Clarendon CSO SC_100_Rev3.pdf

1. FIXED POSITION FIRING RANGE:

· TRAJECTORIES START AT 1' ABOVE FINISHED FLOOR AT FIRING LINE.

PAST 25 YARDS, SECONDARY TRAJECTORIES DESIGNED TO CONTAIN

6° PROJECTILE DEFLECTION.

· BAFFLE LAYOUT PROVIDES STEEL COVERAGE OF TRAJECTORY + 2"

ON BAFFLE/TRAP.

· COVERAGE EXTENDS 36" BEHIND FIRING LINE, PROVIDING A 90°

CONTAINMENT AREA AT FIRING LINE.

· BAFFLE ANGLE DESIGNED TO NOT EXCEED 30°.

· TARGETRY HEIGHT DESIGNED TO PLACE THE TOP OF HEAD AT 5'-10"

AFF.

2. TACTICAL FIRING RANGE:

· TRAJECTORIES START AT 1' ABOVE FINISHED FLOOR AT FURTHEST

FIRING POSITION TO 10 YARDS. TRAJECTORIES AT 3 YARD TO 10

YARD LOCATIONS START AT 4' ABOVE FINISHED FLOOR. SECONDARY

TRAJECTORIES DESIGNED TO CONTAIN 6° PROJECTILE DEFLECTION.

· BAFFLE LAYOUT PROVIDES STEEL COVERAGE OF 1" HORIZONTAL

OVERLAP ON BAFFLES AND 2" TRAJECTORY OVERLAP ON TRAP.

· COVERAGE EXTENDS 36" BEHIND FIRING LINE

· LAYOUT PROVIDES A 90° CONTAINMENT AREA FROM THE 3 METER

LINE TO THE FURTHEST FIRING POSITION.

· BAFFLE ANGLE DESIGNED TO NOT EXCEED 18°. TARGETRY HEIGHT

DESIGNED TO PLACE THE TOP OF HEAD AT 5'-10" AFF.

3. M.A.T.C.H. (MODULAR ARMORED TACTICAL COMBAT HOUSE):

· DESIGNED TO CONTAIN ROUNDS FIRED BETWEEN 0"AFF AND 84" AFF.

WALLS DESIGNED TO BE A NOMINAL 8' TALL, WITH 84" AFF AND

ABOVE DESIGNATED NO SHOOT ZONE.

· WALL SYSTEM AND GRID REFERENCES DESIGNED ON A 4'-0" x 4'-0"

GRID.

· PAINT SCHEME:

·· RED PAINT - NO SHOOT ZONE

·· WHITE PAINT - SHOOT ZONE

··· WHEN CONFIGURING TRAINING SCENARIO'S BE AWARE OF

THE TRAJECTORY OF THE ROUND AFTER IT PENETRATES

THE INTENDED TARGET.

·· TAN PAINT - CAUTION ZONE

··· ROUNDS HAVE POTENTIAL TO PENETRATE THIS ZONE.

4. BUILDING / EQUIPMENT ACCESS:

· SCREW CONVEYOR SYSTEM / DUST COLLECTION SYSTEM:

·· SUGGESTED ACCESS AREA AROUND EQUIPMENT FOR THE

DISPOSE OF COLLECTED MATERIALS IS:

··· 4'-6" - FOR A FORKLIFT

··· 3'-0" - FOR A PALLET JACK

· SPACE NEEDED FOR MATERIALS INSTALLATION AND INSTALLATION

EQUIPMENT:

·· SUGGESTED ACCESS AREA TO RANGE AREA: (FOR ENTIRE

DURATION OF INSTALLATION)

··· MIN (1) 4'-6" WIDE BY 7'-6" TALL ACCESS PER RANGE/BAY

5. CONCRETE SPECS:

· ALL CONCRETE MUST HAVE A FLATNESS TOLERANCE OF 1/8" OVER

20' (3MM OVER 6M) FOR ANY CONCRETE WORK WHERE ACTION

TARGET EQUIPMENT WILL BE INSTALLED AND/OR ATTACHED (WALLS

AND FLOOR). CONCRETE SURFACES MUST NOT BE CROWNED OR

SLOPED UNLESS SPECIFICALLY NOTED ON ACTION TARGET

DRAWINGS.

· RANGE FLOOR CONCRETE SHOULD BE 3,000 PSI MINIMUM, IDEALLY

5,000 PSI. IF CMU BLOCKS ARE USED FOR RANGE SIDE WALLS, THEY

SHOULD BE HIGH DENSITY BLOCKS OF AT LEAST 4,000 PSI, CAVITIES

MUST BE FILLED WITH 4,000 PSI CONCRETE. MORTAR LINES SHOULD

BE "FLUSH" WITH THE BLOCK INSIDE RANGE AND NOT "INDENTED".

CLARENDON CSO, SC

DESIGN CRITERIA: DISCLAIMERS:

NOTICE TO BUILDER & ALL SUBCONTRACTORS

THESE DOCUMENTS PROVIDE INFORMATION ONLY ABOUT ACTION TARGET'S

PRODUCTS AND NOTHING MORE. IT IS THE INTENT OF ACTION TARGET THAT

THESE DOCUMENTS BE ACCURATE, PROVIDING LICENSED PROFESSIONALS

CLEAR INFORMATION. EVERY ATTEMPT HAS BEEN MADE TO PREVENT

ERROR. THE CUSTOMER, OWNER, BUILDER, AND ALL SUBCONTRACTORS

ARE REQUIRED TO REVIEW ALL THE INFORMATION CONTAINED IN THESE

DOCUMENTS PRIOR TO THE COMMENCEMENT OF ANY WORK. ACTION

TARGET IS NOT RESPONSIBLE FOR ANY ERRORS, OMISSIONS, OR

MISINTERPRETATIONS UNDETECTED AND NOT REPORTED TO ACTION

TARGET PRIOR TO CONSTRUCTION. ALL CONSTRUCTION MUST BE IN

ACCORDANCE WITH THE INFORMATION FOUND IN THESE DOCUMENTS. ANY

QUESTIONS REGARDING THE INFORMATION FOUND IN THESE DOCUMENTS

SHOULD BE DIRECTED TO OUR OFFICE AT (801) 377-8033 IMMEDIATELY. NO

BACKCHARGES WILL BE CONSIDERED FOR REIMBURSEMENT BY ACTION

TARGET WITHOUT ADVANCED NOTIFICATION AND APPROVAL BY ACTION

TARGET. PAYMENTS WILL BE MADE IN ACCORDANCE WITH THE TERMS OF

THE AGREEMENT

· ELECTRICAL:

WHERE ELECTRICAL CONTRACTOR IS REQUIRED ALL ACTION TARGET

INC. ELECTRICAL DRAWINGS WILL BE USED ONLY AS REFERENCE

MATERIAL FOR THE ELECTRICAL CONTRACTOR TO UTILIZE IN THEIR

DESIGN OF THE COMPLETE BUILDING / RANGE SYSTEM (UNLESS

NOTED OTHERWISE.) FINAL LOCATION OF ELECTRICAL EQUIPMENT

CONTAINED IN THE ACTION TARGET INC. ELECTRICAL LAYOUTS TO BE

VERIFIED WITH ACTION TARGET INC., ELECTRICAL CONTRACTOR,

AND CUSTOMER BEFORE INSTALLATION.

· ARCHITECTURAL:

ALL BUILDING MEASUREMENTS ARE TO BE CONSIDERED ACTION

TARGET INC. SUGGESTIONS, UNLESS PROPER DIMENSIONAL PLANS /

INFORMATION HAS BEEN PROVIDED. ACTION TARGET INC. IS NOT

LIABLE FOR ANY CONFLICTS BETWEEN ITS EQUIPMENT AND ANY

VARIATIONS FROM THE BUILDING DESIGN (AS PORTRAYED FROM

CUSTOMER TO ACTION TARGET INC. EITHER BY PROVIDED PLANS OR

OTHER FORM OF COMMUNICATION) AND THE COMPLETED BUILDINGS

DIMENSIONS AND LAYOUT. ADDITIONAL MATERIAL AND PRODUCT

REDESIGN MAY BE REQUIRED IF THE STRUCTURE VARIES FROM

INDICATED SIZE AND LAYOUT.

· STRUCTURAL:

WHERE ENGINEER IS REQUIRED ALL ITEMS PERTAINING TO ACTION

TARGET INC. MATERIALS AND EQUIPMENT, AND IT'S CONNECTION TO

/ SUPPORT FROM THE STRUCTURE IS TO BE VERIFY AND APPROVED

BY THE ENGINEER OF RECORD. ALL ACTION TARGET INC. PLANS

INDICATING ANCHOR SIZES AND CONNECTION METHOD, CONCRETE

DEPTH, REBAR LAYOUTS, AND ANY OTHER ITEMS PERTAINING TO

THE CONNECTION AND SUPPORT OF ACTION TARGET INC.

EQUIPMENT TO BE UTILIZED BY ENGINEER AS ACTION TARGET INC.'S

PREFERRED METHOD.

· USE AND REPRODUCTION:

THE USE OF THESE PLANS SHALL BE RESTRICTED TO THE ORIGINAL

PROJECT SITE FOR WHICH THEY WERE PREPARED. PUBLICATIONS

EXPRESSLY LIMITED TO SUCH USE, RE-USE, REPRODUCTION, OR

PUBLICATION BY ANY METHOD IN WHOLE OR PART IS PROHIBITED,

UNLESS WRITTEN CONSENT IS PROVIDED BY ACTION TARGET INC.

DRAWINGS REMAIN THE PROPERTY OF ACTION TARGET INC.

WITHOUT RESERVATION.

· SHEETS Z5XX.X

STANDARD DETAIL SHOWN FOR REFERENCE ONLY ACTUAL

INSTALLATION MAY VARY.

SHEET INDEX:GENERAL ELECTRICAL NEEDS:

1. RANGE WILL HAVE 120/240 VAC AND MULTIPLE 20 AMP CIRCUITS

PROVIDED BY OTHERS IF ANY OF THE FOLLOWING CONDITIONS ARE

PRESENT IN ATTACHED RANGE DESIGN:

· TARGETRY IS PRESENT.

· TARGETRY CONTROL EQUIPMENT IS PRESENT.

· STALL (AND/OR) RANGE LIGHTING IS PRESENT.

· COMMUNICATION SYSTEMS ARE PRESENT.

· A DUST COLLECTION UNIT IS PRESENT.

· AN AIR COMPRESSOR IS PRESENT

2. RANGE WILL HAVE MULTIPLE 3 PHASE 208/240/480 VAC DISCONNECTS

PROVIDED BY OTHERS IF ANY OF THE FOLLOWING CONDITIONS ARE

PRESENT IN ATTACHED RANGE DESIGN:

· A SCREW CONVEYOR SYSTEM IS PRESENT. (TYPICALLY UTILIZES 2

OR MORE 3HP 3 PHASE MOTORS)

· A DUST COLLECTION UNIT IS PRESENT.

3. CUSTOMER TO PROVIDE ACCESS TO INTERNET FOR ACTION TARGET

EQUIPMENT.

4. - THE DENOTES HOME RUN OF CAT5e OR GREATER FROM DATA

JACK LOCATION TO GENESIS RANGE SERVER PATCH PANEL.

5. - THE (XX) DENOTES PORT ID# AND CORRESPONDING PATCH PANEL

WIRING LOCATION.

ABBREVIATED UN-ABBREVIATED

~ APPROXIMATE / APPROXIMATELY

AFF ABOVE FINISHED FLOOR

APROX APPROXIMATE / APPROXIMATELY

ATI ACTION TARGET INC.

AWG AMERICAN WIRE GAUGE

BOS BOTTOM OF STEEL

BOT BOTTOM

CL CENTER LINE

CFM CUBIC FEET PER MINUTE

DCU DUST COLLECTION UNIT

EMT ELECTRICAL METALLIC TUBING

EQ EQUAL / EQUALS

EQ APROX EQUAL APPROXIMATE

HVAC HEATING, VENTILATION, AND AIR CONDITIONING

LBS POUNDS

MDU MOTOR DRIVE UNIT

NTS NOT TO SCALE

PSI POUNDS PER SQUARE INCH

RBT RUBBER BERM TRAP

SCS SCREW CONVEYOR SYSTEM

SPKR SPEAKER

TCT TOTAL CONTAINMENT TRAP

TCT 2 TOTAL CONTAINMENT TRAP VERSION 2

TCT 4 TOTAL CONTAINMENT TRAP VERSION 4

TCT 4D TOTAL CONTAINMENT TRAP VERSION 4D

TYP TYPICAL

UNO UNLESS NOTED OTHERWISE

UON UNLESS OTHERWISE NOTED

GSR GENESIS SERVER RACK

SRAS SMART RANGE AXIS SCREEN

# FLOOR PLAN

Scale - 1/4" = 1'-0"#

SYMBOLS & CALLOUTS

DETAIL NUMBER

DETAIL PAGE

AREA /

ITEM DETAILED

PAGE NUMBER

DETAIL NAME

DETAIL SCALE

DETAIL NUMBER

PAGE NUMBER

END OF DETAIL

SECTION AREA DETAIL NUMBER

PAGE NUMBER

FULL SECTION CUT LINE

20'-0" [6.10]

STANDARD METRIC (METERS)

DETAIL NUMBER

Z101 RANGE PLAN

· ALL DIMENSION LINES SHOW DEFAULT OF U.S. STANDARD UNITS, WITH

METRIC UNITS AS SECONDARY INDICATED BY THERE LOCATION

BETWEEN THE FOLLOWING SYMBOLS [ ]

SEE EXAMPLE BELOW FOR CLARIFICATION:

ABBREVIATIONS:

DIMENSIONS CLARIFICATION:

XX

XX

Z301 RANGE SECTION

Z001 INDEX PAGE

Z535.5 POWER 90 DETAILS

Z700 GENERAL ELECTRICAL NOTES

Z701 ELECTRICAL RANGE PLAN

Z704.1 TARGET CONTROL MODULE DETAILS

Z745.5 POWER 90 ELECTRICAL SCHEMATIC

Z757.1 COMPRESSOR ROOM DETAILS

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z001

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

INDEX

PAGE

Signature:

Printed Name:

Date:

CUSTOMER APPROVAL:

NOTWITHSTANDING THE CONTRACT DOCUMENTS, APPROVAL OF THESE DRAWINGS SHALL ACT AS AN AMENDMENT

TO THE PARTIES' AGREEMENT AND SUPERSEDE ALL PREVIOUS DRAWINGS.

75'-0"

[25 YD]

9'-0"

[3 YD]

'-8

7' -0

7'

-0

7' -0

7'

-0

7' -0

7'

-0

7' -0

7'

-0

~5 '-4

FIRING

LINE

TARGET

LINE

3 YD

FIRING

LINE

CL

LANE LINES SHOWN FOR CLARITY ONLY

-BY OTHERS

POWER 90

SEE Z535.5

~5 '-4

Z101

1 RANGE PLAN

Scale - 3/16" = 1'-0"

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z101

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

RANGE

PLAN

75'-0"

[25 YD]

9'-0"

[3 YD]

FIRING

LINE

TARGET

LINE

3 YD

FIRING

LINE

1'-3"

0'-1 3/4"

1'-0"

1'-4 3/4"

0' -6

LE

G

TARGET

LINE

3 YD

FIRING

LINE

5' -0

TRAJECTORY LINE

POWER 90

SEE Z535.5

2' -6

VE

R

IF

Y H

EI

G

H T

O F

EX

IS

TI

N

G

KN

EE

W

AL

L

Z301

Z301

2 Target Line Section Scale - 1/2" = 1'-0"

Z301

1 Range Section Scale - 3/16" = 1'-0"

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z301

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

RANGE

SECTION

NOTE:

SPACE BELOW STRUCTURAL MEMBER SHALL

BE FREE OF OBSTRUCTIONS UNLESS

COORDINATED WITH ACTION TARGET.

WOOD HOLDER

FOR TARGET

TARGET

POWER 90

HOLDER

HOLDER

WING BOLT

POWER 90 LEG

ACTUATOR ASSEMBLY

0' -8

0' -1

0"

1'-3 3/4"

1'-4 1/2"

BASE LENGTH

POWER 90 MOTOR

LEG BASE TO CONCRETE FLOOR

1'-1 3/4"

Ø0'-0 1/2"

TYP.

TARGET LINE

POWER 90

TARGET LINE

CONCRETE WEDGE ANCHORS

1/2" FLEX W/ TIE DOWN STRAP

3" WIRE RACEWAY

1'-4 3/4"

BALLISTIC KNEE-WALL REQUIRED

TO PROTECT POWER 90

-BY OTHERS

CONCRETE PAD

-BY OTHERS

2' -6

M

IN

0'-3"

MIN.

0' -6

LE

G

2'-1 1/2"

STANDARD TARGET HOLDER

Z535.5

1 Power 90 Target Details Scale - 1 - 1/2" = 1'-0"

Z535.5

Z535.5

2 Power 90 Top View Scale - 6" = 1'-0"

Z535.5

3 Power 90 ELEVATION VIEW Scale - 1 - 1/2" = 1'-0"

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z535.5

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

POWER 90 DETAILS

1. INSTALLATION OF ALL WORK SHALL BE IN ACCORDANCE WITH THE FOLLOWING

REGULATIONS, CODES, ETC.

A. LOCAL CODES AND ORDINANCES

B. THE EDITION OF THE NATIONAL ELECTRICAL CODE NFPA 70 (NEC) IN EFFECT.

2. PRIOR TO BEGINNING ANY WORK, SECURE NECESSARY PERMITS OR CLEARANCES FROM

THE AUTHORITIES HAVING JURISDICTION. PROVIDE ALL LABOR AND MATERIALS FOR A

COMPLETE INSTALLATION. WORK SHALL BE EXECUTED BY EXPERIENCED ELECTRICIANS

WHO ARE LICENSED IN THE JURISDICTION WHERE THE PROJECT IS LOCATED.

3. THE CONTINUITY OF ALL EXISTING CIRCUITS TO REMAIN SHALL BE MAINTAINED.

4. THE ELECTRICAL PLANS ARE DIAGRAMMATIC ONLY. COORDINATE ELECTRICAL

EQUIPMENT LOCATION AND INSTALLATION WITH EQUIPMENT BEING SERVED. PROVIDE

ALL POWER AND TELECOMMUNICATION FINAL CONNECTIONS TO THE SYSTEM

FURNITURE AS REQUIRED.

5. ALL EQUIPMENT SUCH AS RELAYS, SWITCHES, PANELS, AND OTHER APPURTENANCES

SHALL HAVE IDENTIFICATION PLATES OF BLACK LAMINATED PLASTIC WITH 1/2" WHITE

LETTERS. ALL JUNCTION BOXES IN CEILING CAN BE MARKED WITH BLACK PERMANENT

MARKER ON COVER PLATES AS PANEL DESIGNATION AND CIRCUIT NUMBER FROM WHICH

THEY ARE FED.

6. ALL CONDUCTORS SHALL BE IDENTIFIED. ALL WIRING DEVICES SHALL BE USED WITH

TYPED LABEL ON THE COVER PLATE IDENTIFYING THE PANEL DESIGNATION AND CIRCUIT

NUMBER FROM WHICH THEY ARE FED.

7. ALL EQUIPMENT SHALL BE "UL" LISTED.

8. ELECTRICAL SYSTEMS SHALL BE GROUNDED PER ARTICLE 250 OF THE NATIONAL

ELECTRICAL CODE.

9. ALL CONNECTIONS TO DEVICES SHALL BE TAPED WITH SCOTCH 33 ELECTRICAL TAPE.

10. ALL CONDUITS AND JUNCTION BOXES SHALL BE CONCEALED IN FINISHED AREAS. PRIOR

TO CONCEALMENT OF NEW CONSTRUCTION, ALL WORK BEHIND FINISHED SURFACES

SHALL BE INSPECTED BY THE OWNER'S REPRESENTATIVE.

11. CONTRACTOR SHALL INFORM THE OWNER'S REPRESENTATIVE PRIOR TO BEGINNING

CONSTRUCTION AND PRIOR TO COMPLETION OF CONSTRUCTION TO ALLOW SUFFICIENT

TIME FOR COORDINATION OF EXISTING BUILDING ACTIVITIES WITH THE CONSTRUCTION

WORK.

12. CONTROL WIRING SHALL BE TAGGED AT EACH END AND TERMINATED WHERE WORK HAS

BEEN PERFORMED IN ACCORDANCE WITH EQUIPMENT MANUFACTURES SPECIFICATIONS.

13. IF MATERIAL OR EQUIPMENT IS INSTALLED BEFORE IT IS APPROVED, THE CONTRACTOR

SHALL BE LIABLE FOR ITS REMOVAL AND REPLACEMENT AT NO ADDITIONAL CHARGE OR

IF IN THE OPINION OF ACTION TARGET, THE MATERIAL OR EQUIPMENT

DOES NOT MEET THE INTENT OF THE DRAWINGS AND SPECIFICATIONS.

14. THE CONTRACTOR SHALL INCLUDE IN THE WORK, WITHOUT EXTRA COST, ANY LABOR,

MATERIALS, SERVICES, APPARATUS, AND DRAWINGS IN ADDITION TO CONTRACT

DOCUMENTS, IN ORDER TO COMPLY WITH ALL APPLICABLE LAWS, INDICATED AND/OR

SPECIFIED. PROVIDE ALL ELECTRICAL EQUIPMENT WITH ALL NECESSARY ASSOCIATED

ACCESSORIES AND CONDUIT INFRASTRUCTURE AS REQUIRED TO ENSURE A COMPLETE

AND OPERATIONAL SYSTEM AT NO ADDITIONAL COST TO OWNER.

15. BEFORE SUBMITTING BIDS, THE CONTRACTOR SHALL VISIT THE SITE AND EXAMINE ALL

ADJOINING EXISTING BUILDINGS, EQUIPMENT, AND SPACE CONDITIONS ON WHICH HIS

WORK IS IN ANY WAY DEPENDANT FOR THE BEST WORKMANSHIP AND OPERATION

ACCORDING TO THE INTENT OF THE SPECIFICATIONS AND DRAWINGS. HE SHALL REPORT

TO ACTION TARGET ANY CONDITION WHICH MIGHT PREVENT HIM FROM

INSTALLING HIS COMPONENTS IN THE MANNER SPECIFIED OR AS SHOWN IN CONTRACT

DOCUMENTS TEN BUSINESS DAYS PRIOR TO SUBMISSION OF BIDS. NO CONSIDERATION

OR ALLOWANCE WILL BE GRANTED FOR FAILURE TO VISIT THE SITE, NOR FOR ANY

ALLEGED MISUNDERSTANDING OF MATERIALS TO BE FURNISHED OR WORK TO BE

PERFORMED. THE CONTRACTOR SHALL INCLUDE IN HIS BID PRICE ALL LABOR AND

MATERIAL THAT MAY EFFECT HIS WORK.

16. THE CONTRACTOR SHALL NOTIFY ACTION TARGET IN WRITING OF ANY

DISCOVERED CONFLICTS BETWEEN EXISTING INSTALLATIONS WHICH ARE NOT

SCHEDULED FOR DEMOLITION AND THE NEW WORK INDICATED WITHIN THE CONTRACT

DOCUMENTS. SUCH NOTIFICATION SHALL BE ACCOMPANIED BY A DRAWING DELINEATING

THE PROPOSED SOLUTION PRIOR TO STARTING ANY WORK IN THE AFFECTED AREA.

17. ALL MATERIALS AND WORK SHALL BE ACCORDING TO BASE BUILDING SPECIFICATIONS

UNLESS OTHERWISE NOTED.

18. REFER TO ARCHITECTURAL DRAWINGS FOR THE EXACT LOCATION, ELEVATION,

MOUNTING HEIGHTS AND DETAILS OF ALL LIGHT FIXTURES AND DEVICES. REPORT ANY

DISCREPANCIES TO ACTION TARGET IMMEDIATELY.

19. VERIFY DOOR SWINGS BEFORE INSTALLING SENSORS AND LIGHT SWITCHES.

20. PROVIDE PLASTER RING WITH PULL STRING TO SPACE ABOVE SUSPENDED CEILING FOR

ALL TELEPHONE, DATA, FAX, MODEM, CATV, CARD READER, ETC. OUTLETS INSTALLED IN

HOLLOW PARTITIONS. PROVIDE 3/4" EMPTY CONDUIT AND PULL STRING TO SPACE ABOVE

SUSPENDED CEILING FOR THESE OUTLETS INSTALLED IN AN INSULATED PARTITION.

PROVIDE 1" E.C. WITH 2 STRINGS FOR COMBINATION DATA/TEL OUTLET.

21. MAINTAIN INTEGRITY OF THE FIRE RATED CONSTRUCTION WHERE CONDUITS PASS

THROUGH WALLS AND FLOORS.

22. ALL BACK BOXES INSTALLED ON OPPOSITE SIDES OF THE SAME PARTITION SHALL BE

STAGGERED. DO NOT MOUNT THE BACK BOXES BACK TO BACK.

23. TYPE MC CABLE MAY BE USED IN LIEU OF EMT FOR BRANCH CIRCUITS, IN DRYWALL

PARTITION AND IN CEILING PLENUM WHERE IS ALLOWED BY NEC AND THE BUILDING

OWNER. (MC CABLE FOR ISOLATED CIRCUIT SHALL HAVE TWO (2) SEPARATE GROUNDING

CONDUCTORS).

24. CONTRACTOR'S SCOPE OF WORK INCLUDES TRACING ALL EXISTING CIRCUITS IN THE

CONSTRUCTION AREA BACK TO SOURCE. IF REMOVAL OF EXISTING ELECTRICAL

EQUIPMENT AFFECTS ANY EXISTING CIRCUITS, CONTRACTOR SHALL PROVIDE CIRCUIT

BREAKERS, WIRING, CONDUIT, ETC. REQUIRED TO RECONNECT EXISTING-TO-REMAIN

25.ELECTRICAL CONTRACTOR TO COORDINATE WITH MECHANICAL, PLUMBING, AND OTHER

TRADES TO PROVIDE ALL EQUIPMENT ASSOCIATED WITH THEIR RESPECTIVE TRADES WITH

NECESSARY WIRING AND CONDUIT INFRASTRUCTURE FOR ALL SENSORS, AND CONTROL

SYSTEMS AS REQUIRED.

ELECTRICAL GENERAL NOTES ELECTRICAL SYMBOL LIST:

-GENERAL ELECTRICAL NOTES FOR INDOOR AND OUTDOOR RANGES:

J JUNCTION BOX (AS SIZED IN SCHEDULE)

S

3 WAY SWITCH

SWITCH

WEATHER PROOF REC.

GROUND FAULT REC.

\ SWITCHED REC.

DUPLEX REC.

L15-30 RECEPTACLE

P PULL BOX (AS SIZED IN SCHEDULE)

S

START AND STOP SWITCH

5E CAT5E JACK & WALL PLATE

ELECTRICAL ABBREVIATIONS

AMP AMPERE

AFF ABOVE FINISHED FLOOR

AWG AMERICAN WIRE GAUGE

BRK BREAKER

C CONDUIT

CB CIRCUIT BREAKER

CP CONDENSATE PUMP

D EXISTING TO BE DEMOLISHED

DISCSW DISCONNECT SWITCH

DP DISTRIBUTION PANEL

DWG DRAWING

E, EX EXISTING TO REMAIN

EG EQUIPMENT GROUND

EM DEVICE ON EMERGENCY CIRCUIT

EMT ELECTRICAL METALLIC TUBING

EW EMERGENCY WHITE (NIGHT) LIGHT

EWH ELECTRIC WATER HEATER

FAAP FIRE ALARM ANNUNCIATOR PANEL

FACP FIRE ALARM CONTROL PANEL

FATC FIRE ALARM TERMINAL CABINET

FLA FULL LOAD AMPS

G, GND GROUND

GFI GROUND FAULT INTERRUPTER

HP HORSE POWER

IG INTERRUPTER ISOLATED GROUND

KVA KILOVOLT-AMPS

KW KILOWATT

MCB MAIN CIRCUIT BREAKER

MD MOTORIZED DAMPER

MLO MAIN LUGS ONLY

MDP MAIN DISTRIBUTION PANEL

N NEW

NEC NATIONAL ELECTRICAL CODE

NF NON FUSED

N/L NIGHT LIGHT FIXTURE ON A TIMER

NTS NOT TO SCALE

P POLE

PH, Ø PHASE

PNL PANEL

PSRH PROJECT STANDARD RECEPTACLE HEIGHT

PSSH PROJECT STANDARD SWITCH HEIGHT

R RELOCATED AT NEW LOCATION

RR REMOVE AND RELOCATE

S.N. SOLID NEUTRAL

SM MOTOR THERMAL SWITCH CONTROL

SWBD SWITCHBOARD

TEL TELEPHONE

T, XFMR TRANSFORMER

TYP TYPICAL

U.H. UNIT HEATER

U.O.A. UNLESS OTHERWISE NOTED

V VOLTS

W WATTS

WP WEATHERPROOF

DIMENSION CLARIFICATION

ALL DIMENSION LINES SHOW DEFAULT OF U.S. STANDARD UNITS, WITH METRIC UNITS AS

SECONDARY INDICATED BY THERE LOCATION BETWEEN THE FOLLOWING SYMBOLS [ ]

SEE EXAMPLE BELOW FOR CLARIFICATION:

20'-0" [6.10]

STANDARD METRIC (METERS)

-GENERAL ELECTRICAL SYMBOLS

-ELECTRICAL SCHEMATIC SYMBOLS

C0

AP

5E

(ALL ABBREVIATIONS MAY NOT APPEAR ON THE DRAWINGS)

ELECTRICAL COORDINATION NOTES:

-GENERAL

1. ALL CONDUIT, J BOXES, SITE PREPARATIONS, AND HIGH VOLTAGE COMPONENTS SHALL BE

PROVIDED BY THE CUSTOMER OR ELECTRICAL CONTRACTOR UNLESS OTHERWISE SPECIFIED IN

THE DRAWINGS.

2. ALL COMPONENTS ASSOCIATED WITH SYSTEMS AND EQUIPMENT TO BE REMOVED OR

RELOCATED MAY NOT BE SPECIFICALLY INDICATED. REMOVE ALL ASSOCIATED ELECTRICAL

COMPONENTS, HANGERS, WIRING, CABLING, CONDUIT, BOXES, DEVICES AND ALL OTHER

ITEMS RELATED TO EQUIPMENT AND MATERIALS WHICH ARE INDICATED TO BE REMOVED OR

RELOCATED. REMOVE ALL WIRING/CONDUIT BACK TO THE SOURCE IN EXISTING CIRCUITS

WHICH ARE BEING DEMOLISHED. UNLESS SPECIFICALLY INDICATED, NO EQUIPMENT,

MATERIALS OR ASSOCIATED COMPONENTS SHALL BE ABANDONED IN PLACE.

-DISPOSAL OF DEMOLITION

1. CONTRACTOR SHALL CLEAN THE PROJECT SITE AT THE END OF EACH WORKING DAY.

CONTRACTOR SHALL NOTIFY BUILDING OWNER PRIOR TO DISPOSAL OF ALL DEMOLISHED

MATERIALS TO ALLOW THE OWNER TO SALVAGE ANY USABLE MATERIALS. AFTER INSPECTING

FROM THE OWNER'S REPRESENTATIVE ALL UNUSED MATERIALS SHALL BE REMOVED FROM

THE JOB SITE WITH DISPOSAL IN ACCORDANCE WITH APPLICABLE SPECIFICATIONS AND

REGULATIONS.

-PROTECTION

1. PROTECT FROM DAMAGE ALL EXISTING WORK TO REMAIN. ANY EXISTING TO REMAIN OR

EXISTING TO BE RELOCATED MATERIALS AND EQUIPMENT DAMAGED DURING THE COURSE

OF THE WORK SHALL BE REPLACED WITH MATERIALS AND EQUIPMENT CONFORMING TO

THESE SPECIFICATIONS AT NO ADDITIONAL COST TO THE OWNER. CARE MUST TAKEN IN

REMOVING ALL EXISTING MATERIALS.

AP ACCESS PORT

EQUIPMENT

PROVIDED - BY OTHERS

EQUIPMENT

PROVIDED - BY ACTION TARGET

CONDUIT/CONTROLS

PROVIDED - BY OTHERS

CONDUIT

PROVIDED - BY OTHERS

ACCESS PORT

PROVIDED - BY ACTION TARGET

CAT5E JACK & WALL PLATE

PROVIDED - BY OTHERS

WP

SPKR SPEAKER

PROVIDED -BY ACTION TARGET

MICROPHONE

PROVIDED -BY ACTION TARGET

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z700

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

GENERAL

ELECTRICAL NOTES

FIRING

LINE

TARGET

LINE

3 YD

FIRING

LINE

RCP2

JB

RCP2

ACP

ACB

PWR2

PWR1TCM1

RCP1

SRC ETH

RCP1

Z701

1 ELECTRICAL RANGE PLAN

Scale - 3/16" = 1'-0"

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z701

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

ELECTRICAL

RANGE PLAN

CONTROL ROOM

Z701

2 CONTROL ROOM

Scale - 3/4" = 1'-0"

Z701

TCM CHANNEL 1

TCM CHANNEL 2

TCM CHANNEL 3

TCM CHANNEL 4

TCM CHANNEL 5

TCM CHANNEL 6

TCM CHANNEL 7

TCM CHANNEL 8

TCM CHANNEL 9

TCM CHANNEL 10

TCM CONTROL CARD

TCM PROGRAMMING

BUTTON

NETWORK RJ45

CONNECTION

WIRING LAYOUT FOR TCM BANK 1

RANGE TARGET TCM CHANNEL CABLE COLOR

1 COMMON N/A N/A 1+ BLACK

1 COMMON N/A N/A 1+ RED

1 1 10.0.0.11 1 1+ BLUE

1 1 10.0.0.11 1 IN 4- ORANGE

1 2 10.0.0.11 2 1+ YELLOW

1 2 10.0.0.11 2 IN 4- BROWN

1 COMMON N/A N/A 2+ BLACK

1 COMMON N/A N/A 2+ RED

1 3 10.0.0.11 3 1+ BLUE

1 3 10.0.0.11 3 IN 4- ORANGE

1 4 10.0.0.11 4 1+ YELLOW

1 4 10.0.0.11 4 IN 4- BROWN

1 COMMON N/A N/A 3+ BLACK

1 COMMON N/A N/A 3+ RED

1 5 10.0.0.11 5 2+ BLUE

1 5 10.0.0.11 5 IN 5- ORANGE

1 6 10.0.0.11 6 2+ YELLOW

1 6 10.0.0.11 6 IN 5- BROWN

1 COMMON N/A N/A 4- BLACK

1 COMMON N/A N/A 4- RED

1 7 10.0.0.11 7 2+ BLUE

1 7 10.0.0.11 7 IN 5- ORANGE

1 8 10.0.0.11 8 2+ YELLOW

1 8 10.0.0.11 8 IN 5- BROWN

1 COMMON N/A N\A 5- BLACK

1 COMMON N/A N/A 5- RED

1 9 10.0.0.11 9 3+ BLUE

1 9 10.0.0.11 9 IN 6- ORANGE

1 10 10.0.0.11 10 3+ YELLOW

1 10 10.0.0.11 10 IN 6- BROWN

TCM CHANNEL 1 IN

TCM CHANNEL 2 IN

TCM CHANNEL 3 IN

TCM CHANNEL 4 IN

TCM CHANNEL 5 IN

TCM CHANNEL 6 IN

TCM CHANNEL 7 IN

TCM CHANNEL 8 IN

TCM CHANNEL 9 IN

TCM CHANNEL 10 IN

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z704.1

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

TARGET CONTROL

MODULE DETAILS

Z704.1

1 TARGET CONTROL MODULE

Scale - NONE

CONTROL ROOM AREA

TARGET LINE AREA

AC POWER PROVIDED

-BY OTHERS

RETRIEVERS/WIRES PROVIDED

-BY ACTION TARGET

CONDUIT/WIRES PROVIDED

-BY OTHERS

C# CONDUIT PROVIDED

-BY OTHERS

ELECTRICAL KEY

R

AC

EW

AY

(R W

TARGET CONTROL MODULE

(TCM)

CP1

CP2

SMART RANGE COMPUTER

(SRC)

E E E

(PWR1)

POWER SUPPLYDIRECT SERVICE

13.8V @ 20 AMP D.C.

(PWR2)

POWER SUPPLYDIRECT SERVICE

13.8V @ 40 AMP D.C.

EXTERNAL INTERNET

CONNECTION

-BY OTHERS

E E

AIR COMMAND CORDLESS PHONE

(ACP)

AIR COMMAND INTERFACE BOX

(ACB)

ETHERNET SWITCH

(ETH)

POWER 90

(X10)

(RCP1) NEMA 5-20R

125V @ 16 FLA

(RCP1) NEMA 5-20R

125V @ 16 FLA

CP1

CP2

(JB)

JUNCTION BOX

(JB)

JUNCTION BOX

CONDUIT SCHEDULE - BY OTHERS

ITEM QTY DESCRIPTION

CP1 2 3" CONDUIT

CP2 2 1-1/2" CONDUIT

CONDUIT FILL SCHEDULE - BY ACTION TARGET

ITEM QTY DESCRIPTION

CP1

5 16/6 GA WIRE

CP2

2 1/2" AIRLINE

EQUIPMENT SCHEDULE - BY ACTION TARGET

ITEM QTY ABBREV

POWER 90 10

RACE WAY 1 RW

TARGET CONTROL MODULE 1 TCM

POWER SUPPLY 2 PWR

SMART RANGE COMPUTER 1 SRC

ETHERNET SWITCH 1 ETH

AIR COMMAND INTERFACE BOX 1 ACB

AIR COMMAND CORDLESS PHONE 1 ACP

AIR COMPRESSOR 1 AC

AUTO DRAIN 1 AD

REFRIDERATED DRYER 1 DRY

JUNCTION BOX 12X12X6 3 JB

ELECTRICAL RECEPTACLE SCHEDULE - BY

OTHERS

ITEM QTY DESCRIPTION

RCP1 2 NEMA 5-20 ISOLATED GROUND DUPLEX RECEPTACLE FOR ETHERNET SWITCH

RCP2 2 NEMA 5-20 ISOLATED GROUND DUPLEX RECEPTACLE FOR AD DRYER AND DRAIN

RANGE AIR

(AC)

AIR COMPRESSOR

(DRY)

REFRIGERATED DRYER

(JB)

JUNCTION BOX

(AD)

AUTO DRAIN

(RCP2) NEMA 5-20R

125V @ 20 FLA GROUND

(RCP2) NEMA 5-20R

125V @ 20 FLA GROUND

(GB)

GANGE BOX

EQUIPMENT POWER SCHEDULE - BY OTHERS

PRODUCT LINE PRODUCT QTY PHASE VOLTS AMPS

POWER SUPPLY PSR 1 1 1 13.8 20 AMP D.C.

POWER SUPPLY PSR 2 1 1 13.8 40 AMP D.C.

REFRIGERATED

DRYER DRY 1 1 120 20 AMP

AUTO DRAIN AD 1 1 120 20 AMP

AIR COMPRESSOR AC 1 1 120 2 HP

DIRECT SERVICE

120V @ 2 HP

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z745.5

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

POWER 90

ELECTRICAL

SCHEMATIC

CONDUIT FOR DCU SWITCH

-BY OTHERS

JUNCTION BOX

DUPLEX RECEPTACLE FOR

REFRIGERATED DRYER

-BY OTHERS

WATER SEPARATORS

JUNCTION BOX

CONDUIT FOR RANGE AIR

-BY OTHERS REFRIGERATED DRYER

CONDUIT FOR DCU SWITCH

-BY OTHERS

AUTO DRAIN

DUPLEX RECEPTACLE FOR AIR

COMPRESSOR AND AUTO DRAIN

-BY OTHERS

2 HORSEPOWER

AIR COMPRESSOR

WATER SEPARATORS

DUPLEX RECEPTACLE

FOR REFRIGERATED

DRYER

-BY OTHERS

JUNCTION BOX

CONDUIT FOR RANGE AIR

-BY OTHERS

REFRIGERATED DRYER

CONDUIT FOR DCU STOP SWITCH

-BY OTHERS

JUNCTION BOX

CONDUIT FOR DCU SWITCH

-BY OTHERS

AUTO DRAIN

DUPLEX RECEPTACLE FOR AIR

COMPRESSOR AND AUTO DRAIN

-BY OTHERS

2 HORSEPOWER

AIR COMPRESSOR

SCALED FOR ORIGINAL DRAWING AT 22" X 34"

Z757.1

CLARENDON CSO, SC

100% SUBMITTAL

SA

VE

D : 2

4-

-2

:4 4:

B

Y:

J

AL

LR

ED

A

T:

T

:\P R

O

JE

C

TS

\O pe n\ C la re nd on

C

SO

, S C

\C

AD

_W or ki ng

\C la re nd on C

SO

, S

C _1

_R ev 3.

dw g

13092

Project Manager:

Territory Manager:

Project Engineer:

Drawn By:

Approved By:

Origination Date:

JAMIE HADERLIE

02/08/24

JA

AARON LUDWIG

ROB DECOSTA

DAVID JOHNSON

REVISION DATENo BY

PROJECT STATUS

PROJECT NAME

DRAWING NUMBER

SHEET NAME

SHEET NUMBER

3 JA SWITCH OUT EQUIPMENT 06/20/24

2 JA CHANGE NOTES 06/18/24

1 JA BRING TO 100% 03/05/24

P O

B ox

, P ro vo U

T, O ffi ce

1)

-8

F ax

1)

-8 w w w

.A ct io nT ar ge t.c om

Th e us e of th es e pl an s sh al l b e re st ric te d to th e or ig in al p ro je ct s ite fo r w hi ch th ey w er e pr ep ar ed

Pu bl ic at io ns e xp re ss ly li m ite d to s uc h us e.

R e-us e, re pr od uc tio n, o r p ub lic at io n by a ny m et ho d in w ho le or p ar t i s pr oh ib ite d.

d ra w in gs a nd d es ig ns re m ai n th e pr op er ty o f a ct io n ta rg et in c.

w ith ou t r es er va tio n.

Ac tio n Ta rg et

In c.

Al l R ig ht s

R es er ve d

COMPRESSOR

ROOM DETAILS

Z757.1

2 COMPRESSOR ROOM PLAN

Scale - 1-1/2" = 1'-0"

Z757.1

2 COMPRESSOR ROOM SECTION

Scale - 1-1/2" = 1'-0"