Attachment 1 - Specifications Tenderfoot Swine Pen Floor Document-21Dec23.pdf

“Tenderfoot” swine pen flooring

2” thick with 1” X 1/2” diamond shaped openings – Able to hold up to 300-pound animals

Each module will require either:

2 notched half sections or

1 notched half section + 1 rectangular quarter section + 1 notched quarter section

See diagram below. 2” X 2” section removed

Width

Half (notched) Length of Half Section

Quarter (rectangular) Length of Quarter Section

Quarter (notched) Length of Quarter Section

A second notched half section could replace the 2 quarter sections.

Small Modules Overall pen dimensions - 53-3/8” X 62-1/4”

Half section – 53-3/8” X 31-1/8”

Quarter section – 53-3/8” X 15-9/16”

Each of the half sections need two 2” X 2” sections removed from the corners on one side of the long dimension (53-3/8”).

Half of the quarter sections need two 2” X 2” sections removed from the corners on one side of the long dimension (53-3/8”).

The other half of the quarter sections need to remain rectangular.

See diagram below. 2” X 2” section removed

53-3/8” (53-1/8”)

Half 31-1/8” (30-7/8”)

All RED numbers are from tab to tab.

The decking must fit within this area.

Green numbers are current sizes of finished decking. All finished tolerances must be +/-1/8”

Quarter 15-9/16” (15-7/16”)

Quarter 15-9/16” (15-7/16”)

The removed 2” X 2” sections in the corners are to fit around half of a 4” x 4” post. These sections may butt up against similar decking on any side. All finished tolerances must be +/-1/8”

Large Modules Overall pen dimensions – 64-1/2” X 62-1/2”

Half panel – 64-1/2” X 31-1/4”

Quarter panel – 64-1/2” X 15-5/8”

All RED numbers are from tab to tab. The decking must fit within this area.

Each of the half sections need two 2” X 2” sections removed from the corners on one side of the long dimension.

Half of the quarter sections need two 2” X 2” sections removed from the corners on one side of the long dimension.

The other half of the quarter sections need to remain rectangular.

See diagram below. 2” X 2” section removed

64-1/2”

Half 31-1/4”

Quarter 15-5/8”

Quarter 15-5/8”

The removed 2” X 2” sections in the corners are to fit around half of a 4” x 4” post. These sections may butt up against similar decking on any side.

All numbers provided for the large modules are from tab to tab. The decking must fit within this area.

All finished tolerances must be +/-1/8”

Small Module Decking Order

Mockup – With the provided measurements listed above for Small Modules fabricate the below listed sections. We have gone through this process with these modules and have found with the product we used that we needed to subtract ¼” from the long sides for both the half and quarter sections and ¼” from the short sides on the half sections and 1/8” from the short sides on the quarter sections. Red numbers listed are the maximum measurement and the green numbers are the numbers used for the latest design. Products may vary and we need to do mockups to ensure we have the correct measurements for your product. This may require more than one mockup.

For the mockup we need:

2 small module half sections with two 2” X 2” sections removed from the corners on one of the 53-3/8” (53-1/8”) sides.

1 small module quarter section with two 2” X 2” sections removed from the corners on one of the 53- 3/8” (53-1/8”) sides.

1 small module quarter section which is rectangular.

See Small Module diagram above.

Current dimensions for the decking we have used are in green.

Following successful mockup(s) we may then order up to:

76 small module half sections with two 2” X 2” sections removed from the corners on one of the 53-3/8” (53-1/8”) sides.

25 small module quarters with two 2” X 2” sections removed from the corners on one of the 53-3/8” (53-1/8”) sides.

25 small module quarters which are rectangular.

Large Module Decking Order

Mockup - With the provided measurements listed above for Large Modules fabricate the below listed sections. We have gone through this process with some of the small modules and have found with the product we used that we needed to subtract ¼” from the long sides for both the half and quarter sections and ¼” from the short sides on the half sections and 1/8” from the short sides on the quarter sections. Products may vary and we need to do mockups to ensure we have the correct measurement for your product. This may require more than one mockup.

For the mockup we need:

2 large module half sections with two 2” X 2” sections removed from the corners on one of the 64-1/2” sides.

1 large module quarter section with two 2” X 2” sections removed from the corners on one of the 64- 1/2” sides.

1 large module quarter section which is rectangular.

See Large Module diagram above.

Following successful mockup(s) we may then order up to:

40 additional large module half sections with two 2” X 2” sections removed from the corners on one of the 64-1/2” sides.

13 additional large module quarter sections with two 2” X 2” sections removed from the corners on one of the 64-1/2” sides.

13 large module quarter sections which are rectangular.

Bidding

Your bid must include separate costs for:

1. Small module mockup(s)

2. Small Module large-scale production

3. Large module mockup(s)

4. Large Module Large-scale production

Please include all costs including shipping in your bid.