Commercial Laundry Washing and Dryer Machines Event 1455 - AMENDED 10-20-2026.pdf
PDF 271 KB Posted
- Solicitation number
- 1455
- Issued by
- Bonner County, Idaho
About this file
This amended request for quotation (RFQ Event 1455) is issued by the Idaho Division of Veterans Services on behalf of the Idaho State Veterans Home in Pocatello (ISVH-P) for the procurement of commercial laundry equipment. The facility seeks three commercial washing machines and three commercial gas dryers to replace aging equipment currently in service. Quotes are due by 5:00 p.m. Mountain Time on October 13, 2025, with an amended deadline of October 20, 2026, and a final deadline of October 30, 2026. Delivery and installation must occur within thirty days after receipt of order (ARO) to the facility located at 1957 Alvin Ricken Drive, Pocatello, Idaho 83201. Vendors are responsible for removal of old machines to the facility dock; disposal is not required or authorized. Installation subcontracting is permitted if the awarded vendor cannot provide installation directly, though the vendor remains responsible for all subcontractor actions. The primary contact is Danny Arnold at 208-780-1326 (danny.arnold@veterans.idaho.gov), with secondary contact Sonya LaCasse at 208-780-1312.
Washing machines must meet specifications detailed in Exhibit A, including minimum capacity of 62–80 pounds, soft-mount or hard-mount configuration, 200–250 G-force extraction, variable-frequency drive motors, stainless steel construction, digital controls with minimum 20 programmable cycles, and compliance with UL, ETL, and CSA certifications. Gas dryers must meet Exhibit B specifications, including 75–100 pound capacity, natural gas firing with 132,000–175,000 BTU/hr input, automatic moisture sensing, stainless steel construction, and equivalent safety certifications. Award will be made to the responsive, responsible vendor with the lowest total cost as submitted on Exhibit C, the price sheet. The total bid must include all delivery, installation, and removal costs on a fully burdened, FOB Destination basis. Vendors must carry Commercial General Liability insurance with $1,000,000 per occurrence limits, Commercial Automobile Liability insurance with $1,000,000 per accident limits, and Workers Compensation insurance with Employer's Liability of $500,000, with certificates of insurance due within five business days of award notification. All quotes must be submitted through LUMA, and all bidders must check boxes confirming compliance with minimum specifications or risk bid rejection.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Idaho Division of Veterans Services
Event 1455 Commercial Washing Machine
AMENDED 10/20/2026
1. Purpose The Idaho Division of Veterans Service Pocatello Veterans Home (ISVH-P) further referred to as "Facility" or "Home" is requesting quotes for three (3) Commercial Washing machines and three (3) Commercial Gas Dryers further referred to as "Washers" and "Dryers" to replace the Homes aging equipment currently in place with a similar or equivalent machines, as further detailed below.
The primary lead contact for this RFQ is:
(All questions regarding this solicitation must be directed to the RFQ lead(s)
Danny Arnold, IDVS 208-780-1326 danny.arnold@veterans.idaho.gov
Secondary Lead contact for this RFQ is:
Sonya LaCasse 208-780-1312 Sonya.lacasse@veterans.idaho.gov
2. Timelines Quotes Due (by 5:00 p.m. MT) Due Date: October 13, 2025 October 20, 2026 October 30, 2026
Delivery and installation are required within thirty (30) days after receipt of order (ARO). Removal to the dock of the facility of the old machines is required upon delivery of the new Washers and Dryers. Vendor shall not remove old equipment from the site. ISVH-P reserves the right to accept delivery dates outside of the desired delivery time frame if determined to be in the best interest of the State of Idaho and Facility.
Subcontracting of Installation of all three (3) Washers and Dryers are allowed if awarded vendor cannot provide installation. Total bid amount must include installation of all three (3) Washers and Dryers. Awarded vendor shall be responsible for all actions of subcontractor.
3. Specifications See Exhibits A and B
Vendor must deliver and install three (3) Commercial Washing Machines and three (3) Commercial Gas Dryers meeting the minimum specification listed in Exhibits A and B, FOB Destination, as coordinated with the Agency contact to the address below:
Delivery Address:
Idaho State Veterans Home – Pocatello 1957 Alvin Ricken Dr.
Pocatello, ID 83201
ISHV-P Contact for delivery is:
Matt Wright 208-235-7881 mailto:danny.arnold@veterans.idaho.gov mailto:Sonya.lacasse@veterans.idaho.gov
Matt.Wright@veterans.idaho.gov
4. Award Basis
4.1 Award will be made to the responsive responsible vendor with the lowest Total Cost, as provided on Exhibit B, Price Sheet.
4.2 State of Idaho Standard Terms and Conditions will apply to this solicitation.
5. Acceptance
5.1 Upon initial inspection ISVH-P shall confirm that the Commercial Washing Machines and Commercial Gas Dryers meet the minimum specifications and requirements.
5.2 If the delivery of the Commercial Washing Machines and/or Commercial Gas Dryers do not meet the minimum requirements of the specifications, the vendor shall be required to correct the deficiency at the vendors expense within thirty (30) days.
5.3 Demonstration/training of proper operations required.
5.4 Installation of the Commercial Dishwasher required.
5.5 Removal of the old washing machines and Dryers to the outside of the facility dock location required.
Disposal of old equipment is not required or authorized and should not be included in bid.
5.6 No dealership plates or emulsions are to be placed anywhere on the new Washers and Dryers.
5.7 Direct ship from the manufacture is authorize, however bidder is still responsible for meeting all requirements and specifications of this solicitation.
6. Technical Support and information manuals
6.1 The Washers and Dryers shall be delivered with an operational manual, warranty guide, and consumer information guide necessary for proper operation and maintenance of the Washers and Dryers.
6.2 The vendor will furnish a copy of any service bulletin(s) applicable to the model of Washers and Dryers being purchased.
6.3 ISVH-P must be placed on the mailing list to receive all manufacturer/dealer service bulletins each time they are published. Bulletins must be emailed to Matt.Wright@veterans.idaho.gov
7. Response
Enter your Total Cost on Exhibit C, Price Sheet, and submit your quote via LUMA so that it is received at the Idaho Division of Veterans Service – Central Support Office (IDVS-CSO) prior to the deadline established above.
Quotes submitted by any means other than LUMA will not be accepted.
Quotes must include all Required Submittal Items (See below).
mailto:Matt.Wright@veterans.idaho.gov mailto:Matt.Wright@veterans.idaho.gov
Submitting via LUMA enter your Total Cost on Exhibit C AND in IPRO, and UPLOAD all Required Submittal Items.
List of Attachments Mandatory Required Submittal Items Exhibit A – Washer Specifications Exhibit B – Dryer Specifications Exhibit C – Price Sheet Exhibit D – IDVS Signature Page Solicitation Instructions to Vendors State of Idaho Standard Terms and Conditions
Exhibit A – Washer Specifications Exhibit B – Dryer Specifications Exhibit C – Price Sheet Exhibit D – IDVS Signature Page Warranty Information Manufacturer Drawings or specifications sheet
8. Insurance Within 5 days of notification of award (or such other time as designated by the Purchasing Activity), the apparent successful Bidder or Offeror will provide certificates of insurance required herein and will maintain the insurance during the life of the Contract. There are no provisions for exceptions to this requirement. Failure to provide the certificates of insurance within the 5-business day period may be cause for your Bid or Proposal to be declared non-responsive or for your Contract to be cancelled.
Contractor shall carry liability and property damage insurance that will protect it and the State of Idaho from claims for damages for bodily injury, including accidental death, as well as for claims for property damages, which may arise from operations under the Contract whether such operations be by themselves or by anyone directly or indirectly employed by either of them.
Contractor shall not commence work under the Contract until it obtains all insurance required under this provision and furnishes a certificate or other form showing proof of current coverage to the State. All insurance policies and certificates must be signed copies. After work commences, the Contractor will keep in force all required insurance until the Contract is terminated.
8.1. Commercial General and Umbrella Liability Insurance. Contractor shall maintain Commercial General Liability (CGL) and, if necessary, Commercial Umbrella insurance with a limit of not less than $1,000,000 each occurrence. If such CGL insurance contains a general aggregate limit, it shall apply separately to the Contract.
8.1.1. CGL insurance shall be written on ISO occurrence form CG 00 01 (or a substitute form providing equivalent coverage) and shall cover liability arising from premises, operations, independent contractors, products-completed operations, personal and advertising injury, and liability assumed under an insured contract (including the tort liability of another assumed in a business contract).
8.2. Commercial Automobile and Commercial Umbrella Liability Insurance. Contractor shall maintain Commercial
Automobile Liability and, if necessary, Commercial Umbrella Liability insurance with a limit of not less than $1,000,000 each accident. Such insurance shall cover liability arising out of any auto (including owned, hired, and non-owned autos).
8.2.1. Bidder or Offeror may request a waiver from providing Commercial Automobile and Commercial Umbrella Liability Insurance in its Bid or Proposal if the Bidder or Offeror will not use any owned, hired or non-owned vehicles to conduct business under the Contract, if it is awarded the Contract, and the State of Idaho will consider the request.
If the Bidder or Offeror submits a request to waive the provision of Commercial Automobile and Commercial Umbrella Liability Insurance after the due date and time for receipt of Bids or Proposals, the State of Idaho may not consider the request.
8.3. Workers Compensation Insurance and Employer's Liability. Contractor shall maintain workers compensation and employer's liability. The employer's liability shall have limits not less than $500,000 each accident for bodily insurance by accident or $500,000 each employee for bodily injury by disease.
8.3.1. Contractor must provide either a certificate of workers compensation insurance issued by a surety licensed to write workers compensation insurance in the State of Idaho, as evidence that the Contractor has in effect a current Idaho workers compensation insurance policy, or an extraterritorial certificate approved by the Idaho Industrial Commission from a state that has a current reciprocity agreement with the Idaho Industrial Commission.
8.4. State of Idaho as Additional Insured: The liability insurance coverage required for performance of the Contract shall include the State of Idaho, the (agency) and its divisions, officers and employees as additional insured, but only with respect to the Contractor’s activities to be performed under the Contract.
8.4.1. The Contractor must provide proof of the State of Idaho, the (agency) and its divisions, officers and employees being additional insured by providing endorsements to the liability insurance policies showing the State of Idaho, the (agency) and its divisions, officers and employees as additional insured. The endorsements must also show the policy numbers and the policy effective dates.
8.4.2. If a liability insurance policy provides for automatically endorsing additional insured when required by contract, then, in that case, the Contractor must provide proof of the State of Idaho, the (agency) and its divisions, officers and employees being additional insured by providing copies of the policy pages that clearly identify the blanket endorsement.
8.5. Notice of Cancellation or Change: Contractor shall ensure that should any of the above described policies be cancelled before the expiration date thereof, or if there is a material change, potential exhaustion of aggregate limits or intent not to renew insurance coverage(s), that written notice will be delivered to the Division of Purchasing (if the Contract was issued by the Division) or to the Purchasing Activity (contracting state agency) in accordance with the policy provisions.
8.6. Contractor shall further ensure that all policies of insurance are endorsed to read that any failure to comply with the reporting provisions of this insurance, except for the potential exhaustion of aggregate limits, shall not affect the coverage(s) provided to the State of Idaho, and its divisions, officers and employees.
8.7. Acceptable Insurers and Deductibles: Insurance coverage required under the Contract shall be obtained from insurers rated A-VII or better in the latest Bests Rating Guide and in good standing and authorized to transact business in Idaho.
The Contractor shall be financially responsible for all deductibles, self-insured retention’s and/or self-insurance included hereunder. The coverage provided by such policy will be primary to any coverage of the State on or related to the Contract and shall provide that the insurance afforded applies separately to each insured against whom a claim is made, except with respect to the limitation of liability.
8.8. Waiver of Subrogation: All policies shall contain waivers of subrogation. The Contractor waives all rights against the
State and its officers, employees, and agents for recovery of damages to the extent these damages are covered by the required policies. Policies may contain deductibles, but such deductibles will not be deducted from any damages due to the State.
Exhibit A
Specifications for Commercial Washing Machines
1. General Requirements The contractor shall furnish, deliver and install three (3) commercial-grade, washing machines meeting the minimum performance, safety, and construction requirements listed below. Equipment shall be new, unused, and of current production. Refurbished or discontinued models are not acceptable.
It is the responsibility of manufacturer to use materials, components, and design practices which are the best available, and current to industry standards for the type of operating conditions which this type of Washing Machine may be subject to. All component parts of the Washing Machine shall not merely meet the minimum requirements of this specification, but be selected to give maximum performance, service life and safety of Idaho's Veterans.
The Commercial Washing Machines must have warranty service and future maintenance onsite or with a local vendor that has the ability to pick up the Commercial Washing Machine, repair or service the Commercial Washing Machine and return to the facility.
***Bidders may offer different models, does not have to be the next in line make/model or upgraded version of what is currently in place but must meet the minimum specifications listed below***
Minor deviations of the dimensions and connections may be accepted after a review by the Maintenance Foreman for acceptance, as long as the deviations allow the Washing Machine to properly fit in the space available and all connection points. If deviations are outside the space available or connection points as deemed by the Maintenance Foreman, bid may not be considered.
All bidding vendors must check each box (☐) next to each minimum specification to indicate the offered Washer meets the minimum specification. Failure to check each box may result in your bid not being considered. Exhibit A must be included with your bid.
2. Capacity & Performance
• Washer Capacity: Minimum sixty-two (62) – eighty (80) lbs. usable capacity ☐
• Washer Type: Soft-mount or hard-mount commercial washer-extractor ☐
• G-Force Extraction: Minimum two hundred (200) – two-hundred and fifty (250) G (soft-mount preferred for high extraction) ☐
• Cycle Time: Standard mixed-load wash cycle shall not exceed thirty-five (35) – forty-five (45) minutes ☐
• Water Consumption: High-efficiency design; average < 0.5 – 1.5 gallons per lbs. of laundry ☐
• Spin Speed: Minimum one thousand (1,000) – one thousand and three hundred (1,300) RPM ☐
• Motor Type: Variable-frequency drive (VFD) motor for controlled acceleration and deceleration ☐
• Heating Options:
o Optional internal electric or steam heating ☐
3. Construction & Materials
• Drum Material: Stainless steel inner and outer drum ☐
• Frame: Welded steel frame designed for commercial duty ☐
• Cabinet: Powder-coated or stainless-steel exterior panels ☐
• Door:
o Oversized front-loading door ☐ o Door hinges must be mounted on right ☐ o Tempered glass or solid steel ☐ o Positive-latch mechanism ☐
• Suspension System:
o Soft-mount: Shock absorbers and springs ☐ o Hard-mount: Rigid frame with vibration-control design ☐
• Bearings: Heavy-duty, sealed bearings rated for continuous operation ☐
4. Controls & Interface
• Control Type: Digital commercial-grade control system ☐
• Programmability: Minimum twenty (20) programmable wash cycles ☐
• Cycle Options:
o Pre-wash ☐ o Wash ☐ o Rinse ☐ o Final rinse ☐ o High-speed extraction ☐
• Display: LED or LCD cycle status indicators ☐
• Chemical Injection: Automatic chemical injection ports (minimum 4) ☐
• Safety Interlocks: Door-lock system preventing operation when open ☐
5. Water, Electrical & Utility Requirements
• Water Connections:
o Hot and cold-water inlets ☐ o Three fourth (¾") inch or one (1") inch NPT connections ☐
• Drain Type: Pump drain or gravity drain o Must be able to drain into pit that is eleven (11") inches above the finished floor level ☐ o Drain connection between three (3") to four (4") inches ☐
• Electrical Service:
o Two hundred and eight (208v) volts, Three (3) phase, twenty (20) Amp ☐ o Dedicated circuit required ☐
• Chemical Injection: Low-voltage signal outputs for external chemical pumps ☐
6. Installation & Mounting
• Mounting Type: Hard-mount based on facility floor structure ☐
• Clearances:
o Rear: Six (6") inch minimum ☐ o Sides: Two (2") inch minimum ☐ o Front: Twenty-four (24") inch minimum service clearance ☐
• Anchoring: Hard-mount units shall include bolt-down provisions ☐
• Leveling: Adjustable leveling legs ☐
• Spacing between units: Twelve (12") inch minimum. Three (3) units plus clearance must fit in a One hundred and fifty-eight (158") inch wide space ☐
7. Safety & Compliance
• Certifications:
o Underwriters Laboratories (UL) or Electrical Testing Laboratories (ETL) listed ☐ o Canadian Standards Association (CSA) certification for gas components ☐
• Compliance:
o Must meet ANSI safety standards for commercial laundry equipment ☐ o Must comply with local/state building, plumbing, and electrical codes ☐
• Safety Features:
o Over-temperature protection ☐ o Door-lock safety system ☐ o Emergency stop function ☐
8. Efficiency & Environmental Requirements
• Energy Efficiency: High-efficiency motor and water-use design ☐
• Water-Saving Features: Automatic load-sensing water level control ☐
• Detergent Efficiency: Optimized chemical injection for reduced waste ☐
• Noise & Vibration: Must meet commercial noise-level standards ☐
9. Warranty & Support
• Parts Warranty: Minimum one (1) year ☐
• Labor Warranty: Minimum one (1) year ☐
• Drum & Motor Warranty: Minimum three 3 – five 5 years preferred ☐
• Technical Support: Manufacturer must provide U.S. based support and parts availability for ten (10) years ☐
10. Deliverables
• Operator manual ☐
• Installation manual ☐
• Maintenance schedule ☐
• Warranty documentation ☐
• Electrical, water, and drain schematics ☐
Exhibit B
Specifications for Commercial Gas Dryer
1. General Requirements The contractor shall furnish, deliver and install three (3) commercial-grade, gas-fired tumble dryer meeting the minimum performance, safety, and construction requirements listed below. Equipment shall be new, unused, and of current production. Refurbished or discontinued models are not acceptable.
It is the responsibility of manufacturer to use materials, components, and design practices which are the best available, and current to industry standards for the type of operating conditions which this type of Washing Machine may be subject to. All component parts of the Washing Machine shall not merely meet the minimum requirements of this specification, but be selected to give maximum performance, service life and safety of Idaho's Veterans.
The Commercial Washing Machines must have warranty service and future maintenance onsite or with a local vendor that has the ability to pick up the Commercial Washing Machine, repair or service the Commercial Washing Machine and return to the facility.
***Bidders may offer different models, does not have to be the next in line make/model or upgraded version of what is currently in place but must meet the minimum specifications listed below***
Minor deviations of the dimensions and connections may be accepted after a review by the Maintenance Foreman for acceptance, as long as the deviations allow the Dryer to properly fit in the space available and all connection points. If deviations are outside the space available or connection points as deemed by the Maintenance Foreman, bid may not be considered.
All bidding vendors must check each box (☐) next to each minimum specification to indicate the offered Dryer meets the minimum specification. Failure to check each box may result in your bid not being considered. Exhibit B must be included with your bid.
2. Capacity & Performance
• Dryer Capacity: seventy-five (75) to one hundred (100) pound usable capacity ☐
• Heating Type: Natural gas ☐
• BTU Input: One hundred and thirty-two thousand (132,000) – one hundred and seventy-five thousand (175,000)
BTU/hr ☐
• Drying Time: Standard mixed-load cycle shall not exceed forty (40) minutes ☐
• Airflow Rate: Minimum seven hundred and fifty (750) – one thousand and two hundred (1200) Cubic Feet per
Minute (CFM) ☐
• Temperature Range: Adjustable one hundred and thirty-five (135°) degrees Fahrenheit – one hundred and ninety
(190°) degrees Fahrenheit ☐
• Efficiency: Must include high-efficiency burner and optimized airflow system ☐
• Moisture Control: Automatic moisture sensing system preferred; timed cycles acceptable ☐
3. Construction & Materials
• Drum Material: Stainless steel, corrosion-resistant ☐
• Drum Support: Heavy-duty bearings rated for continuous commercial use ☐
• Cabinet: Fully welded steel cabinet with powder-coat finish ☐
• Door:
o Oversized loading door (minimum one hundred and eighty (180°) degree swing) ☐ o Door hinges must be mounted on right ☐ o Tempered glass or solid steel ☐ o Positive-latch mechanism ☐
• Lint System:
o Large-capacity lint drawer or basket ☐ o Easily accessible for daily cleaning ☐
• Drive System:
o Industrial-grade motor ☐ o Belt-drive or direct-drive system ☐ o Motor overload protection ☐
4. Controls & Interface
• Control Type: Digital or mechanical commercial-grade controls ☐
• Cycle Options:
o High, medium, low heat ☐ o Cool-down cycle ☐ o Auto-dry or moisture-sensing cycle ☐
• Display: LED or LCD cycle status indicators ☐
• Programmability: Minimum of three (3) preset cycles ☐
• Safety Interlocks: Door-open shutoff, over-temperature protection ☐
5. Gas & Electrical Requirements
• Gas Type: Natural gas ☐
• Gas Connection: Three fourth (3/4") inch NPT Connection, must be adjusted for altitude over four thousand
(4,000) feet ☐
• Gas Pressure: Three and one half (3.5") inch WC (natural gas) ☐
• Electrical Service:
o One hundred and twenty (120) Volt Alternating Current (AC) ☐ o Twenty (20) Amp Sixty (60) Hertz (Hz) ☐
• Ignition: Electronic spark ignition or hot-surface ignition ☐
6. Venting & Installation
• Exhaust Outlet: six (6") inch – eight (8") inch diameter ☐
• Vent Type: Rigid metal ducting only ☐
• Make-Up Air Requirement: Minimum one and a half (1.5) – two (2) square foot of free air intake ☐
• Clearances:
o Rear: six (6") inch minimum ☐ o Front: twenty-four (24") inch minimum service clearance ☐ o Three (3) units side by side must fit into a wall/frame space that is one hundred and sixteen ☐(116") inches wide and seventy-five (75") inches tall ☐
• Anchoring: Must include leveling legs or floor-mounting provisions ☐
7. Safety & Compliance
• Certifications:
o Underwriters Laboratories (UL) or Electrical Testing Laboratories (ETL) listed ☐ o Canadian Standards Association (CSA) certification for gas components ☐
• Compliance:
o Must meet American National Standards Institute (ANSI) Z21.5.1 (Gas Clothes Dryers Standard) ☐ o Must meet local/state building and fire codes ☐
• Overheat Protection: High-limit thermostat and thermal fuse ☐
• Airflow Monitoring: Automatic shutdown on airflow restriction ☐
8. Warranty & Support
• Parts Warranty: Minimum one (1) year ☐
• Labor Warranty: Minimum one (1) year ☐
• Drum & Motor Warranty: Minimum three (3) – five (5) years preferred ☐
• Technical Support: Manufacturer must provide U.S.-based support and parts availability for ten (10) years ☐
9. Deliverables
• Operator manual ☐
• Installation manual ☐
• Maintenance schedule ☐
• Warranty documentation ☐
• Gas and electrical schematics ☐
Exhibit C
Commercial Washing Machine and Gas Dryer Price Sheet
This Price Sheet must be submitted with your quote, whether the submission is manual or electronic through the Idaho eProcurement System (IPRO).
Name of Vendor: _____
Three (3) Commercial Washing Machines offered/manufacturer/model no.: _____ Three (3) Commercial Gas Dryers offered/manufacturer/model no.: ____________
Provide your TOTAL COST for Three (3) Commercial Washing Machine and Three (3) Commercial Gas Dryers, meeting the specifications outlined in Exhibits A and B. Your TOTAL COST must be fully burdened to include all costs associated with providing Three (3) Commercial Washing Machine and Three (3) Commercial Gas Dryers plus the removal of the old machines to the outside of the facility dock and no further and meeting the required minimum specifications, including delivery FOB Destination to the ISVH-P location, Idaho with installation.
TOTAL COST for Three (3) Commercial Washing Machine and Three (3) Commercial Gas Dryers:
If awarded the purchase order, will you meet the timeline for delivery specified in Paragraph 2 of this RFQ?
YES *NO
*A ‘NO’ response may disqualify you from consideration for award. If a longer delivery time is required, please provide an explanation:
Provide your approximate delivery: days ARO
Company Name:
Contact Name/Phone:
Contact E-mail:
Subcontractor Name:_____________________________________________________________
Contract Name/Phone:____________________________________________________________
Contact Email:___________________________________________________________________
| 1. Purpose |
| 2. Timelines |
| 3. Specifications |
| 4. Award Basis |
| 6. Technical Support and information manuals |
| 7. Response |
| 8.1. Commercial General and Umbrella Liability Insurance. Contractor shall maintain Commercial General Liability (CGL) and, if necessary, Commercial Umbrella insurance with a limit of not less than $1,000,000 each occurrence. If such CGL insurance con... |
| 8.1.1. CGL insurance shall be written on ISO occurrence form CG 00 01 (or a substitute form providing equivalent coverage) and shall cover liability arising from premises, operations, independent contractors, products-completed operations, personal an... |
| 8.2. Commercial Automobile and Commercial Umbrella Liability Insurance. Contractor shall maintain Commercial Automobile Liability and, if necessary, Commercial Umbrella Liability insurance with a limit of not less than $1,000,000 each accident. Such i... |
| 8.2.1. Bidder or Offeror may request a waiver from providing Commercial Automobile and Commercial Umbrella Liability Insurance in its Bid or Proposal if the Bidder or Offeror will not use any owned, hired or non-owned vehicles to conduct business unde... |
| 8.3. Workers Compensation Insurance and Employer's Liability. Contractor shall maintain workers compensation and employer's liability. The employer's liability shall have limits not less than $500,000 each accident for bodily insurance by accident or... |
| 8.3.1. Contractor must provide either a certificate of workers compensation insurance issued by a surety licensed to write workers compensation insurance in the State of Idaho, as evidence that the Contractor has in effect a current Idaho workers comp... |
| 8.4. State of Idaho as Additional Insured: The liability insurance coverage required for performance of the Contract shall include the State of Idaho, the (agency) and its divisions, officers and employees as additional insured, but only with respect ... |
| 8.4.1. The Contractor must provide proof of the State of Idaho, the (agency) and its divisions, officers and employees being additional insured by providing endorsements to the liability insurance policies showing the State of Idaho, the (agency) and ... |
| 8.4.2. If a liability insurance policy provides for automatically endorsing additional insured when required by contract, then, in that case, the Contractor must provide proof of the State of Idaho, the (agency) and its divisions, officers and employe... |
| 8.5. Notice of Cancellation or Change: Contractor shall ensure that should any of the above described policies be cancelled before the expiration date thereof, or if there is a material change, potential exhaustion of aggregate limits or intent not to... |
| 8.6. Contractor shall further ensure that all policies of insurance are endorsed to read that any failure to comply with the reporting provisions of this insurance, except for the potential exhaustion of aggregate limits, shall not affect the coverage... |
| 8.7. Acceptable Insurers and Deductibles: Insurance coverage required under the Contract shall be obtained from insurers rated A-VII or better in the latest Bests Rating Guide and in good standing and authorized to transact business in Idaho. The Cont... |
| 8.8. Waiver of Subrogation: All policies shall contain waivers of subrogation. The Contractor waives all rights against the State and its officers, employees, and agents for recovery of damages to the extent these damages are covered by the required p... |
File details come from the government source that posted it. Updated .