Attachment 2 Paint Specification.pdf

Data Pages

113.12SG

Pro Industrial™

Waterbased Alkyd Urethane Enamel Semi-Gloss B53-1150/2150 Series

CHARACTERISTICS

Pro Industrial Waterbased Alkyd Urethane Enamel is a premium quality interior-exterior enamel formulated with a urethane modified alkyd resin system for high performance. It provides beauty and durability when applied to interior-exterior surfaces such as properly prepared drywall, wood, masonry and metal. It brings together the convenience and ease of use of a waterborne coating with the performance and coating characteristics of a traditional oil-based enamel.

• Excellent washability & flow & leveling

• Excellent touch up

• Easy application & cleanup

• Resistant to yellowing compared to traditional alkyds

• Suitable for use in USDA inspected facilities

For use on properly prepared:

Steel, Galvanized & Aluminum, Drywall, Concrete and Masonry, and Wood.

Finish: 50-70° @60° Color: Most colors Recommended Spreading Rate per coat:

Wet mils: 4.0-5.0 Dry mils: 1.4-1.7 Coverage: 320-389 sq.ft. per gallon Theoretical Coverage: 545 sq. ft. per gallon

@ 1 mil dry Approximate spreading rates are calculated on volume solids and do not include any application loss.

Note: Brush or roll application may require multiple coats to achieve maximum film thickness and uniformity of appearance.

Drying Schedule @ 4.0 mils wet, @ 50% RH:

Drying, and recoat times are temperature, humidity, and film thickness dependent.

@77°F To touch 1-2 hours To recoat 4 hours

Tinting with CCE only:

Base oz. per gallon Strength Extra White 0-6 SherColor Deep Base 4-12 SherColor Ultradeep Base 10-14 SherColor

Extra White B53W02151 (may vary by color)

V.O.C. (less exempt solvents):

less than 50 grams per litre; 0.42 lbs. per gallon

As per 40 CFR 59.406

Volume Solids: 34 ± 2% Weight Solids: 51 ± 2% Weight per Gallon: 10.94 lb Flash Point: N/A Vehicle Type: Urethane modified alkyd Shelf Life: 36 months, unopened

COMPLIANCE

As of 03/10/2020, Complies with:

OTC Yes OTC Phase II Yes SCAQMD Yes CARB Yes CARB SCM 2007 Yes Canada Yes LEED® v4 & v4.1 Emissions No LEED® v4 & v4.1 V.O.C. Yes EPD-NSF® Certification No MIR-Manufacturer Inventory NSF® Certification

No

MPI® No

APPLICATION

Temperature:

minimum 50°F / 10°C maximum 100°F / 37.8°C air, surface, and material At least 5°F above dew point

Relative humidity: 85% maximum The following is a guide. Changes in pressures and tip sizes may be needed for proper spray characteristics.

Always purge spray equipment before use with listed reducer. Any reduction must be compatible with the existing environmental and application conditions.

Reducer: Water Airless Spray:

Pressure 2000 p.s.i.

Hose 1/4 inch I.D.

Tip .013 - .017 inch Filter 60 mesh Reduction Not recommended Brush Nylon-polyester Roller Cover 1/4-1/2 inch woven

If specific application equipment is listed above, equivalent equipment may be substituted.

Apply paint at the recommended film thickness and spreading rate as indicated on front page. Application of coating below minimum recommended spreading rate will adversely affect coating performance.

No painting should be done immediately after a rain or during foggy weather.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. Apply coating evenly while maintaining a wet edge to prevent lapping.

SPECIFICATIONS

Steel:

1 coat Pro Industrial Pro-Cryl Primer 2 coats Pro Industrial Waterbased Alkyd Urethane Aluminum and Galvanizing:

1 coat Pro Industrial Pro-Cryl Primer 2 coats Pro Industrial Waterbased Alkyd Urethane Concrete Block (CMU):

1 coat Pro Industrial Heavy Duty Blockfiller or Loxon Acrylic Block Surfacer 2 coats Pro Industrial Waterbased Alkyd Urethane Concrete-Masonry:

1 coat Loxon Concrete & Masonry Primer (if needed) 2 coats Pro Industrial Waterbased Alkyd Urethane Drywall:

1 coat ProMar 200 Zero V.O.C. Primer 2 coats Pro Industrial Waterbased Alkyd Urethane Wood, exterior:

1 coat Exterior Wood Primer 2 coats Pro Industrial Waterbased Alkyd Urethane Wood, interior:

1 coat Premium Wall & Wood Primer 2 coats Pro Industrial Waterbased Alkyd Urethane

The systems listed above are representative of the product’s use, other systems may be appropriate.

03/2020 www.sherwin-williams.com continued on back

Pro Industrial™

Waterbased Alkyd Urethane Enamel Semi-Gloss

SURFACE PREPARATION

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Do not use hydrocarbon solvents for cleaning.

Remove all surface contamination by washing with an appropriate cleaner, rinse thoroughly and allow to dry. Existing peeled or checked paint should be scraped and sanded to a sound surface. Glossy surfaces should be sanded dull. Stains from water, smoke, ink, pencil, grease, etc. should be sealed with the appropriate primer/sealer. Recognize that any surface preparation short of total removal of the old coating may compromise the service length of the system.

Iron & Steel - Minimum surface preparation is Hand Tool Clean per SSPC-SP2. Remove all oil and grease from surface per SSPC-SP1.

For better performance, use Commercial Blast Cleaning per SSPC-SP6. Primer recommended for best performance Aluminum - Remove all oil, grease, dirt, oxide and other foreign material per SSPC-SP1. Prime the area the same day as cleaned.

Galvanizing - Allow to weather a minimum of six months prior to coating. Solvent Clean per SSPC-SP1. When weathering is not possible, or the surface has been treated with chromates or silicates, first Solvent Clean per SSPC-SP1 and apply a test patch. Allow paint to dry at least one week before testing adhesion. If adhesion is poor, brush blasting per SSPC-SP16 is necessary to remove these treatments. Rusty galvanizing requires a minimum of Hand Tool Cleaning per SSPC-SP2, prime the area the same day as cleaned.

Concrete Block - Surface should be thoroughly clean and dry. Air, material and surface temperatures must be at least 55°F (13°C) before filling. Use Pro industrial Heavy Duty Block Filler or Loxon Acrylic Block Surfacer. The filler must be thoroughly dry before topcoating.

Masonry - All masonry must be free of dirt, oil, grease, loose paint, mortar, masonry dust, etc.

Clean per SSPC-SP13/Nace 6/ ICRI No. 310.2R, CSP 1-3. Poured, troweled, or tilt-up concrete, plaster, mortar, etc. must be thoroughly cured at least 30 days at 75°F. Form release compounds and curing membranes must be removed by brush blasting. Brick must be allowed to weather for one year prior to surface preparation and painting. Prime the area the same day as cleaned.

Weathered masonry and soft or porous cement board must be brush blasted or power tool cleaned to remove loosely adhering contamination and to get to a hard, firm surface. Apply one coat Loxon Conditioner, following label recommendations.

Wood - Surface must be clean, dry, and sound.

Prime with recommended primer. No painting should be done immediately after a rain or during foggy weather. Knots and pitch streaks must be scraped, sanded and spot primed before full coat of primer is applied. All nail holes or small openings must be properly caulked.

SURFACE PREPARATION

Previously Painted Surface - If in sound condition, clean the surface of all foreign material.

Smooth, hard or glossy coatings and surfaces should be dulled by abrading the surface. Apply a test area, allowing paint to dry one week before testing adhesion. If adhesion is poor, additional abrasion of the surface and/or removal of the previous coating may be necessary. Retest surface for adhesion. If paint is peeling or badly weathered, clean surface to sound substrate and treat as a new surface as above. Recognize that any surface preparation short of total removal of the old coating may compromise the service length of the system.

Mildew- Prior to attempting to remove mildew, it is always recommended to test any cleaner on a small, inconspicuous area prior to use. Bleach and bleaching type cleaners may damage or discolor existing paint films. Bleach alternative cleaning solutions may be advised.

Mildew may be removed before painting by washing with a solution of 1 part liquid bleach and 3 parts water. Apply the solution and scrub the mildewed area. Allow the solution to remain on the surface for 10 minutes. Rinse thoroughly with water and allow the surface to dry before painting.

Wear protective eyewear, waterproof gloves, and protective clothing. Quickly wash off any of the mixture that comes in contact with your skin. Do not add detergents or ammonia to the bleach/ water solution.

PERFORMANCE

System Tested: (unless otherwise indicated) Substrate: Steel Surface Preparation: SSPC-SP10 Finish:

1 coat Waterbased Alkyd Urethane, 5 W.F.T.

Adhesion:

Method: ASTM D3359 method B Result: 4B Pencil Hardness:

Method: ASTM D3363 Result: 4H Flexibility:

Method: Method: ASTM D522, 180°bend, 1/4” mandrel Result: Pass Dry Heat Resistance:

Method: ASTM D2485 Result: 200°F Block Resistance:

Lab assessment Excellent

Resistance to Yellowing:

Lab assessment Excellent

No painting should be done immediately after a rain or during foggy weather.

Do not paint on wet surfaces.

Check adhesion by applying a test strip to determine the readiness for painting.

SAFETY PRECAUTIONS

Before using, carefully read CAUTIONS on label.

Refer to the Safety Data Sheets (SDS) before use.

FOR PROFESSIONAL USE ONLY.

Published technical data and instructions are subject to change without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

CLEANUP INFORMATION

Clean spills, spatters, hands and tools immediately after use with soap and warm water. After cleaning, flush spray equipment with compliant cleanup solvent to prevent rusting of the equipment. Follow manufacturer’s safety recommendations when using solvents.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

HOTW 03/10/2020 B53W01153 09 39

FRC

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative or visit www.paintdocs.com to obtain the most current version of the PDS and/or an SDS.

113.05A

Pro Industrial™ Pro-Cryl®

Universal Primer B66-1300 Series

CHARACTERISTICS

Pro Industrial Pro-Cryl® Universal Primer is an advanced technology, self cross-linking acrylic primer. It is rust inhibitive and was designed for both construction and maintenance applications. It can be used as a primer under water-based or solvent-based high performance topcoats.

Features:

• Rust inhibitive, corrosion resistant

• Single component

• Early moisture resistant

• Fast dry

• Lower temperature application 40°F

• Interior and exterior use

• Suitable for use in USDA inspected facilities

For use on properly prepared:

Steel, Galvanized & Aluminum, wood

Finish: Low Sheen Color: Off White, Medium Grey, and Red Oxide Recommended Spreading Rate per coat:

Wet mils: 5.0-10.0 Dry mils: 1.9-3.8 Coverage: 160-320 sq.ft. per gallon Theoretical Coverage: 609 sq. ft. per gallon

@ 1 mil dry Approximate spreading rates are calculated on volume solids and do not include any application loss.

Note: Brush or roll application may require multiple coats to achieve maximum film thickness and uniformity of appearance.

Drying Schedule @ 6.0 mils wet, @ 50% RH:

Drying, and recoat times are temperature, humidity, and film thickness dependent.

@40°F @77°F @120°F To touch 2 hours 40 minutes 20 minutes Tack free 8 hours 2 hours 1 hour To recoat 16 hours 4 hours 2 hours

Tinting: DO NOT TINT

Off White B66W01310 (may vary by base)

V.O.C. (less exempt solvents):

less than 50 grams per litre; 0.42 lbs. per gallon

As per 40 CFR 59.406 Volume Solids: 38 ± 2% Weight Solids: 49 ± 2% Weight per Gallon: 10.09 lb Flash Point: N/A Shelf Life: 36 months, unopened

COMPLIANCE

As of 04/09/2020, Complies with:

OTC Yes OTC Phase II Yes SCAQMD Yes CARB Yes CARB SCM 2007 Yes Canada Yes LEED® v4 & v4.1 Emissions Yes LEED® v4 & v4.1 V.O.C. Yes EPD-NSF® Certified Yes MIR-Manufacturer Inventory NSF® Certification

Yes

MPI® Yes

APPLICATION

Temperature:

minimum 40°F maximum 120°F air, surface, and material At least 5°F above dew point

Relative humidity: 85% maximum The following is a guide. Changes in pressures and tip sizes may be needed for proper spray characteristics.

Always purge spray equipment before use with listed reducer. Any reduction must be compatible with the existing environmental and application conditions.

Reducer: Water

Airless Spray:

Pressure 2000 p.s.i.

Hose 1/4 inch I.D.

Tip .015 - .019 inch Filter 60 mesh Conventional Spray:

Gun Binks 95 Fluid Nozzle 66 Air Nozzle 63 PB Atomization Pressure 60 p.s.i.

Fluid Pressure 25 p.s.i.

Reduction: as needed up to 5 % by volume Brush Nylon-polyester Roller Cover 3/8 inch woven If specific application equipment is listed above, equivalent equipment may be substituted.

Apply paint at the recommended film thickness and spreading rate as indicated. Application of coating above maximum or below minimum recommended spreading rate may adversely affect coating performance.

Stripe coat crevices, welds, and sharp angles to prevent early failure in these areas. For best results on rusty surfaces, always apply first coat by brush.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle.

No painting should be done immediately after a rain or during foggy weather.

For optimal performance, this primer should be topcoated.

For exterior exposure, this primer should be topcoated within 14 days. If 14 days is exceeded remove all surface contamination by washing with an appropriate cleaner, rinse thoroughly and allow to dry. Finish with appropriate topcoat.

SPECIFICATIONS

Acceptable Water Based topcoats:

1-2 coats Pro Industrial Acrylic Coating or Pro Industrial Acrylic Dryfall Pro Industrial DTM Acrylic Pro Industrial Multi-Surface Acrylic Pro Industrial Pre-Catalyzed Epoxy Pro Industrail Pre-Catalyzed Urethane Pro Industrial Water Based Acrolon 100 Pro Industrial Water Base Alkyd Urethane Pro Industrial Water Based Catalyzed Epoxy Sherwin-Williams Architectural Coatings

Acceptable Solvent Based topcoats:

1-2 coats Pro Industrial High Performance Epoxy or Pro Industrial Urethane Alkyd

The finishes listed above are representative of the product’s use, other finishes may be appropriate.

04/2020 www.sherwin-williams.com continued on back

Pro Industrial™ Pro-Cryl®

Universal Primer

SURFACE PREPARATION

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Do not use hydrocarbon solvents for cleaning.

Remove all surface contamination by washing with an appropriate cleaner, rinse thoroughly and allow to dry.

Existing peeled or checked paint should be scraped and sanded to a sound surface. Glossy surfaces should be sanded dull. Stains from water, smoke, ink, pencil, grease, etc. should be sealed with the appropriate primer-sealer. Recognize that any surface preparation short of total removal of the old coating may compromise the service length of the system.

Iron & Steel - Minimum surface preparation is Hand Tool Cleaning per SSPC-SP2. Remove all oil and grease from the surface per SSPC-SP1. For better performance, use Commercial Blast Cleaning per SSPC-SP6. Prime the area the same day as cleaned.

Self priming Aluminum - Remove all oil, grease, dirt, oxide and other foreign material per SSPC-SP1. Self priming.

Galvanizing - Allow to weather a minimum of six months prior to coating. Solvent Clean per SSPC- SP1. When weathering is not possible, or the surface has been treated with chromates or silicates, first Solvent Clean per SSPC-SP1 and apply a test patch. Allow paint to dry at least one week before testing adhesion. If adhesion is poor, brush blasting per SSPC-SP16 is necessary to remove these treatments. Rusty galvanizing requires a minimum of Hand Tool Cleaning per SSPC-SP2, prime the area the same day as cleaned. Self priming.

Previously Painted Surfaces - If in sound condition, clean the surface of all foreign material. Smooth, hard or glossy coatings and surfaces should be dulled by abrading the surface. Apply a test area, allowing paint to dry one week before testing adhesion. If adhesion is poor, additional abrasion of the surface and/or removal of the previous coating may be necessary.

Retest surface for adhesion. If paint is peeling or badly weathered, clean surface to sound substrate and treat as a new surface as above. Recognize that any surface preparation short of total removal of the old coating may compromise the service length of the system.

Wood - Surface must be clean, dry and sound. Prime with recommended primer. No painting should be done immediately after a rain or during foggy weather.

Knots and pitch streaks must be scraped, sanded and spot primed before full coat of primer is applied. All nail holes or small openings must be properly caulked.

SURFACE PREPARATION

Mildew- Prior to attempting to remove mildew, it is always recommended to test any cleaner on a small, inconspicuous area prior to use. Bleach and bleaching type cleaners may damage or discolor existing paint films. Bleach alternative cleaning solutions may be advised.

Mildew may be removed before painting by washing with a solution of 1 part liquid bleach and 3 parts water.

Apply the solution and scrub the mildewed area. Allow the solution to remain on the surface for 10 minutes.

Rinse thoroughly with water and allow the surface to dry before painting. Wear protective eyewear, waterproof gloves, and protective clothing. Quickly wash off any of the mixture that comes in contact with your skin. Do not add detergents or ammonia to the bleach/water solution.

PERFORMANCE

System Tested: (unless otherwise indicated) Substrate: Steel Surface Preparation: SSPC-SP10 Finish: 1 coat Pro Industrial Pro-Cryl Off White 1 coat Pro Industrial Acrylic Coating Adhesion:

Method: ASTM D4541 Result: 500 p.s.i.

Corrosion Weathering:

Method: ASTM D5894, 10 cycles, 3360 hours Result: Passes Direct Impact Resistance:

Method: ASTM D2794 Result: greater than 140 inch lb.

Dry Heat Resistance:

Method: ASTM D2485 Result: 200°F

Flexibility:

Method: ASTM D522, 180° bend, 1/4 inch mandrel Result: Passes Moisture Condensation Resistance:

Method: ASTM D4585, 100°F, 1250 hours Result: Passes

Pencil Hardness:

Method: ASTM D3363 Result: B

Salt Fog Resistance:

Method: ASTM B117, 1250 hours Result: Passes

Provides performance comparable to products formulated In Lieu of federal specification: AA50557 and Paint Specification: SSPC-Paint 23.

SAFETY PRECAUTIONS

Before using, carefully read CAUTIONS on label.

Refer to the Safety Data Sheets (SDS) before use.

FOR PROFESSIONAL USE ONLY.

Published technical data and instructions are subject to change without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

CLEANUP INFORMATION

Clean spills, spatters, hands and tools immediately after use with soap and warm water. After cleaning, flush spray equipment with compliant cleanup solvent to prevent rusting of the equipment. Follow manufacturer’s safety recommendations when using solvents.

HOTW 04/20/2020 B66W01310 03 40

HOTW 04/20/2020 B66A01320 04 39

HOTW 04/20/2020 B66N01310 04 39

FRC

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative or visit www.paintdocs.com to obtain the most current version of the PDS and/or an SDS.