Attachment 2 - GEORGE COBB DD FY25 - Specification.pdf

USCGC GEORGE COBB (WLM 564)

SPECIFICATION FOR DRYDOCK REPAIRS

FY2025

Developed By: Adrian J Rubio

(Rev-0, 17 May 2024)

USCGC GEORGE COBB (WLM-175) DRYDOCK AVAILABILITY FY2025

ii (Rev-0)

TABLE OF CONTENTS

Revisions Record ........................................................................................................................................... v Consolidated List of References ................................................................................................................... vi Consolidated List of Government-furnished Property ............................................................................ xviii Consolidated List of Critical Inspection Items ........................................................................................... xxi Principal Characteristics - TENDER ........................................................................................................ xxii General Requirements WORK ITEM 1: Fire Prevention Requirements WORK ITEM 2: Hull Plating, U/W Body, Inspect WORK ITEM 3: Hull Plating, U/W Body, Ultrasonic Testing WORK ITEM 4: U/W Body, Preserve, Partial, Condition A WORK ITEM 5: U/W Body, Preserve, Partial, Condition B WORK ITEM 6: U/W Body, Preserve, Partial, Condition C WORK ITEM 7: Hull Plating Freeboard, Preserve, Partial WORK ITEM 8: Hull and Structural Plating, General, 12.75 lbs. Steel Plate, Renew WORK ITEM 9: Hull and Structural Plating, General, 15.3 lbs. Steel Plate, Renew WORK ITEM 10: Appendages, U/W, Leak Test WORK ITEM 11: Appendages, U/W, Internal, Preserve WORK ITEM 12: Chain Lockers, Clean and Inspect WORK ITEM 13: Tanks, Potable Water, Clean and Inspect WORK ITEM 14: Tanks, Lube Oil, Clean and Inspect WORK ITEM 15: Tanks, Ballast, Clean and Inspect WORK ITEM 16: Voids, Accessible, Clean and Inspect WORK ITEM 17: Tanks, Dirty Oil and Waste, Clean and Inspect WORK ITEM 18: Z-Drive Input Drive Shaft, Bearings Inspect WORK ITEM 19: Z-Drive Input Drive Shaft, Alignment Check WORK ITEM 20: Z-Drive Propulsion Unit, Renew, Drydock WORK ITEM 21: Z-Drive Coolers, Clean and Inspect WORK ITEM 22: Z-Drive Input Drive Shaft, Thrust Bearing Renewal WORK ITEM 23: Fathometer Transducer, Renew WORK ITEM 24: Sea Valves and Waster Pieces, Overhaul Or Renew WORK ITEM 25: Sea Strainers, Duplex, All Sizes, Overhaul WORK ITEM 26: Sea Strainers, Simplex, All Sizes, Clean and Inspect WORK ITEM 27: Sea Bay, Clean and Inspect WORK ITEM 28: Sea Bay, Preserve 100% WORK ITEM 29: Point of Use Potable Water Filters, Install WORK ITEM 30: Potable Water Pneumatic Tanks, Clean and Inspect WORK ITEM 31: Hot Water Accumulator Tanks, Clean and Inspect WORK ITEM 32: Compressed Air Receivers and System Valves, All, Clean, Inspect, Hydro and Lift . 133 WORK ITEM 33: Thruster Unit (General), Overhaul WORK ITEM 34: Hull Fittings (Weight Handling Rigging Hardware), Inspect and Test WORK ITEM 35: Anchor Windlass, Inspect And Service WORK ITEM 36: Anchor Chains and Ground Tackle, Inspect and Repair WORK ITEM 37: Anchors, Preserve WORK ITEM 38: Towing Bitts, Chocks, and Fairleads, Inspect and Test WORK ITEM 39: Hull Fittings (Mooring and Towing), Inspect and Test WORK ITEM 40: Grey Water Holding Tanks, Clean and Inspect WORK ITEM 41: Sewage Holding Tanks, Clean and Inspect WORK ITEM 42: Grey Water Piping, Clean and Flush iii (Rev-0)

WORK ITEM 43: Sewage Piping, Clean and Flush WORK ITEM 44: Tanks, Grey Water Holding, Preserve, Partial WORK ITEM 45: Tanks (Sewage Holding), Preserve, 100 percent WORK ITEM 46: Tanks (Sewage Holding), Preserve, Partial WORK ITEM 47: Tanks, Ballast, Preserve, 100 Percent WORK ITEM 48: Tanks, Ballast, Preserve, Partial WORK ITEM 49: Chain Locker, Preserve, 100 Percent WORK ITEM 50: Tanks, Dirty Oil and Waste, Preserve, 100 Percent, WORK ITEM 51: Tanks, Dirty Oil and Waste, Preserve, Partial, WORK ITEM 52: Tanks, Grey Water Holding, Preserve, 100 Percent WORK ITEM 53: Tanks, Potable Water Preserve, 100 Percent WORK ITEM 54: Tanks, Potable Water, Preserve, Partial, WORK ITEM 55: Decks – Exterior (Buoy or Construction Deck), Preserve 100% WORK ITEM 56: Superstructure, Preserve, 100 Percent WORK ITEM 57: Exhaust Stacks, Exterior, Preserve WORK ITEM 58: Cathodic Protection, Zinc Anodes, Renew, WORK ITEM 59: Drydock WORK ITEM 60: Temporary Services, Provide - Cutter WORK ITEM 61: Sea Trial Performance, Support, Provide WORK ITEM 62: Main Mast, Preserve, 100% WORK ITEM 63: Oily Water Separator, Replace WORK ITEM 64: Thruster Quick Disconnects (QDs), Install WORK ITEM 65: Bilges, Preserve WORK ITEM 66: Slip Resistant Sheets, Exterior Decks, Renew WORK ITEM 67: Watertight Doors and Scuttles, External, Renew WORK ITEM 68: Watertight Hatches, External DC Deck and Below, Renew WORK ITEM 69: Directional Control Valve, Upgrade WORK ITEM 70: Seawater Piping Anti-Fouling System, Install WORK ITEM 71: Doppler Speed Log, Upgrade WORK ITEM 72: Flame Detectors, Replace WORK ITEM 73: Deck Covering (Interior Wet/Dry), Renew WORK ITEM 74: Compartment Decks, Preserve WORK ITEM 75: Crew’s Quarters Racks, Renew WORK ITEM 76: Exterior Vent, Renew WORK ITEM 77: Hand Rail Stanchions Renew WORK ITEM 78: Compartment Insulation, General, Renew WORK ITEM 79: Single Point Davit Hydraulic Piping, Renew WORK ITEM 80: Auxiliary Sea Water (ASW) Valves, Renew WORK ITEM 81: 01 Level Deck Aft, Repair WORK ITEM 82: CO Cabin Window Renew WORK ITEM 83: Mechanical Remote Valve Operators, Renew WORK ITEM 84: Fairleads, Renew WORK ITEM 85: Independent NACE Inspector (Level 3), Provide WORK ITEM 86: Tenting, Provide WORK ITEM 87: Deck Tie Down, Renew WORK ITEM 88: Deck Covering, Electrical Matting, Renew WORK ITEM 89: Sewage Valves, Renew WORK ITEM 90: Forecastle Deck Flood Light Fdn, Renew WORK ITEM 91: Hose Bracket Repair WORK ITEM 92: Aircastle Repair WORK ITEM 93: Fwd Mast Ladder Renew iv (Rev-0)

WORK ITEM 94: Engine Intake Screen, Renew WORK ITEM 95: 02 Level Deck, Repair WORK ITEM 96: Vents 01-13-1 and 01-15-2, Renew WORK ITEM 97: Sewage Vent Piping, Renew WORK ITEM 98: Z-drive Steering Hydraulic Piping, Renewal WORK ITEM 99: Gooseneck Vent Piping, Renew v (Rev-0)

REVISIONS RECORD

This page is used to record specification revisions, which may have occurred subsequent to a Revision 0 (Rev-0) package. Information listed is intended to provide contractors and field unit personnel a means to ensure all the current specification revision pages are present when reviewing or utilizing this specification package.

DATE REV# WORK

ITEM#

CHANGES MADE

NOTE : All work item and paragraph numbers listed above for a given revision correspond to same numbers in the previous revision. This revised specification is self-contained with all of the above listed changes incorporated.

vi (Rev-0)

CONSOLIDATED LIST OF REFERENCES

The below-listed documents form a part of this specification to the extent specified herein. Approval/publication dates or revision dates/numbers are also identified, to ensure that same document versions are used at the time of specification writing and during contract execution.

All Coast guard drawings, technical publications, and standard specifications will be provided to contractors by the Coast Guard at an appropriate time, or upon request, free of charge. Other Government documents may be accessed – free of charge – from links located on the SFLC website. Commercial sites provide access to their respective documents.

COAST GUARD DRAWINGS

Coast Guard Drawing 154 WPC 256-201, Rev C, Main Propulsion Cooling System Arrangement

Coast Guard Drawing 154 WPC 505-201, Rev D, Piping Standards Booklet

Coast Guard Drawing 175 WLM 170-1, Rev H; Mast Arrangement & Details

Coast Guard Drawing 175 WLM 114-001, Rev D, Shell Appendages

Coast Guard Drawing 175 WLM 130-001, Rev -Mods to Buoy Deck Incidental to Hawser Pipe Cover

Coast Guard Drawing 175 WLM 162-1, Rev E, Stack A & D 1 & 2 Panels

Coast Guard Drawing 175-WLM-167-001, Rev L, Structural Closures

Coast Guard Drawing 175 WLM 180-011, Rev F, Sheet 5 Bow Thruster Foundation

Coast Guard Drawing 175 WLM 184-001, Rev A, V850 Transducer Adaptor Ring

Coast Guard Drawing 175 WLM 184-001, Rev-, CRP-V850 Transducer Adapter Ring

Coast Guard Drawing 175 WLM 184-001, V850 Transducer Adaptor Ring

Coast Guard Drawing 175 WLM 185-001, Rev -, Foundation Incidental to Boss 2.2 GPM OWS Installation

Coast Guard Drawing 175 WLM 202-002, Rev G, MPCMS Wiring Data (COED)

Coast Guard Drawing 175 WLM 243-001, Rev -, Propulsion Shafting Arrangement

Coast Guard Drawing 175 WLM 243-002, Rev F, Propulsion Shafting Arrangement

Coast Guard Drawing 175 WLM 243-1, Rev -, Propulsion Shaft Arrangement

Coast Guard Drawing 175 WLM 243-2, Rev F, Propulsion Shaft Arrangement

Coast Guard Drawing 175 WLM 245-001, Rev A, Propeller

Coast Guard Drawing 175 WLM 245-002, Rev A, Z-drive Propeller Details, Modified Design

Coast Guard Drawing 175 WLM 256-001, Rev J, Sea Water Cooling System Diagram

Coast Guard Drawing 175 WLM 256-001, Rev J, Seawater Cooling System Diagram

Coast Guard Drawing 175 WLM 256-001, Rev K, Seawater Cooling System Diagram

Coast Guard Drawing 175 WLM 256-001, Rev K, Seawater Cooling System Diagram.

Coast Guard Drawing 175 WLM 256-003, Rev D, Seawater Cooling System, A/D FR 61 - FWD, Hull Block 910, 920, 930

Coast Guard Drawing 175 WLM 256-004, Rev J, Sea Water Cooling System Arrangements and Details

Coast Guard Drawing 175 WLM 256-004, Rev J, Seawater Cooling System A/D HB 940, 950, 960, 970

Coast Guard Drawing 175 WLM 256-004, Rev J, Seawater Cooling System, A/D, H.B 940, 950, 960, 970 vii (Rev-0)

Coast Guard Drawing 175 WLM 256-004, Rev J, Sheets 5 and 13, Seawater Cooling System A & D, Hull Blocks 940-970

Coast Guard Drawing 175 WLM 256-012, Rev B, ASW System Piping Modification

Coast Guard Drawing 175 WLM 256-013, Rev A, Sea Bay Thermometer Installation

Coast Guard Drawing 175 WLM 262-001, Rev J, Lube Oil System Diagram

Coast Guard Drawing 175 WLM 262-002, Rev H, Waste Oil System Diagram

Coast Guard Drawing 175 WLM 262-005, Rev G, Lube Oil System A/D – Hull Blocks 910, 930, 940, &

Coast Guard Drawing 175-WLM 320-7, Rev R, Power System Deck Plan 01 Level & Above Hull Block 960 & 970 Partial Elementary & Block Wiring Diagrams (sheet 3)

Coast Guard Drawing 175 WLM 320-001, Rev AL, Electrical One-Line Diagram

Coast Guard Drawing 175 WLM 320-004, Rev G, Power System Deck Plan ER and Pump Rm Hull Block 920

Coast Guard Drawing 175 WLM 320-012, Rev -, Power System Mods Incidental to OWS Removal/Installation One-Line Diagram

Coast Guard Drawing 175-WLM 330-2, Rev F, Lighting System Frame 24 Forward, Hull Block 910 &

Coast Guard Drawing 175-WLM 422-1, Rev G, Navigation, Signal & Searchlight Block, Isometric and Arrangements

Coast Guard Drawing 175-WLM 422-2, Rev F, Navigation, Signal & Searchlight Elementary Wiring Diagram

Coast Guard Drawing 175 WLM 505-001, Rev C, General Requirements for Piping Systems

Coast Guard Drawing 175 WLM 505-002, Rev F, Mech Remote Valve Oprs A & D

Coast Guard Drawing 175 WLM 505-003, Rev B, Sea Connection Arrangements

Coast Guard Drawing 175 WLM 506-001, Rev G, Overflows, Air Escapes & Sounding Tubes Diagram

Coast Guard Drawing 175 WLM 533-001, Rev G, Potable Water System Diagram

Coast Guard Drawing 175 WLM 533-001, Rev H, Potable Water System Diagram

Coast Guard Drawing 175 WLM 533-006, Rev D, Independent Tank Potable Water Hb 950

Coast Guard Drawing 175 WLM 551-001, Rev J, Compressed Air System Diagram

Coast Guard Drawing 175 WLM 556-006, Rev E, RHIB Davit Hydraulic System A/D Hull Block 950, 960, 970

Coast Guard Drawing 175 WLM 561-001, Rev J, Z-drive Hydraulic System Diagram

Coast Guard Drawing 175 WLM 568-2, Rev M, Bow Thruster Assembly (Model 125 Fixed Pitch)

Coast Guard Drawing 175 WLM 573-001, Rev T, Buoy Deck Arrangement

Coast Guard Drawing 175 WLM 573-8, Rev D, ATON Tie Downs

Coast Guard Drawing 175-WLM-573-012, Rev A, Replacement ATON Tie Downs

Coast Guard Drawing 175 WLM 581-001, Rev E, Anchor Handling System Arrangement

Coast Guard Drawing 175 WLM 581-001, Rev F, Anchor Handling System Arrangement

Coast Guard Drawing 175 WLM 581-001, Rev F, Anchor Handling System

Coast Guard Drawing 175 WLM 582-001, Rev D, Mooring and Towing, A & D

Coast Guard Drawing 175 WLM 593-001, Rev G, Sewage & Waste Water System Diagram

Coast Guard Drawing 175 WLM 593-001, Rev G, Sewage and Waste Water System Diagram

Coast Guard Drawing 175 WLM 593-002, Rev H, Oily Bilge System Diagram viii (Rev-0)

Coast Guard Drawing 175 WLM 593-009, Rev E, Independent Tanks, Sewage Holding Tank

Coast Guard Drawing 175 WLM 593-013, Rev C, Oily Water Separator A&D

Coast Guard Drawing 175 WLM 593-014, Rev A, OWS System Operating Instructions BOSS 2.2T-107-

YM

Coast Guard Drawing 175 WLM 601-001, Rev L, General Arrangement and Inboard and Outboard Profiles

Coast Guard Drawing 175 WLM 601-001, Rev P, General Arrangement and Inboard and Outboard Profiles

Coast Guard Drawing 175 WLM 601-001, Rev T, General Arrangement Inboard & Outboard Profiles

Coast Guard Drawing 175 WLM 601-001, Rev T, General Arrangement Inboard and Outboard Profiles

Coast Guard Drawing 175 WLM 601-002, Rev H, Booklet of General Drawings (IDA LEWIS)

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet of General Drawings (552-564)

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet of General Plans

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet of General Plans

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet Of General Plans

Coast Guard Drawing 175 WLM 601-003, Rev L; Booklet Of General Drawings 552-564

Coast Guard Drawing 175 WLM 601-003, Rev N, Booklet of General Plans

Coast Guard Drawing 175 WLM 601-1, Rev N, Arrangement, Inboard And Outboard Profiles

Coast Guard Drawing 175 WLM 633-001, Rev D, Cathodic Protection

Coast Guard Drawing 175 WLM 635-001, Rev F, Hull Thermal and Acoustic Insulation Schedule

Coast Guard Drawing 175 WLM 635-001, Rev F, Hull, Thermal, & Acoustic Insulation Schedule

Coast Guard Drawing 175 WLM 801-001, Rev A, Hull Lines

Coast Guard Drawing 175 WLM 801-003, Rev A, Curves of Form

Coast Guard Drawing 175 WLM 801-006, Rev H, Docking Plan

Coast Guard Drawing 175 WLM 801-006, Rev J, Docking Drawing

Coast Guard Drawing 175 WLM 801-006, Rev J, Docking Plan

Coast Guard Drawing 175 WLM 801-015, Rev C, Scantlings, Decks & Platforms

Coast Guard Drawing 175 WLM 801-019, Rev C, Shell Expansion

Coast Guard Drawing 175 WLM 801-19, Rev C; Shell Expansion

Coast Guard Drawing 175 WLM 920-001, Rev K, Hull Block 920 Panels

Coast Guard Drawing 175 WLM 940-001, Rev J, Hull Block 940 Panels

Coast Guard Drawing 175 WLM 940-002, Rev K, Hull Block 940 Modules

Coast Guard Drawing 175 WLM 940-004, Rev J, Hull Block 940 - Transverse Frames & BHD

Coast Guard Drawing 175-WLM 960-1, Rev M, Hull Block 960 Panels

Coast Guard Drawing 175 WLM_320_001, Rev. AL, Electrical One-Line Diagram.

Coast Guard Drawing 175 WLM-528-001, Rev E, Plumbing and Interior Deck Drains Diagram

Coast Guard Drawing 175-WLM 256-5, Rev -, Z-Drive Lube Oil Heat Exchanger Tube Bundle Replcmnt & Piping Mods

Coast Guard Drawing 175-WLM 506-1, Rev G, Overflows, Air Escapes & Sounding Tubes Diagrams

Coast Guard Drawing 175-WLM 506-7, Rev D, Vents & Sounding Tubes Main Deck & Above a & D, Hull Block 970

Coast Guard Drawing 175-WLM 512-11, Rev D, HVAC a & D, FR 70-50, Main Deck & Above, Hull Block 960 ix (Rev-0)

Coast Guard Drawing 175-WLM 512-12, Rev C, HVAC a & D, Frame 70-88 Main Deck & Above, Hull Block 970

Coast Guard Drawing 175-WLM 512-13, Rev A, HVAC Std Details & General Instructions

Coast Guard Drawing 175-WLM 512-9, Rev A, HVAC a &D, Frame 88-61, Platform, Hull Block 940

Coast Guard Drawing 175-WLM 568-001, Rev B, Bow Thruster Arrangement & Detail

Coast Guard Drawing 175-WLM 256-001, Rev H, Seawater Cooling System Diagram

Coast Guard Drawing 175-WLM 256-001, Rev J, Seawater Cooling System Diagram

Coast Guard Drawing 175-WLM 256-003, Rev A, Seawater Cooling System, Fr 61 Fwd Blocks 910, 920, Coast Guard Drawing 175-WLM 256-003, Rev D, Seawater Cooling System, Fr 61 Fwd Blocks 910, 920, Coast Guard Drawing 175-WLM 256-004, Rev J, Seawater Cooling System A & D, Hull Blks 940-970

Coast Guard Drawing 175-WLM 256-012, Rev B, ASW System Piping Modifications

Coast Guard Drawing 175-WLM 436-1, Rev H, Fire & Smoke Detection System Block, Isometric, and Elementary Wiring Diagram (Circuit SM)

Coast Guard Drawing 175-WLM 551-5, Rev E, Compressed Air System a/D Hull Block 940, 950

Coast Guard Drawing 175-WLM 568-002, Rev N, Bow Thruster Detail

Coast Guard Drawing 175-WLM 601-01, Rev N, General Arr, Inboard & Outboard Profiles

Coast Guard Drawing 175-WLM 601-2, Rev N, Booklet of General Plans

Coast Guard Drawing 175-WLM 612-001, Rev G, Lifeline, Rails & Stanchions

Coast Guard Drawing 175-WLM 625-1, Rev K, Windows and Portlights

Coast Guard Drawing 175-WLM 631-2, Rev E, Painting Schedule

Coast Guard Drawing 175-WLM 635-001, Rev F, Hull Thermal and Acoustic Insulation Schedule

Coast Guard Drawing 175-WLM 635-1, Rev F, Hull Thermal & Acoustic Insulation Schedule

Coast Guard Drawing 175-WLM 801-15, Rev C, Scantlings, Decks & Platforms

Coast Guard Drawing 175-WLM 950-01, Rev G, Hull Block 950 Panels

Coast Guard Drawing 175-WLM-180-002, Rev H, Foundations Hull Block 910

Coast Guard Drawing 175-WLM-184-003, Rev. -, Structural Mods Incidental to Doppler DS60 Doppler Install

Coast Guard Drawing 175-WLM-320-001, Rev AP, Electrical One-Line Diagram

Coast Guard Drawing 175-WLM-423-002, Rev. T, Electronic Navigation System Coed.

Coast Guard Drawing 175-WLM-423-007, Rev. B, DGPS Installation Wiring Data (Coed)

Coast Guard Drawing 175-WLM-424-003, Rev. -, Doppler Speed Log System Replacement, Ripout, Installation, Arrangement, Wiring and Details

Coast Guard Drawing 175-WLM-437-007, Rev R, Buoy Dk Control Sys Block, ISO & Elem Wrg Diag

Coast Guard Drawing 175-WLM-505-002 Rev F Mechanical Remote Valve Operators Arrangement and Details

Coast Guard Drawing 175-WLM-529-002 Rev G Main Drainage System Diagram

Coast Guard Drawing 175-WLM-573-013, Rev -, Replacement DCV Amplifier Card Wiring Diagram

Coast Guard Drawing 180-TE-0103-005. Rev M, Booklet of General Plans

Coast Guard Drawing 225B WLB 601-002 Rev K, Booklet of General Drawings

Coast Guard Drawing FL 533-001, Rev B, Placard Potable Water Flush

Coast Guard Drawing FL 533-002, Rev -, Point of Use Water Filter Install x (Rev-0)

Coast Guard Fleet Drawing FL 2804-12, Rev -, U.S.C.G. Emblem

Coast Guard Fleet Drawing FL 2804-22, Rev-, Consolidated Visual ID for Cutters

NAVSEA Drawing 167-7379842, Rev A, Procedure & Welding Sequence for Non-Ballistic, Watertight & Airtight Quick Acting or Individually Dogged Personnel Doors

NAVSEA Drawing 804-5959214, Rev-, Piping Insulation - Installation Details

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) 10360.3 (series), Coatings and Color Manual

Coast Guard Commandant Instruction (COMDTINST) 9000.6 (series), Naval Engineering Manual

Coast Guard Commandant Instruction (COMDTINST) 9077.1 (series), Equipment Lockout/Tags-Plus Instruction

Coast Guard Commandant Instruction (COMDTINST) M10360.3, Jun 2006, Coatings and Colors Manual

Coast Guard Commandant Instruction (COMDTINST) M9077.1C, 1995, Equipment Tag-Out Procedures

Coast Guard Maintenance Procedure Card (MPC) A-A-14033, Dec 2017, Buoy Chain Winch Wire Rope Weight

Coast Guard Technical Publication (TP) 3498, Section A, Jul 2015, Buoy Chain Winch

Coast Guard Technical Publication (TP) 3498, SWBS 573, Aug 2019, Buoy Chain Winch

Coast Guard Technical Publication (TP) 3605A, Nov 2007, MPCMS Operating Manual (Volume 1)

Coast Guard Technical Publication (TP) 3605B, SWBS 86; Section B; Machinery Plant Control & Monitor System (MPCMS) Z-Drive Direction Indicator System Technical Manual

Coast Guard Technical Publication (TP) 3621, SWBS 436, June 2020, Fire Detection System - Operation, Installation and Maintenance Manual, July 2020

Coast Guard Technical Publication (TP) 3628, Mar 2017; Vol 4 of 9, Instruction Manual, Bow Thruster

Coast Guard Technical Publication (TP) 3628, SWBS 568, Section A, March 2017, Bow Thruster – (Bird-Johnson Company)

Coast Guard Technical Publication (TP) 3631, Section 581-A, Sep 2013, Manufacturer's Instruction Book-SWBS Groups 573-581, Anchor Windlass

Coast Guard Technical Publication (TP) 3653, Jul 2013; SWBS 245, Section A; Z-Drive - Model 1350-H

Coast Guard Technical Publication (TP) 3653, Jul 2013; SWBS 245, Section A; Z-DRIVE - MODEL 1350-H

Coast Guard Technical Publication (TP) 3653, Jul 2013; SWBS 245, Section A; Z-drive - Model 1350-H

Coast Guard Technical Publication (TP) 8001B, SWBS-633, Section-A, 2018, Cathodic Protection System – Model CA44227

Coast Guard Technical Publication TP-10500, Doppler Sonar – Model DS-60

Coast Guard Technical Publication TP-3446, Doppler Speed Log, Model SRD-500 Dual Axis

Fire Prevention and Response

MIL-STD 1689(A) Fabrication, Welding and Inspection of Ships Structure

Naval Ships’ Technical Manual (NSTM), Chapter 074, Volume 3, 2019, Gas Free Engineering

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 0000, 2020, General Requirements

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 0740, 2020, Welding and Allied Processes xi (Rev-0)

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 3042, 2020, Shipboard Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 6310, 2020, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2014, General Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2018, General Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2020, General Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), Latest Version, General Requirements

Surface Forces Logistics Center Standard Specification 0000, (SFLC Std Spec 0000) 2020 Edition, General Requirements

Surface Forces Logistics Center Standard Specification 0174 (SFLC Std Spec 0174), 2014, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2014, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2018, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2020, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and Allied Processes.

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), Latest Version, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740, (SFLC Std Spec 0740) 2020, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3041), 2014, Shipboard Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3041), 2020, Shipboard Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3041, (SFLC Std Spec 3041) 2020, Shipboard Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3042 (SFLC Std Spec 3042), 2014, Shipboard Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification 3042 (SFLC Std Spec 3042), 2020, Shipboard Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification 3042, (SFLC Std Spec 3042) 2020, Shipboard Electrical Cable Removal, Relocation, Splice, Repair and Installation

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2018, Auxiliary Machine Systems xii (Rev-0)

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2020 Auxiliary Machine Systems

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2020, Auxiliary Machine Systems

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), 2022, Fire Prevention and Response

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), Latest Version, Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2014, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2018, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2020, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Preserve Ship Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), Latest Version, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310, (SFLC Std Spec 6310) 2020, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6341 (SFLC Std Spec 6341), 2020, Install Interior Deck Covering Systems

Surface Forces Logistics Center Standard Specification 8634 (SFLC Std Spec 8634), 2022, Drydocking

Surface Forces Logistics Center Standard Specification 8635 (SFLC Std Spec 8635), 2020, Temporary Services

Surface Forces Logistics Center Standard Specification 8636 (SFLC Std Spec 8636), 2014, Temporary Hull Accesses

Surface Forces Logistics Center Standard Specification 8636 (SFLC Std Spec 8636), 2020, Temporary Hull Accesses

Surface Forces Logistics Center Standard Specification 8636 (SFLC Std Spec 8636), 2022, Temporary Hull Accesses

OTHER REFERENCES

225-WLB Doppler Sonar DS-60 System Operation Verification Test (SOVT)

3.1 General

3.1.1 CIR. The Contractor must submit a CIR for the inspections listed in the following paragraph(s):

3.1.2 Tech Rep. The Contractor must provide the services of a Furuno authorized/ licensed Tech Rep for the DS60 Doppler Speed Log System to accomplish the following on site:

3.1.2.1 Ensure the Tech Rep is an OEM Certified Representative for the system/equipment stated above and is demonstrated on their résumé.

3.1.3 Protective measures. The Contractor must furnish and install all protective measures in accordance with SFLC Std Spec 0000, paragraph 3.3.3 (Vessel component, space, and equipment protection).

3.1.4 Interferences. The Contractor must handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). Known interferences include, but are not limited to the following:

xiii (Rev-0)

3.1.4.1 Visual inspection

3.1.4.1 Visual inspection. The Contractor must visually inspect exposed areas after interferences are removed. Notify Contracting Officer (KO) or designated representative if damage or excessive corrosion is found. Submit a CIR.

American Bureau of Shipping (ABS) Approved Chain, Accessory and Bar Manufacturing Facilities List, Oct 2016

American National Standards Institute/American Water Works Association (ANSI/AWWA) C652, 2011, Disinfection of Water-Storage Facilities

American National Standards Institute/American Water Works Association (ANSI/AWWA) C652, 2019, Disinfection of Water-Storage Facilities

American National Standards Institute/NSF International (ANSI/NSF) 61, 2008, Drinking Water System Components - Health Effects

American National Standards Institute/NSF International (ANSI/NSF) 61, 2015, Drinking Water System Components - Health Effects

American Society for Testing and Materials (ASTM) International F1508, 2016, Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services

American Society of Mechanical Engineers (ASME) B16.34, 2004, Valves-Flanged, Threaded, and Welding End

American Society of Mechanical Engineers (ASME) B16.34, 2017, Valves-Flanged, Threaded, and Welding End

American Welding Society (AWS) D1.2, 2014, Structural Welding Code - Aluminum

ASTM International (ASTM) A106, 2015, Standard Specification for Seamless Carbon Steel Pipe, for High-Temperature Service

ASTM International (ASTM) D1330, 2004, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D1330, 2010, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D1330, 2015, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D3359, 2009, Standard Test Methods for Measuring Adhesion by Tape Test

ASTM International (ASTM) D4138, 2013, Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means

ASTM International (ASTM) D5363, 2016, Standard Specification for Anaerobic Single-Component Adhesives (AN)

ASTM International (ASTM) F683, 2014, Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery

ASTM International (ASTM) F992, 2006, Standard Specification for Valve Label Plates

ASTM International (ASTM) F992, 2017, Standard Specification for Valve Label Plates

Cableways and cables

Coast Guard Commandant Instruction (COMDTINST) M10360.3, Jun 2006, Coatings and Colors Manual

Code of Federal Regulations (CFR) Title 29, Part 1910, Occupational Safety and Health Standards

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for Shipyard Employment

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for Shipyard Employment

Code of Federal Regulations (CFR) Title 40, Protection of the Environment xiv (Rev-0)

Commercial Item Description (CID) A-A-59313, Nov 2003, Thread Compound; Anti-seize, Zinc Dust- Petrolatum

Commercial Item Description (CID) A-A-59316, 2016, Abrasive Materials; for Blasting

Commercial Item Description (CID) A-A-59588, 2005, Rubber Silicone

Commercial Item Description (CID) A-A-59588, Jul 2005, Rubber Silicone

Commercial Item Descriptions (CID) A-A-59316, Nov 2003 Abrasive Materials for Blasting

Compartment Check Off List: WLM 175 – 564 (GEORGE COBB)

Federal Specification (Fed Spec) DDD-C-95, Mar 1972, Carpets and Rugs, Wool, Nylon, Acrylic, Modacrylic

Federal Specification (Fed Spec) HH-P-151, Mar 1991, Packing; Rubber-Sheet, Cloth-Insert

Federal Specification (Fed Spec) RR-C-271, Rev E, Dec 2010, Chain and Attachments, Welded and Weldless

Federal Specification (Fed Spec) RR-C-271, Rev E, Mar 2016, Chains and Attachments, Carbon and Alloy Steel

Insulation

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-61, 2013 Edition, Pressure Testing Of Steel Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-61, 2019 Edition, Pressure Testing Of Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-67, 2017 Edition, Butterfly Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72, 1999 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72, 2010 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72, 2018 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service

Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2008 Edition, Bronze Gate, Globe, Angle and Check Valves

Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2013 Edition, Bronze Gate, Globe, Angle and Check Valves

Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2019 Edition, Bronze Gate, Globe, Angle and Check Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), SP-58, 2009, Pipe Hangers and Supports – Materials, Design, Manufacture, Selection, Application and Installation

MIL-A-18001, May 2005, Anodes, Sacrificial Zinc Alloy (Commercially Accepted - ASTM B418)

MIL-A-22262, Mar 1996; Abrasive Blasting Media Ship Hull Blast Cleaning

MIL-A-46106, Jun 1992, Adhesive-Sealants, Silicone, Rtv, One-Component

MIL-C-24633, Oct 2014, Chain, Stud Link, Anchor, Low Alloy Steel, Flash Butt Welded

MIL-DTL-23549, Sep 2016, Grease, General Purpose

MIL-F-24402, May 1995, Filters (Hydraulic), Filter Elements (High Efficiency), and Filter Differential Pressure Indicators, General Specification

Military Specification MIL-A-22262B, March 1996, Abrasive Blasting Media Ship Hull Blast Cleaning xv (Rev-0)

Military Standard MIL-S-19622/17D, Dec 1992, Stuffing Tube, Nylon, and Packing Assemblies, General Specification for

Military Standard MIL-STD-2003/2A(SH), Sep 2009, Electrical Plant Installation Standard Methods for Surface Ships and Submarines, (Equipment).

Military Standard MIL-STD-2003/3A (SH), Sep 2009, Electrical Plant Installation Standard Methods for Surface Ships and Submarines, (Penetration).

Military Standard MIL-STD-2003/4A (SH), Sep 2009, Electrical Plant Installation Standard Methods for Surface Ships and Submarines, (Cableways).

MIL-PRF-1149, Jun 1998, Gasket Materials, Synthetic Rubber, 50 and 65 Durometer Hardness

MIL-PRF-16173, Sep 2006, Corrosion Preventive Compound, Solvent Cutback, Cold-Application

MIL-PRF-24647, 2013, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jun 2006, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jun 2006, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-S-45180, 1998, Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant

MIL-STD-2003-3, Sep 2009, Electric Plant Installation Standard Methods for Surface Ships & Submarines (Penetrations)

MIL-STD-2003-4, Sep 2009, Electric Plant Installation Standard Methods for Surface Ships & Submarines (Cableways)

Naval Sea Systems Command (NAVSEA) Underwater Ship Husbandry Manuals (UWSH) S0600-AA- PRO-160, Nov 2011, Chapter 16, Cofferdams

Naval Sea Systems Command (NAVSEA) Underwater Ship Husbandry Manuals (UWSH) S0600-AA- PRO-160, Nov 2011, Chapter 16, Cofferdams

NAVSEA Drawing 2803-980209, Plates, Label

NAVSEA Drawing 804-5773931, Rev A, Acoustic & Thermal Insulation For Compartments Installation Details

NAVSEA Drawing 804-5773931, Rev-A, Insulation for Compartments, Acoustic and Thermal – Installation Details

NAVSEA Technical Publication T9074-AD-GIB-010/1688, (TP 1688), July 2012, Requirements for Fabrication, Welding, and Inspection of Submarine Structure

Piping

Pre-Installation Test Check Out (PITCO) WLB-225 SRD-500 Doppler Speed Log Replace PITCO

Provide manufacturer's proprietary system/equipment information, software, and tools.

Recovered Energy, Inc, BOSS 107 Separator System Operation & Maintenance Manual – YM Model

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183, 2013, Cork and Rubber Composition Sheet; For Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183, 2019, Cork and Rubber Composition Sheet; For Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183B, 2019, Cork and Rubber Composition Sheet; For Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) G-6032, 2020 Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric

Society of Automotive Engineers (SAE) AMS-G-6032, August 2012, Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2004, Solvent Cleaning xvi (Rev-0)

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2016, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), 2015, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2004, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2012, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), 2004, Power Tool Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), 2004, Power Tool Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), Power Tool Cleaning)

The Society for Protective Coatings (SSPC) Surface Preparation Standard No. 11 (SSPC-SP 11), 2013, Power-Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC), January 2015, Paint Application Specification No. 2 (PA-2), Procedure for Determining Conformance to Dry Coating Thickness Requirements

The Society for Protective Coatings (SSPC), Paint Application Specification No. 2 (PA-2), Procedure for Determining Conformance to Dry Coating Thickness Requirements

The Society for Protective Coatings (SSPC)/NACE International (NACE) 2007, Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, Near-White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No.2, 2007, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 6/NACE No. 3, 2007, Commercial Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 7/NACE No.4, 2007, Brush-Off Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-2/NACE WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-4/NACE WJ-4, 2012, Waterjet Cleaning of Metals – Light Cleaning

The Society for Protective Coatings (SSPC)/NACE Joint Surface Preparation Standard SSPC-SP 10/NACE No.2, 2004, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2004, Near-White Blast Cleaning xvii (Rev-0)

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 12/NACE No. SSPC-SP 12/NACE No.5, Surface Preparation and Cleaning of Steel & Other Hard Materials by High and Ultrahigh Pressure Water Jetting Prior to Recoating

The Society for Protective Coatings SSPC-SP 10/NACE No.2, Near-White Blast Cleaning xviii (Rev-0)

CONSOLIDATED LIST OF GOVERNMENT-FURNISHED PROPERTY

The following is a list of property, which the Government will furnish. This list supersedes any other material obligations indicated or implied by referenced drawings.

WORK

ITEM

MTI ITEM DESCRIPTION NSN/PN QTY ESTIMATED

COST

($/UNIT)

19 Y Z Drive Alignment

Tool NSN: 5220-01-F16-4720 1 ea. $3600.00

20 Y Starboard Z-drive (CCW rotation)

NSN: 2010-21-920-0919 1 ea. $500,250.00

20 Y Port Z-drive (CW rotation)

NSN: 2010-21-920-0899 1 ea. $500,250.00

20 Y Z Drive Alignment Tool

NSN: 5220-01-F16-4720 1 ea. $3600.00

20 N Thrustmasters Technical

Representative

N/A N/A N/A

22 N #3 Thrust Bearing Cooper Bearing, 02BCP110MMGR

NSN: 3040-01-F12-2610 2 ea. $10,902.00

23 N ***Fathometer Transducer, Shallow Water, 50-200 kHz

(Airmar Technology

SS505)

NSN: 5845-01-470-2500 1 ea. $343.63

29 N Water Filter Assembly PN: DWS160-L (3M) NSN:

(ACN) 44330-01-F20-5959

6 ea. $160.00

29 N Water Filter Element PN: 56134-44 (3M) 6 ea. $180.00 29 N Placard - Potable Water

Flush N/A 8 ea. $50.00

33 N Seal Kit, Thruster NSN: 2010-01-555-9048 1 ea. $4376.00 33 N Anode, Zinc NSN: 5365-01-495-5350 9 ea. $113.75 33 N **Seal Spacer

(B125SM44178)

NSN: 2010-01-495-6823 1 ea. $700.00

33 N **Shaft Sleeve NSN: 2010-01-495-2638 1 ea. $5702.40 35 N Anchor Windlass

Overhaul kit NSN: 5430-01-546-4684 1 ea. $9,677.05

35 N Ball Valve NSN: 4820-01-013-3430 1 ea. $38.55 35 N Valve, Counterbalance NSN: 4820-01-F16-4571 PN:

CBEH-LKN-BCL Sun Hydraulics Corp

1 ea. $202.85

35 Y ** Motor, Hydraulic NSN: 4320-01-419-3520 1 ea. $2,577.98 35 N ** Valve, Linear, Directional Control NSN: 4810-01-511-3173 1 ea. $2,343.85

35 Y Hydraulic Brake NSN: 2530-01-F14-4033 P/N:

90B3C4G087

1 ea $1,189.44

59 Y *Transducer Cover Plate

N/A 2 ea. $50.00 xix (Rev-0)

63 N Boss 2.2 GPM OWS NSN: 4330-01-F13-3461 PN:

BOSS 2.2T-107 YM

1 ea. $14,300.00

69 N Directional Control Valve (DCV)

NSN: 4810-01-F19-5719 PN:

4WRE10E75-2X/G24K4/V

1 ea. $1748.00

69 N Amplifier Card NSN: 5996-01-F19-5720 PN:

VT-VRPA2-2-1X/V0/T1

1 ea. $1552.00

69 N Mating Connector, 4P

G4WIF PG7 SW

NSN: 5935-01-F19-5722 PN:

R900023126

1 ea. $46.00

70 N MGPS Shipset, (Including: EB/NS/2W

Control panel, PN:

PAPEBSB02W (1 EA),

9” Coper Anode, PN:

PAAZRRY037FT (2 EA),

Nylon Mounting Sleeve, PN: PAW004 (2 EA), On

Board Spare Kit, PN:

PAY001 (1 EA) and

Installation/ Operation Manuals, PN: PAX020 (2

EA).

NSN: N/A PN: PA102149 1 ea. *** $5,860.00

71 N Main Display Unit NSN: 7025-01-678-5218 PN:

DS600

1 ea $2,525.00

71 N Electronics Distribution Unit

NSN: 5895-01-678-5147 PN:

DS610

1 ea $6,670.00

71 N Electronics Transceiver Unit

NSN: 5845-01-678-5160 PN:

DS620

1 ea $9,750.00

71 N Gate Valve Assembly NSN: 4820-01-678-5058 PN:

DS661

1 ea $15,750.00

71 N Dual-Axis Transducer NSN: 5848-01-678-5056 PN:

DS630-30

1 ea $7,700.00

71 N Doppler Shell Ring NSN: 5340-01-F19-5622 PN:

DS661-1

1 ea $5,225.00

71 N Furuno 7-Pin Cable NSN: 5995-01-530-4744 PN:

000-154-028

1 ea $82.40

72 Y Semiconductor Device, Photo

NSN: 5961-01-599-4004 PN:

20/20MI-11SF

9 ea. 1,489.00

72 N Bracket, Mounting NSN: 5340-01-599-4015 PN:

20/20-005 (ST.ST.316L)

9 ea. $45.55

82 N Window, Fixed, 24”W x 18”H, CRES 316, ES Marine Type-K-325-F

02625901-16 1 ea. $500.00

83 N **Deck Box:

¾” size w/10 turns, weld-in, cam-lock cover included

BFG P/N: VCDB-1200-10 2 ea. $576.00

83 N **90° Gear Box:

¾” size, bronze

BFG P/N: VCG-3200 3 ea. $402.00

83 N **Consolidated Hinged Joint:

¾” size, manganese

BFG P/N VCK-1200 1 ea. $439.95 xx (Rev-0) bronze housing, sst shafts

83 N **U-Joint 1-¼” OD x ¾” bore, steel

BFG P/N VCU-1142 16 ea. $110.99

83 N **Valve Coupling Rising Handwheel, ¾” male

BFG P/N: VCU-3200 1 ea. $82.75

83 N **Valve Coupling Rising Stem, ¾” male

BFG P/N: VCM-2200 1 ea. $139.00

87 N Coast Guard (C-G) P/N

CGRD50TDRASS01

Assembly of bowl, D- Ring and strap. Rated

Load 12,300 lbs.

NSN# 2020-01-682-7587 15 ea. $150

*Government-loaned property, which shall be returned to the vessel upon completion of the availability.

**New or refurbished equipment that the Government may provide for installation in place of existing equipment.

***Government-furnished property, which is to be supplied by either the vessel or the C4IT ServiceCenter xxi (Rev-0)

CONSOLIDATED LIST OF CRITICAL INSPECTION ITEMS

The following is a list of work items, which contain Critical Inspection reports, which the Contractor must complete within the first 25% of the availability contract period (see SFLC Std Spec 0000, paragraph 3.2.6.5 (Inspection report particulars)):

Work Item

Title

3 Hull Plating, U/W Body, Ultrasonic Testing

10 Appendages, U/W, Leak Test

12 Chain Lockers, Clean and Inspect

15 Tanks, Ballast, Clean and Inspect

20 Z-Drive Propulsion Unit, Renew, Drydock

25 Sea Strainers, Duplex, All Sizes, Overhaul

26 Sea Strainers, Simplex, All Sizes, Clean and Inspect

27 Sea Bay, Clean and Inspect

32 Compressed Air Receivers and System Valves, All, Clean, Inspect, Hydro and Lift

35 Anchor Windlass, Inspect And Service

36 Anchor Chains and Ground Tackle, Inspect and Repair

59 Drydock

65 Bilges, Preserve

69 Directional Control Valve, Upgrade

71 Doppler Speed Log, Upgrade

74 Compartment Decks, Preserve xxii (Rev-0)

PRINCIPAL CHARACTERISTICS - TENDER

175' WLM, BUOY TENDER

PHYSICAL

Length overall 174' 8" Length between perpendiculars 155' 1" Depth 14' 8" Maximum beam 36' 0" Designed draft 8' 0" Mast height (above 8' waterline) 58' 8" Frame spacing 20" Full load displacement 855.15 Long Tons SW Light load displacement 719.78 Long Tons SW Minimum op condition displ 852.19 Long Tons SW

HULL

Hull material Steel

MACHINERY

Main propulsion Two Caterpillar 3508 DITA V-8 diesel; 999 BHP ea @ 1500 RPM

Two Ulstein 360 degree steerable Z-Drives, 403 SRPM @ 1600 ERPM

Reduction gears Two Z-Drive units, Cardan shafting; 3.973:1 gear ratio Shaft seal John Crane Type ND Shaft bearings Five pedestal mounted, Cooper split roller bearings Number of propellers 2 Number of blades 4 Diameter 57.1" Rudders None; Z-drive Ship's service generators Three Caterpillar Model 3406 DITA Turbocharged; 285KW, 450V, 60 Hz, 1800

RPM

Emergency diesel generator One Caterpillar Model 3406 DIT 210 KW, 24V, 60 Hz, 1800 RPM

TANK CAPACITIES

Diesel oil capacity (100%) 16,385 gal Fresh water capacity (100%) 7,339 gal Lubricating oil (100%) 86 gal

1 (Rev-0)

00000_0623_FLT

REC_00000_FLT_Commercial Project @ Contractor’ Facility (0121)

General Requirements

1. SCOPE

1.1 Intent. This standard specification invokes general requirements for conducting Vessel repairs performed for assets under MATOC by Commercial Contractor at Commercial Facility for Coast Guard vessels.

1.2 Term interchangeability. The terms 'Contractor', 'CG Yard', 'NAVSTA EVERETT', 'shipyard', 'Base', and 'Coast Guard Industrial' are used interchangeably in this specification. Where the primary service provider is Coast Guard personnel, references to contractor and other noted descriptors within this specification or within drawings, publications, SFLC Standard Specifications or other commercial and military references are deemed the same as prime service provider.

2. REFERENCES

COAST GUARD DRAWINGS

None

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) M10360.3 (series), Coatings and Color Manual

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), Latest Version, General Requirements

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), Latest Version, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), Latest Version, Fire Prevention and Response

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), Latest Version, Requirements for Preservation of Ship Structures

OTHER REFERENCES

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for Shipyard Employment

NAVSEA Technical Publication T9074-AD-GIB-010/1688, (TP 1688), July 2012, Requirements for Fabrication, Welding, and Inspection of Submarine Structure

2 (Rev-0)

3. REQUIREMENTS

3.1 General. The Contractor must conform to all requirements specified in SFLC Std Spec 0000 and in this item, as applicable, during the performance of this availability. The requirements in this WI applies to all work under the scope of this contract, whether explicitly stated in all following work items or not, and to all other work subsequently authorized by changes, modifications, or extensions to the contract.

3.1.1 The Contractor must conform to all requirements specified in SFLC Std Spec 5550 and in the Fire Protection and Response work item, as applicable, during the performance of this availability.

3.1.1.1 Fire Safety Plan submission. The Contractor must submit a copy of the CFR 1915, Subpart P, Fire Safety Plan with the Contractor’s bid when work will be conducted in a Contractor–owned facility. Include any MOA(s) with local firefighting facilities.

3.1.1.2 Fire Plan submission. The Contractor must submit a copy of the developed availability specific fire plan as requested in the Fire Protection and Response work item, with the Contractor’s bid.

NOTE

NAVSEA drawings listed will be available FOR INSPECTION ONLY from the Coast Guard Port Engineer post-award. SFLC will not redistribute NAVSEA documents.

Contractors can apply to NAVSEA headquarters directly for copies.

3.2 Fire watch requirements. The Contractor must refer to 3.3.1.3 (Fire watch requirements) of SFLC Std Spec 0000, in accomplishing the following task:

Provide portable fire extinguishers for Coast Guard fire watch personnel. Coast Guard fire watch is in lieu of contractor personnel during the hours of 0800-1600, Monday through Friday, and limited to two Coast Guard fire watch personnel.

Provide fire watch personnel and fire extinguishers for the duration of the availability period, during and beyond noted Coast Guard fire watch support.

3.3 Preservation requirements. The Contractor must accomplish all preservation tasks, including touch-ups, in accordance with SFLC Std Spec 6310.

3.3.1 Brand name approval. Ensure that all contractor-furnished coatings are in accordance with SFLC Std Spec 6310, Appendix C (Authorized Coatings for Use on Cutters and Boats).

3.3.2 Coating colors and system color schemes. The Contractor must obtain a written KO authorization to deviate from any coatings required in SFLC Std Spec 6310 Appendix C before work.

3.3.3 In-process quality control measures. The Contractor must abide by all the safety, preservation, and quality control requirements specified in SFLC Std Spec 0000, paragraph…