Attachment III Install Manual CF1100 20ft x 24ft.pdf

PDF 1 MB Posted Jun 22, 2023

Attached to: CONSTRUCTION OF TWO (2) HOOP HOUSE GREENHOUSE STRUCTURES (HILO, HI)
Solicitation number: 12905B23Q0103
Issued by: Department of Agriculture Agricultural Research Service Field Research Implementation and Information Delivery Pacific West Area

About this file

Written by GovTribe AI · Dec 21, 2023

This solicitation requests proposals for the construction of two hoop house greenhouse structures in Hilo, Hawaii. The Agricultural Research Service of the Department of Agriculture seeks to award a fixed-price construction contract for the turnkey installation of the greenhouses, including all necessary materials, equipment, labor and technical support. Proposals are due by April 15, 2023. The period of performance is 120 calendar days following award. The contractor will be responsible for obtaining any required permits and coordinating inspections. Preference will be given to service-disabled veteran-owned small businesses.

View the file

Other files

File	Type	Posted
SF30_12905B23Q0103_0001.pdf	PDF	Jul 14, 2023
Site Visit Sign-In.pdf	PDF	Jul 14, 2023
Questions and Answers_12905B23Q0103.pdf	PDF	Jul 14, 2023
Attachment II SOW.pdf	PDF	Jun 22, 2023
Attachment I SF-18.pdf	PDF	Jun 22, 2023
Attachment VI ARS-372 - CONTRACTOR REQUEST FOR PAYMENT TRANSMITTAL.pdf	PDF	Jun 22, 2023
RFQ_12905B23Q0103 Terms and Conditions.pdf	PDF	Jun 22, 2023
Attachment V ARS-371 - CONSTRUCTION PROGRESS AND PAYMENT SCHEDULE.pdf	PDF	Jun 22, 2023
Attachment IV DOL WD HI20230001_031723.pdf	PDF	Jun 22, 2023

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

20'-0" AND 24'-0" WIDE WITH LEGS

INSTRUCTION MANUAL

COLD FRAME SERIES 1100

GREEN HOUSE SYSTEM

IMPORTANT!!!!!

NON - CODE COLD FRAMES REPRESENT A NON - CODE- NON

ENGINEERED DESIGN WITH CERTIFICATION UNAVAILABLE. IT IS

NOT RECOMMENDED THAT THIS HOUSE BE UTILIZED IN REGIONAL

AREAS REPRESENTING SNOW OR HIGH WIND FACTORS.

NOTE:

ENDWALL COLUMN SPACING ILLUSTRATED

MAY VARY TO ACCOMMODATE DOOR SIZING.

'-0" CENTER TO CENTER

'-0" CENTER TO CENTER '-0"

AutoCAD SHX Text

GENERAL CONTRACTORS LICENSE NO. 323391-B

AutoCAD SHX Text

FAX (909) 628-3774

AutoCAD SHX Text

SERVING AGRICULTURE SINCE 1946 A DIVISION OF JOHN L. CONLEY, INC.

AutoCAD SHX Text E

AutoCAD SHX Text

GREENHOUSE MANUFACTURING & SALES

AutoCAD SHX Text

4344 MISSION BLVD.

AutoCAD SHX Text

(909) 627-0981

AutoCAD SHX Text O

AutoCAD SHX Text I

AutoCAD SHX Text R

AutoCAD SHX Text P

AutoCAD SHX Text E

AutoCAD SHX Text U

AutoCAD SHX Text S

AutoCAD SHX Text R

AutoCAD SHX Text

MONTCLAIR, CA. 91763

AutoCAD SHX Text

(800) 377-8441

AutoCAD SHX Text R

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text

AutoCAD SHX Text T

AutoCAD SHX Text H

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text G

AutoCAD SHX Text S

AutoCAD SHX Text F

AutoCAD SHX Text L

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text L

AutoCAD SHX Text M

AutoCAD SHX Text O

AutoCAD SHX Text R i

TABLE - CONTENTS

INTRODUCTION -----------------------------------------------------------------------------------------------------------------------

DISCLAIMER ---------------------------------------------------------------------------------------------------------------------------

NOTICE TO CONLEY'S CUSTOMERS

PROTECT YOURSELF FROM ADDED COSTS----------------------------------------------------------------------------------

WARRANTY ---------------------------------------------------------------------------------------------------------------------------

NOTATION - INSTRUCTIONS PROVIDED ----------------------------------------------------------------------------------

GRADE AND PREPARE THE BUILDING SITE --------------------------------------------------------------------------------

LAYOUT AND SQUARE THE FOUNDATION ---------------------------------------------------------------------------------

FIND COLUMN CENTERS ----------------------------------------------------------------------------------------------------------

AUGER COLUMN HOLES ----------------------------------------------------------------------------------------------------------

-FSETTING THE LINES -----------------------------------------------------------------------------------------------------------

SLOPE LINES ---------------------------------------------------------------------------------------------------------------------------

MARK CENTERS ON COLUMN ---------------------------------------------------------------------------------------------------

MARK COLUMNS --------------------------------------------------------------------------------------------------------------------

SET COLUMNS -------------------------------------------------------------------------------------------------------------------------

COLUMN TO ARCH CONNECTOR -----------------------------------------------------------------------------------------------

INSTALLATION - ARCHES ------------------------------------------------------------------------------------------------------

PURLIN INSTALLATION ------------------------------------------------------------------------------------------------------------

INSTALL REMAINING ARCHES AND PURLINS ------------------------------------------------------------------------------

INSTALL "X" BRACING -------------------------------------------------------------------------------------------------------------

GIRT INSTALLATION (WOOD OR METAL) -----------------------------------------------------------------------------------

DOOR END WALL WITH METAL GIRTS ---------------------------------------------------------------------------------------

SOLID END WALL WITH METAL GIRTS ---------------------------------------------------------------------------------------

20'-0" COLD FRAME WITH LEGS ARCH PARTS LIST -----------------------------------------------------------------------

20'-0" COLD FRAME WITH LEGS END WALL PARTS LIST ----------------------------------------------------------------

20'-0" COLD FRAME WITH LEGS END WALL WITH DOOR

PARTS LIST -----------------------------------------------------------------------------------------------------------------------------

24'-0" COLD FRAME WITH LEGS ARCH PARTS LIST ----------------------------------------------------------------------

24'-0" COLD FRAME WITH LEGS END WALL PARTS LIST ---------------------------------------------------------------

24'-0" COLD FRAME WITH LEGS END WALL WITH DOOR

PARTS LIST ----------------------------------------------------------------------------------------------------------------------------

COVERING TRIM INSTALLATION -----------------------------------------------------------------------------------------------

Page 1 - 2

Page 3 - 5

Page 10 - 11

Page 12 - 13

Page 15 - 16

Page 17 - 18 ii

TABLE OF CONTENTS

COVERING TRIM INSTALLATION OPTIONS ---------------------------------------------------------------------------------

GABLE END BAR OPTION ---------------------------------------------------------------------------------------------------------

INSTALLATION OF POLY COVERING WITH TUBE LOCK ---------------------------------------------------------------

INSTALLATION OF POLY COVERING ON ARCHED BUILDINGS ------------------------------------------------------

INSTALLATION OF INFLATOR FAN --------------------------------------------------------------------------------------------

INFLATOR FAN ASSEMBLY ------------------------------------------------------------------------------------------------------

INSTALLATION OF POLY COVERING WITH VINNIPET SPRING -------------------------------------------------------

Page 27 - 28

ALL PRODUCTS ARE SOLD F.O.B. SHIPPING POINT, AND THE ATTACHED MEMORANDUM COPY OF

BILL OF LADING THAT INDICATES THAT MATERIAL SHIPPED HAS NOW, BY LAW, BECOME YOUR

PROPERTY AND IS AN ACKNOWLEDGMENT BY THE TRANSPORTATION COMPANY OF THE RECEIPT OF

THE MATERIALS IN GOOD CONDITION.

SAFE DELIVERY OF THIS SHIPMENT IS NOW THE RESPONSIBILITY OF THE CARRIER WHO ACTS AS YOUR

AGENT. WE WILL BE GLAD TO RENDER ASSISTANCE TO TRACE AND RECOVER LOST GOODS.

EXAMINE THE SHIPMENT CAREFULLY BEFORE SIGNING THE FREIGHT BILL. IF ANY DAMAGE IS NOTED, OR OF THE NUMBER OF PIECES DOES NOT AGREE WITH THE BILL OF LADING, INSIST THAT SHORTAGE OR

DAMAGE BE NOTED ON THE FREIGHT BILL BY THE CARRIERS AGENT. FAILURE TO DO SO MAY

JEOPARDIZE YOUR RECOVERY.

DO NOT REFUSE SHIPMENT AS THIS IS YOUR PROPERTY AND REFUSAL CAUSES UNNECESSARY DELAYS

AND SHORTAGE EXPENSES. ARRANGE WITH CARRIER WITHIN 15 DAYS TO INSPECT AND MAKE

REFERENCE THERE TO ON THE FREIGHT BILL. CONSULT YOUR CARRIER FOR DISPOSITION OF DAMAGED

ARTICLES.

THE FOLLOWING INSTRUCTIONS ARE GIVEN AS SUGGESTED GUIDELINES FOR GENERAL INSTRUCTIONS.

CONLEY'S MANUFACTURING AND SALES OR ANY OF THEIR EMPLOYEES SHALL NOT BE RESPONSIBLE FOR DAMAGES RESULTING FROM PURCHASERS IMPLEMENTATION OF THESE INSTRUCTIONS. PURCHASERS ALONE SHALL BE RESPONSIBLE FOR CONFORMANCE WITH ALL APPLICABLE LAWS, ORDINANCES, AND SAFETY STANDARDS IN CONSTRUCTING THIS GREENHOUSE AND ALL EQUIPMENT INSTALLED THEREIN.

SHOULD YOU HAVE ANY QUESTIONS CONCERNING THESE INSTRUCTION, COMPONENTS ETC..., PLEASE

MANUFACTURED PRODUCT.

INCLUDED IN THIS PACKAGE ARE INSTRUCTIONS AND DETAILED DRAWINGS PERTAINING TO YOUR CONLEY'S GREENHOUSE SYSTEM. STUDY THE INSTRUCTIONS BEFORE BEGINNING CONSTRUCTION TO

BECOME FAMILIAR WITH OUR PRODUCT AND HOW IT IS ASSEMBLED.

STORE ALL MATERIALS OFF THE GROUND ON WOOD BLOCKS. PROTECT ALL YOUR MATERIALS FROM

THEFT AND/OR DAMAGE. YOU MAY WISH TO DISCUSS BUILDERS RISK INSURANCE WITH YOUR

INSURANCE AGENT.

NOTICE TO CONLEY'S CUSTOMERS

PROTECT YOURSELF FROM ADDED COSTS

DISCLAIMER

INTRODUCTION

CONLEY'S MANUFACTURING AND SALES, THEIR EMPLOYEES OR REPRESENTATIVES, WILL NOT BE RESPONSIBLE FOR ANY DAMAGES TO GREENHOUSE COVERINGS, STRUCTURES, CROPS OR EQUIPMENT WHEN USED IN CONDUCTION WITH OUR TUBE - LOCK, OR ANY OTHER LOCKING DEVICE MANUFACTURED

BY CONLEY'S MANUFACTURING AND SALES OR OTHERS.

MAKE YOUR CLAIM PROMPTLY, THE TRANSPORTATION COMPANY WILL NOT CONSIDER A CLAIM

UNLESS IT IS PRESENTED WITHIN (9) MONTHS FROM THE DATE OF SHIPMENT. CARRIERS AGENT WILL

ASSIST YOU IN PREPARING A CLAIM.

CLAIMS FOR LOSS OR DAMAGE AND TRANSPORTATION CHARGES RESULTING FROM SHIPPING, MUST NOT BE DEDUCTED FROM THE INVOICE, NOR PATENT INVOICES WITH HELD AWAITING ADJUSTMENT OF SUCH CLAIMS, SINCE IT IS THE FUNCTION OF THE CARRIER TO GUARANTEE SAFE DELIVERY.

CHECK THE ITEMS RECEIVED WITH THE INVOICE. OF THERE IS ANY DISCREPANCY CONTACT US IMMEDIATELY GIVING FULL PARTICULARS. CLAIMS FOR SHORTAGE ATTRIBUTED TO OUR COUNT IN

PACKAGE MUST BE MADE WITHIN 10 DATES FORM THE SHIPMENT IS RECEIVED.

NO MERCHANDISE MAY BE RETURNED FOR CREDIT WITHOUT A RETURN GOODS TAG AND SHIPPING

INSTRUCTIONS FROM THE FACTORY.

WARRANTY

CONLEY'S MANUFACTURING AND SALES, PROVIDE INSTALLATION INSTRUCTIONS AND PRINTS ARE GEARED TOWARDS A QUALIFIED BUILDER WITH PRIOR GREENHOUSE BUILDING EXPERIENCE. IF A QUALIFIED BUILDER IS NOT AVAILABLE, CONLEY'S CAN SUPPLY AT AN ADDITIONAL CHARGE, A FACTORY TRANINED SUPERVISOR TO ASSIST LOCAL CREWS, OR ALTERNATIVELY, AT AN ADDITIONAL

CHARGE SUPPLY A CREW TO COMPLETE THE INSTALLATION OF MATERIALS.

NOTATION OF INSTRUCTIONS PROVIDED

GRADE AND PREPARE THE BUILDING SITE

LAYOUT AND SQUARE THE FOUNDATION

SEE PAGE 7 FOR GUTTER CONNECTED HOUSES

FIGURE 1 - LOCATING CORNER POINT 2

1. REMOVE THE GRASS AND DEBRIS DOWN TO SOLID SOIL.

2. LOCATE THE BUILDING CORNERS AND SET THE GRADING STAKES 5' BEYOND THE CORNERS.

3. A TRANSIT LEVEL IS NEEDED TO SURVEY THE AREA OF THE BUILDING. IN ORDER TO INSURE PROPER DRAINAGE AND EVEN HEATING, THE WIDTH SHOULD BE SET LEVEL AND THE LENGTH SHOULD BE SET LEVEL WITHIN APPROXIMATELY 1%. WITH A LEVEL GRADE, THE COLUMNS WILL NEED TO BE SET AT DIFFERENT HEIGHTS TO ACHIEVE A SLOPE FOR THE GUTTERS TO DRAIN (BUILDINGS WITH GUTTERS ONLY, SEE FIG 9). THE GRADE COULD ALSO BE PREPARED AT A 1/2 % SLOPE, FOR GUTTER BUILDINGS AND THE

COLUMNS CAN ALL BE SET AT THE SAME HEIGHT (SEE SHT 7 FOR OPTIONS)

4. CUT AND FILL THE SITE UNTIL IT IS AT THE RECOMMENDED GRADE.

1. ROUGHLY LOCATE THE CORNERS OF THE BUILDING AND DRIVE IN THE CORNER STAKES.

2. SET BATTER BOARDS APPROXIMATELY 6' ( OR ADEQUATE DISTANCE FROM AUGER CLEARANCE)

BACK FROM THE CORNERS IN EACH DIRECTION. SET INTERMEDIATE BATTER BOARDS OF THE

BUILDING IS LONGER THAN 50' TO KEEP THE LINES FROM SAGGING OR BLOWING IN THE WIND.

3. LOCATE THE FIRST BUILDING CORNER POINT AND MARK IT WITH A STAKE OR NAIL HEAD.

4. MEASURE FROM CORNER POINT 1, THE SPECIFIED DIMENSION OF THE BUILDING, TO LOCATE CORNER POINT 2. PULL A TIGHT LINE BETWEEN BATTER BOARD "1A" AND BATTER BOARD "2A", MAKING SURE THE LINE PASSES OVER CORNER POINT 1 AND CORNER POINT 2. FASTEN THE LINE ONTO THE BATTER BOARDS AND CHECK IT WITH TRANSIT. MAKE SURE THE BATTER BOARDS AND LINES ARE LEVEL (SEE FIG. 1). VARIATIONS IN THIS WILL ULTIMATELY AFFECT THE EAVE HEIGHT.

AutoCAD SHX Text 1A

AutoCAD SHX Text 1B

AutoCAD SHX Text 2B

AutoCAD SHX Text 2A

AutoCAD SHX Text

CORNER POINT 1

AutoCAD SHX Text

FIRST LOCATE BUILDING CORNER AND PLACE TRANSIT DIRECTLY OVER THE CORNER STAKE

AutoCAD SHX Text

CORNER POINT 2

AutoCAD SHX Text

LOCATE STRING LINE FOR THIS CORNER

AutoCAD SHX Text

CORNER POINT 4

AutoCAD SHX Text 4B

AutoCAD SHX Text 4A

AutoCAD SHX Text 3B

AutoCAD SHX Text 3A

AutoCAD SHX Text

MEASURE BUILDING CENTERLINE LENGTH

AutoCAD SHX Text

CORNER POINT 3

MEASURE BUILDING WIDTH

FIGURE 3 - (DIAGONAL METHOD)

FIGURE 4 - (TRIANGLE METHOD)

5. TO LOCATE THE THIRD CORNER POINT (FIG 2), YOU MAY USE ONE OF TWO METHODS, THE DIAGONAL

METHOD OR THE TRIANGLE METHOD.

THE DIAGONAL METHOD - RUN A LINE DIAGONALLY ACROSS FROM CORNER TO CORNER AND

ADJUST THE LINES UNTIL THE DIAGONAL DIMENSIONS ARE EQUAL. (SEE FIGURE 3).

THE TRIANGLE METHOD - CREATE A 90 ANGLE FROM THE FIRST LINE USING CORNER POINT 1 AS A

VERTEX. THIS ANGLE MAY BE ACCOMPLISHED BY USING TWO TAPE MEASURES AND THE CHART

LISTED BELOW (SEE FIGURE 4) (USE THIS METHOD FRO LARGER BUILDINGS WHERE THE LENGTH OF THE DIAGONAL EXCEEDS THE 100 FOOT TAPE MEASURE). WHEN YOU'VE LOCATED CORNER POINT 3, PULL YOUR SECOND LINE BETWEEN BATTER BOARD "1B" AND BATTER BOARD "3B" MAKING SURE IT PASSES OVER CORNER POINT 1 AND CORNER POINT 3. CHECK WITH TRANSIT MAKING SURE THAT

BATTER BOARDS AND LINES ARE LEVEL (SEE FIG. 2.)

FIGURE 2 - (LOCATING CORNER POINT 3)

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text 2A

AutoCAD SHX Text 2B

AutoCAD SHX Text 3A

AutoCAD SHX Text 3B

AutoCAD SHX Text 1A

AutoCAD SHX Text 1B

AutoCAD SHX Text

DIMENSION A + DIMENSION B + DIMENSION C

AutoCAD SHX Text 2 2 2

AutoCAD SHX Text 20' 15' 25'

AutoCAD SHX Text 24' 18' 30'

AutoCAD SHX Text 28' 21' 35'

AutoCAD SHX Text 32' 24' 40'

AutoCAD SHX Text 36' 27' 45'

AutoCAD SHX Text 40' 30' 50'

CORNER POINT 2

AutoCAD SHX Text

CORNER POINT 1

AutoCAD SHX Text

STRING LINE LOCATION FOR THIRD CORNER

AutoCAD SHX Text

CORNER POINT 3

AutoCAD SHX Text MEASURE THE DIAGONAL LINES AND ADJUST THE LINES UNTIL THE TWO DIAGONAL DIMENSIONS ARE EQUAL

CREATE A 90° ANGLE TO LOCATE STRING LINE FOR THIRD CORNER

FIGURE 6 - (LOCATING COLUMN CENTERS)

FIND COLUMN CENTERS

6. TO LOCATE THE FOURTH CORNER POINT (FIGURE 5), USING TWO TAPE MEASURES, FROM CORNER POINT 3 AND CORNER POINT 2, THE SPECIFIED LENGTH AND WIDTH. THE POINT AT WHICH THESE

LINES INTERSECT WILL BE CORNER POINT 4.

7. NOW YOU MAY PULL YOUR LAST TWO LINES AND FASTEN THEM TO THE APPROPRIATE BATTER

BOARDS. BE SURE TO CHECK THE LEVEL OF YOUR LINES (FIGURE 5).

1. MARK THE CORNER POINTS ON THE LINES, AND USE A 100 FOOT TAPE MEASURE TO MARK THE

INTERMEDIATE HOLE CENTERS ON THE LINES.

2. USING A LEVEL FOR VERTICAL ACCURACY, MARK THE HOLE CENTERS ON THE GROUND WITH NAILS.

PAINT THE NAIL HEADS WITH FLUORESCENT PAINT.

3. MEASURE DOWN THE WIDTH OF THE LINES AND MARK THE END WALL UPRIGHT CENTERS IN THE

SAME MANNER.

FIGURE 5 - (LOCATING CORNER POINT 4)

AutoCAD SHX Text 2A

AutoCAD SHX Text 2B

AutoCAD SHX Text 1A

AutoCAD SHX Text 1B

AutoCAD SHX Text 4A

AutoCAD SHX Text 4B

AutoCAD SHX Text 3B

AutoCAD SHX Text 3A

AutoCAD SHX Text

CORNER POINT 4

AutoCAD SHX Text

CORNER POINT 2

AutoCAD SHX Text

MEASURE BUILDING WIDTH

AutoCAD SHX Text

CORNER POINT 1

AutoCAD SHX Text

CORNER POINT 3

AutoCAD SHX Text

MEASURE BUILDING CENTERLINE LENGTH

AutoCAD SHX Text

PAINTED NAILS

AutoCAD SHX Text

MARK COLUMN CENTERS AT 4'-0", 5'-0", OR 6'-0" (SEE QUOTE / SALES ORDER)

AutoCAD SHX Text

6 INCHES (OR DESIRED STRING HEIGHT)

AutoCAD SHX Text

COLUMN CENTERLINES

MARK END WALL UPRIGHT CENTERS AT 10'-0"

CAUTION

BE SURE THERE ARE NO UNDERGROUND OR

OVERHEAD ELECTRICAL WIRES, WATER PIPES,

GAS LINES, ETC...ON OR NEAR THE JOB SITE.

FIGURE 7 - (AUGER HOLE)

FIGURE 8 - (OFFSETTING OF THE COLUMN SET LINES)

AUGER COLUMN HOLES

OFFSETTING THE LINES

1. AT THE POINT THAT THE LINES MEET THE BATTER BOARDS, CLEARLY AND ACCURATELY MARK THE

PLACEMENT OF THE LINES. MAKE SURE ALL THE BATTER BOARDS ARE MARKED.

2. REMOVE THE LINES.

3. AUGER HOLES TO REQUIRED DIMENSIONS.

4. AFTER DIGGING THE HOLES FOR END WALL UP RIGHTS, REFILL LOOSELY WITH DIRT, UNTIL READY

FOR USE, (SEE FIGURE 9-PAGE 7).

1. OFFSETTING OF THE LINES SHOULD BE DONE THE DAY THE CONCRETE IS POURED AND NOT LEFT

OVERNIGHT TO PREVENT STRETCHING OR KNOCKING DOWN LINES.

2. TO FIND THE COLUMN SET LINES, YOU MUST RESTRING THE FOUNDATION LAYOUT. FROM THE CENTER LINE MARKS ON THE BATTER BOARDS, MEASURE 1/2 THE SIZE OF THE COLUMN AND MOVE

THE LINES TO THAT MARK. (ALWAYS MOVE THE LINES IN THE SAME DIRECTION TO PREVENT

CONFUSION AND MISPLACEMENT OF COLUMNS (SEE FIGURE 8).

AutoCAD SHX Text

DEPTH

AutoCAD SHX Text

GRADE

AutoCAD SHX Text

DIAMETER

AutoCAD SHX Text

PREFERRED STRING HEIGHT (HEIGHT CHOSEN MUST NOT VARY THROUGHOUT LAYOUT)

AutoCAD SHX Text

OFFSET 1/2 OF COLUMN SIZE

AutoCAD SHX Text

END STRINGS FOR START/END POINT

AutoCAD SHX Text

COLUMN SET LINE MOVED TO RIGHT

ORIGINAL CENTERLINE MARK

SLOPE LINES

MARK CENTERS ON COLUMNS

NOTE: THIS TECHNIQUE TO BE USED WITH GUTTER HOUSES ONLY

FIGURE 9 - SLOPING COLUMN LINES

1. FROM THE CENTER LINE, MARK ON THE BATTER BOARDS (NOT THE COLUMN SET MARK) THE LENGTH OF LINES, AND

MARK THE INTERMEDIATE CENTERS.

2. MARK THE END WALL UPRIGHTS IN THE SAME MANNER. PLEASE NOTE THAT THE OFFSETS FOR END WALL INTERMEDIATE COLUMNS MAY BE DIFFERENT THAN THE OFFSET OF THE SIDE WALL COLUMNS DUE TO THE DIFFERENCE IN COLUMN SIZE. THE CENTER LINES OF COLUMNS MUST BE THE CENTER LINE END WALL COLUMNS.

1. IF SLOPING THE GRADE IS NOT DESIRED, THE THE SLOPE CAN BE ACHEIVED BY SETTING THE COLUMNS AT SPECIFIC HEIGHTS ALONG THE LENGTH OF THE BUILDING. PLEASE NOTE THAT THE UNDER GUTTER (UG) HEIGHT OF THE BUILDING IS MEANT TO BE FOR THE HIGH SIDE OF THE BUILDING (THE PEAK UG HEIGHT AT THE CENTER OF THE

BUILDING FOR LONGER THAN 300' BUILDINGS).

SLOPE THE COLUMN LINES ALONG THE LENGTH OF THE FOUNDATION KEEPING THE FRONT AND BACK COLUMN

LINES PARALLEL. THIS WILL INSURE PROPER DRAINAGE (SEE FIG. 9).

SLOPING "GUTTER BUILDINGS" FOR

PROPER WATER DRAINAGE

1. IT IS PREFERRED TO SLOPE THE GRADE FOR WATER DRAINING (GUTTERED) GREENHOUSES. SLOPE THE GRADE ALONG THE LENGTH OF THE FOUNDATION KEEPING THE FRONT AND BACK COLUMN LINES PARALLEL. A SLOPE OF 3/4" EVERY 12'-0" (APPROXIMATELY 1/2 % SLOPE) WILL INSURE PROPER DRAINAGE AT THE GUTTERS. IF THIS OPTION IS CHOSEN, THEN ALL COLUMNS CAN BE SET TO THE SAME HEIGHT, AND BE ABLE TO ACHIEVE A CONSTANT BUILDING HEIGHT. IF THE BUILDING IS VERY LONG (OVER 300' LONG), IT IS ADVISABLE TO HAVE THE PEAK AT THE CENTER OF THE BUILDING, AND HAVE (2) OUTLETS, (1) AT EACH THE END WALL. THIS DETERMINATION WILL NORMALLY BE

TAKEN CARE OF BY THE DESIGN TEAM AT CONLEY'S.

AutoCAD SHX Text

SLOPE COLUMN LINE 1/2% APPROX. (0R 3/4" DROP EVERY 12'-0) TYPICAL BOTH SIDES

FRONT AND BACK COLUMN LINES TO REMAIN PARALLEL

MARK COLUMNS

SET COLUMNS

FIGURE 10 - (MARKING COLUMNS)

FIGURE 11 - (SETTING THE COLUMNS)

1. TO FIND THE ABOVE GROUND COLUMN HEIGHT, MEASURE FROM THE TOP OF THE COLUMN, THIS DISTANCE, AND SUBTRACT THE STRING HEIGHT. MARK THE COLUMN AT THIS POINT WITH A FELT TIP

MARKER. CONTINUE WITH REMAINING COLUMNS. (SEE FIGURE 10).

1. POUR CONCRETE INTO THE FIRST HOLE. (2) 1/2" SLUMP IS THE MOST POPULAR MIX TO SUPPORT

COLUMNS.

2. PUSH THE COLUMN INTO THE CONCRETE AT THE CENTER MARK ON THE STRING (BE SURE THE COLUMN ISN'T ACTUALLY TOUCHING STRING) UNTIL THE MARK ON COLUMN LINES UP WITH THE

STRING. THE COLUMN MUST BE PLUMB IN BOTH DIRECTIONS BEFORE MOVING ON TO THE NEXT

COLUMN.

3. MOVE ON TO THE NEXT COLUMN, POUR CONCRETE THEN SET THE COLUMN. NEVER POUR ALL THE

CONCRETE FIRST THEN GO BACK AND SET COLUMNS, AS THE CONCRETE SETS UP TOO FAST.

1. PLACE THE FIRST THREE ARCHES INTO THE FIRST THREE AUGURED HOLES. (SEE PAGE 6 FOR HOLE

AUGURING).

AutoCAD SHX Text

STRING HEIGHT

AutoCAD SHX Text

CAUTION:

AutoCAD SHX Text

ABOVE GROUND COLUMN HEIGHT MINUS STRING HEIGHT

AutoCAD SHX Text

GRADE

AutoCAD SHX Text

AUGER HOLE

AutoCAD SHX Text

HOLES FOR COLUMNS

AutoCAD SHX Text

COLUMN SET IN CONCRETE ON CENTER

AutoCAD SHX Text

HOLES FOR END WALL UPRIGHT PIPERS

AutoCAD SHX Text

COLUMN SET LINES

AutoCAD SHX Text

STRING AND MARK ON COLUMN TO BE LINED UP

AutoCAD SHX Text

LEVEL

AutoCAD SHX Text

COLUMN SET LINE

CONCRETE

COLUMN TO ARCH CONNECTOR

INSTALLATION OF ARCHES

1. ATTACH THE FIRST ARCH TO THE CONNECTORS USING (4) 1/4 X 3/4" MACHINE BOLTS.

NOTE: DO NOT INSTALL THE MIDDLE BOLT.

1. ATTACH THE CONNECTOR TO THE COLUMNS USING 1 CLAMP AND (2) 3/8" X 1" MACHINE BOLTS PER

CONNECTOR.

AutoCAD SHX Text CONNECTOR COLUMN TO ARCH CLAMP (1 5/8" COLUMN) #C0155451 (2 7/8" COLUMN) #C0155501

AutoCAD SHX Text

(2) 3/8" HEX NUT #N9970300

AutoCAD SHX Text COLUMN TUBE 1 5/8" or 2 7/8"

AutoCAD SHX Text

(2) 3/8" X 1" MACHINE BOLT #B9970440

AutoCAD SHX Text CONNECTOR COLUMN TO ARCH HAND (1 5/8" COLUMN) #C0155450 (2 7/8" COLUMN) #C0155500

AutoCAD SHX Text

BOLT TWO ARCHES TOGETHER

AutoCAD SHX Text

(2) 1/4" X 3/4" MACHINE BOLT #B9970030

AutoCAD SHX Text

COLUMN CONNECTION

AutoCAD SHX Text

(2) 1/4" HEX NUT #N9970280

AutoCAD SHX Text

CHORD ARCH (20' ARCH #C0055351) (24' ARCH #C0055356)

14-14 X 1" TEK SCREW #S9970052

FIGURE 12 - (ARCH ASSEMBLY)

1. TIE OFF THE ARCH USING ROPES OR CABLES TO MAKE THE ARCH PLUMB AND SQUARE.

(MATERIALS FOR SECURING THE COLUMNS, ROPE / CABLE, IS NOT SUPPLIED BY CONLEY'S

MANUFACTURING SALES).

2. BOLT TWO MORE ARCHES TO THE LEGS USING (4) 1/4" X 3/4" MACHINE BOLTS PER ARCH.

FIGURE 13 - (ARCH ASSEMBLY)

PURLIN INSTALLATION

AutoCAD SHX Text 4', 5', or 6' CENTER TO CENTER

4', 5', or 6' CENTER TO CENTER

3. BOLT THE RIDGE PURLIN TO THE UNDERSIDE OF THE FIRST AND SECOND ARCHES USING (2) 1/4" X 3/4"

MACHINE BOLTS PER ARCH.

4. BOLT ON THE QUARTER POINT PURLINS TO THE FIRST AND SECOND ARCHES USING (2) 1/4" X 3/4"

MACHINE BOLTS PER ARCH.

5. ATTACH TWO MORE ARCHES. OVERLAP THE RIDGE PURLIN AT THE THIRD ARCH AND BOLT IT TO THE

THIRD AND FOURTH ARCHES WITH (2) 1/4" X 3/4" MACHINE BOLTS PER ARCH.

6. OVERLAP THE QUARTER POINT PURLINS AT THE THIRD ARCH AND BOLT THEM TO THE THIRD AND

FOURTH ARCHES.

AutoCAD SHX Text

3" PURLIN #P0001715

AutoCAD SHX Text

CHORD ARCH

AutoCAD SHX Text

(2) 1/4" X 3/4" MACHINE BOLT #B9970030

AutoCAD SHX Text

5" PURLIN #P0001840

AutoCAD SHX Text

CHORD ARCH

AutoCAD SHX Text

(2) 1/4" X 3/4" MACHINE BOLT #B9970030

AutoCAD SHX Text

RIDGE PURLIN

AutoCAD SHX Text

SIDE PURLINS

CHORD ARCH

FIGURE 15 - (" X " BRACING)

FIGURE 14 - (INSTALLING THE REMAINING PURLINS)

1. INSTALL THE REMAINING ARCHES, TWO AT A TIME, UNTIL THE FULL LENGTH OF THE BUILDING IS

COMPLETE.

1. BRACE STRAPS ARE INSTALLED AT EACH END OF THE BUILDING IN THE SECOND BAY. ADJUST THE

ARCHES UNTIL THEY ARE PLUMB AND SQUARE.

2. TRIM IF NEEDED.

INSTALL REMAINING ARCHES AND PURLINS

INSTALL "X" BRACING

AutoCAD SHX Text

ARCHES AT 6'-0" ON CENTER

AutoCAD SHX Text

PURLINS

AutoCAD SHX Text

"X" BRACING

4', 5', or 6' CENTER TO CENTER

3. USING A 10-16 X 3/4" SCREW AT EACH END OF THE BRACE STRAP, SCREW ONE END AT THE END OF THE

SECOND ARCH AND THE OPPOSITE END TO THE UNDERSIDE OF THE THIRD ARCH BELOW THE

QUARTER POINT PURLIN.

4. SCREW ON THE SECOND STRAP THE SAME WAY AS THE FIRST SO THAT THE STRAPS FORM AN "X".

REPEAT THIS AT THE REMAINING THREE LOCATIONS IN BUILDING.

AutoCAD SHX Text

ARCH

AutoCAD SHX Text

CHORD ARCH

AutoCAD SHX Text

BRACE STRAP 8' #B0001891

AutoCAD SHX Text

1ST PURLIN

AutoCAD SHX Text

(2) 10-16 X 3/4" TEK SCREW #S9970010

AutoCAD SHX Text

BRACE STRAP 8' #B0001891

AutoCAD SHX Text

(2) 10-16 X 3/4" TEK SCREW #S9970010

(2) 1/4" X 3/4" MACHINE BOLT #B9970030

FIGURE 16 - (WOOD GIRT INSTALLATION)

1. ATTACH THE 2 X 4 GIRT TO THE COLUMN

AND 2 X 4 SPLICE AS SHOWN BELOW.

NOTE: CONLEY'S MFG. DOES NOT SUPPLY

ANY LUMBER - THE CUSTOMER MUST

PURCHASE ALL LUMBER AND NAILS.

2. IF YOU HAVE PURCHASED THE PIPE CLAMP

AND HARDWARE FROM CONLEY'S MFG., THEN

YOU NEED TO DRILL A 5/16" HOLE FOR A

1/4" X 2" CARRIAGE BOLT 2 1/2" FROM THE

END OF THE GIRT FOR A 2 7/8" COLUMN OR

1 1/2" FROM THE END FOR A 1 5/8" COLUMN.

NOTE:

THIS DRAWING IS FOR REFERENCE

ONLY!!! CONLEY'S MFG. ONLY SUPPLIES

THE CLAMP ASSEMBLY WHEN ORDERED

BY THE CUSTOMER. ALL OTHER MATERIAL

MUST BE SUPPLIED BY THE CUSTOMER.

GIRT INSTALLATION

NOTE:

IF THE KOOL CEL DISTRIBUTION SYSTEM IS BEING INSTALLED, CHECK THE KOOL CEL INSTRUCTION

MANUAL FOR PROPER SLOPE AND DISTANCE TO INSTALL END WALL OR SIDE WALL GIRTS.

1. MARK THE COLUMNS WITH THE GIRT LOCATIONS.

2. CLAMP THE GIRTS TO THE COLUMN AND ADJUST

TO MAKE THEM LEVEL.

3. SECURE THE GIRTS TO THE COLUMNS WITH

(2) 14-14 X 1" TEK SCREWS PER COLUMN.

4. SPICE THE GIRTS BY OVERLAPPING THEM AND

SECURING BOTH GIRTS TO THE COLUMN

WITH (2) 14-14 X 1" TEK SCREW PER COLUMN.

FIGURE 16A - (METAL GIRT INSTALLATION)

DETAIL 1

DETAIL 2

DETAIL 3 - TOP KOOL CEL GIRT

TOP VIEW SPLICE

TOP VIEW SPLICE @ CORNERS

KOOL

CEL

GIRT

COLUMN

SPLICE PLATE

#S0000950

KOOL

CEL

GIRT

COLUMN

SIDE VIEW

KOOL

CEL

GIRT

ARCH

HAND

AutoCAD SHX Text

PIPE CLAMP

AutoCAD SHX Text

(2) 1/4" X 2" CARRIAGE BOLTS

AutoCAD SHX Text

2 X 4 GIRT

AutoCAD SHX Text

2 X 4 SPLICE

AutoCAD SHX Text

COLUMNS AT 6'-0" ON CENTER (THIS EXAMPLE ONLY)

AutoCAD SHX Text

COLUMN TUBE

AutoCAD SHX Text

14-14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

GIRT 5" #G0000XXX

AutoCAD SHX Text

OVERLAP GIRT 4"

AutoCAD SHX Text

14-14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

COLUMN

GIRT 5" #G0000XXX

DETAIL 1

FIGURE 17 - (END WALL DOOR FRAME)

1. DIG HOLES AT THE CENTER LINE OF JAMBS. THE DISTANCE BETWEEN THE JAMBS IS DETERMINED BY

THE DOORS WIDTH.

2. DOOR JAMBS DOESN'T HAVE TO GO ALL THE WAY UP TO THE ARCH. ENDWALL GIRTS MAY VARY ON YOUR

SIDEWALL HEIGHT.

2. ATTACH THE END WALL UPRIGHTS TO THE ARCH TAB WITH (2) 1/4" X 3/4" MACHINE BOLTS.

3. STAND THE DOOR JAMBS IN THE HOLES AND ATTACH IT TO THE TOP OF THE JAMB AND TO THE PREVIOUSLY INSTALLED TAB. ALIGN THE JAMB FLUSH WITH THE OUTSIDE EDGE OF THE ARCH AND

CONNECT IT TO THE TAB WITH (2) 3/8" X 1" MACHINE BOLT.

DOOR END WALL WITH METAL GIRTS

AutoCAD SHX Text

1/4" HEX NUT #N9970280

AutoCAD SHX Text

1/4" X 3/4" MACHINE BOLTS #B9970030

AutoCAD SHX Text

3/8" X 1" MACHINE BOLTS #B9970440

AutoCAD SHX Text

END WALL UPRIGHT TO ARCH TAB #T0030870

AutoCAD SHX Text

3/8" HEX NUT #N9970300

AutoCAD SHX Text

DOOR JAMB #J0000101 #J0000111

AutoCAD SHX Text

END WALL ARCH

AutoCAD SHX Text

DOOR HEADER

AutoCAD SHX Text

END WALL GIRT

AutoCAD SHX Text

END WALL GIRT

AutoCAD SHX Text

TAB

AutoCAD SHX Text

TAB

AutoCAD SHX Text

JAMB

AutoCAD SHX Text

JAMB

AutoCAD SHX Text

END WALL UPRIGHT

AutoCAD SHX Text

TAB

AutoCAD SHX Text

TAB

AutoCAD SHX Text

COLUMN

AutoCAD SHX Text

COLUMN

AutoCAD SHX Text

NOTE: HOW MANY SIDEWALL GIRTS DEPENDS ON YOUR SIDEWALL HEIGHT.

DETAIL 2

4. PLUMB JAMBS IN BOTH DIRECTIONS AND CEMENTS THE HOLES OR FILL THEM WITH CRUSHED ROCK

DEPENDING ON YOUR BUILDING. (SEE PAGE 15 FOR INFORMATION).

5. DRILL SCREW THE END WALL / HEADER JAMB TAB TO THE END WALL ARCH, JAMBS, AND AT THE HEADER WITH (2) 14-14 X 1" TEK SCREWS. (SEE PAGE 15 FOR TAB / GIRT / HEADER LOCATIONS).

6. LEVEL AND DRILL SCREW THE END GIRTS TO THE TABS AND INSIDE OF DOOR JAMBS WITH (2)

14-14 X 1" TEK SCREWS AT TAB JAMBS.

DETAIL 3

AutoCAD SHX Text

END WALL ARCH

AutoCAD SHX Text

(4) 14-14 X 1" TEK SCREWS #S9970052

AutoCAD SHX Text

END GIRT SEE MATERIAL SHIPPING LIST FOR PART NUMBERS

AutoCAD SHX Text

END WALL / HEADER TO JAMB TAB #T0030880

AutoCAD SHX Text

DOOR SLIDING JAMB #J0000101 #J0000110

AutoCAD SHX Text

(4) 14-14 X 1" TEK SCREWS #S9970052

AutoCAD SHX Text

END WALL / HEADER TO JAMB TAB #T0030880

AutoCAD SHX Text

HEADER GIRT (USE GIRT FOR YOUR DOOR HEADER)

AutoCAD SHX Text

(2) 14-14 X 1" TEK SCREW #S9970052

END GIRT SEE MATERIAL SHIPPING LIST FOR PART NUMBER

DETAIL 4

FIGURE 18 - (SOLID END WALL)

SOLID END WALL WITH METAL GIRTS

1. FOLLOW DIRECTIONS 1, 2, 4, AND 5 ON PAGES 15, 16, 17 AND 18 FOR END WALL INSTALLATION.

2. LEVEL AND DRILL SCREW THE END GIRTS TO THE TABS WITH (2) 14-14 X 1" TEK SCREWS AT EACH TAB.

REFER TO PAGE 20 AND 23 FOR GIRT AND END WALL UPRIGHT LOCATIONS.

3. SECURE THE END GIRTS TO THE END WALL UPRIGHTS WITH (2) 14-14 X 1" TEK SCREWS.

(SEE DETAIL 4 BELOW).

AutoCAD SHX Text

(2) 14-14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

JAMB / END WALL UPRIGHT #J0000101 #J0000111

AutoCAD SHX Text

END GIRT SEE MATERIAL SHIPPING LIST FOR PART NUMBER

AutoCAD SHX Text

END WALL GIRT

AutoCAD SHX Text

END WALL GIRT

AutoCAD SHX Text

TAB

AutoCAD SHX Text

COLUMN

AutoCAD SHX Text

JAMB

AutoCAD SHX Text

JAMB

AutoCAD SHX Text

TAB

AutoCAD SHX Text

COLUMN

AutoCAD SHX Text

DETAIL 5 (OPTION A -TAB)

DETAIL 5 (OPTION B - NO TAB)

AutoCAD SHX Text

5" ENDWALL GIRT

AutoCAD SHX Text

#14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

TAB #T0030880

AutoCAD SHX Text

COLUMN 2-7/8"

AutoCAD SHX Text USE: #14 X 1" TEK SCREW #S9970052 WHEN #14 X 1" RUNS OUT, #10 X 3/4" OR #10 X 1-1/4" CAN BE USED

AutoCAD SHX Text

JAMB/ END WALL UPRIGHT

AutoCAD SHX Text

#10 X 3/4" OR #10 X 1-1/4"

AutoCAD SHX Text

5" ENDWALL GIRT

AutoCAD SHX Text

#14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

COLUMN 2-7/8"

AutoCAD SHX Text USE: #14 X 1" TEK SCREW #S9970052 WHEN #14 X 1" RUNS OUT, #10 X 3/4" OR #10 X 1-1/4" CAN BE USED

AutoCAD SHX Text

JAMB/ END WALL UPRIGHT

#10 X 3/4" OR #10 X 1-1/4"

FIGURE 19 - (ARCH PARTS LIST)

20'-0" COLD FRAME WITH LEGS

ARCH PARTS LIST

ITEM QTY PART No. DESCRIPTION

BRACE STRAP 8'-0"1 4 B0001891

C0155451

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 514

N9970300 NUT HEX PLTD COARSE 3/8"4

C0055351 CHORD ARCH 154" RAD2

C0155450 CONN COLUMN TO ARCH HAND 1-5/82

ITEM QTY PART No. DESCRIPTION

BRACE STRAP 8'-0"1 4 B0001891

C0155501

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-22 2 7/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 514

N9970300 NUT HEX PLTD COARSE 3/8"4

C0055351 CHORD ARCH 154" RAD2

C0155500 CONN COLUMN TO ARCH HAND 2-7/82

1 5/8 COLUMN (PARTS LIST)

2 7/8 COLUMN (PARTS LIST)

AutoCAD SHX Text

FIGURE 20 - (END WALL PARTS LIST)

20'-0" COLD FRAME WITH LEGS

END WALL PARTS LIST

ITEM QTY PART No. DESCRIPTION

C0155451

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP 1-5/8

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055351 CHORD ARCH 154" RAD2

C0155450 CONN COLUMN TO ARCH HAND2

14 T0030870

T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000200 GIRT 5" X 20'-0"2

J0000101 SLIDING DOOR JAMB 10'-0"2

ITEM QTY PART No. DESCRIPTION

C0155501

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-22 2 7/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055351 CHORD ARCH 154" RAD2

C0155500 CONN COLUMN TO ARCH HAND 2-7/82

14 T0030870

T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000200 GIRT 5" X 20'-0"2

J0000111 SLIDING DOOR JAMB 10'-0"2

1 5/8 COLUMN - (END WALL PARTS LIST)

2 7/8 COLUMN - (END WALL PARTS LIST)

AutoCAD SHX Text

ADJUST FOR

DOOR SIZE

SUPPLIED

WITH DOOR

20'-0" COLD FRAME WITH LEGS

END WALL WITH DOOR PARTS LIST

FIGURE 21 - (END WALL PARTS LIST)

ITEM QTY PART No. DESCRIPTION

C0155451

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055351 CHORD ARCH 154" RAD2

C0155450 CONN COLUMN TO ARCH HAND 1-5/82

T0030870 T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000200 GIRT 5" X 20'-0"2

J0000101 SLIDING DOOR JAMB 10'-0"2

J0000111 SLIDING DOOR JAMB 12'-0"2

1 5/8 COLUMN - (END WALL PARTS LIST)

ITEM QTY PART No. DESCRIPTION

C0155501

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-22 2 7/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055351 CHORD ARCH 154" RAD2

C0155500 CONN COLUMN TO ARCH HAND 2-7/82

T0030870 T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000200 GIRT 5" X 20'-0"2

J0000101 SLIDING DOOR JAMB 10'-0"2

J0000111 SLIDING DOOR JAMB 12'-0"2

2 7/8 COLUMN - (END WALL PARTS LIST)

AutoCAD SHX Text

FIGURE 22 - (ARCH PARTS LIST)

24'-0" COLD FRAME WITH LEGS

ARCH PARTS LIST

ITEM QTY PART No. DESCRIPTION

BRACE STRAP 8'-0"1 4 B0001891

C0155451

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 514

N9970300 NUT HEX PLTD COARSE 3/8"4

C0055356 CHORD ARCH 190" RAD2

C0155450 CONN COLUMN TO ARCH HAND 1-5/82

1-5/8 COLUMN (PARTS LIST)

ITEM QTY PART No. DESCRIPTION

BRACE STRAP 8'-0"1 4 B0001891

C0155501

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 2 7/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 514

N9970300 NUT HEX PLTD COARSE 3/8"4

C0055356 CHORD ARCH 190" RAD2

C0155500 CONN COLUMN TO ARCH HAND 2-7/82

2-7/8 COLUMN (PARTS LIST)

AutoCAD SHX Text

FIGURE 23 - (END WALL PARTS LIST)

24'-0" COLD FRAME WITH LEGS

END WALL PARTS LIST

ITEM QTY PART No. DESCRIPTION

C0155451

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055356 CHORD ARCH 190" RAD2

C0155450 CONN COLUMN TO ARCH HAND 1-5/82

14 T0030870

T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000450 GIRT 5" X 24'-0"2

J0000100 SLIDING DOOR JAMB 10'-0"2

1-5/8 COLUMN - (END WALL PARTS LIST)

ITEM QTY PART No. DESCRIPTION

C0155501

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 2 7/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055356 CHORD ARCH 190" RAD2

C0155500 CONN COLUMN TO ARCH HAND 2-7/82

14 T0030870

T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000450 GIRT 5" X 24'-0"2

J0000100 SLIDING DOOR JAMB 10'-0"2

2-7/8 COLUMN - (END WALL PARTS LIST)

AutoCAD SHX Text

ADJUST FOR

DOOR SIZE

SUPPLIED

WITH DOOR

24'-0" COLD FRAME WITH LEGS

END WALL WITH DOOR PARTS LIST

FIGURE 24 - (END WALL WITH DOOR PARTS LIST)

ITEM QTY PART No. DESCRIPTION

C0155451

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055356 CHORD ARCH 190" RAD2

C0155450 CONN COLUMN TO ARCH HAND 1-5/82

T0030870 T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000450 GIRT 5" X 24'-0"2

J0000100 SLIDING DOOR JAMB 10'-0"2

J0000110 SLIDING DOOR JAMB 12'-0"2

1 5/8 COLUMN - (END WALL WITH DOOR PARTS LIST)

ITEM QTY PART No. DESCRIPTION

C0155501

B9970440

N9970280

P0001715 P0001840 S9970010

CONN. COLUMN TO ARCH CLAMP

BOLT / HH 3/8" X 1"

COLUMN TUBE T-44 1 5/8"

PURLIN 3" X 12'-4" SIDES

NUT HEX PLTD COARSE 1/4"

PURLIN 5" X 12'-4" UNDER RIDGE

10-16 X 3/4" TEK SCREW

B9970030 BOLT / HH 1/4" X 3/4" GRADE 516

N9970300 NUT HEX PLTD COARSE 3/8"8

C0055356 CHORD ARCH 190" RAD2

C0155500 CONN COLUMN TO ARCH HAND 2-7/82

T0030870 T0030880

TAB END WALL UPRIGHT

TAB END WALL / HEADER TO JAMB

G0000450 GIRT 5" X 24'-0"2

J0000100 SLIDING DOOR JAMB 10'-0"2

J0000110 SLIDING DOOR JAMB 12'-0"2

2 7/8 COLUMN - (END WALL WITH DOOR PARTS LIST)

AutoCAD SHX Text

FIGURE 25 - (COVERING TRIM INSTALLATION)

COVERING TRIM INSTALLATION

1. SECURE THE TUBE LOCK AND 2X LUMBER TO THE COLUMN CONNECTION WITH VICE GRIPS. MAKE

SURE THAT THEY ARE PLUMB AND LEVEL. DRILL A 5/16" HOLE THROUGH THE TUBE LOCK AND

2X LUMBER.

2. BOLT THE TUBE LOCK AND 2X LUMBER TO THE COLUMN CONNECTION WITH A 1/4" X 2" CARRIAGE

BOLT.

1 5/8 COLUMN

2 7/8 COLUMN

STEEL GIRT OPTION FOR ANY SIZE COLUMN

AutoCAD SHX Text

TUBE LOCK II OPTION I SPLICE BOW OPTION II END COMBO OPTION III

AutoCAD SHX Text

TUBE LOCK II OPTION I

AutoCAD SHX Text

(2) 1/4" X 3/4" MACHINE BOLT #B9970030 WITH (2) 1/4" HEX NUT

AutoCAD SHX Text

ARCH

AutoCAD SHX Text

COLUMN TO HAND #C0155450

AutoCAD SHX Text

TUBE LOCK II

AutoCAD SHX Text

1/4" X 2" CARRIAGE BOLT #B9971360 2X LUMBER NOT SUPPLIED

AutoCAD SHX Text

(2) 3/8" X 1" MB (2) 3/8" HEX NUT

AutoCAD SHX Text

1/4" X 2" CARRIAGE BOLT #B9971360

AutoCAD SHX Text

CONN. COLUMN TO ARCH #C0155501

AutoCAD SHX Text

(2) 3/8" HEX NUT #N9970300

AutoCAD SHX Text

COLUMN

AutoCAD SHX Text

5/16" X 1 3/4" MACHINE BOLT #B9970270

AutoCAD SHX Text

CLAMP TUBE #C0101700

AutoCAD SHX Text

CONNECTOR #C0155500

AutoCAD SHX Text

(2) 3/8" X 1" MACHINE BOLT #B9970440

AutoCAD SHX Text

TUBE LOCK II

AutoCAD SHX Text

TAB SIDE GIRT WOOD #T0030700

AutoCAD SHX Text

1/4" X 2" CARRIAGE BOLT #B9971360

AutoCAD SHX Text

CONN. COLUMN TO ARCH #C0155451

AutoCAD SHX Text

14-14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

TUBE LOCK BASE

AutoCAD SHX Text

10-16 X 3/4" TEK SCREW #S9970010

AutoCAD SHX Text

KOOL CEL GIRT #K0000788 OR SIMILAR

AutoCAD SHX Text

COLUMN

AutoCAD SHX Text

TUBE LOCK BASE

AutoCAD SHX Text

10-16 X 3/4" TEK SCREW #S9970010

METAL SIDE GIRT

1. OPTION 1 - TUBE LOCK II - INSTALL THE TUBE LOCK TO THE END ARCH WITH A 10-16 X 3/4" TEK SCREWS AT 16" ON CENTER TYPICAL. SEE THE MATERIALS LIST FOR TUBE LOCK PART NUMBER.

DETAIL 2

COVERING TRIM INSTALLATION OPTIONS

2. OPTION 2 - TUBE LOCK SPLICE- IF YOUR BUILDING IS LONGER THAN THE POLY SHEETS SUPPLIED, YOU WILL HAVE A SPLICE BOW. IT WILL BE PLACED ON THE ARCH JUST BEFORE THE POLY SHEETS END.

ATTACH IT TO THE ARCH WITH 10-16 X 3/4" TEK SCREW AT 16" ON CENTER SOME BUILDINGS WILL HAVE THE SPLICER BOW AT THE ENDWALLS OF THE BUILDING, FOR FASTENING THE ROOF POLY AND

ENDWALL POLY ON SEPARATE CHANNELS.

AutoCAD SHX Text

10-16 X 3/4" TEK SCREW #S9970010

AutoCAD SHX Text

TUBE LOCK II

AutoCAD SHX Text

ARCH

AutoCAD SHX Text

10-16 X 3/4" TEK SCREW #S9970010

AutoCAD SHX Text

ARCH

TUBE LOCK SPLICE BOW

1. OPTION 3 - ARCH END COMBO FOR A FIBERGLASS END WALL COVERING, USE AN ALUMINUM ARCH

END COMBO. ATTACH IT TO THE END WALL ARCH WITH 10-16 X 3/4" TEK SCREWS.

GABLE END BAR OPTION

DETAIL 3

ALUMINUM SPLICE GABLE END BAR

AutoCAD SHX Text

10-16 X 3/4" TEK SCREW #S9970010

AutoCAD SHX Text

CHORD ARCH

AutoCAD SHX Text

PURLIN

AutoCAD SHX Text

ALUMINUM ARCH END COMBO SEE MATERIAL SHIPPED LIST FOR PART NUMBER

AutoCAD SHX Text

END WALL GIRTS WOOD OR METAL

AutoCAD SHX Text

END WALL UPRIGHT

AutoCAD SHX Text

SPLICE GABLE END BAR #S0001100

AutoCAD SHX Text

SPLICE GABLE END BAR #S0001100

AutoCAD SHX Text

ALUMINUM ARCH END COMBO

(2) 10-16 X 3/4" TEK SCREW #S9970010

DETAIL 2 (WOOD SIDEWALL GIRT OPTION SHOWN)

GABLE END BAR OPTION

W O

O D

P T

I O

STEEL

AutoCAD SHX Text

5" END WALL STEEL GIRT

AutoCAD SHX Text

14-14 X 1" TEK SCREW #S9970052

AutoCAD SHX Text

TAB #T0030880

AutoCAD SHX Text

WOOD BY OTHERS BY OTHERS

AutoCAD SHX Text

ALUM COMBO STRAIGHT #A0000252 #A0000254

AutoCAD SHX Text

ALUM ARCH COMBO END #A2400000 OR #A1150000

AutoCAD SHX Text

ALUM ARCH COMBO END #A2400000 OR #A1150000

AutoCAD SHX Text ALUM COMBO STRAIGHT #A0000252 or #A0000254

AutoCAD SHX Text

(2) 1/4" X 2" CARRIAGE BOLT (WOOD OPTION ONLY)

AutoCAD SHX Text CLAMP TUBE (WOOD OPTION ONLY) #C0101390 AT 1-5/8" COLUMN ONLY SEE SHT 18 FOR 2-7/8" COLUMN

AutoCAD SHX Text

1/4" HEX NUT (WOOD OPTION ONLY)

AutoCAD SHX Text

SPLICE GABLE END BAR #S0001100

AutoCAD SHX Text

%%UALUMINUM SPLICE GABLE END BAR

AutoCAD SHX Text

ALUM ARCH COMBO END

AutoCAD SHX Text

ALUM ARCH COMBO END #A0000210

AutoCAD SHX Text

(2) 10-16 X 3/4" TEK SCREW

#10 X 3/4" TEK SCREW AT GIRT LOCATIONS

INSTALLATION OF POLY COVERING

WITH TUBE LOCK

1. APPLY THE POLY FILM (ONE OR MORE LAYERS) OVER THE PREVIOUSLY INSTALLED TUBE LOCK.

2. INSERT THE LONG LEG OF THE CAP FIRST. KEEP IT NEXT TO THE INFLATED SIDE OF THE COVERING.

3. TEK SCREW THE TUBE LOCK CAP TO THE BASE OR ARCH END COMBO WITH A 10-16 X 3/4" TEK SCREWS AT EACH END. TO INSTALL STRAIGHT 6' TUBE LOCK CAPS ON ARCHED SEGMENTS, FIRST SCREW IN ONE END AND WITH THE USE OF A MALLET, WORK YOUR WAY AROUND THE ARCH TO ACHIEVE

THE REQUIRED CURVATURE.

DETAIL 2

DETAIL 3

AutoCAD SHX Text

POLY

FIGURE 26 - (POLY INSTALLATION)

INSTALLATION OF POLY COVERING

ON ARCHED BUILDINGS

1. ON SINGLE BUILDINGS, ROLL OUT THE POLY LENGTHWISE NEXT TO BUILDING.

2. WAD UP THE POLY (APPROX. EVERY 20') AND TIE IT WITH ROPES ON THE SIDE OF THE POLY FURTHEST

FROM THE BUILDING.

3. THROW ROPES OVER THE BUILDING AND PULL THE POLY ONTO THE BUILDING. REPEAT THIS

PROCEDURE FOR MULTIPLE LAYERS OF POLY.

4. INSTALLING POLY REQUIRES A MINIMUM OF FOUR PEOPLE, TWO PEOPLE TO HOLD THE POLY IN PLACE AT THE END OF THE BUILDING, ONE ON EACH SIDE. THE OTHER TWO PEOPLE STARTING AT THE OPPOSITE END OF BUILDING TO INSTALL THE TUBE LOCK CAP SIMULTANEOUSLY, ON EACH SIDE OF

BUILDING. (SEE PAGE 27 FOR POLY LOCKING INSTRUCTIONS).

5. SECURE THE TUBE LOCK CAP WITH TEK SCREWS AT EACH END.

INSTALLATION OF INFLATOR FAN

(OPTIONAL)

1. ATTACH THE INFLATOR FAN HANGER TO THE GUTTER WITH (2) 5/16" X 3/4" MACHINE BOLTS WITH

WASHERS AND (2) 5/16" HEX NUTS.

CAUTION - BE SURE THERE ARE NO UNDERGROUND OR OVERHEAD ELECTRICAL WIRES, WATER

PIPES, GAS LINES, ETC. ON OR NEAR THE JOB SITE.

2. CLAMP THE INFLATOR FAN HOSE TO THE INFLATOR FAN (CLAMPS SUPPLIED WITH FAN).

3. ATTACH THE MOUNTING PLATE WITH THE FAN TO THE INFLATOR FAN HANGER WITH (2) 1/4" X 3/4"

MACHINE BOLTS AND (2) 1/4" HEX NUTS.

4. TO CUT THE POLY, PUT YOUR HAND BETWEEN THE 2 LAYERS OF POLY AND CUT A 3" "X" SLIGHTLY SMALLER THAN THE SMALL END OF THE INFLATOR COUPLING IN THE BOTTOM LAYER OF THE POLY, ABOVE THE INFLATOR FAN.

5. SLIP ONE RUBBER WASHER OVER THE INFLATOR COUPLING. SLIDE THE COUPLING BETWEEN THE TWO

LAYERS OF POLY AND PUSH THE SMALL END THROUGH THE HOLE MADE IN STEP 2.

6. SLIP THE SECOND RUBBER WASHER OVER THE SMALL END OF THE COUPLING AND SCREW ON THE

NUT, SANDWICHING THE BOTTOM LAYER OF POLY BETWEEN THE TWO RUBBER WASHERS.

7. CLAMP THE INFLATOR HOSE TO THE INFLATOR COUPLING.

8. SECURE THE POLY WITH THE TUBE LOCK. (SEE PAGE 28).

9. WIRE THE INFLATOR FAN TO 110 VOLT ELECTRICAL OUTLET.

10. CLAMP THE INTAKE TO THE INFLATOR FAN.

11. CUT A HOLE IN THE SIDE WALL COVERINGS SO THE EXTERIOR VENT CAN SLIDE

THROUGH.

12. SLIDE THE VENT THROUGH THE SIDE WALL AND CLAMP THE INTAKE HOSE TO IT.

(BE CAREFUL TO KEEP THE CIRCLE CONTINUOS SO THAT

WHEN POLY IS INFLATED THE WALL WILL NOT RIP.)

(FOR DOUBLE POLY COVERING OPTION)

INFLATOR FAN ASSEMBLY

FIGURE 1

FIGURE 31 - (INFLATOR FAN ASSEMBLY)

(FOR DOUBLE POLY COVERING OPTION)

AutoCAD SHX Text

1. APPLY POLY FILM (ONE OR MORE LAYERS) OVER PREVIOUSLY INSTALLED VINNIPET BASE.

2. INSERT ONE EDGE OF THE VINNIPET SPRING INTO THE VINNIPET BASE. KEEPING POLY TIGHT WEAVE

THE VINNIPET SPRING INTO THE BASE SECURING THE POLY.

3. INSERT ONE EDGE OF THE SECOND VINNIPET SPRING INTO THE VINNIPET BASE. KEEPING POLY TIGHT

WEAVE THE SECOND VINNIPET SPRING INTO THE BASE SECURING THE POLY.

WARRANTY CONLEY'S MFG. AND SALES, THEIR EMPLOYEES OR REPRESENTATIVES, WILL NOT BE RESPONSIBLE FOR ANY DAMAGE TO GREENHOUSE COVERING, STRUCTURES, CROPS OR EQUIPMENT WHEN USED IN CONJUNCTION WITH OUR TUBE - LOCK, OR ANY OTHER LOCKING DEVICE MFG,D BY

C.M.S. OR OTHERS.

INSTALLATION OF POLY COVERING

WITH VINNIPET SPRING

AutoCAD SHX Text

POLY

AutoCAD SHX Text

POLY

AutoCAD SHX Text

%%UNOTE: TEK SCREW ALL VINNIPET BASE AT A MINIMUM OF 16" ON CENTER

USE DOUBLE CLIPS WHEN INSTALLING 32' OR WIDER POLY, DOUBLE POLY, AND/OR BUILDING IS LOCATED IN HIGH WIND AREA.

Insert from: "Page 14-Model.pdf"

Sheets and Views

Model

File details come from the government source that posted it. Updated Jun 22, 2023.