Bucket_Truck_Spec_Sheet.pdf

April 1, 2024

This device shall be to the manufacture's standard. It shall be equipped with the manufacture's equipment and accessories which are included as standard in the advertised and published literature for the unit. No such item of equipment or accessories shall be removed or omitted for the reason that it was not specified in the bid.

If it is necessary to bid alternate equipment or to take exceptions to the specifications as set forth, this must be so stated in your bid. For each item, please place a X in the appropriate space (Yes__ No__) to signify whether or not you are in complete compliance with the specification. Failure to follow the format or answer the specification may cause your bid to be disqualified. If you need extra space to describe your product, please attach extra sheets. When doing this, be sure your description references the appropriate question number.

General Specifications

Comply Item Description Units Qty Yes No

Unit

1. 70' Articulating Overcenter Aerial Device with an insulating lower boom, insulating upper boom and an insulating system at the boom tip. For installation over the rear axle and to include the following features:

EA 1 ____ ____

A. Ground to Bottom of Platform Height: 70.3 feet (21.4 meters). ____ ____ B. Working Height: 75.3 feet (23.0 meters). ____ ____ C. Maximum reach to edge of platform with Upper Boom Non- overcenter

(working position): 44.8 feet (13.6 meters) at platform height of 38.7 feet (11.8 meters).

D. Maximum reach to edge of platform with Upper Boom Overcenter: 48.4 feet (14.8 meters) at platform height of 19.8 feet (6.0 meters).

E. Continuous Rotation. ____ ____ F. Lower Boom: Articulation is from 0 to 125 degrees. Insulator provides 15 inches of isolation in the lower boom.

G. Insulating Upper Boom: Articulation is from 0 to 270 degrees. The round filament wound fiberglass section provides a minimum of 19 feet (5.79 meters) of isolation.

H. Chain and Rod Leveling: Platform automatically maintains level during boom articulation by means of a high strength chain and fiberglass rods in the booms to maintain dielectric integrity. Lifetime system requires no major preventative maintenance. Platform level adjustment is easily accessible from external location on lower pivot.

I. Upper boom drive system features uniform speed, smooth and continuous articulation and low maintenance operation.

J. Maintenance Free Elbow: nitrided to prevent rust, increase hardness and eliminates the need for grease at the elbow.

K. Side-by-Side Boom Stow offers low travel height and easy platform access. ____ ____ L. The INSULATING UPPER CONTROL SYSTEM includes a single handle controller incorporating high electrical resistance components that are dielectrically tested to 40 kV AC with no more than 400 microamperes of leakage. The control handle is green in color to differentiate it from other non-tested controllers.

M. The INSULATING SECONDARY CONTROL SYSTEM includes control handles incorporating high electrical resistance components that are dielectrically tested to 40 kV AC with no more than 400 microamperes of leakage. These control handles are green in color to differentiate it from other non-tested controllers.

N. Platform capacity: 400 lbs. (181 kilograms) standard. ____ ____ O. Small Boom Tip Profile. ____ ____ P. Hydraulic system: Open center (full pressure), maximum flow of 6.0 to 6.5 gpm (22.7 to 24.6 lpm), maximum operating pressure of 3,000 psi.

Q. Diagnostic pressure test port is located at the lower control station to allow a technician to quickly and easily attach a test gauge to verify system and tool circuit pressure.

R. Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion. Paint is electrostatically applied to the inside as well as outside of fabricated parts then high temperature cured prior to assembly ensuring maximum coverage and protection.

S. Unit meets or exceeds ANSI 92.2 standards. ____ ____

2. Manual Upper Boom Stow Securing System with support cradle and tie down strap

3. Elevator Pedestal

4. Single, One (1) Man, Fiberglass Platform; fixed side mounted. 24 x 24 x 39 inches.

Proportional Speed, Upper Control Handle - with safety interlock and interlock guard. Located on the side of the platform nearest the upper boom, mounted on the shaft. Forward/back operates lower boom down/up, tiller operates rotation CW/CCW, and up/down operates upper boom up/down.

5. One (1) Platform Step - located on the side of the platform nearest the elbow in the stowed position

6. Platform Cover - Soft vinyl 24 x 24 inch (610 x 610 mm) EA 1 ____ ____

7. Platform Liner, 24 x 24 x 39 inches (610 x 610 x 991 mm), 70 kV Rating EA 1 ____ ____

8. Hydraulic Tool Circuit at Platform: Two (2) sets of tool couplers for open center tools, one (1) set located on each side of the platform.

9. Tool Circuit System Relief Pressure to be set to 2250 PSI EA 1 ____ ____

10. Secondary Stowage System: 12 VDC powered motor and pump assembly for temporary operation of the unit in a situation wherein the primary hydraulic source fails. Electric motor is powered by the chassis battery. Control is operated with an air plunger at the platform and a momentary switch located at the lower controls and the outrigger controls. This feature allows the operator to completely stow the booms, platform, and outriggers.

11. Slip Ring: Required for engine start/stop, secondary stowage system, and throttle control options

12. Primary A-Frame Outriggers with 5-degree swivel shoe EA 1 ____ ____

A. Maximum Spread: 140 inches to the outer edge of shoes ____ ____ B. Ground Penetration: 7 to 11 inches depending on chassis frame height ____ ____ C. Outrigger/Unit Selector Valve: reduces the potential for inadvertent outrigger movement during machine operation if outrigger controls are bumped

D. Outrigger Control Valves: located on the outrigger legs ____ ____ E. Outrigger Interlocks: will not allow the unit to be operated until the outriggers have been at least partially deployed

F. Outrigger Motion Alarms ____ ____

13. Auxiliary A-Frame Outriggers with 5-degree swivel shoe EA 1 ____ ____

A. Maximum Spread: 140 inches to the outer edge of shoes ____ ____ B. Ground Penetration: 7 to 11 inches depending on chassis frame height ____ ____ C. Outrigger Interlocks: will not allow the unit to be operated until the outriggers have been at least partially deployed

D. Outrigger Motion Alarms ____ ____

14. Hydraulic Outrigger Control Valves EA 1 ____ ____

15. Insulating Aerial Device, ANSI Category C, 46kV and Below EA 1 ____ ____

16. Powder Painted White EA 1 ____ ____

Unit & Hydraulic Acc.

EA 35 ____ ____

17. Subbase

18. Hydraulic Reservoir, 30 Gallon, Rectangular

19. Sight Gauge for Hydraulic Reservoir, Reservoir Mounted

20. Hydraulic Oil HVI-22 with Dye (Standard)

21. Standard Pump For PTO

22. Hot shift PTO for automatic transmission

23. Standard PTO/Machine Functionality: PTO won't engage until parking brake is set. -Once parking (holding) brake is set, PTO and machine functions are enabled. -If parking (holding) brake is disengaged, both PTO and machine functions are disabled.

24. Standard PTO/Transmission Functionality for Automatic Transmissions - If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear. Once the chassis is shifted back into gear the PTO will disengage.

For some truck configurations the PTO switch must be turned off to allow the transmission to shift into gear.

Body

25. 140 inch Flatbed, suitable for installing on any 4x2 or 4x4 chassis with an approximate clear CA dimension of 106-121 inches, built to the following specifications:

A. Basic flatbed fabricated from hot rolled steel. ____ ____ B. Steel treated for improved primer bond and rust resistance. ____ ____ C. Primer applied to exterior of flatbed. ____ ____ D. Automotive underseal applied to entire underside of flatbed. ____ ____ E. Flatbed finish paint color - Jet Black. ____ ____ F. All steel flatbed, 140 inches long x 96 inches wide. ____ ____ G. Floor made from 10 gauge galvanneal. ____ ____ H. Frame built with 4 inch high structural channel. ____ ____ I. 3 inch high rail installed around perimeter of flatbed. ____ ____ J. 3 inch high pivot rail installed at sides and rear of flatbed. ____ ____ K. Light channels installed at curbside and streetside rear. ____ ____

L. LED FMVSS lights and rear strobes.

M. 25 inch high u-shaped grab handle installed at rear of flatbed.

N. Toe step installed at curbside rear.

O. Platform rest assembly installed at curbside rear.

P. Mounting provisions for E-Z step provided at the rear of flatbed.

Q. Mounting provisions for bolt-on control stand.

R. Steel elevator guard, 90 inch long x 40 inch wide x 42 inch high.

26. T-40 Thru Box tool compartment 40 inches wide x 50 inches high x 96 inches long (1016 x 1270 x 2438 mm) with 26.5 inch (673 mm) deep curb- and streetside compartments with the following compartmentation:

A. Curbside: Single, vented compartment with two (2) vertical barn-style doors. Left side has two (2) fixed shelves. Right side has three (3) unequal transverse compartments open to streetside. Compartment bottom has 0.125 inch (3.175 mm) rubber liner.

B. Streetside: Single compartment with two (2) vertical barn-style doors. Left side has three(3) unequal transverse compartments open to curbside. Top center has two (2) fixed shelves. Top right has three (3) swivel rope hooks (0-0-3). Compartment bottom has .125 inch (3.175 mm) rubber.

C. Center compartment: Top-opening compartment with Flat Plate-lined lid.

Punched-metal face. Interior of compartment total volume of up to 40''W x 30''D x 29''H W/O floor.

D. Standard features: Bolt-on door locks. Gas shock door holders. Door locks are three-point t-handle latches with lock cylinders. Finish paint interior compartments the same as exterior. Front master locking handle. Integrated locking system installed.

E. Automotive undercoating applied to entire underside of body. ____ ____ F. Painted White ____ ____

Body and Chassis Accessories

27. Cab Guard, 140'' L, 12 GA Sheet Metal With Non-Skid Surface And Expanded

Metal Section At Front, Black Gator Hyde Coating

A. Cab Guard Mounting Kit ____ ____ B. Front Supports For Cab Guard ____ ____

28. ICC (Underride Protection) Bumper Installed At Rear EA 1 ____ ____

29. Rigid Style Pintle Hitch (30,000 LB MGTW with 6,000 LB MVL), 4-Bolt Face

Mount, Buyers PH15 (T-60 Style) (Forestry Applications)

30. Set Of D-Rings for Trailer Safety Chain, installed one each side of towing device mount.

31. Cab Guard Access Stirrup Step(s) With Grab Handle(s) At Curbside Rear Of Cab

Guard

32. Compartment Top Access Step from Body Floor EA 1 ____ ____

33. Retractable Ladder Step, Two Rungs, Textured Flat Black, Installed at Rear EA 1 ____ ____

34. Platform Access Ladder from Flatbed with Grab Handle EA 1 ____ ____

35. Platform Rest, Rigid with Rubber Tube EA 1 ____ ____

36. No Automatic Lower Boom Stow Securing System EA 1 ____ ____

37. Lower Boom Rest Weldment

38. Wood Outrigger Pad, 19.5'' x 19.5'' x 1.88'', With Fluorescent Orange Steel Band

Around The Outer Edges And Chain Handle

EA 4 ____ ____

39. Outrigger Pad Holder, 20'' L x 20'' W x 3.5'' H, Fits 19.5'' x 19.5'' x 2.25'' And

Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4'' Lip Retainer

EA 4 ____ ____

40. Mud Flaps With Logo (Pair) EA 1 ____ ____

41. Wheel Chocks, Rubber, 9.75'' L x 7.75'' W x 5.00'' H, with 4'' L Metal Hairpin

Style Handle (Pair)

42. Wheel Chock Holders (Pair), For Installation Under Flatbed Or Dump Body EA 1 ____ ____

43. U-Shaped Grab Handle EA 1 ____ ____

44. Small Grab Handle Installed At Rear EA 1 ____ ____

45. Slope Indicator Assembly (Pair) For Machine With Outriggers EA 1 ____ ____

46. Cone Holder, Horizontal Style with Vertical Pivot (Un-folds Upwards), For

Mounting On Front Bumper (Holds up to four 15''x15'' large cones)

47. Safety Harness & 4.5 FT Lanyard (Medium To X-large) EA 1 ____ ____

48. Driveaway Safety Kit

49. Vinyl manual pouch for storage of all operator and parts manuals

50. Modify Chassis Clear CA to 121 inches

Electrical Accessories

51. Lights and reflectors in accordance with FMVSS #108 lighting package.

(Complete LED, including LED reverse lights)

52. 4-Corner Strobe Lighting, Amber LED,Two (2) Round Lights in Front Corners of

Cab Guard and Two (2) Round Lights at Rear

53. Strobe Lights Wired Battery Hot EA 1 ____ ____

54. Dual Tone Back-Up With Outrigger Motion Alarm EA 1 ____ ____

55. PTO Hour Meter, Digital, with 10,000 Hour Display EA 1 ____ ____

56. 6-Way Trailer Receptacle (Pin Type) Installed At Rear EA 1 ____ ____

57. Electric Trailer Brake Controller (Tekonsha Voyager #9030) EA 1 ____ ____

58. Electrical Panel & Switches EA 1 ____ ____

59. Install secondary stowage system. EA 1 ____ ____

60. Install Outrigger Interlock System

61. Heavy Duty Secondary Stowage Pump

62. No Upper Boom Out of Stow Indicator

63. No Lower Boom Out of Stow Indicator

EA 1 ____ ____

EA 1 ____ ____

64. PTO Indicator Light Installed In Cab EA 1 ____ ____

Finishing Details

65. Powder Coat Unit Standard White

66. Finish Paint Body Accessories Above Body Floor White

67. Front and Rear Frame or Under Body Mounted Components To Be Painted Black

68. Vehicle Height Placard, Installed In Cab EA 1 ____ ____

69. Apply Non-Skid Coating to all walking surfaces EA 1 ____ ____

70. English Safety And Instructional Decals EA 1 ____ ____

71. Placard, HVI-22 Hydraulic Oil EA 1 ____ ____

72. Dielectric test unit according to ANSI requirements. EA 1 ____ ____

73. Stability test unit according to ANSI requirements.

74. Focus Factory Build

75. Inbound Freight

76. As Built Electrical And Hydraulic Schematics To Be Included In The Manual

Pouch

77. Stock Unit

Chassis

78. Chassis EA 1 ____ ____

EA 1 ____ ____

EA 1 ____ ____

EA 1 ____ ____

79. Chassis EA 1 ____ ____

A. 2025 Model Year ____ ____ B. Freightliner M2-106 Plus ____ ____ C. Regular Cab ____ ____ D. 4x2 Drivetrain ____ ____ E. Chassis Color - White ____ ____ F. Cummins B6.7 Engine ____ ____ G. 240 HP Engine Rating ____ ____ H. Allison 3500 RDS Automatic Transmission ____ ____ I. Air Brakes ____ ____ J. Clear Cab to Axle Length - 139 inches

Actual Cab to Axle Length - 142 inches

K. 33,000 LBS Gross Vehicle Weight Rating (GVWR) ____ ____ L. 13,220 LBS Front Axle Weight Rating (FAWR) ____ ____ M. 21,000 LBS Rear Axle Weight Rating (RAWR) ____ ____ N. 016-1C3 - Freightliner Horizontal Exhaust (Right-Horizontal-Behind

Cab-Horizontal)

O. Driver Controlled Locking Differential ____ ____ P. Park Brake In Rear Wheels ____ ____ Q. 204-215 Freightliner 50 Gallon Fuel Tank (Left Hand Under Cab) ____ ____ R. Freightliner - Pre-Wire Chassis with No Cab Backwall Pass-Thru (33U-011) ____ ____ S. No Idle Engine Shut-Down Required ____ ____ T. Air Conditioning ____ ____ U. AM/FM Radio ____ ____

Additional Pricing

80. Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90) days warranty for travel charges, limited lifetime structural warranty

Additional Options gr6594 Rectangle

USE OF OTHER NAMES AND REFERENCES:

Unless otherwise stated, the use of manufacturer's name and product numbers are for descriptive purposes and establishing general quality levels only. They are not intended to be restrictive. Bidders are required to state exactly what they intend to furnish, otherwise, it is fully understood that they shall furnish all items stated.

BROCHURES AND LITERATURE:

Your proposal must be accompanied by descriptive literature (marked), indicating the exact items to be furnished.

The term "as specified" will not be acceptable.