Camden Ave Specs.pdf

Customer:__________________________________ Contractor:__________________________________

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 1 of 58

Work Write-Up 3477 Camden Avenue

* EXHIBIT 1 *

Dated: 11/8/2024

CUSTOMER INFORMATION

3477 Camden Avenue

Burton, MI 48529

PREPARED BY

lparks@geneseecountymi.gov

* NOTE *

THE CUSTOMER AND CONTRACTOR MUST SIGN THE BOTTOM OF EACH PAGE ONLY IF

1) THIS WORK WRITE-UP BECOMES PART OF A CONSTRUCTION CONTRACT

2) THE UNDERSIGNED CUSTOMER AND CONTRACTOR HAVE REVIEWED, APPROVED AND

AGREED TO THE WORK AND PRICES DESCRIBED IN THIS WORK WRITE-UP

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 2 of 58

Location: General Requirements General Requirements Quantity Cost/Units Total

1 - CLEAN TO CLEARANCE

(Specification ID:1.05600 Estimated Qty:1300)

1,300

Prior to final acceptance of the lead hazard reduction work and all rehabilitation work, the property shall be visually inspected for any remaining paint chips, dust and debris and lead dust wipe samples shall be obtained from floors, windows sills and window troughs. The contractor shall re-clean all applicable components and surfaces and pay for all additional clearance dust sampling if any dust sample results exceed the thresholds of 10 ug/SF for floors, 100 ug/Sf for windowsills, 100 ug/SF for window troughs and 40 ug/SF for porch floors.

NOTE: SEE LEAD RISK ASSESSMENT / INSPECTION REPORT.

No Category Quantity Cost/Units Total

2 - BONDING REQUIREMENTS

(Specification ID:0 Estimated Qty:1)

A. Performance Bond: The successful proposer must provide a Performance Bond insuring the Contractor's performance of awarded structures/projects.

B. Payment Bond: The successful proposer must provide a Materials & Labor Payment Bond insuring that the Contractor's subcontractors will be paid according to their subcontract.

D. General Conditions: The Performance and Payment Bonds must be issued by a surety authorized to issue bonds in the State of Michigan and must have a penal amount at least equal to 100% of the total amount due to the Contractor under this Agreement. In addition, the surety bonds must be submitted to the County as a condition of contract execution. The County reserves the right to reject any surety proposed by the successful proposer if the County, in its sole discretion, determines that the surety proposed by the successful proposer is unable to provide adequate protection for the County All bonds listed above will be required. The bid amount should reflect the bonding costs to cover all bonds listed.

The winning bidder shall provide all required bonding document prior to signing construction contracts. ect.

3 - FINAL CLEAN

(Specification ID:0 Estimated Qty:0)

Remove from site all construction materials, tools and debris. Sweep clean all exterior/ interior work areas.

Vacuum all interior work areas, removing all visible dust, stains, labels and tags. Clean all windows referenced in specifications.

NOTE: Clean the entire house.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 3 of 58

4 - PERMITS AND LICENSES

(Specification ID:0 Estimated Qty:1)

The contractor is responsible for applying, paying for and receiving all applicable permits that authorize the activity, including but not limited to a building permit, electrical permit, plumbing permit, or mechanical permit. The contractor shall apply, pay for, and receive permits prior to starting the work.

5 - VERIFY QUANTITIES/MEASURMENTS

(Specification ID:0 Estimated Qty:0)

All Quantities stated in the attached specifications for this address using Units of Measure other than Each (EA), Room (RM) or Dwelling Unit (DU) (e.g. SF of Drywall) are for the contractor's convenience and must be verified by the contractor at a mandatory site inspection prior to bid submission. All quantities stated in the Units of Measure Each (EA), Room (RM) or Dwelling Unit (DU) are as stated. Discrepancies in Quantities found by the contractor must be communicated to the Housing Rehabilitation Specialist prior to the submission of a bid. Claims for additional funds due to discrepancies in Quantities shall not be honored if submitted after the bid submission.

Subtotal for No Category

Location: Building Exterior Doors Quantity Cost/Units Total

6 - DOOR -- PREHUNG METAL ENTRANCE -- ENERGY

STAR

(Specification ID:45.02500 Estimated Qty:2)

Install a Jeld Wen ENERGY STAR certified insulated prehung steel door, a passage latch and double cylinder dead bolt keyed to match the deadbolts of other exterior doors. Include new casing/trim and finish paint/stain to match existing as close as possible. Paint brick mould to match existing trim.

NOTE: Use Lead Safe Practices and Install new prehung steel doors on the front and south sides of the home.

7 - INSTALL A NEW STORM DOOR

(Specification ID:45.04750 Estimated Qty:2)

Install a combination storm and screen door with white baked enamel aluminum finish and top chain. If storm is in front of entrance door with decorative oval glass it should be full view glass not split screen.

Subtotal for Doors

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 4 of 58

Exterior Walls Quantity Cost/Units Total

8 - INSTALL DELUXE HOUSE NUMBERS

(Specification ID:30.02350 Estimated Qty:1)

Install 4" solid brass house numbers.

9 - INSTALL VINYL SIDING AND RELATED COMPONENTS

(Specification ID:30.12750 Estimated Qty:17)

Install vinyl siding, porch ceilings, corner boards and other typical vinyl components. Stagger siding joints and conceal joints from street view. Install "Tyvek" or equal air barrier. Install 1/4" perforated foil backed foam insulation board at house corners. Use at least .044-millimeter-thick siding and components manufactured by Georgia Pacific, Mastic, Wolverine, CertainTeed or other approved equal. Siding to have a 50-year manufacturer's warranty and be installed per manufacturer's specifications. Genesee County staff to select siding and trim color.

NOTE: Use Lead Safe Work Practices.

Subtotal for Exterior Walls

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 5 of 58

Porches & Entrances Quantity Cost/Units Total

10 - INSTALLL NEW FRONT DECK

(Specification ID:40.00750 Estimated Qty:1)

Install 5/4" preservative treated deck with handrail, guard rails and spindles. Face nailing with hot dipped galvanized fasteners into solid porch joists. Include all trim and skirting necessary to create a neat appearance where the deck adjoins other surfaces. Install steps leading up to the new deck with preservative treated wood. All construction must comply with Michigan building codes.

NOTE: The new porch must be the same size as the existing front concrete porch.

11 - REMOVE CONCRETE PORCH AND STEPS

(Specification ID:40.03000 Estimated Qty:1)

Break up and remove concrete porch and steps.

NOTE: Remove debris and properly dispose of construction debris.

Subtotal for Porches & Entrances

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 6 of 58

Roof & Attic Quantity Cost/Units Total

12 - REMOVE EXISTING SHINGLES AND INSTALL NEW

SHINGLES ON ROOF DECKING

(Specification ID:35.00000 Estimated Qty:12)

Remove and dispose of all roofing & defective sheathing. Cut a 1" wide vent at ridge board (for ridge/soffit venting only). Replace up to 5 sf of sheathing per 100 sf of roof using pine board or OSB of matching thickness. Staple 15 lb felt. Install preformed white aluminum drip edge and replace all vent pipe boots.

Install a 15 lb fiberglass asphalt, dimensional shingle with limited lifetime warranty. Replace all flashing.

Install shingle-over ridge vent (for ridge/soffit vent only) or slant back style roof vent (to match shingle color). Genesee County staff to choose shingle color.

THE CONTRACTOR IS RESPONSIBLE FOR APPLYING, PAYING & RECEIVING ALL APPLICABLE

PERMITS THAT AUTHORIZE THE ACTIVITY.

THE HOMEOWNER IS RESPONSIBLE FOR DISCONNECTING & RE-CONNECTING ALONG WITH

ANY FEES FOR ITEMS SUCH AS ROUTER BOXES, SATELLITE, TV, INTERNET

ANTENNAS/DISHES ETC.

13 - REMOVE CHIMNEY FROM TOP OF HOUSE TO 6"

BELOW BOTTOM OF FLOOR JOISTS

(Specification ID:35.13250 Estimated Qty:1)

Remove chimney below bottom floor of house and remove loose brick and debris to legal dump site. Frame-in roof, ceiling and floor openings using building code approved materials and methods of construction.

Apply surface and finish materials to close holes at roof, ceiling and floor. New surface and finish materials to match and blend in with adjoining materials as closely as possible.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 7 of 58

14 - GUTTER/DOWNSPOUT--5" SEAMLESS

(Specification ID:35.14000 Estimated Qty:148)

Install a new fascia mounted aluminum gutter system at all eaves. Dispose of original and replace with 5", K Type, seamless, .027 aluminum gutters, downspouts, concrete splash blocks and accessories to service entire dwelling. Install downspouts at each corner and major offset with straps 3' on center and extensions at least 3' in length. Genesee County staff to choose color.

NOTE: 60' of gutters and 88' of downspouts.

Subtotal for Roof & Attic

Site Work Quantity Cost/Units Total

15 - DEMO GARAGE

(Specification ID:20.06500 Estimated Qty:1)

Demolish garage and remove all debris to legal dump site. Break up concrete slab where garage sat and remove off site to code legal dump. Level soil below and build up even with height of surrounding yard. Seed and straw area affected by demolition.

Windows Quantity Cost/Units Total

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 8 of 58

16 - WET SCRAPE LOOSE PAINT FROM WOOD AROUND

THE FRONT DOOR AND PAINT

(Specification ID:50.07500 Estimated Qty:1)

Wet scrape loose, peeling, blistering and flaking paint from wood front door casing and crown molding.

Apply 2 coats of exterior paint to the front door casing and crown molding.

17 - EXTERIOR LIGHT FIXTURE

(Specification ID:0 Estimated Qty:2)

Remove fixture and install a UL listed, one bulb, incandescent exterior light fixtures. Include LED bulbs.

NOTE: Install lights on the front and back of the home.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 9 of 58

18 - INSTALL FRONT PORCH COLUMNS

(Specification ID:0 Estimated Qty:2)

Install 4"x4" column supports on the front porch to support the front door overhang. Wrap the 4"x4" posts with 1"x6" pine boards. Apply 1 coat of primer and 2 coats of exterior paint on the 1"x6" boards and seal all corners and edges. Properly secure the support posts.

19 - NEW ASPHALT DRIVEWAY

Apply a vegetation killer to existing driveway where necessary. Install 4 - 6"aggregate material and compact where needed. Install 3" of residential-grade asphalt in 1 compact course on top of existing concrete driveway. Install professional quality sealer after new asphalt is installed.

Location: Living Room Electrical System Quantity Cost/Units Total

20 - Replace existing receptacle with new duplex (Specification ID:1.00060 Estimated Qty:4)

Replace receptacle with colored matched duplex receptacle and cover plate.

21 - LIGHT FIXTURE SWITCH

(Specification ID:80.00250 Estimated Qty:1)

Replace light fixture switch and cover plate.

Subtotal for Electrical System

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 10 of 58

Floors & Stairs Quantity Cost/Units Total

22 - REFINISH WOOD FLOOR

(Specification ID:55.04000 Estimated Qty:120)

Professionally refinish wood flooring. This includes removing existing floor finish, patching and sanding floor, and sealing floor with polyurethane finish per manufacturer's instructions. Replace shoe molding around the floor.

NOTE: Repair any breaks or missing wood plank boards.

HVAC & Gas System Quantity Cost/Units Total

23 - REGISTER COVER REPLACEMENT

(Specification ID:85.10010 Estimated Qty:3)

Replace missing or damaged register cover with an adjustable metal register. If return air wall register, caulk in place prior to painting.

NOTE: Replace 2 floor and 1 wall register.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 11 of 58

Walls Quantity Cost/Units Total

24 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:50)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joint of shoe mold and vinyl floor covers. Use finish nails to install baseboard and shoe mold. Paint baseboard with 2 coats of semi-gloss acrylic latex paint.

Walls and Ceilings Quantity Cost/Units Total

25 - PREP /PAINT WALLS CEILING SURFACE WITH SEMI-

GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:1)

Apply 2 coats of semi-gloss latex paint on all walls and ceiling surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any minor repairs to walls and ceiling surfaces prior to painting. Genesee County staff to choose color.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 12 of 58

26 - WINDOW--VINYL--LOW E SINGLE HNG DBL GLZ

ENERGY STAR - W/TRIM

(Specification ID:50.01500 Estimated Qty:1)

Field measure, order, and install a PVC, 1 over 1, single hung, double glazed, argon filled Low E window that meets the ENERGY STAR standards for this climate for U value and SHGC. Include 1/2 screen. Wrap exterior jamb and sill with .027" aluminum coil stock back caulked and nailed 6" on center. Retrim opening with casing or shoe/door stop as necessary. Paint or stain/poly any raw or primed wood to match existing trim.

NOTE: Please see Lead Report and use Lead Safe work practices.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 13 of 58

27 - WINDOW--3 LIGHT VINYL SLIDER

(Specification ID:50.02000 Estimated Qty:1)

Field measure, order, remove and install a vinyl,3 light slider, double glazed, window. Including screen, caulk, interior casing and exterior trim, wrapped in aluminum. Wrap exterior jamb and sill with .027" aluminum coil stock back caulked and nailed 6" on center. Retrim opening with casing or shoe/door stop as necessary. Paint or stain/poly any raw or primed wood to match existing trim.

NOTE: Please see Lead Report and use Lead Safe work practices.

Subtotal for Windows

Location: Hallway Ceilings Quantity Cost/Units Total

28 - PREPARE AND PAINT SURFACE INSIDE/OUTSIDE OF

LINEN CABINET

(Specification ID:65.04500 Estimated Qty:1)

Prep cabinet surface. Remove all contact paper. Repair and fill all cracks and holes with appropriate material.

Remove loose paint and sand any rough spots. Apply stain killer and 2 coats of semi-gloss paint inside and outside of the linen cabinet.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 14 of 58

29 - DOOR--PREHUNG 6 PANEL INT, HOLLOW

(Specification ID:45.07000 Estimated Qty:1)

Install 6-panel, hollow core, masonite, prehung door. Include privacy lockset and 3 butt hinges. Include casing on both sides. Include appropriate doorstop, hinge bump or base bump to match color of hinges.

Apply 2 coats of paint, per 6 sides of door.

NOTE: Replace door trim around the door.

30 - REPLACE LINEN CABINET

Replace linen cabinet with 2 stackable wall cabinets and trim out with tall fillers.

31 - LIGHT FIXTURE/ SWITCH REPLACEMENT

(Specification ID:80.00500 Estimated Qty:1)

Replace existing with a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $30 allowance for fixture. Include LED bulbs.

NOTE: Replace light switch and matching cover plate.

32 - INSTALL SMOKE DETECTORS TIED TOGETHER

(Specification ID:80.11750 Estimated Qty:1)

Install a UL listed electric hard wired smoke detector with a battery backup. Detectors are also to have test buttons, hush buttons and flashing LED indicator. All smoke detectors to be tied together on same circuit and tied into "house" panel. Use materials and methods of installation that comply with electrical code requirements.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 15 of 58

33 - REFINISH WOOD FLOOR

(Specification ID:55.04000 Estimated Qty:60)

Professionally refinish wood flooring. This includes removing existing floor finish, patching and sanding floor, and sealing floor with polyurethane finish per manufacturer's instructions.

34 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:20)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joint of shoe mold and vinyl floor covers. Use finish nails to

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 16 of 58

35 - PAINT WALLS AND CEILING SURFACE WITH SEMI-

GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:1)

Apply 2 coats of semi-gloss latex paint on all walls and ceilings surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any minor repairs to the walls and ceiling surfaces prior to painting.

NOTE: Prep and paint inside of the closet. Replace closet shelves and paint all sides.

Location: Kitchen Appliance Exhaust Vent Quantity Cost/Units Total

36 - GENERAL APPLIANCE WORK

(Specification ID:95.00000 Estimated Qty:1)

Remove wall mounted exhaust vent, patch hole in the drywall and prep area for paint.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 17 of 58

37 - INSTALL A RANGE HOOD

(Specification ID:95.90125 Estimated Qty:1)

Install a new 2 speed 30" range hood with light. Genesee County staff to choose color.

Subtotal for Appliance Exhaust Vent

Appliances Quantity Cost/Units Total

38 - INSTALL AN ELECTRIC RANGE

(Specification ID:95.90050 Estimated Qty:1)

Purchase and install a 30" self-cleaning electric range. Provide electric connections to comply with the local electrical code. Genesee County staff to choose color.

NOTE: Color to match refrigerator.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 18 of 58

39 - INSTALL NEW ELECTRIC REFRIGERATOR

(Specification ID:95.99990 Estimated Qty:1)

Purchase and install a new electric ENERGY STAR refrigerator with freezer. Refrigerator shall have at least an 18 cubic foot capacity. Hinge door shall be on right side. Genesee County staff to choose color.

NOTE: Color to match range.

Subtotal for Appliances

Cabinets Quantity Cost/Units Total

40 - INSTALL WALL,BASE AND IN WALL CABINETS AND

COUNTERTOP

(Specification ID:70.01250 Estimated Qty:13)

Field measure and install high quality kitchen base cabinet built by a professional cabinet maker or cabinet manufacturer meeting ANSI A161.1 standards. Cabinet to have 3/4" solid wood Birch frames and 3/4" Birch plywood end panels. Door and drawer faces to be made from Birch wood. Shelves to be 1/2" finish grade wood with smooth edges. Particleboard is not permitted. Cabinets, other than sink base cabinets, to have one drawer. All visible wood surfaces to be protected with water resistant coating. Install a post formed rolled edge plastic laminated countertop with back and end splashes. Apply a bead of mildew resistant caulk where top of splashes meets wall surfaces. Trim out splashes prior to caulking if more than 1/4" gap exists between splash and wall. Genesee County staff to choose cabinet and countertop colors.

NOTE: See kitchen cabinet layout provided.

CUSTOM Quantity Cost/Units Total

41 - DEMO CABINETS AND COUNTERTOP

(Specification ID:0 Estimated Qty:1)

Remove and properly dispose of the kitchen countertop and all existing wall and base cabinets.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 19 of 58

42 - Replace existing duplex receptacles (Specification ID:1.00060 Estimated Qty:2)

Replace duplex receptacles with color matched duplex receptacles and cover plates.

43 - LIGHT FIXTURE/LIGHT SWITCH COVER--REPLACE

(Specification ID:80.00500 Estimated Qty:2)

Replace existing light fixture with ceiling mounted, UL approved, incandescent light fixture and light switches with cover plates. Include LED bulbs.

NOTE: Install 1 light fixture under the kitchen cabinets.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 20 of 58

44 - INSTALL GFCI DEVICE

(Specification ID:80.06750 Estimated Qty:1)

Install an additional surface mounted GFCI receptacle with cover at the countertop to match existing color.

Make connection downstream of existing kitchen circuit so that both receptacles are protected.

45 - INSTALL A NEW ELECTRIC RANGE PLUG-IN AND

WIRING

(Specification ID:80.07000 Estimated Qty:1)

Install a new 220-V 50-Amp electric range circuit including receptacle and wiring that includes a ground wire. Run new wiring behind building surface materials unless otherwise approved by Program Administrator. Materials and method of installation must also meet with approval of electrical inspector.

46 - INSTALL 3-WAY LIGHT SWITCH

Install 3-way light switch to control main kitchen light. One light switch should be installed at the rear entry way into the kitchen and the other switch should be installed at the hallway entry to the kitchen area.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 21 of 58

47 - REMOVE FLOOR COVERING TO SUBFLOOR

(Specification ID:1.00040 Estimated Qty:120)

Remove floor covering to subfloor, remove all staples/nails and inspect subfloor for water/mold damage.

Remove all transitions. Spot screw exposed subfloor to eliminate squeaks and loose areas.

48 - INSTALL NEW UNDERLAYMENT OVER EXISTING

SUBFLOOR

(Specification ID:55.02000 Estimated Qty:120)

Install new underlayment grade plywood or wafer board that is at least 3/8" thick on top of existing subfloor.

Secure underlayment to subfloor using screws or screw shank nails spaced 4" on center along edges and 6" on center across entire surface. Stagger and fill all joints and indentations with floor patch and sand smooth.

Lauan and hardboard panel are not acceptable. Call Program Administrator for compliance inspection upon task completion.

49 - Vinyl Plank Flooring - 100% Waterproof (Specification ID:55.11200 Estimated Qty:126)

Install new vinyl plank flooring. New vinyl plank floor will be 100% waterproof - Home Depot Home Lifeproof style vinyl plank flooring or approved equal 4.2 mm thickness or greater. Include all transition pieces at hallways. ($3.50 SQ FT material allowance - including tax) Genesee County staff to choose color.

Subtotal for Floors & Stairs

50 - Register cover replacement (Specification ID:85.00000 Estimated Qty:1)

Replace missing or damaged register cover with an adjustable metal register. If return air wall register, caulk

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 22 of 58

Plumbing System Quantity Cost/Units Total

51 - SINK--DOUBLE BOWL COMPLETE

(Specification ID:75.01250 Estimated Qty:1)

Install a 22-gauge 33" x 22" x 7" double bowl, stainless steel, self rimming kitchen sink including a single lever steel, metal body faucet, rated at 2.0 GPM or less, with a 15-year drip-free warranty, grease trap, supply lines, full port ball type shut-off valves & escutcheon plates on all supply & drain lines.

52 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:32)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joint of shoe mold and vinyl floor covers. Use finish nails to

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 23 of 58

53 - PAINT WALLS AND CEILING SURFACES WITH SEMI-

GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:500)

Prepare walls and apply 2 coats of semi-gloss latex paint on all wall and ceiling surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any minor repairs to the walls and ceiling surfaces prior to painting. Genesee County staff to choose color.

54 - WINDOW--VINYL--LOW E SINGLE HNG DBL GLZ

ENERGY STAR - W/TRIM

(Specification ID:50.01500 Estimated Qty:2)

Field measure, order, and install two (2) PVC, 1 over 1, single hung, double glazed, argon filled Low E windows that meet the ENERGY STAR standard for this climate for U value and SHGC. Include 1/2 screens for both. Wrap exterior jambs and sills with .027" aluminum coil stock back caulked and nailed 6" on center.

Retrim openings with casing or shoe/door stop as necessary. Replace interior trim to match existing trim, and/or wall color.

NOTE: See Lead Report and use Lead Safe Work Practices.

55 - PREPARE AND PAINT INSIDE CABINET

(Specification ID:50.08500 Estimated Qty:1)

Prep loose paint /contact paper from wood shelves, remove all contact paper. Secure loose material and caulk all cracks prior to applying primer. Apply primer that bonds to bare wood and existing paint. Then apply two coats of semi-gloss acrylic latex paint. Primer and paint to be applied using a roller or brush--spray painting not permitted. Primer and paint to be high quality and have a 10-year manufacturer's warranty.

Subtotal for Windows

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 24 of 58

Location: Bathroom

56 - DOOR--PREHUNG 6 PANEL INT, HOLLOW

(Specification ID:45.07000 Estimated Qty:1)

Install 6-panel, hollow core, masonite, prehung door. Include privacy lockset and 3 butt hinges. Include casing on both sides. Include appropriate doorstop, hinge bump or base bump to match color of hinges.

NOTE: Install new trim around both sides of the door.

57 - INSTALL NEW ENERGY STAR BATH VANITY

FIXTURE-LIGHT SWITCH

(Specification ID:80.02500 Estimated Qty:1)

Install a wall mounted vanity light bar, UL approved, light fixture with shade and lamps. Include LED bulbs.

NOTE: Install matching switch plate covers.

58 - NEWLIGHT/ BATH VENT FAN

(Specification ID:80.05750 Estimated Qty:1)

Install a ceiling through-the-wall, exterior ducted, fan/light vent with damper, and chrome faceplate capable of 60CFM at 60 sones. Include power with #14 copper wiring being connected the dual switch controlling the light fixture. New exhaust pipe shall be insulated R6 minimum. Repair any tear out.

59 - REPLACE RECEPTACLE WITH GFCI DEVICE

(Specification ID:80.06750 Estimated Qty:1)

Replace existing receptacle with a surfaced mounted ground fault circuit interrupt receptacle with cover plate to match existing color. Replace one downstream of existing kitchen circuit so that both receptacles are protected.

60 - SUBFLOOR--3/4"

(Specification ID:1.00050 Estimated Qty:1)

Install 3/4" tongue and groove cdx plywood (or osb) decking nailed 8" on center using screw shank or cement coated nails.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 25 of 58

61 - Vinyl Plank Flooring - 100% Waterproof (Specification ID:55.11200 Estimated Qty:25)

Install new vinyl plank flooring over new subfloor. New vinyl plank floor will be 100% waterproof - Home Depot Home Lifeproof style vinyl plank flooring or approved equal 4.2 mm thickness or greater. Include all transition pieces at hallways. ($3.50 SQ FT material allowance - including tax) Genesee County staff to choose color.

62 - Register cover replacement (Specification ID:85.00000 Estimated Qty:1)

Replace missing or damaged register cover with an adjustable metal register. If return air wall register, caulk

63 - VANITY--25" COMPLETE

(Specification ID:75.01500 Estimated Qty:1)

Install a 25" oak vanity including top with backsplash, wash bowl and single lever brass bodied chrome faucet with a maximum 1.5 GPM flow rate. Include PVC drain attached to a code legal plumbing vent, use type L copper or PEX supply piping with brass bodied stops on all supply lines. Seal all penetration through the floor, walls and cabinet for plumbing connections using expanding foam or caulk and cover with chrome Escutcheon plates.

64 - INSTALL A NEW TOILET - Minimum 16.5" From Floor to Rim (Specification ID:75.06500 Estimated Qty:1)

Install a new 2 piece closed coupled, vitreous china, water saving commode with maximum 1.6 gallons per flush manufactured by American Standard, Kohler or approved equal. Toilet to be designed for use by a person who has a disability with a minimum height of 16.5 inches from the floor to the seat rim. Commode to include all new components including a metal flush handle, pressed wood seat, plastic supply line, shut off valve, stub up, flange and wax seal. Top of toilet tank to be no more than 1" from back wall.

Subtotal for Plumbing System

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 26 of 58

65 - Interior walls/ceiling drywall (Specification ID:1.00000 Estimated Qty:1)

Install new 1/2" or 5/8" green board mold resistant drywall. Apply 3/8" adhesive bead and appropriate mechanical fasteners per manufacturers specification. Set seam tape in appropriate mud bed, sand and topcoat as needed for smooth finish. Include all prep and PRIMER FINISH ready for paint.

NOTE: All work must comply with local construction codes. Eliminate laundry chute.

66 - Install Bathtub with Shower Unit - 60" Complete with Surround (Specification ID:1.00100 Estimated Qty:1)

Install a 5', 4 piece, Sterling Accord® or approved equal, fiberglass shower unit complete with drain, PVC waste, single lever shower diverter, shower rod and a shower head with a maximum 2.0 GPM flow rate.

Exterior wall sections behind the tub shower unit and any plumbing penetrations must be completely air-sealed prior to installation. Per installation instructions set basin area in 1" to 2" of mortar cement. Include applicable fiberglass surround. Ensure shower base and surround are securely fastened to stud wall.

67 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:10)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joints of shoe mold and vinyl floor covers. Use finish nails to install baseboard and shoe mold. Paint baseboard with 2 coats of semi-gloss acrylic latex paint.

Subtotal for Walls

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 27 of 58

68 - DEMOLITION OF BATHROOM

(Specification ID:1.00030 Estimated Qty:1)

Remove all bath fixtures. Remove paneling, built-ins, drywall on walls and ceiling to the studs. Remove all nails and prepare for new drywall. Remove flooring to joists.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 28 of 58

69 - PREPARE AND PAINT WALL AND CEILING SURFACES

WITH SEMI-GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:1)

Properly prepare the walls and ceiling and apply 2 coats of semi-gloss acrylic latex paint on all paintable surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any minor repairs to the wall and ceiling surfaces prior to painting.

Subtotal for Walls and Ceilings

70 - INSTALL SHOWER ROD

(Specification ID:0 Estimated Qty:1)

Properly install an aluminum shower rod.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 29 of 58

Location: West Bedroom

71 - DOOR--PREHUNG 6 PANEL INT, HOLLOW

(Specification ID:45.07000 Estimated Qty:2)

Install 6-panel, hollow core, masonite, prehung door. Include privacy lockset and 3 butt hinges. Include casing on both sides. Include appropriate doorstop, hinge bump or base bump to match color of hinges.

NOTE: Replace door trim on both side of the door where applicable.

72 - INSTALL A NEW METAL RACK AND CLOTHING ROD

IN CLOSET

(Specification ID:45.08000 Estimated Qty:1)

Install a new metal shelving rack, clothing rod and necessary hardware in wall closet.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 30 of 58

73 - Replace existing receptacle with new duplex (Specification ID:1.00060 Estimated Qty:2)

Replace receptacles with color matched duplex receptacle and cover plate.

74 - REPLACE LIGHT FIXTURE/SWITCH

(Specification ID:80.00500 Estimated Qty:1)

Replace existing with a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and

NOTE: Replace matching switch cover plate.

75 - INSTALL AN ELECTRIC SMOKE DETECTOR

(Specification ID:80.11500 Estimated Qty:1)

Install a UL listed electric hard wired smoke detector with a battery backup. Detector to have a test button, hush button and flashing LED indicator. Use materials and methods of installation that comply with electric code requirements.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 31 of 58

76 - REFINISH WOOD FLOOR

(Specification ID:55.04000 Estimated Qty:120)

Professionally refinish wood flooring. This includes removing existing floor finish, patching and sanding

NOTE: Repair any holes located on the floor area.

77 - Register cover replacement (Specification ID:85.00000 Estimated Qty:2)

Replace missing or damaged register cover with an adjustable metal register. If return air wall register, caulk

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 32 of 58

78 - Interior wall drywall (Specification ID:1.00000 Estimated Qty:2)

Patch hole at the bottom of closet on both sides. Remove makeshift cabinet from east wall and open the hole left in the drywall to the studs. Prep wall and install new 1/2" or 5/8" drywall in the opening. Apply 3/8" adhesive bead and appropriate mechanical fasteners per manufacturers specification. Set seam tape in appropriate mud bed, sand and topcoat as needed for smooth finish. Include all prep and PRIMER FINISH ready for paint.

79 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:48)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joint of shoe mold and vinyl floor covers. Use finish nails to install baseboard and shoe mold. Paint baseboard with 2 coats of semi-gloss acrylic latex paint. Genesee County staff to choose color.

NOTE: Replace baseboard around the inside of the closet.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 33 of 58

80 - PREP AND PAINT WALL AND CEILING SURFACES

WITH SEMI-GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:1)

Apply 2 coats of semi-gloss acrylic latex paint on all wall and ceiling surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any repairs to the walls and ceiling surfaces prior to painting. Genesee County staff to choose the colors

NOTE: Paint the room and closet area.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 34 of 58

81 - WINDOW--VINYL--LOW E SINGLE HNG DBL GLZ

ENERGY STAR - W/TRIM

(Specification ID:50.01500 Estimated Qty:2)

Field measure, order, and install two (2) PVC, 1 over 1, single hung, double glazed, argon filled Low E windows that meet the ENERGY STAR standards for this climate for U value and SHGC. Include 1/2 screen. Wrap exterior jamb and sill with .027" aluminum coil stock back caulked and nailed 6" on center.

Retrim opening with casing or shoe/door stop as necessary. Paint or stain/poly any raw or primed wood to match existing trim.

NOTE: See Lead Report and use Lead Safe Work Practices. Replace trim around windows.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 35 of 58

Location: East Bedroom

82 - DOOR--PREHUNG 6 PANEL INT, HOLLOW

(Specification ID:45.07000 Estimated Qty:2)

Install 6-panel, hollow core, masonite, prehung door. Include privacy lockset and 3 butt hinges. Include casing on both sides. Include appropriate doorstop, hinge bump or base bump to match color of hinges.

NOTE: Replace trim around the doors, both sides where applicable.

83 - Replace existing receptacles with new duplex (Specification ID:1.00060 Estimated Qty:2)

Replace receptacles with color matched duplex receptacle and cover plate.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 36 of 58

84 - REPLACE LIGHT FIXTURE/ LIGHT SWITCH

Replace existing with a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and

NOTE: Install new light switch cover plates.

85 - INSTALL AN ELECTRIC SMOKE DETECTOR

(Specification ID:80.11500 Estimated Qty:1)

Install a UL listed electric hard wired smoke detector with a battery backup. Detector to have a test button, hush button and flashing LED indicator. Use materials and methods of installation that comply with electrical code requirements.

86 - REFINISH WOOD FLOOR

(Specification ID:55.04000 Estimated Qty:120)

Remove floor mounted vent and professionally refinish wood flooring. This includes removing existing floor finish, patching and sanding floor, and sealing floor with polyurethane finish per manufacturer's instructions.

87 - Register cover replacement (Specification ID:85.00000 Estimated Qty:2)

Replace missing or damaged register cover with an adjustable metal register. If return air wall register, caulk

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 37 of 58

88 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:45)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joint of shoe mold and vinyl floor covers. Use finish nails to

NOTE: Replace baseboards in the bedroom and closet area.

89 - Interior wall drywall (Specification ID:1.00000 Estimated Qty:1)

Remove existing shelving and repair hole in closet wall by removing the damaged drywall down to the stud.

Prep wall and install new 1/2" or 5/8" drywall. Apply 3/8" adhesive bead and appropriate mechanical fasteners per manufacturers specification. Set seam tape in appropriate mud bed, sand and topcoat as needed for smooth finish. Include all prep and PRIMER FINISH ready for paint.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 38 of 58

90 - PREP AND PAINT WALLS AND CEILING SURFACES

WITH SEMI-GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:1)

Apply 2 coats of semi-gloss acrylic latex paint on all walls and ceiling surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any repairs to walls and ceiling surfaces prior to painting.

NOTE: Paint bedroom and closet area.

Subtotal for Walls and Ceilings

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 39 of 58

91 - WINDOW--VINYL--LOW E SINGLE HNG DBL GLZ

ENERGY STAR - W/TRIM

(Specification ID:50.01500 Estimated Qty:2)

Field measure, order, and install two (2) PVC, 1 over 1, single hung, double glazed, argon filled Low E window that meets the ENERGY STAR standards for this climate for U value and SHGC. Include 1/2 screen. Wrap exterior jamb and sill with .027" aluminum coil stock back caulked and nailed 6" on center.

Retrim opening with casing or shoe/door.

NOTE: Re-trim around new windows.

Location: Second Floor Stair

92 - REFINISH WOOD STEPS

(Specification ID:55.04000 Estimated Qty:96)

Professionally refinish wood flooring. This includes removing existing floor finish, patching and sanding

NOTE: Include stringer and risers.

93 - INSTALL NEW STAIRCASE HANDRAIL FASTENED TO

WALL

(Specification ID:55.05000 Estimated Qty:16)

Install a new stain grade staircase handrail fastened securely to the wall by anchors spaced no more than 4 feet apart. Apply 2 coats of semi-gloss acrylic latex paint or 2 coats of stain to handrail. Genesee County staff to select type and color of finish.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 40 of 58

94 - PAINT WALLS AND TRIM WITH SEMI-GLOSS PAINT

(Specification ID:60.13750 Estimated Qty:1)

Apply 2 coats of semi-gloss acrylic latex paint to wall surfaces which includes any door casing and jambs.

Where applicable, wet scrape defective paint, spot prime, seal water stains and make any minor repairs to walls prior to painting. Genesee County staff will choose the color.

Location: Second Floor Bedroom

95 - CHEMICALLY REMOVE PAINT FROM WOOD

PANELING

(Specification ID:45.08250 Estimated Qty:1)

Chemically remove paint from wood paneling. Remove paint down to bare wood using BIX Spray-On Stripper or approved equal. Contractor to follow manufacturer's application, clean-up, disposal and worker protection instructions recommended by manufacturer. For more information about BIX Manufacturing Company, Inc. products, call 1-800-251-1098 outside Tennessee and 615-792-3260 inside Tennessee.

NOTE: Remove over sprayed paint from wood paneling and trim.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 41 of 58

96 - Replace existing receptacles with new duplex (Specification ID:1.00060 Estimated Qty:4)

Replace receptacles with colored matched duplex receptacles and cover plates.

97 - REPLACE LIGHT FIXTURE AND SWITCH

(Specification ID:80.00500 Estimated Qty:2)

Replace existing with a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $30 allowance for fixture. Include LED bulbs. Replace light fixture switch and matching cover plate

98 - REPLACE LIGHT FIXTURE AND SWITCH

Replace existing with a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $30 allowance for fixture. Replace light fixture switch with matching cover plate.

NOTE: Install in the closet of the upstairs bedroom.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 42 of 58

99 - INSTALL A CEILING LIGHT FIXTURE, SWITCH AND

WIRING

(Specification ID:80.02250 Estimated Qty:1)

Remove improper wiring and install a new ceiling light fixture with globe, bulbs, new switch and new wiring. Materials and installation method to meet with approval of electrical inspector.

Floor Quantity Cost/Units Total

100 - REMOVE FLOOR COVERING TO SUBFLOOR

(Specification ID:1.00040 Estimated Qty:1)

Remove floor covering to subfloor, remove all staples/nails and inspect subfloor for water/mold damage.

Remove all transitions. Spot screw exposed subfloor to eliminate squeaks and loose areas.

NOTE: Remove all flooring in the upstairs bedroom and closet.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 43 of 58

101 - INSTALL NEW CARPET AND PAD OVER EXISTING

FLOORING

(Specification ID:55.02500 Estimated Qty:250)

Install new FHA approved carpet of at least 35-ounce weight and 1/2" rebond pad over existing flooring.

Splices are to be: 1) to be inconspicuous, 2) located away from the center of rooms and heavy traffic areas, and 3) not permitted in rooms having a dimension less than 12'. $11.00 per yard allowance for carpet.

Genesee County staff to select carpet color and style.

102 - Register cover replacement (Specification ID:85.10010 Estimated Qty:1)

Replace the existing register cover with a new adjustable metal register.

103 - Apply Polyurethane to wooden wall and trim (Specification ID:60.13750 Estimated Qty:1)

Apply 2 coats of clear polyurethane finish to all wooden wall surfaces and trim which includes any closet, baseboard, doors, casing, jamb, window casing, sill, stools, jambs and sashes.

104 - PAINT CEILING WITH SEMI-GLOSS PAINT

(Specification ID:60.13750 Estimated Qty:1)

Apply 2 coats of semi-gloss acrylic latex paint to ceiling. Where applicable, wet scrape defective paint, spot prime, seal water stains and make any minor repairs to walls and baseboard prior to painting. Caulk cracks in baseboard and at intersection with wall surfaces using mildew resistant caulk prior to painting.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 44 of 58

105 - Interior ceiling drywall (Specification ID:1.00010 Estimated Qty:1)

After removing the existing wall covering to the studs, install new 1/2" or 5/8" drywall. Apply 3/8" adhesive bead and appropriate mechanical fasteners per manufacturers specification. Set seam tape in appropriate mud bed, sand and topcoat as needed for smooth finish. Include all prep and PRIMER FINISH ready for paint.

NOTE: Drywall over existing ceiling.

106 - WINDOW--VINYL--LOW E SINGLE HNG DBL GLZ

ENERGY STAR - W/TRIM

(Specification ID:50.01500 Estimated Qty:2)

Field measure, order, and install two (2) PVC, 1 over 1, single hung, double glazed, argon filled Low E window that meets the ENERGY STAR standards for this climate for U value and SHGC. Include 1/2 screen. Wrap exterior jamb and sill with .027" aluminum coil stock back caulked and nailed 6" on center.

Retrim opening with casing or shoe/door stop as necessary. Paint or stain/poly any raw or primed wood to match existing trim.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 45 of 58

107 - Replace light switch and cover plate (Specification ID:0 Estimated Qty:1)

Replace light switch and matching cover plate.

Location: Basment Stair

108 - REMOVE EXISTING LANDING AND STAIR FLOOR

COVERING AND INSTALL NEW VINYL PLANK FLOORING

(Specification ID:55.02300 Estimated Qty:1)

Remove existing floor and stair covering. Install new 12-mil water resistant vinyl plank floor tiles to tread and riser substrate using manufacturer's recommended adhesive and installation instructions. Measure and install new stair nosing as appropriate.

NOTE: ONLY INSTALL VINYL PLANK FLOOR ON THE STAIRS GOING TO THE KITCHEN AND

THE LANDING AT THE BACK DOOR.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 46 of 58

109 - INSTALL NEW STAIRCASE HANDRAIL FASTENED TO

WALL

(Specification ID:55.05000 Estimated Qty:16)

Install a new stain grade staircase handrail fastened securely to the wall by anchors spaced no more than 4 feet apart. The handrail shall have a 90 degree return design at each end to prevent the accidental catching of handbags or coats when traveling past the handrail. Apply 2 coats of semi-gloss acrylic latex paint or 2 coats of stain to handrail.

NOTE: The new handrail is to extend from the kitchen landing to the basement floor.

110 - INSTALL 2"X4" STUDS - STAIRWAY GAURDS

(Specification ID:40.06000 Estimated Qty:14)

Install 2"X 4" boards at open edges of the basement stair per building code requirements. At a minimum, new boards should be properly fastened at the top of the opening and onto the stair stringer. Apply two coats of paint on all sides of the 2"X4" studs.

NOTE: APPY 1 COAT OF PRIMER AND 2 COATS OF PAINT OR STAIN.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 47 of 58

111 - REMOVE AND INSTALL NEW INTERIROR

WALL/CEILING DRYWALL

(Specification ID:1.00000 Estimated Qty:150)

Remove existing drywall to the stud. Prep wall and install new 1/2" or 5/8" drywall. Apply 3/8" adhesive bead and appropriate mechanical fasteners per manufacturers specification. Set seam tape in appropriate mud bed, sand and topcoat as needed for smooth finish. Include all prep and PRIMER FINISH ready for paint.

NOTE: DRYWALL WEST SIDE OF STAIRWELL AFTER REMOVING THE WOOD PANELING.

112 - INSTALL NEW BASEBOARD SIMILAR IN STYLE AND

DIMENSION TO ORIGINAL

(Specification ID:60.08750 Estimated Qty:4)

Install baseboard that is similar in dimension and style to baseboard found throughout room or house. Install shoe mold if finish floor is vinyl or wood. Caulk joint of shoe mold and vinyl floor covers. Use finish nails to

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 48 of 58

113 - PAINT CEILING AND WALLS SURFACE WITH SEMI-

GLOSS PAINT

(Specification ID:65.05750 Estimated Qty:1)

Properly prepare and apply 2 coats of semi-gloss acrylic latex paint on all walls and ceiling surfaces. Use stain killer and primer if necessary. Wet scrape any defective paint and make any minor repairs to ceiling surfaces prior to painting. Genesee County staff to select color.

NOTE: Repair all defective areas of plaster prior to painting the walls, columns and ceiling area.

114 - REMOVE FLOORING / PAINT BASEMENT STAIRS

(Specification ID:0 Estimated Qty:1)

Remove the flooring on the basement stairs down to the substrate. Apply two coats of porch and basement paint onto the steps.

NOTE: Use the same basement gray paint from the laundry room area.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 49 of 58

115 - REPLACE LIGHT SWITCH AND COVER PLATE

Install new light switches and matching cover plates.

Location: Basement

116 - INSTALL NEW BASEMENT LIGHT FIXTURES

(Specification ID:80.01750 Estimated Qty:6)

Remove any existing basement light fixtures. Install new basement light fixtures with bulbs. Materials and installation method to meet with approval of electrical inspector.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 50 of 58

117 - SMOKE/CO DETECTOR COMBO--BATTERY

POWERED

(Specification ID:80.11250 Estimated Qty:1)

Install a UL approved, ceiling mounted, battery powered smoke detector and carbon monoxide battery combination.

NOTE: Must have 10-year Lithium-ion battery.

118 - REMOVE FLOOR COVERING TO CONCRETE

(Specification ID:1.00040 Estimated Qty:400)

Remove floor covering to concrete. Remove all transitions.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 51 of 58

119 - REPLACE LAUNDRY TUB / FAUCET / DRAIN

(Specification ID:1.00100 Estimated Qty:1)

Remove existing laundry tub to code legal landfill. Install single bowl 24" fiberglass laundry tray to fit under faucet. Include standard 2 handle chrome laundry faucet. Include and hook up waste line. Include applicable washer hookups that shall include boiler drains and air hammers as required.

120 - GENERAL CLEAN-UP

(Specification ID:1.05000 Estimated Qty:1)

Remove all trash and debris from the basement area.

Subtotal for General Requirements

121 - REPLACE GAS FURNACE

(Specification ID:85.04250 Estimated Qty:1)

Install a new UL listed gas fired furnace having an efficiency rating of at least 97% and a BTU output that is sized to properly heat house. Furnace to have a 20-year manufacturer's warranty. Provide material necessary to connect furnace to new duct system. Install new digital programable thermostat. Install new vent system where required by code. Provide necessary electrical connections. Material and method of installation to comply with mechanical, gas and electrical code requirements.

NOTE: RUN NEW GAS LINE TO FURNACE.

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 52 of 58

122 - INSTALL A CLOTHES DRYER VENT

(Specification ID:75.12500 Estimated Qty:1)

Install a sheet metal vent pipe, flexible hose with two clasps and vent cap for a clothes dryer. Vent to run from dryer to an outside wall. Neatly finish and close openings around vent opening.

123 - INSTALL SUMP PUMP / SUMP PUMP DRAIN SYSTEM

(Specification ID:75.13000 Estimated Qty:1)

Install an electric sump pump and drain line under house. Method of installation and material to meet with plumbing and electrical inspector approval. Install sump drainage system at the rear of the home. All plumbing must comply with Michigan State Plumbing Codes.

NOTE: Install sump crock lid over sump crock hole.

Subtotal for Plumbing System

Prepared By: lparks@geneseecountymi.gov on 11/8/2024 53 of 58

Porches & Entrances Quantity Cost/Units Total

124 - PAINT CONCRETE BASEMENT FLOOR

(Specification ID:40.01600 Estimated Qty:400)

Prep the concrete floor for paint. Apply 1 coat of primer and 2 coats of indoor concrete floor paint to basement floor.

125 - PAINT WALL SURFACES AND TRIM WITH SEMI-

GLOSS PAINT

(Specification…