Attachment_2_Chiller_Cutsheet.pdf

Technical Data Sheet for C-1 & 2

Job Number: R75GEC Page Prepared Date: 6/23/2021 Job Name: Lake Mead Interagency Center

Chiller Replacement 4 of 17 www.DaikinApplied.com

Job Information Technical Data Sheet

Job Name Lake Mead Interagency Center Chiller Replacement

Date 6/23/2021

Submitted By Gavin Helm

Software Version 12.10

Unit Tag C-1 & 2

Unit Overview

Model Number

Max Capacity ton

Voltage Unit Starter Type

ASHRAE 90.1* LEED Enhanced Refrigerant Management Credit

AGZ041E 33.56 208 V / 60 Hz / 3 Ph Across the Line '07, '10, '13 & '16 Pass

Unit

Unit Type Platform Unit Revision

Air-Cooled Scroll Compressor Chiller Packaged 0A

Head Pressure Tubing

VFD w/o Line Reactors [Low Ambient] Replaceable Filter Dryer with Discharge & Liquid Valves, with

HGBP

Unit Controls Display

Electronic Expansion Valve On Controller only

Refrigerant Type Refrigerant Weight

R410A 46 lb (per unit)

Pump Controls

Dual Evaporator Pumps - Dual Control Output

Approval

ETL/cETL, AHRI & ASHRAE 90.1

Evaporator

Water Volume: 1.9 gal Connection Hand: Left Hand Connections

Connection Size: 2.5 in Insulation: Single Layer Insulation to Suction at each Compressor

Entering Fluid Temperature

Leaving Fluid Temperature

Fluid Type Fluid Flow

Fluid Flow Min / Max

Pressure Drop

Pressure Drop Min / Max

Fouling Factor

57.30 °F 45.00 °F Water 65.10 gpm

36.6/ 152.4 gpm

4.15 ft H₂O

1.10 / 15.2 ft H₂O

0.000100 °F.ft².h/Btu

Note: Evaporator Pressure Drop includes Factory Installed Strainer. Pressure drop without strainer is 3.3. Minimum flow is based on a Variable Flow Pumping System Type and applies to part load conditions only.

Condenser

Coil Fins: MicroChannel Guards: Condenser Coil Wire Grilles only

Design Ambient Air Temperature Altitude Fan Diameter Minimum Design Ambient Temperature

115.0 °F 2500 ft 30.0 in 20.0 °F

Image may not represent ordered unit

For Review

10/05/2021 8:32:07 AM

5 of 17 www.DaikinApplied.com

Unit Performance

Performance Points rated at User Defined DPLV Load Points

Unit Evaporator Condenser

Point # % Load Max

Capacity

% Load Request Capacity

Capacity ton

Input Power kW

IPLV.IP

* (EER)

Btu/W.h

% DPLV

Weighting

DPLV

Btu/W.h

Efficiency

(EER)

Btu/W.h

Fluid Flow gpm

Pressure Drop ft H₂O

Entering Fluid

°F

Leaving Fluid

°F

Ambient Air °F

Altitude ft

Max 100.0 33.56 53.94 17.80 7.466 65.30 3.30 57.30 45.00 115.0 2500

1 99.5 100.0 33.40 53.67 1 15.40 7.468 65.10 3.30 57.30 45.00 115.0 2500

2 74.6 75.0 25.05 25.86 42 11.63 65.10 3.30 54.20 45.00 92.5 2500

3 49.8 50.0 16.70 11.47 45 17.47 65.10 3.30 51.10 45.00 70.0 2500

4 24.9 This point is below the chiller minimum load without hot gas bypass (HGBP) but will run here with use of HGBP

Supplemental Performance Data for Unit Operation at AHRI Conditions

Performance Points at AHRI Standard Condition

Capacity Input Power Efficiency (EER) IPLV.IP* (EER)

38.12 ton 43.28 kW 10.57 Btu/W.h 17.80 Btu/W.h

Performance Points rated at AHRI

Unit Evaporator Condenser

Point # % Load Capacity ton

Input Power kW

Efficiency (EER) Btu/W.h

Fluid Flow gpm

Entering Fluid °F

Leaving Fluid °F

Ambient Air °F

Altitude ft

1 100 38.12 43.28 10.57 91.2 54.00 44.00 95.0 0.000

2 75 28.59 23.16 14.82 91.2 51.50 44.00 80.0 0.000

3 50 19.06 11.64 19.65 91.2 49.00 44.00 65.0 0.000

4 25 9.531 5.221 21.90 91.2 46.50 44.00 55.0 0.000

* IPLV reflects AHRI standard rating conditions with water and does not change with user defined conditions

Note: Evaporator Pressure Drop in this table does Not include strainer. For strainer pressure drop data see 'Evaporator' table on page 1.

Sound (with insulation)

Type of Sound Insulation: Low Noise (Sound Reduction Compressor Blankets)

Sound Pressure (at 30 feet)

63 Hz dB

125 Hz dB

250 Hz dB

500 Hz dB

1 kHz dB

2 kHz dB

4 kHz dB

8 kHz dB

Overall dBA

75% Load dBA

50% Load dBA

25% Load dBA

57 57 56 57 50 48 47 43 58 57 55 54

Sound Power

63 Hz dB

125 Hz dB

250 Hz dB

500 Hz dB

1 kHz dB

2 kHz dB

4 kHz dB

8 kHz dB

Overall dBA

75% Load dBA

50% Load dBA

25% Load dBA

84 84 83 84 77 75 74 70 85 84 82 81 Octave band is non 'A' weighted and overall readings are 'A' weighted. Sound data rated in accordance with AHRI Standard-370.

Physical

Unit

Length* Height Width* Shipping Weight* Operating Weight*

94 in 100 in 88 in 2948 lb 2964 lb

* Shipping and operating weights do not include the weights of any Options or Accessories. Contact Chiller Applications for additional information.

6 of 17 www.DaikinApplied.com

Electrical

Unit Electrical Data

Voltage Starter Type Fan Motor Quantity LRA Fan Motor (each) FLA Fan Motors (each)

208 V / 60 Hz / 3 Ph Across the Line 4 23 A 5.8 A

Power Connection Type: High Short Circuit Current Rating with Single Point Disconnect Switch and Circuit Protection Short Circuit Current Rating: 65 kA

Single Point Power Connection

Minimum Circuit Ampacity

(MCA):

182 A

Recommended Overcurrent Protection Size:

200 A

Maximum Overcurrent Protection Size(MOCP):

200 A

Lug Connection Size: (1) 4 - 300 MCM

Compressor Electrical Data

Compressor Type Compressor Quantity Starter Type

Scroll 4 Across the Line

Circuit #: 1 2

Compressor #: 1 3 2 4

Rated Load Amps (RLA): 34 A 34 A 34 A 34 A

Inrush Current: 240 A 240 A 240 A 240 A

Note: Power wiring connections to the chiller may be done with either copper or aluminum wiring. Wire should be sized per NEC and/or local codes. Wire sizing and wire count must fit in the power connection lug sizing listed above. Please contact your local sales office for more information.

Options

Basic Unit

Control Box Ambient: High Ambient with Exhaust Fans (125ºF maximum) Suction Shut-off Valve: Included

Evaporator Strainer: Factory Installed Evaporator Strainer – 175 PSI Pressure Rating

Control

Communication: BACnet MS/TP

Electrical

Unit Options: 115V Convenience Outlet Water Flow Indicator: Thermal Dispersion Type

Warranty

Unit Startup Domestic

Standard Warranty: 1st Year Entire Unit Parts only

Extended Compressor Warranty: Compressor Only; extended 4 years parts only (5 Years Total)

AHRI Certification

Certified in accordance with the AHRI Air-Cooled Water-Chilling Packages Certification Program, which is based on AHRI Standard 550/590 (I-P) and AHRI Standard 551/591 (SI). Certified units may be found in the AHRI Directory at www.ahridirectory.org

Accessories

Optional

Part Number Description

332325101 RIS Isolator Kit; AGZ: Packaged, Microchannel,Al&Cu Fins, 030-071E (non-Seismic),25-65D,30-65C;

M'Chnl,75-101E (non-S'mc); Al Fin,70C/D;Remote,Al&Cu Fin,30-70E (non-S'mc); Pump Pkg, M'Chnl&Al Fin,30-65E (non-S'mic); Cu Fin,30-55E(non-S'mic)

331776661 Base Frame Grilles; AGZ: 030-071E (without Pump Package)

7 of 17 www.DaikinApplied.com

AGZ-E Close Spacing_Drawing for C-1 & 2

8 of 17 www.DaikinApplied.com

AGZ-E Cl ose S paci ng_Drawi ng for C -1 & 2

AGZ-E Close Spacing Performance 0A

The graphs below are based on individual cases and should not be combined with other scenarios

Case 1: Building or Wall on One Side of Unit

Assumes a solid height wall taller than unit. Refer to Case 4 for partial wall openings

Building or Wall on One Side of Unit

For models AGZ030-101E, maintain a 4 feet minimum from a wall of any height.

For models AGZ110-130E, maintain a 6 feet minimum from a wall of any height.

For models AGZ140-241E, maintain an 8 feet minimum from a wall of any height.

Case 2: Two Units, Side-by-Side

For models 030-180, there must be a minimum of 4 feet between two units placed side-by-side; however, performance may be affected at this distance. For models 191-241, the minimum is 6 feet as closing spacing may cause air recirculation and elevated condenser pressure.

Assuming the requirement of one side having at least 8 feet of service clearance is met, Case 2 figures show performance adjustments as the distance between two units increases.

Two Units, Side-by-Side

Case 2 - Full Load Capacity Reduction

Case 2 – Power Increase

Product Drawing Unit Tag: C-1 & 2

13600 Industrial Park Blvd. Minneapolis, MN 55441 www.DaikinApplied.com Software Version: 12.10

Product: Air-Cooled Scroll Chiller Project Name:

Model: AGZ-E Sales Office: Norman Wright Mech. Equip.

Corp. Sales Engineer: Gavin Helm June 23, 2021 Ver/Rev: Sheet 1 of 1 Scale: NTS Tolerance: +/-1.0” Dwg Units: in [mm] No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

9 of 17 www.DaikinApplied.com

Case 3: Three or More Units, Side-by-Side

For all models, there must be a minimum distance between any units placed side-by-side; however, performance may be affected at this distance. Minimum distances are: models 030 to 070 - 4 feet, models 075 to 101 - 5 feet, models 110 to 241 - 6 feet. The Case 3 charts below depict Case 3 performance adjustments as the distance between units increases. Data shown is for the middle unit with a unit on each side.

See Case 2 adjustment factors for the two outside units.

Three or More Units, Side-by-Side

Case 3 – Full Load Capacity Reduction

Case 3 – Power Increase

10 of 17 www.DaikinApplied.com

Case 4: Open Screening Walls

Decorative screening walls are often used to help conceal a unit either on grade or on a rooftop. When possible, design these walls such that the combination of their open area and distance from the unit (see chart below) do not require performance adjustment. If the wall opening percentage is less than recommended for the distance to the unit, it should be considered as a solid wall. It is assumed that the wall height is equal to or less than the unit height when mounted on its base support. If the wall height is greater than the unit height, see Case 5: Pit Installation for performance adjustment factors. The distance from the sides of the unit to the side walls must be sufficient for service, such as opening control panel doors. For uneven wall spacing, the distance from the unit to each wall can be averaged providing no distance is less than 4 feet. Values are based on walls on all four sides.

Case 4 - Allowable Wall Open Area

Case 5: Pit Installation

Pit installations can cause operating problems resulting from air recirculation and restriction and require care that sufficient air clearance is provided, safety requirements are met and service access is provided. A solid wall surrounding a unit is substantially a pit and this data should be used. Derates are based on single chiller installation only.

Steel grating is sometimes used to cover a pit to prevent accidental falls or trips into the pit. The grating material and installation design must be strong enough to prevent such accidents, yet provide abundant open area to avoid recirculation problems. Have any pit installation reviewed by the Daikin Applied sales representative prior to installation to ensure it has sufficient air-flow characteristics and approved by the installation design engineer to avoid risk of accident.

Models AGZ030-070E:

The Case 5 figures for models AGZ030-070E show adjustment factors for pit/wall heights of 4 feet, 5 feet, and 6 feet.

Case 5 - Full Load Capacity Reduction and Power Increase

(AGZ030E-070E)

Case 5- Pit Installation

KEY:

- - - - - - - - - - : Power Increase ______________: Capacity Reduction

11 of 17 www.DaikinApplied.com

Models AGZ075-130E:

The Case 5 figures for models AGZ075-130E show adjustment factors for pit/wall heights of 5 feet, 6 feet, and 8 feet.

Case 5 - Full Load Capacity Reduction and Power Increase (AGZ075-130E)

KEY:

- - - - - - - - - - : Power Increase ______________: Capacity Reduction

Models AGZ140-241E:

The Case 5 figures for models AGZ140-241E show adjustment factors for pit/wall heights of 6 feet, 8 feet, and 10 feet.

Case 5 - Full Load Capacity Reduction (AGZ140-180E)

Case 5 - Power Increase (AGZ140-211E)

Case 5 - Full Load Capacity Reduction (AGZ190-241E)

Case 5 - Power Increase (AGZ225-241E)

Jo b

N am e

Jo b

N u m b e r:

A G

Z0

-07

E_C n d G rl_w rp s_D raw in g fo r C -1

Lake M ead

In teragen cy C en te r

C h iller R ep lace m en t

R

EC

o f 1

P age re p are d D ate w w .D aikin A p p lied .co m

/2

/2

AGZ040 -070E_ CndGrl_wr ps_ Drawing for C-1 & 2

Product Drawing Unit Tag: C-1 & 2 Sales Office: Norman Wright Mech. Equip. Corp.

Product: Air-Cooled Scroll Chiller Project Name: Lake Mead Interagency Center Chiller Replacement

Sales Engineer: Gavin Helm Model: AGZ040-071E June 23, 2021 Ver/Rev: Sheet: 1 of 1 Scale: N/A Tolerance: N/A Dwg Units: N/A No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

00 AGZ-E Guards: Condenser Coil Wire Grilles, Front and Rear Wraps, Painted Base

Diagram Notes

Diagram simulates wrap, grille and louver options as selected only. Refrigeration components may vary depending on selected options.

N am e

Jo b

N u m b

Z0

E_P K

G _M

C C

_D raw in g fo r C -1

In teragen cy C en te r

C h iller R ep lace m en t

R o p are d D w .D aikin A p p lied

/2

AGZ041E_ PKG_MCC_Draw ing for C -1 & 2

Sales Engineer: Gavin Helm Model: AGZ041E June 23, 2021 Ver/Rev: Sheet: 1 of 1 Scale: NTS Tolerance: +/- 1.0" Dwg Units: in [mm] No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

0A AGZ041E Packaged (Microchannel Condenser) Unit Dimensions

PACKAGE UNITS WITH MICROCHANNEL COILS

UNIT MODEL

CG LOCATION, IN (MM)

X Y Z

AGZ041E 39.8 (1011) 45.9 (1166) 38.4 (975)

AGZ046E 38.9 (988) 44.5 (1130) 41.2 (1047)

AGZ051E 39.1 (993) 44.9 (1141) 41.2 (1047)

AGZ056E 39.1 (993) 44.8 (1138) 41.2 (1047)

AGZ061E 39.2 (996) 44.6 (1133) 41.1 (1044)

AGZ066E 39.2 (996) 44.6 (1133) 41.1 (1044)

AGZ071E 36.8 (935) 41.8 (1062) 42.6 (1082)

NOTE

LIFTING WEIGHTS ARE BASED ON UNIT

SHIPPING WEIGHT. MOUNTING WEIGHTS

ARE BASED ON UNIT OPERATING WEIGHT

WITH EVAPORATOR WATER INCLUDED.

SHIPPING AND OPERATING WEIGHTS DO

NOT INCLUDE THE WEIGHTS OF ANY

OPTIONS OR ACCESSORIES.

PACKAGE UNITS WITH MICROCHANNEL COILS

UNIT

MODEL

SHIPPING WEIGHT OPERATING WEIGHT LIFTING (SHIPPING) WEIGHT BY CORNER LBS (KG) MOUNTING (OPERATING) WEIGHT LBS (KG)

LBS (KG) LBS (KG) L1 L2 L3 L4 M1 M2 M3 M4

AGZ041E 2948 (1337) 2964 (1345) 1067 (484) 881 (400) 548 (249) 453 (206) 1022 (464) 844 (383) 601 (273) 496 (225)

AGZ046E 3094 (1403) 3112 (1412) 1051 (477) 832 (377) 676 (307) 535 (243) 1021 (463) 809 (367) 715 (324) 567 (257)

AGZ051E 3093 (1403) 3114 (1413) 1049 (476) 837 (380) 671 (304) 536 (243) 1020 (463) 814 (369) 712 (323) 568 (258)

AGZ056E 3106 (1409) 3128 (1419) 1052 (477) 840 (381) 675 (306) 539 (245) 1023 (464) 817 (371) 716 (325) 572 (260)

AGZ061E 3130 (1420) 3155 (1431) 1059 (480) 851 (386) 676 (307) 543 (246) 1031 (468) 828 (376) 718 (326) 577 (262)

AGZ066E 3130 (1420) 3155 (1431) 1059 (480) 851 (386) 676 (307) 543 (246) 1031 (468) 828 (376) 718 (326) 577 (262)

AGZ071E 3472 (1575) 3497 (1586) 1180 (535) 847 (384) 842 (382) 604 (274) 1157 (525) 830 (377) 880 (399) 631 (286)

UNIT

MODEL

EVAP. DIMENSIONS IN (MM)

CONNECTION SIZE

(VICTAULIC)

A

(NO STRAINER)

B

(WITH STRAINER)

AGZ041E 23.5 (597) 2.3 (58) 2.5 (64)

AGZ046E 23.2 (589) 2.0 (51) 2.5 (64)

AGZ051E 22.2 (564) 1.0 (25) 2.5 (64)

AGZ056E 21.5 (546) 5.3 (135) 2.5 (64)

AGZ061E 20.5 (521) 4.3 (109) 2.5 (64)

AGZ066E 20.1 (511) 3.9 (99) 2.5 (64)

AGZ071E 19.1 (485) 2.9 (74) 2.5 (64)

N am e

Jo b

N u m b

ZE_C

learan ce _M

C C

D raw in g fo r C

-1 &

In teragen cy C en te r

C h iller R ep lace m en t

R o p are d D w .D aikin A p p lied

/2

AGZ-E Service Clearance

*NOTE: Additional clearance may be required for proper airflow. Please consult Close Spacing drawings and IOM for additional details.

AGZE_Cleara nce_MCC_Dra wing for C -1 & 2

Sales Engineer: Gavin Helm Model: AGZ-E June 23, 2021 Ver/Rev: Sheet: 1 of 1 Scale: NTS Tolerance: +/- 1.0" Dwg Units: in [mm] No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

0B

FieldWiring_AGZE_SP_Drawing for C-1 & 2

15 of 17 www.DaikinApplied.com

FieldWiri ng_AGZE_S P_Drawi ng for C -1 & 2

Field Wiring Diagram Unit Tag: C-1 & 2

Product: Air-Cooled Scroll Project Name: Lake Mead Interagency Center Chiller Replacement Model: AGZ030-241E Single-Point Sales Office: Norman Wright Mech. Equip.

Corp. Sales Engineer: Gavin Helm June 23, 2021 Ver/Rev: Sheet 1 of 1 Scale: N/A Tolerance: N/A Dwg Units: N/A

No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

AGZ030-241E Single-Point Connection Field Wiring Diagram

0D

N am e

Jo b

N u m b

Iso K it_ R

IS_33

_D raw in g fo r C

-1 &

In teragen cy C en te r

C h iller R ep lace m en t

R o p are d D w .D aikin A p p lied

/2

IsoKit_RIS_332 32510 1_Drawi ng for C -1 & 2

Accessory: Rubber-in-Shear (RIS) Isolator Kit Project Name: Lake Mead Interagency

Sales Engineer: Gavin Helm Kit Part Number: 332325101 June 23, 2021 Ver/Rev: Sheet: 1 of 1 Scale: NTS Tolerance: +/- 1.0" Dwg Units: in [mm] No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

00 Rubber-in-Shear (RIS) Isolator Kit Dimensions and Placement

Mounting Location

M1 M2 M3 M4

Brown Brown Brown Brown

M3

M1

C o n tr o l P a n el

M4 M2