B01_Attachment_2_Statement_of_Work.pdf

STATEMENT OF WORK

FOR BLM LAW ENFORCEMENT VEHICLE OUFITTING

April 2024

Finished Vehicle Example Photos (not actual vehicle):

Gila District-Tucson Field Office

New vehicle: 2024 Chevrolet Tahoe, License Plate: I625034 Vehicle VIN: 1GNSKLED3RR211046

Components to install, items sorted by general location:

“X” indicates parts are supplied by installer and included in quote:

FRONT/BUMPER:

X-Provide and install push bumper with winch & synthetic rope.

X- Provide/install two small low profile, side facing Whelen LED lights or Fenix T3 style (red/blue combo-clear lens) mounted on front of vehicles with highest level of visibility to the sides.

X- Provide/install one 6 LED pod Fusion red/blue combo-clear lens, light bar/strip on front of vehicle facing forward.

X-Provide and install wiring on the below provided auxiliary lights (fabrication mounts may be needed depending on the provided bumper):

- Mount and install 4 provided Vision X cannon (green box) auxiliary light pods on bumper.

- Mount and install 4 provided Rigid Industries (yellow circles) auxiliary light pods on bumper.

- Mount and install one Vision X IR (red circle) light pod on bumper.

X- Provide and install Siren speaker mounted behind grill or bumper. (New speaker) X- Provide and install Wig-Wag Flasher kit for new vehicle Headlights.

REAR CARGO DOOR/BUMPER/TAILGATE:

X- Provide and install low profile surface mount 18LED Red-Blue-White override under tailgate wing.

X- Provide and install 2 small, side facing Whelen or Fenix T3 style LED lights (red/blue combo-clear lens) mounted on the rear of the vehicle with highest level of visibility to the sides, inside of vehicle or outside.

X- Install a brake light/backup light wig-wag flasher kit/assembly.

X-Provide and install one LED Dome light (red/white combo) on inside of rear hatch cargo door.

ROOF:

X- Provide and install a new Whelen Lightbar (54” Legacy Duo) red/blue/white or similar light bar with clear lenses & arrow function.

-Install/fabricate a small metal bracket with provided flag mount attached to light bar mount.

INSIDE WINDSHIELD/DASH:

X- Provide and install a 12volt plug under the dash or side of dash for mounted GPS unit to connect to.

-Install and run provided 12volt GPS wire from plug through ceiling for GPS (see set up picture below) -Install provided GPS mount on ceiling for GPS X- Provide and install a 12volt 3-plug / 2 USB plus near console for easy access and use from driver’s seat, connected to master kill switch on center console.

-Install two provided LED Dome lights (red/white combo). First one in front seat area above center console and second one in rear seat area over the rear seat/cargo area. Second light located in a position, so the light is overhead when the driver’s side rear door is opened. Also hooked up through main console master switch.

X- Provide and install Arges Remote Spotlight with controller and mounts.

-Install provided Stalker Dual DSR radar X- Provide and install 2-3 magnetic mics on console or dash, as necessary. (Location determined by user) X- Provide and install Ignition override / “Secure Idle” (safe stop, or similar) device with button installed to left of steering wheel on dash.

X-Provide a device or program vehicle to deactivate external vehicle sounds when exiting the vehicle with the vehicle running or not, to include no sounds or lights when the vehicle is locked or unlocked.

CONSOLE:

X- Provide and install a Troy or Havis brand metal console (22" standard console, 10" slope, 12" level).

Must have cup holders (Level 2), lock box/storage box (Level 3), and driver side arm rest. (This includes the new console, and the floor plate base mount). This box may include the sliding arm computer mounting hardware (“arm”) for a Panasonic CF-33 computer. (Docking Station to be provided) X- Provide and install electrical timer which operates all electrical components and set shut off time to 2- 3 hours if left on without ignition.

-Install provided Uniden Bearcat BCT15X analog scanner & faceplate on console (Slope 1) X- Provide and install antennas needed for Uniden Bearcat BCT15X scanner, Motorola APX8500 and shark fin VHF w/ cell, GPS & wifi only for Panasonic Toughbook CF-33.

-Install provided Motorola APX8500 faceplate on console (Slope 2) X-Provide and Install power wiring harnesses for Motorola APX8500 and SkyMira SATRAD X- Provide and install Whelen Series controller CCSRN3 (Whelen siren box device, 3-switch position lever with 18 buttons) or similar. Final model to be determined prior to ordering. (Slope 3) X- Provide and install PA mic/system (attached to smart siren device & external siren/speaker, and mic on the console) X- Provide and install 6 additional small rocker switches on console (Level 1) plus one additional lock relase:

-Front IR Light (Required on first rocker switch) -Rear brake light cutouts (Required on second rocker switch) -Front bumper Rigid Industries off-road fog lights (2 pairs/required on third rocker switch) -Front bumper Vision X off-road lights (2 pairs / required on fourth rocker switch) -Primary Gun Lock release (Required on fifth rocker using a momentary rocker) and a secondary gun lock release, push button style on lower B-Plillar) -SATRAD channel lock on (Required on sixth rocker switch)

X- Provide and install wiring and switches for tail-light blackout function (includes switch/relays/& wiring as necessary to cause complete blackout function while operating vehicle) X- Provide and install Ultra Stinger LED 12volt DC Smart Charge flashlight assembly with light.

BEHIND CONSOLE/REAR PASSENGER AREA BEHIND DRIVERS SEAT:

(**rear passenger seat only will be removed prior to delivery as seen below) X- Provide/install and/or fabricate a gunlock backplate and metal bracket for a rifle & shotgun mounted w/ 2 locks for AR-15 and Remington 870) with a 10 second timer. Gun locks must disable the long guns action and be mounted in a manner that affords immediate access to the firearms in the passenger’s compartment.

X-Provide and install shotgun lock device for Remington 870 shotgun.

X-Provide and install a “Blac-Rac” brand, Colt AR-15 Rifle Lock to fabricated gunlock mounting bracket.

X- Provide and install the 2 unlock switches as describe in "Console" section.

-Install two provided speakers: one for the Uniden scanner and the other for Motorola APX8500 -Install provided 600watt power inverter, hard wired, and mounted in rear passenger cargo area, with plug outlets easily accessible.

UNDER REAR SEAT OR APPLICABLE AREA:

FRONT PASSENGER FLOORBOARD:

X- Provide and install a computer power source for the docking tray connected to main console master switch.

PRISONER TRANSPORT CAGE:

X- Provide and install a single prisoner transport cage in right rear passenger seat position. Installation must not compromise a vehicles air bag system.

X- Provide and install a flat metal security panel on the right rear passenger door (to complete prisoner cage) X- Provide and install metal security screen or bars over right rear passenger door window (to complete prisoner cage) X- Deactivate/unplug the right rear passenger door lock and window controls on door but leave operable from driver’s controls. Assure the cage door electrical switch is protected from water/dirt (wrap in plastic and tape and secured inside door).

X- Provide and install rear or downward facing white LED light mounted on the front side of cage aimed at prisoner’s face.

REAR CARGO AREA:

X-Provide and install a large storage box (TruckVault, or similar storage box)

Vehicles Exterior:

-Install vehicle stripping kit (provided). Kit requires meeting specific policy requirements which will be provided. Photos shown represent example of requirements.

Additional Requirements:

-All quoters shall be with 450 miles of the following address:

Gila District Office

3201 E. Universal Way Tucson, AZ 85756

Coordination shall be made with Samuel Arnberger:

END ALL INSTALL ITEMS