Attachment A, Project Specification.pdf

Attachment A Project Specification General Repairs to Gambrel Salt Storage Building

Wyoming County, Tunkhannock Stockpile #01 Building # 0470103 Project #11582205

A. Work Included

1. There is no Labor and Industry Occupancy Certificate for this building. The contractor will provide all necessary Labor and Industry permits as required to complete the following work.

2. Replace 2 concrete filled pipe bollards at entrance with 8”dia., .125”wall, concrete filled, galvanized pipe bollards. Bollards will measure 5’ above grade, 3’below grade set in concrete frost proof footings, minimum 16” diameter. Footings to extend above grade 2” and be coned around base of bollard to prevent water accumulation. Provide plastic protective sleeves cut to length, safety yellow with reflective tape for each bollard. All concrete to be 5000psi.

3. Re-nail loose T-111 siding throughout. Only galvanized nails and hardware to be used.

4. Pressure wash and stain all exposed exterior pressure treated wood surfaces including walls, posts and bracing with a waterproofing product similar to those manufactured by Thompson, Behr, Olympic, Cabot or approved equal.

5. Replace damaged or missing fascia boards throughout. Paint to match existing.

6. Repair damaged foundation wall at rear right interior with plywood in kind. Use only full sheets of pressure treated plywood and galvanized fasteners.

7. The contractor is responsible to provide onsite superintendence throughout the course of this work. The contractor will ensure the safety of all persons having business in and around the project area by providing barricades and warning devices as prescribed by local and OSHA requirements.

B. SUBMITTAL PROCEDURE

1. Submit Two (2) copies of all items shown on submittal schedule except for "samples" original copies required.

Wyoming County, Tunkhannock Stockpile #01

2. Identify project number, project name and location, and contractor's name and address on all submittals.

3. Provide space for review stamps of Contractor and Department. Put contractor stamp of approval on each item submitted.

4. Revise and resubmit submittals as required, identify all changes made since previous submittal.

5. No work shall be performed until all submittals are approved by the Department. Work performed prior to submittal approval is performed at the Contractor's risk and may be subject to repair, replacement or other corrective measures as deemed necessary by the Department with no additional contract time or money.

6. Review of shop drawings will be general and for the limited purpose of checking for general conformance with the design; and shall not relieve the Contractor from the responsibility for proper fitting and construction of the work, nor from furnishing materials and work required by the Contract which may not be indicated on the shop drawings when reviewed.

7. The submittals required by this contract are subject to reproduction for the Department's internal use only. By signature on this bid proposal, both the Contractor and the equipment manufacturer authorize the Department to reproduce any materials including printed literature and training aids, submitted in fulfillment of this contract.

C. MANUFACTURER'S INSTRUCTIONS

1. When specified in individual specification sections, submit manufacturer's printed instructions for delivery, storage, assembly, installation, start-up, adjusting and finishing, and maintenance, in quantities specified for product data.

2. Identify conflicts between manufacturer's instructions and contract documents.

D. MANUFACTURER'S CERTIFICATES

1. When specified in individual specification sections or on submittal schedule, submit manufacturer's certificates to for review.

Wyoming County, Tunkhannock Stockpile #01

2. Indicate that material or product conforms to or exceeds specified requirements. Submit supporting reference date, affidavits and certifications as appropriate.

3. Certificates may be recent or previous test results on material or product, but in all cases must be acceptable to Department.

E. SUBMITTAL SCHEDULE

1. Abbreviations:

SoSu - Source of Supply CoCh - Color Chart DeDa - Descriptive Data or Catalog Cuts Cert - Certificates ShDr - Shop or Installation Drawings Samp – Samples

2. Schedule: (See below)

Description of items to be submitted

SoSu DeDa ShDr CoCh Samp Cert

1. Cost Breakdown X X

2. Work Schedule X X

3. Galvanized steel pipe X X X

4. Plastic bollard sleeves X X

5. Galvanized fasteners

6. Waterproofing X X

7. Final Deliverable Items 3 ring binder

X X

8. Digital Photos X

9. L&I Permit Documents X X X X

10. Concrete slips X X

11. Waste receipts X X