DME26TZ05-NP001.pdf

PDF 72 KB Posted

Attached to
Cable Connector Enhancement
Solicitation number
DME26TZ05-NP001
Issued by

About this file

This is a Sources Sought notice for a Defense Manufacturing Excellence (DME) contract opportunity designated DME26TZ05-NP001 concerning Cable Connector Enhancement.

The requirement seeks development and validation of a robust, multiform factor solution to strengthen commercial off-the-shelf (COTS) cable connection points on existing fabricated printed circuit boards (PCBs). The solution must eliminate the need for custom cable manufacturing or tooling, be compatible with traditional PCB assembly and potting processes, and perform reliably under shock, vibration, and immersion testing. The objective addresses the common failure-prone interface between cables and boards due to thermal and mechanical stress. The solution must operate at temperatures between -50°C to 140°C, be compatible with MMCX, SMA, UFL, Panasonic, and Samtec connectors, work with potting materials having viscosity of 20,000 centipoise and higher, and pass specified military testing standards including MIL-STD-202 Method 201A (vibration), Method 213B Condition B (shock), and MIL-STD-810 Methods 501.5 and 503.5 (thermal).

The project is structured in three phases. Phase I requires a feasibility study of innovative enhancement approaches with target specifications and preliminary testing. Phase II involves physical testing under thermal, shock, and vibration conditions per MIL-STD standards, long-term electrical testing at three temperature conditions over 1, 2, and 4-week durations, and potting viscosity testing with materials ranging from 20,000 to 60,000 centipoise. Phase III addresses dual-use commercial applications targeting defense contractors, consumer electronics companies, and government agencies. The requirement has a projected CMMC Level 1 requirement and falls under Electronics and Materials technology areas with Microelectronics modernization priority.

View the file

Other files

File Type Posted
DMEA_STTR_26TZ_R5.pdf PDF

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

DME26TZ05-NP001: Cable Connector Enhancement

PROJECTED CMMC LEVEL REQUIREMENT:

Level 1

TECHNOLOGY AREAS:

Electronics | Materials

MODERNIZATION PRIORITIES:

Microelectronics

KEYWORDS:

PCBA, Connector, Header, environmental testing, potting

ADDITIONAL INFORMATION

N/A

OBJECTIVE:

Development and validation of a robust, multiform factor applicable solution that is able to strengthen commercial of the shelf (COTS) cable connection points on variety of existing fabricated boards to remove the burden and re design and fabrication with custom solutions for enabling more robust connections. Solution should not require custom cable manufacturing, or tooling, and be compatible with traditional printed circuit board (PCB) assembly, coating and potting processes. The solution should be evaluated against an unmodified connector, as each condition is subjected to a range of shock, vibration, and immersion testing.

DESCRIPTION:

It is widely known that the cable to board connection is a common failure prone interface for electronics systems due to the thermal and mechanical stress they are exposed to. For new designs this connection can be engineered such that risk is lowered as much as reasonably possible but for existing design, there are limited options to overcome the difficulty of maintaining a strong reliable electrical connection in stressful environments.

Potting PCBA and electronics assemblies offer great moisture, vibration and shock protection but when potting connectors the potting material is limited to the height of the connector below the electrical contact to prevent potting material from disrupting the connection between each end [3]. This ensures the board side of the connector is secure but not the full connection joint. That connection is still easily severed if it is strained beyond its mechanical limits, which for commercial grade connectors are a relatively low threshold. Commercial connectors could be swapped with more specialized connectors if they exist and the pad footprint on the board is still sufficient but removal of existing connectors from PCBAs still require considerable time for technicians.

Reworking existing boards for the purpose of swapping the connector adds additional risk of board fallout from damage or thermal cycling. Repeated use of heat guns for removing and replacing a new connector or cable solution can degrade the heat affected zone and reduce reliability of the board and neighboring components.

Especially for densely populated boards with limited distance from a connector to neighboring components which may prevent the use of a heat shield due to limited space. A heat shield can typically be used to avoid thermal and mechanical damage to adjacent components on a PCBA [4] Other options have the connector removed entirely in favor of a direct solder connection, be the board to cable or board to board. Alternative joining methods to replace the connector connection such as Hot Bar Soldering (HBS) can be cumbersome in both time and resources for small production efforts for any singular design. HBS uses pulse heated to reflow the solder material between a PCBA and the wire to form a strong junction [1]. The Hot Bar Solder (HBS) process for any given design requires tooling, fixturing and a compatible Anisotropic Conductive Film (ACF); the space between conductors, minimum pad area, the plating and substrates involved. For an existing connector footprint within a design compatible ACF may not exist and may not be able to be sourced in reasonable quantities as ACF is commonly sold by the case. While recent advancement exists for mitigating use of ACF [2] other challenges remain with design the tooling and the rework required to remove existing connectors.

The design of the tool shape is critically important to the temperature distribution across the reflow area and has significant impact on the resultant mechanical and electrical properties achieved [1]. Tooling design and fabrication iterations increase schedule requirements for assembly efforts with increasing difficulty for adequate tooling shape on densely populated boards.

These different paths or full board redesign and fabrication are expensive, time consuming and limited solutions because they are assembly specific. To enhance prototyping and system integration efforts a more versatile and efficient solution is needed to address this deficiency.

PHASE I:

Perform a feasibility study of innovative approaches to enhance the connection of COTS connectors so that it can be applied to highly stressed environmental conditions and compatible with potted and immersion applications.

The target specifications for the solution are as follows:

Capable of operating at temperatures between -50oC to 140oC• Not impact core functionality of the connector• Compatible with MMCX, SMA, UFL, Panasonic and Samtec connectors• Be compatible with potting materials having a viscosity of 20,000 cp and higher• Able to be applied to small densely populated boards• Show compatibility with existing manufacturing techniques• Be compatible with the following connector types at minimum:• Pass MIL-STD-202 Method 201A Vibration testing• Pass MIL-STD-202 Method 213B condition B Shick testing• Pass MIL-STD-810 Method 501.5, and 503.5 Thermal testing•

For a potting scenario it is assumed that the connector is fully submerged in the potting material not just potted below the contact area.

PHASE II:

Using method(s) developed in phase 1, perform physical testing of systems through the outlined environmental conditions and long-term testing of solution implemented across compatible connectors. Information to be reported for the following tests/conditions:

Thermal testing• o Pass MIL-STD-810 Method 501.5, and 503.5

Shock testing• o Pass MIL-STD-810 Method 516.6 o Pass MIL-STD-202 Method 213B condition B

Vibration testing• o Pass MIL-STD-810 Method 514.6 o Pass MIL-STD-202 Method 201A

Long term electrical testing at three different temperature conditions (-15oC, 23oC, and 45oC) for a duration of 1, 2, and 4 weeks

Potting viscosity test with potting material(s) possessing viscosities of 20,000, to 60,000 cp• Expand compatibility investigation with addition connector types•

Performer is expected to show repeatability in the data collected, provide the information and a sample of materials/tools necessary for performing the enhancement as applicable. If the performer cannot perform any of the testing outlined, justification must be provided for the exclusion of the relevant data set.

PHASE III DUAL USE APPLICATIONS:

The developed solution could be brought to market and targeted at other electronics solutions areas such as defense contractors, consumer electronics companies or the common hobbyist for commercial applications. The solution would also be directly marketable to the DOD and other government agencies who implement electronic systems into harsh or demanding environments.

REFERENCES:

Lin, Meng / Lee, Jen / Hwan, Chung / Liao, Jung Effect of Hot Bar Shape on Temperature Consistency 2008- 03 Advanced Materials Research , Vol. 33-37 p. 1319-1326

1.

Payne, Dean / Nash, Chris / Lasky, Ron Recent Advancements in Hot Bar Soldering 2023-10 SMTA International , Vol. 25 p. 579-585

2.

Molex, Potting-Capable Low-power and signal Vertical Headers 2023/10/313.

Ismail AA, Bakar MA, Ehsan AA, Jalar A, Burke J, Zolkefli ZE, Basiron E. Effect of heat shield locations on rework-induced thermal management in ball grid array solder joint. Sci Rep. 2022 Sep 6, 12(1):15118. doi:

10.1038/s41598-022-19436-6. PMID: 36068289, PMCID: PMC9448760.

4.

TECHNICAL POINT OF CONTACT (TPOC):

None

File details come from the government source that posted it. Updated .