Attachment_1_Statement_of_Work.pdf

Bureau of Land Management Statement of Work (SOW) Law Enforcement Upfitting

Equipment installation for 2024 RAM 2500 “Makens”, VIN: 3C6TR5CJ5RG318751. All equipment to be provided by the Contractor unless indicated with “X” in the below list.

Front Grill/Front Quarter Panel/Rear Quarter Panel (On Bed) Line Item

Provided "X"

Quantity Description

1 One Install 30” or similar low profile bar: Red and Blue LED flashing light strip in/on/ behind grill.

2 Four Install Side facing Red and Blue LED light heads, surface mount / low profile lights (red/blue) on left and right quarter panels front and rear.

3 Install Chassis Unlimited Diablo Series Winch Bumper to replace OEM 4 Install 30” high performance White light LED Bar in front slot of above bumper, Baja

Designs ONX6 Straight racer bar or similar, with spot light pattern.

5 Install Siren speaker behind grill / bumper 6 Install Wig-Wag Flasher Control for Headlights TWO (high beam). Wired into headlights.

7 Three Install LED pods into cut outs of each side of bumper cut outs as follows: All the way on outside (closest to fender on each side, 3” Baja Designs Squadron Pro Black, white light LED light pod, angled slightly down and outboard to serve as a cornering or cutting light. Center light, forward facing Amber 3” Baja Designs Squadron Racer edition, amber light LED light pod, for use in dusty conditions. Closest to center line, Baja Designs Squadron-R Pro Infrared LED light pod facing forward for nighttime/no light driving.

8 Install Whelen Arges remote spotlight Driver side front fender

Rear bed/Tailgate/Bumper Line Item

Provided "X"

Quantity Description

9 Two Install surface mount red and blue flashing emergency lights on rear tailgate to side of LE emblems.

10 Install Truck Vault part number T-DGRAMMO-19S-P5-PW 6’4” magnum Height Offset Drawers, all weather box, with long and short assorted dividers.

11 Install or fabricate and install a tire mount and offroad jack mount on top of passenger side of Truck vault as well as tie down slots for a jack. Jack would be mounted horizontally toward the front of the bed, tire mounted toward tailgate (driver side top of truck vault should be clear of these items and flat.

12 Install Armordillo CR-Z Chase rack. Install appropriate rear facing white LED’s in slots to illuminate rear and cargo area.

13 Two Wire white LED Flood backup lights (IP68 minimum rated) mounted flush to rear bumper, one rocker switch to activate both lights in items 4&5.

14 Install rear and side facing low profile red and blue lights on rear and side of chase rack.

15 Install on top side angle cuts to chase rack, install a Baja Designs S2 Pro Black, white LED auxiliary light pod driver and passenger side, angled at 45 degrees down toward the ground as a work light on the side of the vehicle. Controls for this should be tied into same controls as ally lights on light bar (right and left).

16 Install DV8 steel rear bumper with flush mounted LED light cubes, and install back-up sensors (Americantrucks.com part number HR7732, see included picture).

17 Directly behind passenger side support arm of the chase rack, mount (#Priovided) Weboost Drive OTR Antenna, Route approximately 15 feet of corresponding coaxial antenna cable to center console area.

Roof Line Item

Provided "X"

Quantity Description

18 Install 53” TOMAR Style lightbar. Flashing Red & blue, one solid red ( CA Compliant), full flood with spot lights directly over driver and passenger seat.

19 X Two Install radio antennas as provided SATRAD and Motorola mobile radio antenna.

Route wiring as necessary.

Vehicle Striping/Decals Line Item

Provided "X"

Quantity Description

20 X Install all vehicle striping / decals will be placed as in drawings included with striping kit.

Interior/Dash Line Item

Provided "X"

Quantity Description

21 X Install GPS navigation mount w/ power hard wired to main console power block (Garmin, #provided) OVERHEAD console. Plug pigtails on dash. Typically used with 12V outlet under dash. (PROVIDED) GPS must not make contact with computer or truck controls. And be mounted as to not obscure too much visibility from driver. Intended location is above radio attached to Bullet point RubiGrid v2 mount.

22 Three Install LED Dome light (red/white). X1 over center console wired on rheostat, x1 over rear driver passenger side area (switched on passenger side c pillar), x1 installed over prisoner seat (switched at console)

23 Install Whelen Arges control head. Location to be determined.

24 Install bullet point RubiGrid V2 metal dash mount with 2x 1” ball mounts (for ram mount phone holders, and 2 ich ball for Garmin GPS.

25 Install Weboost 5G booster, with interior antenna located on dash where phone mounts will be. Booster itself can be mounted where feasible and out of the way

Center Console Line Item

Provided "X"

Quantity Description

26 Metal floor plate between seats for mounting console 27 X Install Jotto AK-12 style console with swing arm installed as necessary. Ensure computer in full stowed position does not contact dash/ac controls etc. Computer is a Dell 5430 Rugged with a Havis dock (#provided). Driver is 6’01”, 250 lbs and wears a right hand drop leg holster. Mount center console slightly toward passenger side if possible.

28 Install adjustable arm rest.

29 X Install & wire – Computer mount.

30 Install master console power auto-off timer.

31 X Install Motorola APX mobile radio; wired as to not lose encryption when off.

32 Two Install magnetic mic behind rocker switches for Satrad and Motorola radio mic.

33 Leave additional Space/plates for additional radio(s), if applicable.

34 Install Whelen Core S control system or similar.

35 Install PA mic/system (attached to siren control box, mic mounted with Mag Mic) ideal location would be mounted to passenger side front of console

36 Install Control Switch Panel towards the front: Min. of 7 heavy duty Rocker switches on console from left to right:

• Front off-road light bar

• Front Led Amber cubes

• Front angled white LED cubes

• Rear prisoner cage

• Rear bed cargo lights/LED cubes in rear Bumper

• Front IR Lights

• Blackout Switch 37 Three 12 volt, 3 plug auxiliary power ports at rear of center console.

38 X Install Motorola Handheld battery charger to side of console and wire to 12v ignition power.

39 Install Flush mount 2 port USB charge socket.

40 Disconnect – Door chime (If applicable).

41 Install switched “Blackout” to all exterior lighting including brake lights, rear bed lights and tow/trailer lights. No visible external light when “Blackout” engaged.

42 Placement of equipment front to back: Rocker switches for auxiliary lighting 2x magnetic mic mounts for Motorola control/mic and PA system, cup holder slot, 12v auxiliary ports x3. If there is reasonable excess room in console, an indented storage slot for things like pens.

43 Install Blue Sea Split bus 12-fuse block w/ground distribution PT series 30A time delay relay 12v (or something bigger as appropriate due to lighting and electronics in build).

Driver-side and Behind Console Line Item

Provided "X"

Quantity Description

44 Install rifle and shotgun mount and 2 locks with a 10 second timer. Rifle to be mounted on passenger side on console between seat and console if possible in a Black Rack lock, shotgun to be mounted vertical behind in front of rear partition.

45 Two Install switches that unlock both gun locks accessible by driver/passenger, PLUS a master cutoff switch mounted in a concealed location (to disable gun lock switch).

Switches must not interfere with seatbelt or safety devices.

Behind Front Passenger Seat/Under Rear Seat/Under Hood Line Item

Provided "X"

Quantity Description

46 Provide Master auxiliary power/fuse block or box for all aftermarket electronics to access fuses (all fuses labeled) that is easily accessible.

Prisoner Transport Cage Line Item

Provided "X"

Quantity Description

47 Replace right rear passenger factory interior panel with metal door panel.

48 Install steel window barrier in right rear and left passenger window.

49 Deactivate right rear passenger door lock and window controls but leave operable from driver door controls.

50 Install Rear/downward facing white LED flush/low profile mounted into prisoner cage aimed at prisoner’s face & body.

51 Install/Modify sufficient venting/air flow to prisoner transport area.

52 Install steel rear window guard.

Rear Passenger Seat Area Line Item

Provided "X"

Quantity Description

53 Install Setina #10VS RP coated poly partition (part number PK0355DRT192500CC) mount as far rearward as possible.

54 Install Setina Cargo deck with drawer Max, with single prisoner jump seat and cage (part number WK0514DRT102500)

55 Install 1000-1500 Watt pure sine inverter with USB and 110V outlets (minimum of w of each outlet.

56 Three Install 12v accessory plugs.

57 Wire a stand-alone (does not power anything else) 12v line for the Satrad base.

**All major electronics in this area should be easily accessible and removable if needed.

The Contractor shall inspect, adjust, repair, remove, and replace equipment as specified. The vehicle and all provided equipment shall be securely while in the Contractor’s possession. The Contractor is responsible for consulting BLM for clarification when needed and shall provide recommendations for additional equipment not identified in the Statement of Work, as well as notify BLM of any excess or unnecessary equipment.

Recommendations for alternative locations and/or more suitable components and equipment will be evaluated.

All work should be completed within 60 days of award.

The Bureau of Land Management will be responsible for vehicle delivery to and from the Contractor.

Contractor facility must be within 200-mile radius of BLM’s Tucson Field Office, 3201 East Universal Way, Tucson, AZ 85756. Upon successful inspection and release of both vehicles, the Contractor may submit a final invoice through the Invoice Processing Platform (IPP). The invoice shall include:

• Date

• Invoice number

• License plate number

• Odometer reading

• Line item for each part removed and installed, to include make, model, descrip on, and

• quan ty

• Clear documenta on for all work completed

• Warranty informa on

• Total invoice amount

FRONT

1)White 3” BD cube light 2)Amber 3” BD cube light

3) IR 3” BD Cube light

4) 30” BD 30” white light bar

2024 Ram Power Wagon BLM Plate# I626184

SIDE

REAR

Chase Rack:

1) Provide white rear facing LED lights for cargo area, tied into cubes in rear bumper.

2) Install BD LED cubes facing toward ground along angled face of chase rack as a work light.

3) Install red and blue flashers into back of rack in lieu of lights on rear of cab

Prisoner Cage:

Rear driver storage:

1. Radio Base

2. SAT Rad base

3. Inverter (always able to be on)

4. 12v accessory ports (always live)

Truck vault and deck:

1. Tire mount, center screw cap type, mounted flat toward tailgate. Must be spaced to accommodate 35 -37 inch tires (leave some room)

2. A steel container to contain an offroad jack, that can be secured and strapped down

3. General mounting location for cell booster mast

Console:

Jotto AK-12 workstation/ computer mount:

Dash Mount:

1. 1” ball for phone holder

2. 1” ball for phone holder

3. 2” ball for GPS

Rear DV8 Bumper: