C Monona_LED Streetlights_ProjectManual Amended 10.2.24.pdf

City of Monona DOT STIP Project ID: 5994-02-18 MONONA

DPW PROJECT NO. 08 09 2024

Title: C Monona, LED Street Lights

Limits: Various Locations – City Limits

Project federally funded using 2023 CRP program funding.

DBE 0% or NA on this project.

Prepared by: Brad Bruun, Project Manager

CITY OF MONONA

Amended bid ad - 10/2/2024

TABLE OF CONTENTS

SECTION 1: INSTRUCTIONS TO BIDDERS, BID FORM, BID AD, NOTICE OF

BID AWARD

SECTION 2: PROJECT INFORMATION - SUMMARY, MAP, MATERIALS AND

SPECIFICATIONS

SECTION 3: WISDOT SPECIFICATIONS

SECTION 4: FEDERAL/STATE/LOCAL SPECIAL PROVISIONS

SECTION 1: INSTRUCTIONS TO

BIDDERS AND BID DOCUMENTS

INSTRUCTION TO BIDDERS

PROJECT NO. 08 09 2024

SCOPE OF WORK

The City of Monona was awarded federal funding from the US Department of Transportation Carbon Reduction Grant program in 2023. The City is planning to retrofit all local, residential streetlights on local roads or alleys in 2024. The City is contracting with Madison Gas & Electric (MG&E) for the installation of the lights and will be self-purchasing the lights through a WisDOT approved bid process on VendorNet. The lights being replaced currently are attached to wood poles owned and maintained by MG&E and lie within the City’s right-of-way. 250 high pressure sodium (HPS) streetlights are planned to be replaced with an LED equivalent specified by the City in this manual under the products l i s t and materials section. Each light must be provided by the supplier equipped with a control ready 7-wire photocell receptacle, bubble level, and a snap-on light trespass house side shield. The City is also requesting bids for 250 - 8000 Series photo controls as specified in the manual.

For this project the City requests bids by certified vendors for the procurement of the following:

- (7 Cnt.) Leotek ComfortView Neighborhood LED Street Light

- CV1-H-MV-27K-2R-GY-070-PCR7-WL-BBL-HSSCV

- 2700K LED fixture, 66W, 7220 lumen, 109 lumens/watt;

- (27 Cnt.) Leotek ComfortView Neighborhood LED Street Light

- CV1-H-MV-27K-2R-GY-035-PCR7-WL-BBL-HSSCV

- 2700K fixture, 29W, 3463 lumen, 119 lumens/watt

- (216 Cnt.) Leotek ComfortView Neighborhood LED Street Light

- CV1-H-MV-27K-2R-GY-055-PCR7-WL-BBL-HSSCV

- 2700K, 48W, 5479 lumen, 114 lumens/watt

- (250 Cnt.) TE Connectivity 8000 Series photo controls, part number 8090-VFS or as specified

The City plans to issue a bid award no later than November 19th of 2024.

http://www.monona.wi.us/linkpage.htm http://www.monona.wi.us/linkpage.htm�

All transactions shall be completed within 15 days of the effective date of the notice of bid award unless otherwise indicated here:

Or not later than December 4th, 2024, whichever date is earlier.

FEDERAL AND STATE LAW REQUIRES: 23 USC 112 (a) & (b) and 23 CFR 635.104 requires that the actual construction work shall be performed by a contract awarded as a result of competitive bidding. Exemptions may be granted if another method can be shown to be more cost effective. Wisconsin S.S. 84.06(2) and/or 66.0901. 23 USC112 d 23 CFR 635.112(f) infers that by submitting a bid that the bidder has examined and carefully prepared the bid and that the bidder has not participated in any collusive activity or restraint of trade in connection with the bid preparation.

Wisconsin SS 66.0901. 23 CFR 635.112 requires that on all Federal-Aid projects the advertisement and plans be available to the prospective bidders a minimum of three

(3) weeks prior to the opening of the bids to ensure adequate review time and encourage competition. Publication requirements and types are discussed in Section 10.12. Qualified bidders must adhere to all WisDOT and Federal regulations as referenced in Sections 3 and 4 of this bid manual as applicable.

All bids shall be submitted to Brad Bruun, Monona Public Works Program Manager via email at bbruun@ci.monona.wi.us no later than October 31, 2024, AT 1:00PM

The City of Monona reserves the right to reject any and all bids, to waive any technicalities, and accept any bid, which it deems advantageous to the City. No bid shall be withdrawn after the opening of bids without the consent of the City for a period of 30 days after the scheduled time of closing bids.

Questions:

Please contact Brad Bruun, City of Monona Project Manager bbruun@ci.monona.wi.us

(608) 222-2525 EXT. 7402

BID FORM

BASIS OF BID

Bidder will complete the Work in accordance with the Contract Documents for the following price(s):

Bidders shall fill in the total for each division.

DIVISION OF MATERIALS WITH TOTAL BID AMOUNT

MATERIALS AS SPECIFIED QUANTITY MATERIALS

COST ($ - BID

PRICE)

Leotek ComfortView Neighborhood LED Street Light CV1-H-

MV-27K-2R-GY-070-PCR7-WL-BBL-HSSCV

Leotek ComfortView Neighborhood LED Street Light CV1-H-

MV-27K-2R-GY-035-PCR7-WL-BBL-HSSCV

Leotek ComfortView Neighborhood LED Street Light CV1-H-

MV-27K-2R-GY-055-PCR7-WL-BBL-HSSCV

TE Connectivity 8000 Series - 8090-VFS photo controls 250

Total Bid Price: $

TIME OF COMPLETION

Bidder agrees that the products will be shipped and ready for final payment as follows:

Notice of Bid Award Date: November 19th, 2024

Materials Transaction Date: No later than 30 days post Notice of Bid Award Date

Final Delivery Date: Not later than 45 days after Notice of Bid Award Date

BIDDER INFORMATION

COMPANY

NAME:

STREET ADDRESS:

CITY,

STATE:

ZIP CODE:

PHONE &

EMAIL:

PRINT NAME:

SIGNATURE: __________________________________________ DATE: ___________________

mailto:bbruun@ci.monona.wi.us

08 09 2024

ADVERTISEMENT FOR BIDS FOR MONONA LED STREETLIGHT

RETROFIT MATERIALS PURCHASE

City of Monona Dane County, Wisconsin

BID OPENING: THURSDAY, October 31, 2024, AT 1:00PM – Virtually via Zoom link provided at end of this advertisement.

The City of Monona will receive bids via email to Brad Bruun, bbruun@ci.monona.wi.us at the time and date stated above, at which time, all Bids will be opened and processed virtually via the Zoom link shared at the end of this posting. Bidding documents will be posted on VendorNet.wi.gov.

This project will be bid as a materials procurement bid. Bidders will be asked to provide the following:

- (7 Cnt.) Leotek ComfortView Neighborhood LED Street Light

- CV1-H-MV-27K-2R-GY-070-PCR7-WL-BBL-HSSCV

- 2700K LED fixture, 66W, 7220 lumen, 109 lumens/watt

- (27 Cnt.) Leotek ComfortView Neighborhood LED Street Light

- CV1-H-MV-27K-2R-GY-035-PCR7-WL-BBL-HSSCV

- 2700K fixture, 29W, 3463 lumen, 119 lumens/watt

- (216 Cnt.) Leotek ComfortView Neighborhood LED Street Light

- CV1-H-MV-27K-2R-GY-055-PCR7-WL-BBL-HSSCV

- 2700K, 48W, 5479 lumen, 114 lumens/watt

- (250 Cnt.) TE Connectivity 8000 Series photo controls as specified

- 8090-VFS

A project manual with specifications and WisDOT/Federal bidding requirements is attached to this bid advertisement.

Expected Date of the Notice of Bid Award is November 19, 2024. Process of the order form and purchase agreement must be completed no less than 15 days after notice of bid award.

Bids may not be withdrawn within 30 days after the date of the bid opening. The City of Monona reserves the right to reject any or all Bids, and to award the Contract to the Bidder, who in the judgment of the Owner, will best serve the interest of the Owner.

Wisconsin S.S. 84.06(2) and/or 66.0901. 23 USC112 d 23 CFR 635.112(f) regulations apply to this bid and by submitting a bid for this project the bidder confirms they have examined and carefully prepared the bid and that the b i d d e r has not participated in any collusive activity or restraint of trade in connection with the bid preparation. Wisconsin SS 66.0901.

23 CFR 635.112 requires that on all Published by the authority of the City of Monona via VendorNet.gov and is to be published in the Wisconsin State Journal on October 17th and 24th of 2024.

Contact Info for Questions:

Brad Bruun - City of Monona Project Manager bbruun@ci.monona.wi.us

(608) 222-2525 ext. 7402

City of Monona is inviting you to a scheduled Zoom meeting.

Join Zoom Meeting https://us02web.zoom.us/j/87275139462

Meeting ID: 872 7513 9462

One tap mobile +13017158592,,87275139462# US (Washington DC) 13052241968,,87275139462#

+US

Dial by your location

• +1 301 715 8592 US (Washington DC)

• +1 305 224 1968 US

• +1 309 205 3325 US

• +1 312 626 6799 US (Chicago)

• +1 646 558 8656 US (New York)

• +1 646 931 3860 US

• +1 564 217 2000 US

• +1 669 444 9171 US

• +1 669 900 9128 US (San Jose)

• +1 689 278 1000 US

• +1 719 359 4580 US

• +1 253 205 0468 US

• +1 253 215 8782 US (Tacoma)

• +1 346 248 7799 US (Houston)

• +1 360 209 5623 US

• +1 386 347 5053 US

• +1 507 473 4847 US

Meeting ID: 872 7513 9462

Find your local number: https://us02web.zoom.us/u/kLRKLWr36

PROJECT N0. 08 09 2024

TO:

(BIDDER)

DATE:

MONONA DPW PROJECT NO.: 08 09 2024

PROJECT TITLE: C Monona, LED Street Lights

To whom this may concern:

You are notified that the bid your company submitted for the above-named project has been approved by the City of Monona. The processing of the order therein must be completed with notification of shipment to the City no later than 15 business days after the above-listed date.

(OWNER – PRINT NAME)

(OWNER AUTHORIZED SIGNATURE)

(OWNER TITLE)

NOTICE OF BID AWARD

SECTION 2: PROJECT

INFORMATION -

SUMMARY, MAP, MATERIALS

AND SPECIFICATIONS

Executive Summary

The City of Monona was awarded federal funding from the US Department of Transportation - Carbon Reduction Grant program in 2023. The City is planning to retrofit all local, residential streetlights on local roads or alleys in 2024. The City is contracting with Madison Gas & Electric (MG&E) for the installation of the lights and will be self-purchasing the lights through a WisDOT approved bid process on VendorNet. The lights being replaced currently are attached to wood poles owned and maintained by MG&E and lie within the City’s right-of-way. 250 high pressure sodium (HPS) streetlights are planned to be replaced with an LED equivalent specified by the City in this manual under the products list and materials section. Each light must be provided by the supplier equipped with a control ready 7-wire photocell receptacle, bubble level, and a snap-on light trespass house side shield. The City is also request bids for 250 - 8000 Series photo controls as specified in the manual.

Esri, NASA, NGA, USGS, FEMA, Sources: Esri, USGS, County of Dane, Esri, HERE, Garmin, SafeGraph, GeoTechnologies, Inc, METI/NASA, USGS, EPA, NPS, US Census Bureau, USDA

0.5

Miles

Legend

2023 Residential Streetlight Conversion Monona City Limits

Date Exported: 4/7/2023 10:30 AM

©2020 Leotek Electronics USA.

ComfortView_Series_Specification Sheet_01-27-20.

Specifications subject to change without notice.

Product LED Code Voltage Color Temperature Distribution Finish1 Output Code2 Options

CV1 H MV

HV

120-277V 347-480V

27K 30K 40K

2700K 3000K 4000K

2R 3R

Type 2 Type 3

GY

DB

BK

Gray Dark Bronze Black

FOC3

LPCR

PCR74

PCR7-CR5

WL

4B

RWG

SWTB

BBL

CF6

Fixed Output Code Less Photocontrol Receptacle ANSI 7-wire Photo-control Receptacle Control Ready 7-wire PC Receptacle Utility Wattage Label 4-Bolt Mounting Bracket Rubber Wildlife Guard Straight Wire Terminal Block Bubble Level Coastal Paint Finish

Accessories*

CSSCV7

FSSCV8

HSSCV9

VHCS10

PTB11

PTB211

RPB11

SPB11

WB11

LLPC12

SC

BSK

Cul-De-Sac Side Shield, Snap-On* Front Side Shield, Snap-On* House Side Shield, Snap-On* 80 Degree Cutoff Shield*

Pole Top Tenon Horizontal Arm Bracket Pole Top Tenon Horizontal Arm Bracket (2@180o) Round Pole Horizontal Arm Bracket Square Pole Horizontal Arm Bracket Wall Horizontal Arm Bracket

Long-Life Twist Lock Photocontrol Twist Lock Shorting Cap

Bird Deterrent Spider Kit

Notes:

1 Gray, Black, and Dark Bronze standard. Consult factory for other finishes.

2 Specified output code is the factory set lumen performance. Field adjustable is standard via an eight-position output selector. Refer to output data table on this spec sheet. An illustration of the output selector and its label is shown on page 2. Consult factory if special output setting is required.

3 Non-field adjustable, fixed lumen output. Specify required output code. Not available with PCR7-CR option.

4 Includes output selector that enables field adjustability of light levels. Includes connectors to allow easy upgrade of wireless dimming via PCR7. Wireless node by others.

5 Control-ready wired at factory for wireless none dimming (node by others). Output selector not included in the fixture. Not able to adjust above specificed drive current.

6 Specify the CF Option for coastal installation. See warranty for details.

7 Flush mounted Cul-de-Sac Shield cuts light off at 1 times the mounting height behind the luminaire, 1¾ in front, and 2¼ times the mounting height laterally.

8 Flush mounted Front Side Shield cuts light off at approximately 1½ times the mounting height in front of the luminaire (street side) and 2¼ times the mounting height laterally.

9 Flush mounted House Side Shield cuts light off at 1 times the mounting height behind the luminaire and 2¾ times the mounting height laterally.

10 80 Degree Cutoff Shield mitigates high angle glare above 80 degrees from nadir and cuts light off at 1½ times the mounting height behind and 2⅓ times the mounting height laterally.

11 Specify Color (GY, DB, BK) 12 Specify MV (120-277V) or HV (347-480V).

*Accessories are ordered separately and not to be included in the catalog number.

For factory installed HSSCV, CSSCV, FSSCV and VHCS specify as option in luminaire catalog number. HSSCV, CSSCV, FSSCV can be installed without a tool, but a tool is required for removal. 80 Degree Cutoff Shield (VHCS) requires a Phillips head screwdriver for installation.

Ordering Information Sample Catalog No. CV1-H-MV-40K-2R-GY-045-FOC

Luminaire Data

Project

Type

Catalog No.

ComfortView™ Neighborhood LED Street Light CV Specification Data Sheet

9.

in [2 m m

18.35 in [466 mm]

4.

in [1 m m

4.

in [1 m m

9.55 in [243 mm]

4.

in [1 m m

9.

in [2 m m

18.35 in [466 mm]

9.

in [2 m m

18.35 in [466 mm]

4.

in [1 m m

4.

in [1 m m

9.55 in [243 mm]

4.

in [1 m m

*2700 and 3000K ComfortView fixtures are certified as Community Friendly Lighting Equipment by the Smart Outdoor Lighting Alliance (SOLA).

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

BBruun Highlight

Specifications subject to change without notice.

Luminaire Specifications

Housing Die cast aluminum housing with universal two-bolt slip fitter mounts to 1-1/4” to 2” (1-5/8” to 2-3/8” O.D.) diameter mast arm.

One-piece aluminum housing provides passive heat-sinking of the LEDs and has upper surfaces that shed precipitation. Four-bolt mounting bracket is available. Mounting provisions meet 3G vibration per ANSI C136.31-2010 Normal Application, Bridge & Overpass. Mounting has leveling adjustment from ± 5° in 2.5° steps.

Electrical components are accessed without tools via a high-strength, non-conductive polycarbonate door with quick-release latches.

Polycarbonate material meets UL 746C for outdoor usage. Available rubber wildlife guard (RWG option) conforms to mast arm with no gaps.

Light Emitting Diodes Hi-flux/Hi-power white LEDs produce a minimum of 90% of initial intensity at 100,000 hours of life based on IES TM-21 (L90 ≥ 100k hours). LEDs are tested in accordance with IES LM-80 testing procedures. LEDS have correlated color temperature of 2700 (27K), 3000 (30K), 4000 (40K), and 70 CRI minimum. LEDs are 100% mercury and lead free.

Field Adjustability LED lumen output can be changed in the field to adjust light output for local conditions (not available with PCR7-CR option). The specified output code will be the factory set output.

Field adjustments can be made with the output selector included in the fixture. Field adjustable range shown in performance data table.

Quality Control Every luminaire is performance tested before and after a 2-hour burn-in period. Assembled in the USA.

Optical Systems Two-stage reflective optics produce IESNA Type 2 or Type 3 distributions and are fully sealed to maintain an IP66 rating. Luminaire produces 0% total lumens above 90⁰ (BUG Rating, U=0).

Optional house side shield cuts light off at 1/2 mounting height behind luminaire. Cul-de-sac shield provides back and side light control for end of cul-de-sac applications. Front side shield cuts light off at approximately one mounting height in front of luminaire (street side). 80 degreee cutoff shield eliminates very high angle glare above 80 degrees from nadir. All shields are field installable without tools.

Electrical Rated life of electrical components is 100,000 hours. Uses isolated power supply that is 1-10V dimmable. Power supply is wired with quick-disconnect terminals. Power supply features a minimum power factor of .90 and <20% Total Harmonic Distortion (THD). EMC meets or exceeds FCC CFR Part 15. Terminal block accommodates 6 to 14 gauge wire. Surge protection complies with IEEE/ANSI C62.41 Category C High, 20kV/10kA and ANSI C136.2- 2015, 20kV/10kA.

Controls 3-Wire photocontrol receptacle is standard.

ANSI C136.41 7-wire (PCR7) photocontrol receptacles is available. All photocontrol receptacles have a tool-less rotatable base.

Wireless control module is provided by others.

Finish Housing receives a durable, fade-resistant polyester powder coat finish with 3.0 mil nominal thickness. Standard finish tested to withstand 5000 hours in salt spray exposure per ASTM B117 and Coastal Finish per ASTM G85.

Finish meets scribe creepage rating 8 per ASTM D1654. Finish tested 500 hours in UV exposure per ASTM G154 and meets ASTM D523 gloss retention.

Listings/Ratings/Labels Luminaires are UL listed for use in wet locations in the United States and Canada. DesignLights Consortium™ qualified product. Consult DLC QPL for Standard and Premium Classification Listings. International Dark Sky Association listed. 2700 and 3000K ComfortView fixtures are certified as Community Friendly Lighting Equipment by the Smart Outdoor Lighting Alliance (SOLA). Luminaire is qualified to operate at ambient temperatures of -40°C to 40°C.

Photometry Luminaires photometrics are tested by certified independent testing laboratories in accordance with IES LM-79 testing procedures.

Warranty 10-year limited warranty is standard on luminaire and components.

Vandal Resistance Housing and optics rated to IK10

Standards Luminaire complies with:

ANSI: C136.2, C136.3, C136.10, C136.13,

C136.15, C136.22, C136.31, C136.35, C136.37, C136.41, C62.41, C78.377, C82.77 Other: FCC 47 CFR, IEC 60598, ROHS II, UL 1449, UL 1598Example of ComfortView™ Output Selector and Label:

W Est lm 1 : 66 / 7000 2 : 48 / 5500 3 : 43 / 5000 4 : 38 / 4500 5 : 34 / 4000 6 : 29 / 3500 7 : 24 / 3000 8 : 19 / 2500

ComfortView™ Neighborhood LED Street Light CV Specification Data Sheet

Specifications subject to change without notice.

Product Color

Temperature

(CCT)

Output Code Drive Current (mA)

System Wattage (W)

Delivered Lumens (Lm)2

Efficacy (Lm/W)

Field Adjustable Output Range

CV1-H

2700K (27K)

025 190 19 2242 118

030 250 24 2892 120

035 300 29 3463 119

040 350 34 4163 122

045 400 38 4535 119

050 460 43 4998 116

055 520 48 5479 114

070 700 66 7220 110

3000K (30K)

025 190 19 2412 127

030 250 24 3073 128

035 300 29 3676 127

045 350 35 4423 128

050 400 38 4777 126

055 460 45 5561 124

060 520 49 5800 118

075 700 67 7722 115

4000K (40K)

025 190 19 2675 139

035 250 24 3294 137

040 300 29 3930 136

045 350 34 4561 134

050 400 38 5059 133

055 460 43 5594 130

060 520 48 6147 128

080 700 67 8227 123

Performance Data1

All data nominal. IES files for all CCTs available at leotek.com.

ComfortView™ Neighborhood LED Street Light CV Specification Data Sheet

Notes:

1 Data shown above is for type 2 optic. For type 3 optic, consult IES files for specific data at Leotek.com 2 Nominal lumens. Normal tolerance ± 10% due to factors including LED bin variance, and ambient temperatures.

Specifications subject to change without notice.

Type 2 Type 3

Product Color

Temperature

(CCT)

Output Code Drive Current (mA) BUG Rating BUG Rating

CV1-H

2700K (27K)

025 190 B1-U0-G1 B1-U0-G1

030 250 B1-U0-G1 B1-U0-G1

035 300 B1-U0-G1 B1-U0-G1

040 350 B1-U0-G1 B1-U0-G1

045 400 B1-U0-G1 B2-U0-G1

050 460 B1-U0-G1 B2-U0-G1

055 520 B1-U0-G1 B2-U0-G1

070 700 B2-U0-G1 B2-U0-G2

3000K (30K)

025 190 B1-U0-G1 B1-U0-G1

030 250 B1-U0-G1 B1-U0-G1

035 300 B1-U0-G1 B1-U0-G1

045 350 B1-U0-G1 B1-U0-G1

050 400 B1-U0-G1 B2-U0-G1

055 460 B1-U0-G1 B1-U0-G1

060 520 B1-U0-G1 B2-U0-G1

075 700 B2-U0-G1 B2-U0-G2

4000K (40K)

025 190 B1-U0-G1 B1-U0-G1

035 250 B1-U0-G1 B1-U0-G1

040 300 B1-U0-G1 B1-U0-G1

045 350 B1-U0-G1 B2-U0-G1

050 400 B1-U0-G1 B2-U0-G1

055 460 B1-U0-G1 B2-U0-G1

060 520 B2-U0-G1 B2-U0-G1

080 700 B2-U0-G1 B3-U0-G2

BUG Ratings All data nominal. IES files for all CCTs available at leotek.com.

ComfortView™ Neighborhood LED Street Light CV Specification Data Sheet

ComfortView™ light trespass shields provide a range of options for controlling light distribution at the source and can be easily installed at the factory or in the field.

Exclusive Snap-On Light Trespass Shields for ComfortView™ LED Street Lights

©2019 Leotek Electronics USA. ComfortView Light Shield Info-Installation Sheet_04-01-19.

Specifications subject to change without notice.

Front Side Shield

80o Cutoff Shield

House Side Shield

Unshielded Street Light

Cul-de-Sac Side Shield

80o 80o

Front Side Shield

80o Cutoff Shield

House Side Shield

Unshielded Street Light

Cul-de-Sac Side Shield

80o 80o

Flush mounted House Side Shield cuts light off at 1 times the mounting height behind the luminaire and 2¾ times the mounting height laterally.

Flush mounted Front Side Shield cuts light off at approximately 1½ times the mounting height in front of the luminaire (street side) and 2¼ times the mounting height laterally.

House Side Shield (HSSCV)

Front Side Shield (FSSCV)

Front Side Shield

80o Cutoff Shield

House Side Shield

Unshielded Street Light

Cul-de-Sac Side Shield

80o 80o

80 Degree Cutoff Shield mitigates high angle glare above 80 degrees from nadir and cuts light off at 1½ times the mounting height behind and 2⅓ times the mounting height laterally.

80 Degree Cutoff Shield (VHCS)

Front Side Shield

80o Cutoff Shield

House Side Shield

Unshielded Street Light

Cul-de-Sac Side Shield

80o 80o

Cul-de-Sac Shield (CSSCV) Flush mounted Cul-de-Sac Shield cuts light off at 1 times the mounting height behind the luminaire, 1¾ in front, and 2¼ times the mounting height laterally.

Place the shield so that the slots align with the clips along the edge of the ComfortView Light Engine, then simply push the edges of the shield down to clip it into place.

Each shield, regardless of type, has slots for securing the clips along both edges of the ComfortView light engine cover.

Align the slots with the corresponding clips along the edges of the ComfortView Light Engine.

ComfortView™ Snap-On Light Trespass Shield Installation

Leotek’s HSSCV, CSSCV, and FSSCV Light Trespass Shields for ComfortView allow for easy snap-on installation in the field.

Clip Slots

Clips

Clips

Captive screws are attached to each corner of the 80 Degree Cutoff Shield to align with the threaded holes in the fixture’s housing. Place the shield on the underside of the light fixture as shown and firmly tighten the screws.

The 80 Degree Cutoff Shield has mounting holes in all four corners that correspond with threaded holes in the housing.

Mounting screws are provided with the shield.

Align the holes in the shield with the corresponding holes along the edges of the ComfortView Light Engine.

ComfortView™ 80 Degree Cutoff Trespass Shield Installation

Leotek’s 80 Degree Cutoff Light Trespass Shield (VHCS) for ComfortView is easily installed with a screw in each corner.

Screw Holes

Threaded Holes in ComfortView Housing

ENERGY /// STREET LIGHTING PHOTOCONTROLS

STREET LIGHTING

PHOTOCONTROLS

A COMPREHENSIVE

PORTFOLIO FOR STREET

LIGHTING APPLICATIONS

For more than 50 years, TE Connectivity (TE) and its well-known ALR product line have supported utilities, city authorities and contractors with safe and reliable connection boxes and accessories for lighting poles for a variety of street lighting applications including:

• Public street lighting

• Private outdoor lights for parking lots and apartment buildings

• Industrial settings such as refineries and power plants

• Infrastructure, including harbours, airports and rail stations

Place photo here

SPECIFICATION - DIMENSIONS IN MM

Physical

Dimensions: approx. 83mm dia. x 45mm high (not including contacts)

Enclosure: designed to meet ANSI C136.10

Power consumption: less than 0.5 watts at 120 VAC

Temperature Minus 40°C to plus 65°C at 96% RH

Control DC Electromagnetic switch type exceeds 20,000 ON/OFF operations per ANSI C136.10

Relay Rating 30 Amp General Purpose Relay

Load Rating 1000 Watt Tungsten 1800 VA

Light Sensor Non-drifting Phototransistor

Cover High impact polypropylene with UV stabilised polycarbonate window

Base High temperature polyester (PBT)

Gasket Cross-linked polyethylene

Connection 3-pole locking-type with solid brass legs

ENERGY /// STREET LIGHTING PHOTOCONTROLS

8000 SERIES PHOTOCONTROL

ELECTRONIC, ULTRA LONG LIFE,

HIGH PERFORMANCE

TE Connectivity’s (TE) advanced technology 8000 Series Photocontrol provides a unique, durable, and multi-volt control especially designed for twenty year operation.

Aluminium electrolytic capacitors have a rated lifetime of only 5000 hours at 105°C. TE has eliminated electrolytic capacitors in the 8000 series, resulting in a truly long life control. Double-sided, plated-through, glass epoxy FR4 circuit board along with a 30 Amp rated at 120VAC relay ensures that our control will surpass 20,000 ON/OFF operation cycles per ANSI C136.10.

Like all of TE’s electronic controls, the 8000 Series utilises our inter-locking base/cap design for excellent environmental housing. High temperature base material, rated at a minimum 138°C, along with a UV stabilised, opaque housing ensure our control will last over 20 years without degradation.

TE uses a process of IR filtering a phototransistor which in turn gives a human eye response along with long-term, drift free light sensing for the life of the control.

KEY FEATURES

• Multi-volt operation

• High-temperature housing and components

• 25 mm, 20 kA, 300 Joule MOV Standard

• Meets or exceeds ANSI C136.10

TECHNICAL INFORMATION

Rated Volts 105 – 305 VAC

Frequency 50/60 Hz

Operating Light Levels Standard 1.5 Fc ON (optional 1 - 3 Fc)

Time Delay ON/OFF Instant ON, 2 - 5 second delay OFF

OFF/ON Ratio 1.5 : 1

Fail Mode ON or OFF

Surge Protection 25 mm, 20 kA, 300 Joules MOV

Rated Life 20 years

83mm

5m m

ANSI Standard Fail Fail

Cap Colours ON OFF

120V Grey Orange

208/240/277V Maroon -

120/208/240/277V Blue Green

HOW TO SPECIFY

Series (Fail Mode)

8 = 8000 (ON)

OFF/ON Ratio 0 = 1.5 : 1

Voltage 90 = 120/208/240/277

MOV Surge Protection V = 300J, 510V, 20,000A, 25mm

Light Sensor F = IR Filtered Phototransistor

Cap Color (Leave blank if ANSI Standard) BL = Blue BK = Black BR = Brown (Bronze) GN = Green GR = Gray MR = Maroon YL = Yellow OR = Orange

Fail OFF Option FO = Fail OFF Option (leave blank if Fail ON)

Turn-On Level 1 = 1.0 Fc S = 1.5 Fc (ANSI Std) 2 = 2.0 Fc 3 = 2.6 Fc

8 0 90 - V F S - _ _ - _ _

The 8000 series offers almost unlimited options ensuring your lighting network needs will be met.

Place photo here

Physical

Dimensions: 27.23mm dia. x 64.88mm high ( including contacts)

Enclosure: UV stabilised

Polypropylene Cover and Hi-Temperature Polyester (PBT) Base

Temperature Power consumption: less than 0.5 watt

Control Minus 40°C to plus 65°C @ 96% RH

Relay Rating Intelligent electromagnetic switch exceeds 20,000 ON/OFF operations 16A

Load Rating 700 Watt Tungsten, 700 VA Ballast

Light Sensor Non-Drifting Phototransistor

ENERGY /// STREET LIGHTING PHOTOCONTROLS

D2 SERIES PHOTOCONTROL

EXTENDED LIFE

TE Connectivity’s advanced technology Extended Life D2 Series Photocontrol provides a unique mix of low-cost, long-life, and small form factor for demanding Roadway and Specialty Lighting applications.

TE has developed a new EL (Extended Life) - series as part of the D2 offering, providing greater benefits and improved performance over the original model.

It utilises advances in ultra-low power microcontroller technology to halve power consumption from our original model while increasing load switching capability (including loads with phase correction capacitors). It also incorporates a 320J MOV for enhanced protection of the luminaire from line transients. This level of protection has only previously been available in the larger NEMA photo cells.

The new D2 photo cell improves on the performance of the original model by incorporating a heavy-duty relay manufactured by TE. This relay is assisted by a triac that eliminates contact welding when driving large luminaires with PFC capacitors. The triac conducts at the line zero-crossing point during lamp turn-on, charging any load capacitance before the relay contacts close. This also reduces sags and surges on the network caused by the luminaire switching.

KEY FEATURES

• Premium utility grade control

• High reliability, long life

• High-temp housing and components

• 320 Joule MOV standard

• Extremely reliable versatile design applications

Rated Volts 185 – 305 VAC

Frequency 50 Hz

Operating Light Levels Standard 10 lux ON (Optional 10-35 lux)

Time Delay ON/OFF Instant ON 2-5 Second Delay OFF

OFF/ON Ratio 1.5 : 1 2 : 1 0.6 : 1 (Inverse Ratio)

Fail Mode ON

Surge Protection 320 Joules

Rated Life 20 years

*For Customer Defined Delay, there is a 60 second test mode on start up where it will be Instant ON/OFF. Once test mode is complete, the unit will function according to the specified ON/ OFF Time Delays. This will assist field staff in testing the functionality during installation.

64.88mm

27.23mm

HOW TO SPECIFY

The D2 Series provides many options ensuring your lighting network needs will be met.

SERIES (FAIL MODE)

D2 = D2 (ON)

MARKET

A = ANZ

J = Japan

CIRCUIT CONFIGURATION

E = Extended Life

D2 A - E 2 2 I

ON TIME DELAY

I = Instant

F = 2.5 Seconds

T = Customer Defined Delay*

OFF/ON RATIO

1 = 1.5:1

2 = 2:1

3 = 0.6:1

TURN-ON LIGHT LEVEL

1 = 10 lux

2 = 15 lux

3 = 20 lux

4 = 25 lux

5 = 30 lux

6 = 35 lux

SHORTING AND OPEN CAPS

DURABLE, WEATHERPROOF, LONG LASTING

TE Connectivity (TE) offers durable weatherproof shorting and open caps. Common uses include designating fixtures for maintenance, keeping lights continually on for safety (shorting cap), or disconnecting service when lighting is no longer needed (open cap).

SC, MC and NS caps provide a convenient and economical method to close or open the primary circuit with a NEMA locking type receptacle. The MC-10 model also incorporates a 545 Joule Metal Oxide Varistor (MOV) that protects the cap and the luminaire from transient line surges.

Designating ANSI in the part number will provide a unit with a stepped housing dictated in the ANSI C136.10 specification. This unique housing makes it easier for users to distinguish visually between a standard photocontrol and a shorting or open cap.

Shorting and non-shorting models are available as well as optional surge protection (545 Joule).

THE SC, MC & NS SERIES ARE THE RESULT

OF OVER FIFTY YEARS OF EXPERIENCE

DESIGNING AND DELIVERING SUPERIOR

PHOTOCONTROLS AND OTHER LIGHTING

ACCESSORIES AROUND THE WORLD.

DESIGNATE FIXTURES

INOPERABLE OR FOR

MAINTENANCE

PRODUCT SELECTION INFORMATION

Description Circuit Type Cap Colour Load Rating

Tungsten (Watts)

Load Rating Ballast (VA)

Surge Protection (Joules)

SC-10A* Shorting Clear 1000 1800 —

SC-10ANSI** Shorting Black 1000 1800 —

MC-10ANSI** Shorting Black 1000 1800 545

NS-10ANSI** Open Red 1000 1800 —

SPECIFICATION - DIMENSIONS IN MM

Physical

SC - 10A

Dimensions: approx. 73mm dia x 41mm high (excluding contacts)

SC - 10 ANSI,

MC - 10 ANSI, NS - 10 ANSI:

Dimensions: approx. 73mm dia. x 35.56mm high (excluding contacts)

Temperature Minus 40°C to plus 65°C at 96% RH

Cover High impact polypropylene (ANSI Series)

High impact UV stabilised polycarbonate (SC - 10A Series)

Base High temperature polyester (PBT)

Gasket Cross-linked polyethylene

Connection 3-pole locking-type with solid brass legs

50.8

ANSI Series (mm)

30.5

35.6 22.9

15.24

SC - 10A Series (mm)

* UL Listed

** ANSI C136.10-2006 Compliant

E66375

LC SERIES PHOTOCONTROL

THERMAL, LOCKING STYLE, RESIDENTIAL GRADE

TE Connectivity’s (TE) LC Series offers a locking style control ideal for residential lighting applications. The LC Series locking-type photocontrol offers an economical and cost-effective means of controlling residential lighting systems from dusk to dawn.

A heavy-duty thermal bi-metal switch that produces a minimum 30 - 45 second time delay, virtually eliminating unwanted OFF/ON operations that could result from lightning, car headlights or other sudden changes in the ambient outdoor light level.

LC controls are a perfect and reliable solution for lighting driveways, patios, decks, entryways or other areas around the home where security lighting is desired

THE LC SERIES IS THE RESULT OF OVER FIFTY YEARS

OF EXPERIENCE DESIGNING AND DELIVERING

SUPERIOR PHOTOCONTROLS AND OTHER

LIGHTING ACCESSORIES AROUND THE WORLD.

HEAVY-DUTY THERMAL

BI-METAL SWITCH

ALR-LC-208-277

74mm m m

ALR-LC-120

73mm

1m m

Rated Volts 105 - 305 VAC

Frequency 50 - 60 Hz

Operating Light Levels Standard 1.5 Fc ON

Time Delay 30 - 45 Second Delay ON and OFF

OFF/ON Ratio 4 : 1

Fail Mode ON

Rated Life 4 years

PRODUCT SELECTION INFORMATION

Description Rated Volts Range (Volts)

Rating Tungsten (Watts)

Rating Ballast (VA)

Turn ON (Fc)

OFF/ON

Ratio POP Pkg.

LC-120 120 105 - 130 1000 1800 1.5 4 : 1 Yes

LC-208-277 208/240/277 185 - 305 1000 1800 1.5 4 : 1 Yes

LR27428E66375

SPECIFICATION - DIMENSIONS IN MM

Physical

Dimensions: approx. 73mm dia x 41mm high (LC-120)

Enclosure: designed to meet ANSI C136.10

Power consumption: less than

0.9 watts (avg.) at 120 VAC

Temperature Minus 40°C to plus 65°C at 96% RH

Switch SPST thermal bi-metallic Exceeds 7500 ON/OFF operations at rated load

Load Rating 1000 Watt Tungsten 1800 VA ballast

Cover High impact Noryl with UV stabilised acrylic window

Base High temperature polyester (PBT)

Gasket Cross-linked polyethylene

Connection 3-pole locking-type with solid brass legs

Light Sensor 1/2” Cadmium Sulfide (Cds) Cell

PRODUCT SELECTION INFORMATION

Description Range (Volts)

Load Rating Ballast

(VA)

Load Rating Ballast (Amps)

Flange Diameter

Receptacle Barrel

Diameter

Overall Height

Lead Wire

Length

Bracket (inches) Depth

Height Width

AM-1-A 120 - 480 1800 15.0 2-9/16 1-3/8 1-1/2 9 2.0 3 5-1/2

AM-1-A-NB 120 - 480 1800 15.0 2-9/16 1-3/8 1-1/2 9 – – –

AM-2-A 120 - 480 1800 15.0 2-9/16 – 3-1/4 6 2.0 3 5-1/2

AM-2-A-NB 120 - 480 1800 15.0 2-9/16 – 3-1/4 6 – – –

ENERGY /// STREET LIGHTING PHOTOCONTROLS

Place photo here

SPECIFICATION - DIMENSIONS IN MM

Physical Dimensions: approx. 65.02mm x 36.58mm high (not including wires)

Designed to meet ANSI C136.10

Nipple "1/2” - 14NPSL as per ANSI/ASME B1.20.1 (AM-2A and AM-2-A-NB)"

Housing Aluminium Casting (AM-2-A and AM-2-A-NB)

Bracket Aluminium

Lead Wires #14 AWG, rated 105°C

AM SERIES RECEPTACLES

LOCKING TYPE, WEATHERPROOF, LONG LASTING

TE Connectivity (TE) offers a long life and weatherproof locking style receptacle. The AM Series is designed specifically for street, roadway and outdoor lighting applications.

This 3-pole, 3-wire locking type receptacle conforms to the ANSI, NEMA, and UL standards for lighting receptacles. The AM-1-A and AM-2-A includes mounting brackets.

Common uses for the AM Series Receptacles include roadway, park, and parking lighting.

KEY FEATURES

• Phosphor bronze contacts

• Thermal-set phenolic base

• UL recognised component

• Extremely reliable and versatile

• Meets ANSI C136.10

AM-1-A Series

Figure A: Side profile

Figure B: Top View

AM-2-A Series

Includes AM-1-A Series Figure above along with the Aluminium lower housing

Figure C: Side profile

Figure D: Top View

Fig. A Fig. B

E168962

Fig. C Fig. D

E168962

E168962

Physical

Dimensions: approx. 51.94mm dia. x 41.21mm high (Not including wiring)"

Enclosure: designed to meet ANSI C136.24, UL 773A

Power consumption: less than

0.9 watts at 120 VAC

Temperature Minus 40°C to plus 65°C at 96% RH

Control Thermal State Switch Type

Light Sensor Cadmium Sulfide Cell

Place photo here

AA SERIES PHOTOCONTROL

THERMAL, BUTTON STYLE, WIRE - IN DESIGN

TE Connectivity’s (TE) AA Series offers a unique button style design for internal post fixtures or mounting applications. Common uses include decorative light fixtures, post lanterns, wall mount applications, and other commercial and residential uses.

TE’s innovative design with the wire leads exiting from the rear allow the control to be placed in tight locations while positioning the wiring for easy access.

The AA Series photocontrol is constructed of a high impact UV stabilised polycarbonate housing for superior quality. The 105W and 1068W controls include a brushed aluminium wall plate for installation in standard outlet boxes.

The 105M and 1068M are equipped with a 180 Joule Metal Oxide Varistor (MOV) and are designed to protect luminaries where transient voltage surges are a frequent and recurring problem.

The 105HA is a high ambient temperature photocontrol, designed specifically to last longer in today’s hotter running HID luminaries. This unit incorporates insulation and heat sink to absorb the heat generated by the lamp and other components, significantly adding to the control’s useful life.

KEY FEATURES

• 3/4in long threaded nipple

• 30 – 45 second time delay

• UL and CSA Listed

• Durable polycarbonate housing

• 1800 and 1200 watt load rating

• Fail mode is ON

Switch SPST thermal bi-metallic, exceeds 7,500 ON/OFF operations

Fail Mode ON (contacts normally closed)

Housing Polycarbonate with UV stabilised window

Lead Wires 6”, #18 AWG, rated 105°C (AA controls) 15”, #18 AWG, rated 105°C (AA-M controls) 6”, #18 AWG, rated 150°C (AA-HA controls)

Nipple 3/8” pipe

Nut 3/8” pipe, thermoplastic

Light Sensor 1/2” Cadmium sulfide (Cds) cell

PRODUCT SELECTION INFORMATION

Description Product Information Rated Volts Range

(Volts)

Load Rating

Tungsten (Watts)

Load Rating

Ballast (VA)

Surge Protection (Joules)

Turn ON (Fc)

OFF/ON

Ratio

AA-105 120 105 - 130 1800 1100 1.5 4 : 1

AA-105W w/Wall Plate 120 105 - 130 1800 1100 1.5 4 : 1

AA-1068 208/240/277 185 - 305 1200 1100 1.5 4 : 1

AA-1068W w/Wall Plate 208/240/277 185 - 305 1200 1100 1.5 4 : 1

AA-305 120 105 - 130 300 840 1.5 4 : 1

AA-105M 15" Leads 120 105 - 130 1800 1100 180 1.5 4 : 1

AA-1068M 15" Leads 208/240/277 185 - 305 1200 1100 180 1.5 4 : 1

AA-105HA High Ambient 120 105 - 130 1800 1100 1.5 4 : 1

R. SIDE VIEWTOP VIEW

E45412 LR27428

Dimensions shown in mm

14.51 28.91

16.53

41.21

25.97 28.96

20.63

R. SIDE VIEWTOP VIEW

E45412 LR27428

Dimensions shown in mm

14.51 28.91

16.53

41.21

25.97 28.96

20.63

R. SIDE VIEWTOP VIEW

E45412 LR27428

Dimensions shown in mm

14.51 28.91

16.53

41.21

25.97 28.96

20.63 te.com/energy

TE Connectivity (NYSE: TEL) is a $12 billion global technology leader. Our connectivity and sensor solutions are essential in today’s increasingly connected world. We collaborate with engineers to transform their concepts into creations – redefining what’s possible using intelligent, efficient and high-performing TE products and solutions proven in harsh environments.

Our 75,000 people, including 7,300 design engineers, partner with customers in close to 150 countries across a wide range of industries. We believe EVERY CONNECTION COUNTS – www.TE.com.

• Mining

• Nuclear power plants

• � OEMs

• Overhead distribution

• Petrochemical plants

• Railways

• Street lighting

WHEREVER ELECTRICITY FLOWS, YOU’LL FIND TE ENERGY

• Substations

• Transmission lines

• Underground distribution

• Windfarms

• Solar

• Hydro-electric te.com/energy © 2016 TE Connectivity Ltd. family of companies. All Rights Reserved. EPP-2783-AU-8/16

Raychem, TE Connectivity and the TE connectivity (logo) are trademarks of the TE Connectivity Ltd. family of companies. Other logos, product and Company names mentioned herein may be trademarks of their respective owners. While TE has made every reasonable effort to ensure the accuracy of the information in this brochure, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this brochure are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.

ENERGY /// STREET LIGHTING PHOTOCONTROLS

FOR MORE INFORMATION:

TE Customer Support Centers

NSW/QLD/NT/ACT: +61 (2) 9554 2695

VIC/TAS/SA: +61 (3) 9271 5243

WA: +61 (8) 9358 7806

New Zealand: +64 (9) 634 4580

Email: marketingANZ@te.com

INDUSTRIAL / LUMAWISE ALR 8000 SERIES

LUMAWISE ALR

8000 SERIES

PHOTOCONTROL

TE Connectivity’s (TE) advanced technology LUMAWISE ALR 8000 Series Photocontrol provides a durable, ultra-high performance, multi-voltage control especially designed for twenty-year operation in demanding roadway, street and area LED lighting applications.

TE’s LUMAWISE 8000 Series photocontrol design has eliminated electrolytic capacitors resulting in a truly long-life control. The 8000 Series design using a 30 AMP rated 120 VAC relay helps to ensure that our control will surpass 20,000 On/Off operation cycles per ANSI C136.10.

As is the case with all of our electronic controls, the 8000 Series utilizes our interlocking base/cap design for superior environmental protection. A high temperature base material, rated at a minimum of 138°C, along with a UV stabilized, opaque housing ensures our control will last over 20 years without degradation.

With additional new part numbers, the LUMAWISE 8000 Series now provides two photocontrols with surge protection up to 1025J and two photocontrols with ingress protection up to IP66.

BENEFITS

• Designed for LED lighting

• Supports multiple input voltages

• Rated life: 20 years

• 25mm, 20kA, 300 Joule MOV, standard

• Meets or exceeds ANSI C136.10

THE LUMAWISE ALR 8000

SERIES IS THE RESULT OF

OVER FIFTY YEARS OF

EXPERIENCE DESIGNING

AND DELIVERING HIGHLY-

RATED PHOTOCONTROLS

AND OTHER LIGHTING

ACCESSORIES AROUND

THE WORLD.

PAGE 2INDUSTRIAL / LUMAWISE ALR 8000 SERIES

LUMAWISE ALR 8000 SERIES

PHOTOCONTROL

APPLICATIONS

• Street and area LED lighting

• Roadway LED lighting

• Commercial outdoor LED lighting (i.e. parking, lots, car dealerships)

PRODUCT INFORMATION

Part Number Descriptive PN Color Energy Current Certification

BB3399-000 ALR-8090-VFS Blue 300J 20kA –

CZ9645-000 ALR-8090-VFS-FO Green 300J 20kA –

FG1245-000 ALR-8090-VFS-BK Black 300J 20kA –

G37412-000 ALR-8090-VFS-GN Green 300J 20kA –

2401414-1 ALR-8090-MFS Blue 800J 20kA UL

2401414-2 ALR-8090-HFS Blue 1025J 20kA UL

2388947-1 ALR-8090-VFS-FO-IP66 Green 300J 20kA –

2388950-1 ALR-8090-MFS-IP66 Blue 800J 20kA UL

ELECTRICAL

• Voltage rating: 105 – 305 VAC

• Frequency: 50/60 Hz

• Power consumption: Less than

0.5 watts at 120 VAC

• Relay rating: 30 AMP general purpose relay

• Load rating: Resistive: 1000 W Tungsten: 1800 VA Electronic ballast: 5 A

• Operating light levels: Standard

1.5 Fc on (optional 1 – 2.6 Fc)

• Time delay ON/OFF: Instant on, 2 – 5 second delay OFF

• Surge protection: Up to 1025J

• OFF/ON ratio: 1.5:1

• Fail mode: ON or OFF

• Light sensor: Non-drifting phototransistor

MECHANICAL

• Operating temperature rating:

-40°C to +65°C at 96% RH

• Rated life: 20 years

• Control: DC electromagnetic switch exceeds 20,000 ON/OFF operations per ANSI C136.10

• Ingress protection: Up to IP66

MATERIALS

• Base: High temperature polyester

(PBT)

• Gasket: Cross-linked polyethylene

• Cover: High impact polypropylene with UV stabilized polycarbonate window

• Connection: 3 pole locking type with brass contacts

• Dimensions: IP54 version:

Approximately 83mm diameter X 45mm high (not including contacts) IP66 version: Approximately 82mm diameter X 56mm high (not including contacts)

SPECIFICATIONS

• ANSI C136.10

https://www.te.com/usa-en/product-BB3399-000.html https://www.te.com/usa-en/product-CZ9645-000.html https://www.te.com/usa-en/product-FG1245-000.html https://www.te.com/usa-en/product-G37412-000.html https://www.te.com/usa-en/product-2401414-1.html https://www.te.com/usa-en/product-2401414-2.html https://www.te.com/usa-en/product-2388947-1.html https://www.te.com/usa-en/product-2388950-1.html

Part Number 8 0 90 - V F S - _ _ - _-_

INDUSTRIAL / LUMAWISE ALR 8000 SERIES

te.com © 2023 TE Connectivity. All Rights Reserved.

TE Connectivity, TE connectivity (logo) and Every Connection Counts are trademarks owned or licensed by TE Connectivity.

All other logos, products and/or company names referred to herein might be trademarks of their respective owners.

While TE has made every reasonable effort to ensure the accuracy of the information in this brochure, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.

06/23 ES

LUMAWISE ALR 8000 SERIES

PHOTOCONTROL

The 8000 series offers almost unlimited options ensuring your lighting network needs will be met.

If any additional part numbers are needed contact Product and Customer Support.

Series (Fail Mode)

8 = 8000 (ON)

Ingress Protection Blank = IP54

IP66 = IP66

Fail OFF Option FO = Fail OFF Option (leave blank if Fail ON)

Turn-On Level 1 = 1.0 Fc S = 1.5 Fc (ANSI Std) 2 = 2.0 Fc 3 = 2.6 Fc

Cap Color (Leave blank if ANSI Standard) BL = Blue BK = Black BR = Brown (Bronze) GN = Green GR = Gray MR = Maroon YL = Yellow OR = Orange

OFF/ON Ratio 0 = 1.5:1

Voltage 90 = 120/208/240/277

MOV Surge Protection V = 300J, 520V, 20kA, 25mm M = 800J, 580V, 20kA, 25mm H = 1025J, 750V, 20kA, 25mm

Light Sensor F = IR Filtered Phototransistor

ANSI Standard Cap Colors Fail ON Fail OFF

120V Gray Orange

208 / 240 / 277V Maroon –

120 / 208 / 240 / 277V Blue Green https://www.te.com/usa-en/customer-support/customer-service.html

BB3399-000

Electronic, 105 – 305 VAC, Utility, 1800 VA Load Rating (Ballast), Locking, ALR 8000 Series, ANSI Street Lighting Photocells

09/25/2024 03:15PM | Page 1 For support call+1 800 522 6752

Connectors > Lighting Connectors > Street Lighting Controls > Street Lighting Photocells

Load Rating (Ballast): 1800 VA

Grade: Utility

Operating Voltage Range: 105 – 305 VAC

Street Lighting Photo Control Technology: Electronic

Product Availability: Americas, Asia, Australia & New Zealand, Europe, Middle East & Africa

Features

Product Type Features

Light Sensor Filtered Silicon Phototransistor

Street Lighting Photo Control Technology Electronic

Electrical Characteristics

Operating Voltage Range 105 – 305 VAC

Load Rating (Ballast) 1800 VA

Load Rating (Tungsten) 1000 W

Fail Mode On

Surge Protection 20 kA

Operating Frequency 50 – 60 Hz

Relay Rating 30A General Purpose

Body Features

Compatible With Lamp Type LED

Primary Product Color Blue

Mechanical Attachment

Mounting Options Locking

BB3399-000 ACTIVE

LUMAWISE

TE Internal #: BB3399-000

Electronic, 105 – 305 VAC, Utility, 1800 VA Load Rating (Ballast), Locking, ALR 8000 Series, ANSI Street Lighting Photocells

View on TE.com >

ALR 8000 Series| https://www.te.com/en/plp/Zndb.html https://www.te.com/en/product-BB3399-000.html https://www.te.com/en/plp/Xrwjnl.html

Series, ANSI Street Lighting Photocells

09/25/2024 03:15PM | Page 2 For support call+1 800 522 6752

Mounting Options Locking

Housing Features

Housing Material High Impact Polypropylene with UV-

Stabilized Polycarbonate Window

Dimensions

MOV Diameter 25 mm

Product Diameter 81.53 mm[3.21 in]

Product Height 44.96 mm[1.77 in]

Usage Conditions

Operating Temperature Range -40 – 65 °C[-40 – 149 °F]

Operation/Application

Turn ON Light Level 1.5 (Optional 1 – 3) fc

Turn ON Time Delay Instant On seconds

Industry Standards

Compatible With Approved Standards Products ANSI C136.10

Product Availability

Product Availability Americas, Asia, Australia & New Zealand, Europe, Middle East & Africa

Packaging Features

Packaging Method Box

Other

Grade Utility

OFF/ON Ratio 1.5:1

Product Compliance For compliance documentation, visit the product page on TE.com>

EU RoHS Directive 2011/65/EU Compliant

EU ELV Directive 2000/53/EC Compliant

China RoHS 2 Directive MIIT Order No 32, 2016 No Restricted Materials Above Threshold

EU REACH Regulation (EC) No. 1907/2006 Current ECHA Candidate List: JUNE 2024

(241)

Candidate List Declared Against: JUNE

2022 (224)

SVHC > Threshold:

Cadmium oxide (13.5% in Component) https://www.te.com/en/product-BB3399-000.html

Series, ANSI Street Lighting Photocells

09/25/2024 03:15PM | Page 3 For support call+1 800 522 6752

Cadmium oxide (13.5% in Component) Article Safe Usage Statements:

Use personal protective equipment as required. Do not eat, drink or smoke when using this product. Recycle if possible and dispose of the article by following all applicable governmental regulations relevant to your geographic location.

Halogen Content Low Halogen - Br, Cl, F, I < 900 ppm per homogenous material. Also BFR/CFR/PVC

Free

Solder Process Capability Not applicable for solder process capability

Product Compliance Disclaimer

This information is provided based on reasonable inquiry of our suppliers and represents our current actual knowledge based on the information they provided. This information is subject to change. The part numbers that TE has identified as

EU RoHS compliant have a maximum concentration of 0.1% by weight in homogenous materials for lead, hexavalent chromium, mercury, PBB, PBDE, DBP, BBP, DEHP, DIBP, and 0.01% for cadmium, or qualify for an exemption to these limits as defined in the Annexes of Directive 2011/65/EU (RoHS2). Finished electrical and electronic equipment products will be CE marked as required by Directive 2011/65/EU. Components may not be CE marked.