Hentzen K16708TEP-G 36170 Gray Paint Topcoat PPG9311/F36170 36270 Teflon Coating 35631APX

GEM-POLY 36118 (2026) CAAP CO FMS-2026 (36118)

GEM-POLY 36270 (2026) CAAP CO FMS-2026 (36270)

FMS- 3049 MUDD CAAP CO 3049 MUDD

8925/I1168 Thunderbird White PPG 8925/I1168 9800/I6342 Thunderbird Blue PPG 9800/I6342 9800/I4177 Thunderbird Red PPG 9800/I4177 30140 DK BRN Hentzen 35500APX 30140

34079 HENTZEN 30479

30279 LT BRN PPG 9311/F30279

30140 DK BRN PPG 9311/F30140

36270 MED GRAY PPG 9311/F36270

36628 LT GRAY PPG 9311/36628

37038 BLACK 99BK004

35109 DK BLUE PPG 9311/F35109

35450 LT BLUE PPG 9311/F35450

30279 LT BROWN Hentzen 35500APX 30279 36375 LT GRAY Hentzen 35500APX 36375 35109 DK BLUE Hentzen 35500APX 35109 35190 MED BLUE Hentzen 35500APX 35190 36320 MED GRAY/BLUE Hentzen 35500APX 36320 13538 Semi Gloss Yellow Deft/PPG 03-Y-087 Indonesian GRAY 36314 Deft/PPG 99-GY-104 Indonesian Green 34148 Deft/PPG 99-GN-026

RAIN EROSION 16270 CAAP 6173-3

RAIN EROSION 36270 CAAP 6173-5

17925 GLOSS WHITE PPG 8203/F17925

NON CHROME FLEX PRIMER 09-Y-010

BLACK RAIN EROSION CAAP B274ASP/108

TAN NON CHROME PRIMER HENTZRN 16708TEP

Akzo 36375 Light Gray AKZO ECM-F-6375

ACCELAGOLD ALODINE Henkel Turco Accelagold BRIGHTENER, Corrosion Remover CeeBee R-66C

B&B REGEL CLEANER B&B RE-GEL

MEK/ACETONE BLEND MEK 50/50 MIX

PREKOTE PRE-KOTE

FP-361 Coatings 36170 Henkel Turco Accelagold ACCELAGOLD ALODINE

HENTZEN WALKWAY 36473 WALKWAY

CAAP B-274/AS-P108 Rain Erosion/Anti Stat AP-1 Sur-Prep AKZO 10P20-44 HS Epoxy Primer, Fluid Resistant AKZO 10P20-44MNF HS Epoxy Primer, Fluid Resistant AKZO AWL 73012G Griptex Fine Anti-Skid AKZO AWL 73013Q Griptex Coarse Anti-Skid PPG 515 X 408 SUPER KOROPON adhesion Primer

PPG 910X75104 ACCELERATOR, KOROFLEX

Deft/PPG FMS-2026 (36118) GEM-POLY 36118 (2026) Deft/PPG FMS-2026 (36270) GEM-POLY 36270 (2026)

PPG 823X439 KOROFLEX PRIMER

CAAP CO 3049 MUDD FMS- 3049 MUDD

CAAP Co. FP-500 Rain Erosion 16270 CAAP Co FP-550 Rain Erosion 36270 AERODURE 2100 MGR Akzo Non Chrome Primer CeeBee R-66C BRIGHTENER, Corrosion Remover

CAAP B274ASP/108 BLACK RAIN EROSION

Henkel/Turco 1132 Pen Alodine Pen

PPG CA7233QT YELLOW PRIMER QUARTS

Hentzen KAD9325 Green IR Regular Dry Primer Hentzen KAD9325-FD GREEN IR FAST DRY PRIMER

PPG CA7233 YELLOW PRIMER GALLONS

AKZO 10P20-14 GREEN Low IR Epoxy Primer AKZO 10P20-13 Akzo Nobel Epoxy Primer Primer Hentzen 17176KEP Ty II NON-CHROME Primer AKZO ECL-G-2778 Coast Guard Blue AKZO ECL-G-3655 Coast Guard Orange AKZO ECL-T-46/TR-112FS17860 New Coast Guard White

Deft/PPG 01-GY-93 17178 SILVER Deft/PPG 03-BK-074 37038 BLK POLY Deft/PPG 03-BK-74 37038 GUNSHIP BLACK Deft/PPG 03-GY-277 16473 GLOSS GRAY GALLONS Deft/PPG 03-R-064 11136 RED FASTDRY Deft/PPG 03-R-073 31136 RED POLY Deft/PPG 03-W-135 37925 WHITE GLOSS Deft/PPG 03-x-085 CLEAR GLOSS POLY Deft/PPG 03-Y-87 13538 YELLOW GLOSS Deft/PPG 03-Y-98 33538 YELLOW GLOSS Deft/PPG 03-BK-071 17038 BLK FASTDRY Deft/PPG 03-BL-139 15044 BLUE FASTDRY PPG 8201/F17925 17925 GLOSS WHITE Topcoat

PPG 8203/F17925 17925 GLOSS WHITE FD

PPG 8211/F30108 30108 Wyoming Brown Deft/PPG 99-BL-12 35237 BLUE GRAY Deft/PPG 99-GN-026 Indonesian Green 34148 Deft/PPG 99-GN-209 34424 GREEN Deft/PPG 99-GY-003 36375 ELT GRAY Deft/PPG 99-GY-104 Indonesian Gray 36314 Deft/PPG 99-GY-006 36320 MEDIUM GRAY Deft/PPG 99-GY-033 36495 GRAY Hentzen 35500APX 36375 36375 LIGHT GRAY PPG 9311/F15107 Japanese Stencil 15107 PPG 9311/F15526 Japanese Topcoat 15526

PPG 9311/F36173 36173 ELT GRAY

PPG 9311/F36231 36231 GRAY Paint PPG 9321/F25237 25237 SEMI GLOSS Blue GRAY

PPG 9321/F26492 26492 SEMI GLOSS BLUE GRAY

PPG 9321/F27038 27038 SEMI GLOSS BLACK

PPG 9311/F30279 Aggressor Light Brown 30279 PPG 9311/F35109 Aggressor Blue 35109 PPG 9311/F35450 Aggressor Blue 35450

PPG 9311/F36118 36118 DARK GRAY

PPG 9311/F36118 36118 GRAY POLY

PPG 9311/F36173 36173 GRAY POLY

PPG 9311/F36270 36270 MEDIUM GRAY

PPG 9800/I4177 Thunderbird Red PPG 9800/I6342 Thunderbird Blue

PPG 99-GY-031 36293 LT GRAY

AKZO ECM-F-5237 Akzo Nobel 35237 AKZO ECM-F-6320 Akzo Nobel 36320 Lt GRAY AKZO ECM-F-6375 Akzo Nobel 36375 Med GRAY AKZO ECM-F-6495 Akzo Nobel 36495 Deft/PPG 99-GY-029 16473 GLOSS GRAY QUARTS Hentzen 35500APX 30140 30140 DK BROWN Hentzen 35500APX 30219 30219 MED BROWN PPG 8201/F17925 17925 GLOSS WHITE Quart PPG 8925/I1168 Thunderbird White Dupont Axalta Imron AF400 Blue Angels Blue Blue Angel Blue Imron

Dupont Axalta Imron AF400 Blue Angels White Blue Angel White Imron

Dupont Axalta Imron AF400 Blue Angels Yellow Blue Angel Yellow Imron

DAF13081SQT Blue Angel Catalyst Hentzen 35500APX 35109 35109 DARK BLUE Hentzen 35500APX 35190 35190 MED BLUE Hentzen 35500APX 36320 36320 MED GRAY/BLUE TINT

PPG 515X386 GREEN WATERBORNE PRIMER

Deft/PPG 44GN024 Waterborne Epoxy Primer, Yellow

B&B RE-GEL B&B REGEL CLEANER

5351 TURCO PAINT STRIPPER

B&B 9095 PAINT STRIPPER- ENV Frendly (Nascar Soap) Paint Overspray Masking Fluid DEFT/ PPG 85X011 Polyurethane Accelerator Deft/PPG RECC 1015 RECC 1015 Non Chrome Pre Seal Deft/PPG RECC 3021 RECC 3021 Non Chrome Conv Coat

MEK 50/50 MIX MEK/ACETONE BLEND

10P2-3 & EC-110 10P2-3 & EC-110, ANTI-STATIC EPOXY

(GAL)

AC-130 (SURFACE

TREATMENT) AC-130 (SURFACE TREATMENT)

COR-BAN 35 Corrosion Preventitive Compound

7220-00-NTB-0041 Anti-Skid Saftey Walk PRE-KOTE PREKOTE Pre-Treatment Oakite Rustsripper Oakite Ruststripper

09-Y-010 NON CHROME FLEX PRIMER

1094-5 PREPTONE SSG (ECOLINK)

M-NT 5700 Aero Bonderite M-NT 5700 Aero

53055GEP 53055GEP Green Chromate-Free Epoxy Primer

AMS3229A 240-55 NAVSOLVE

32243APX-T2, 06480CMU 16473 GRAY URETHANE TYPE 2 class H/Hentzen

35551APX, 355503CMU-LVOC 16440 GRAY AEROZEN APC TYPE

4/Hentzen

DS108F DS-108 Wipe Solvent SW20044 Wipes/SWCN0018 Cansiter Presat Wipes DS108 (11x17)

SW2420066 Wipes/SWCN0044 Canister Presat Wipes Isopropyl Alcohol (11x17)

719287 656-58-3531 BEIGE 595B-23531 (AKZO)

870 B4 870 B12 PR-2201 B1 Sealant 20151-0275 Cee-Bee Super Bee 300 LFM 26020-0275 Cee-Bee J-3 26036-0275 Cee-Bee J-84 26025-0250 Cee-Bee J88-L 01-6000-40 Daraclean 282 Alkaline Clkeaner 756387 Liquid Bonderite M-CR T5900 Aero FluoSolv-CX Fluosolv-CX

32243APX-T2, 06480CMU-QT1 TUBEAXIAL FAN CAC90055

32243APX-T2, 06480CMU-QT2 CENTRIFICAL FAN WSS96000

PRIMER, OFF WHITE TYPE 4

70-2022-8045-2 3M Left Wheel Pod Boot Spraylat Coating White SPZ6160XXXMIB11B Spraylat Coating Black APZ6160XXXMIB11B Blue Prekote Primer Lithium Primer 2118

Primer Lithium Primer A9190 Primer Lithium Primer CS3065 PR-1440B2- 2.5OZ PMF PRC 1440 B2 PMF Fuel Cell Sealant PR-1750A-1-2-6OZ PMF PRC 1750 A1/2 PMF Fuel Cell Sealant PR-1750B1-2-6OZ PMF PRC 1750 B1/2 PMF Fuel Cell Sealant PR1750B2PMF 25 g PRC 1750 B2 PR1750B-6 PMF 6oz PRC 1750 B-6 frozen 6oz PR 1750B2-3cc PRC 1750 B2 Fuel Cell Sealant PR1750B6PMF 6 oz. PRC 1750 B6 PMF Fuel Cell sealant

PR1826B1/4 3 oz. PRC 1826 B 1/4 FAST CURE FUEL

SEALANT

PR1826B½ PRC 1826 B-½ FAST CURE FUEL

SEALANT

PR1826B2 3 oz. PRC 1826 B-2 FAST CURE FUEL

SEALANT

PR870B1/2 3oz PRC 870 B1/2 COR INHIBITING

SEALANT

PR870B½ PMF 25g PRC 870 B1/2 COR INHIBITING

SEALANT PMF

PR-870B-1-3OZ PMF PRC 870 B1/2 PMF COR INHIBITING

SEALANT

PR870B2PMF-6oz PRC 870 B2 COR INHIBITING SEALANT

PMF

PR-870B2-2OZ PMF PRC 870 B2 PMF COR INHIBITING

SEALANT

PR1432GV GAL PRC-Desoto 1432GV Sprayable Sealant PR1436S GAL PRC-Desoto 1436S Sprayable Sealant AC-350-A-2-6OZ AC 350 A2 Aerospace Sealant AC-350-A-2-3OZ PMF AC 350 A2 Aerospace Sealant PMF AC-350-B 1/2 -6OZ PMF AC 350 B1/2 Aerospace Sealant PMF AC-350-B-1-2-2OZ PMF AC 350 B 1/2 PMF Aerospace Sealant AC-350-B-2-6OZ PMF AC 350 B2 PMF Aerospace Sealant AC-350-B-2-2.5OZ PMF AC 350 B2 PMF Fuel Cell Sealant AC-350-B-4-6 OZ PMF AC 350 B4 Aerospace Sealant PMF AC-735-B-1-2-6 oz PMF AC 735 B 1/2 PMF Sealant AC-735-B-2-2 oz PMF AC 735 B2 PMF Sealant PR1425B2 6 oz. PRC 1425 B-2 canopy Sealant PR-1440A-1-2-3OZ PMF PRC 1440 A1/2 PMF Fuel Cell Sealant

PR1440B½ 3 oz. PRC 1440 B-½ Fuel Tank Sealant PR-1440B-1-2-2 OZ PMF PRC 1440 B1/2 PMF Fuel Cell Sealant PS700 8030-00-783-8898 PS700 Firewall Sealant

PR945-P/3033 3033

02Y040A-02Y040ACAT PPG DEFT Yellow Primer - TY1CLC2 AMS3276 CLA-1/2 PR1750 A1/2 - Sealant PR-1829 B-1/2 3.5 oz 1829 B1/2 - Sealant AC-160 AC 160 - Sealant 1829 B1/4 1829 B1/4 - Sealant 03W127A TYPE 1 03W127A TYPE 1 Poly TOPCOAT P10700 Handi-foam P10700 Cee-Bee R-256 CeeBee Methylene Chloride B&B 5051 B&B sealant stripper PR-1826 B-2 6oz 1829 B2 sealant FMS 3027 FMS 3027 Form 1 Epoxy Polyamide Primer COR-BAN 35 Corrosion Preventative Compound KAD 9318FD Hentzen Fast Dry Primer Tyl

N/A DARACLEAN

SAT-C3-8515 SAT WIPES

VP884002 PLASTISOL

2100P004 2100P004/TR7005 MAG RICH RED

PRIMER

504972 10P3-2 10P3-2 ZINC DUST EPOXY COATING GL

KIT

TR-49 EPOXY COATING THINNER GL

P6173-3362170KIT P6173-3-36270 KIT NSN8010-01-127-1960

P6173-5-36270KIT P6173-5-36270 KIT 8010011261427

02Y040A2OZ 02Y040A20OZ TYPE I HS CHROMATED

EPOXY

02Y040A GK 02Y040AGL TYPE 1 HS CHROMATED

EPOXY

01W081 GK 01W081GK TYPE I HS EPOXY TOPCOAT

17925

44GN98 1GK 44GN98 TYPE 1 CORRISION RESISTANT

WATER

8010P03GN204 GK 8010P03GN204GK TYPE II

POLYURETHANE

IS248 GL IS248 CLEANING SOLVENT FOR WATER

GL

IS248 5GL IS248 CLEANING SOLVENT FOR WATER

5GL

44GN098FK 44GN098GK TYPE 1 CORRISON

RESISTANT

DE02Y037XXMPG22K DEO2Y037XXMPG22K CLASS 1 TYPE 1

EPOXY

DEO97GY160XCAY22K 97GY160 AMC COATING 3:1 GL KIT

00222CHS-QPB1 00222CHS-QPB1 ZENTHANE RETARDER

QT

08618TUZ-LVOC-1 08618TUZ-LVOC POLYURETHANE CRC

SAND

7178TWU 7178TWU TYPE 2 WATER DISPERSIBLE

33446

08605GUZ-ULVOC-1 08605GUZ-ULVOC POLYURETHANE

CRC 383

AD5000ECMF33446 AD5000 SINGLE URETHANE TYPE 1

P10430KML-BP50 EXHAUST BLACK POWDER COATING

0515X410XXIKY22K 0515X410XXIKY22K PRIMER GL KIT

8000CSDXXXCAG11B 8110D3635

8110D03635CAQ32K 8110D03635CAQ32K FLAT POLY

COATING QT

8204F17925CAB52KG 8204F17925CAB52KG 17925 WHITE KIT

8GL

0825X309XXAMI01K 0825X309XXAMI01K FUEL TANK

PRIMER 2OZ

0513X408BXIKY22K 0513X408BXIKY22K

0528X310XXBMQ22K 0528X310XXBMQ22K

8202F17925MPG22K 8203F17925MPG225 GLOSS WHITE 17925

8204F17925MPG22K 8204F17925MPG22K GLOSS WHITE 17925

GL

8000D03635DMGBC3HL 8000D03635DMGBC3HL D3635 GRAY C17

7650XXXXXXCAG22K 7650XXXXXXCAG22K SANDING PRIMER

GL KIT

8203F17875MPG22K 8203F17875MPG22K TYPE I TOPCOAT

CA8203

9324F26173MPB22K 9324F26173MPB22K DESOTHANE HS SG

CA8204/F16473 GLOSS GRAY KIT 10GL

BLEND50501 ACETONE-MEK GL

04488WEP-4 DLA Hentzen Coatings Inc.

03BL149 DLA PPG…